[PATCH v2 08/12] ARM: assembler: add optimized ldr/str macros to load variables from memory

[Ard Biesheuvel <ardb@kernel.org>]

We will be adding variable loads to various hot paths, so it makes sense
to add a helper macro that can load variables from asm code without the
use of literal pool entries. On v7 or later, we can simply use MOVW/MOVT
pairs, but on earlier cores, this requires a bit of hackery to emit a
instruction sequence that implements this using a sequence of ADD/LDR
instructions.

Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
---
 arch/arm/include/asm/assembler.h | 45 ++++++++++++++++++--
 arch/arm/kernel/entry-armv.S     |  2 +-
 arch/arm/kernel/entry-header.S   |  2 +-
 3 files changed, 43 insertions(+), 6 deletions(-)

diff --git a/arch/arm/include/asm/assembler.h b/arch/arm/include/asm/assembler.h
index 1b9d4df331aa..2095638b7140 100644
--- a/arch/arm/include/asm/assembler.h
+++ b/arch/arm/include/asm/assembler.h
@@ -568,12 +568,12 @@ THUMB(	orr	\reg , \reg , #PSR_T_BIT	)
 	/*
 	 * mov_l - move a constant value or [relocated] address into a register
 	 */
-	.macro		mov_l, dst:req, imm:req
+	.macro		mov_l, dst:req, imm:req, cond
 	.if		__LINUX_ARM_ARCH__ < 7
-	ldr		\dst, =\imm
+	ldr\cond	\dst, =\imm
 	.else
-	movw		\dst, #:lower16:\imm
-	movt		\dst, #:upper16:\imm
+	movw\cond	\dst, #:lower16:\imm
+	movt\cond	\dst, #:upper16:\imm
 	.endif
 	.endm
 
@@ -611,6 +611,43 @@ THUMB(	orr	\reg , \reg , #PSR_T_BIT	)
 	__adldst_l	str, \src, \sym, \tmp, \cond
 	.endm
 
+	.macro		__ldst_va, op, reg, tmp, sym, cond
+#if __LINUX_ARM_ARCH__ >= 7 || \
+    (defined(MODULE) && defined(CONFIG_ARM_MODULE_PLTS)) || \
+    (defined(CONFIG_LD_IS_LLD) && CONFIG_LLD_VERSION < 140000)
+	mov_l		\tmp, \sym, \cond
+	\op\cond	\reg, [\tmp]
+#else
+	/*
+	 * Avoid a literal load, by emitting a sequence of ADD/LDR instructions
+	 * with the appropriate relocations. The combined sequence has a range
+	 * of -/+ 256 MiB, which should be sufficient for the core kernel and
+	 * for modules loaded into the module region.
+	 */
+	.globl		\sym
+	.reloc		.L0_\@, R_ARM_ALU_PC_G0_NC, \sym
+	.reloc		.L1_\@, R_ARM_ALU_PC_G1_NC, \sym
+	.reloc		.L2_\@, R_ARM_LDR_PC_G2, \sym
+.L0_\@: sub\cond	\tmp, pc, #8
+.L1_\@: sub\cond	\tmp, \tmp, #4
+.L2_\@: \op\cond	\reg, [\tmp, #0]
+#endif
+	.endm
+
+	/*
+	 * ldr_va - load a 32-bit word from the virtual address of \sym
+	 */
+	.macro		ldr_va, rd:req, sym:req, cond
+	__ldst_va	ldr, \rd, \rd, \sym, \cond
+	.endm
+
+	/*
+	 * str_va - store a 32-bit word to the virtual address of \sym
+	 */
+	.macro		str_va, rn:req, sym:req, tmp:req, cond
+	__ldst_va	str, \rn, \tmp, \sym, \cond
+	.endm
+
 	/*
 	 * rev_l - byte-swap a 32-bit value
 	 *
diff --git a/arch/arm/kernel/entry-armv.S b/arch/arm/kernel/entry-armv.S
index 1a6cf711a3b4..7f7ac963445c 100644
--- a/arch/arm/kernel/entry-armv.S
+++ b/arch/arm/kernel/entry-armv.S
@@ -53,7 +53,7 @@ UNWIND(	.setfp	fpreg, sp		)
 	subs	r2, sp, r0		@ SP above bottom of IRQ stack?
 	rsbscs	r2, r2, #THREAD_SIZE	@ ... and below the top?
 #ifdef CONFIG_VMAP_STACK
-	ldr_l	r2, high_memory, cc	@ End of the linear region
+	ldr_va	r2, high_memory, cc	@ End of the linear region
 	cmpcc	r2, r0			@ Stack pointer was below it?
 #endif
 	movcs	sp, r0			@ If so, revert to incoming SP
diff --git a/arch/arm/kernel/entry-header.S b/arch/arm/kernel/entry-header.S
index 81df2a3561ca..268f7f4c5c05 100644
--- a/arch/arm/kernel/entry-header.S
+++ b/arch/arm/kernel/entry-header.S
@@ -445,7 +445,7 @@ THUMB(	it	ne						)
 	@ in such cases so just carry on.
 	@
 	str	ip, [r0, #12]			@ Stash IP on the mode stack
-	ldr_l	ip, high_memory			@ Start of VMALLOC space
+	ldr_va	ip, high_memory			@ Start of VMALLOC space
 ARM(	cmp	sp, ip			)	@ SP in vmalloc space?
 THUMB(	cmp	r1, ip			)
 THUMB(	itt	lo			)
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel