[PATCH AUTOSEL 5.15 019/188] ARM: shmobile: rcar-gen2: Add missing of_node_put()

[PATCH AUTOSEL 5.15 019/188] ARM: shmobile: rcar-gen2: Add missing of_node_put()

[Sasha Levin]

From: Wan Jiabing <wanjiabing@vivo.com>

[ Upstream commit 85744f2d938c5f3cfc44cb6533c157469634da93 ]

Fix following coccicheck warning:
./arch/arm/mach-shmobile/regulator-quirk-rcar-gen2.c:156:1-33: Function
for_each_matching_node_and_match should have of_node_put() before break
and goto.

Early exits from for_each_matching_node_and_match() should decrement the
node reference counter.

Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Link: https://lore.kernel.org/r/20211018014503.7598-1-wanjiabing@vivo.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/mach-shmobile/regulator-quirk-rcar-gen2.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/arch/arm/mach-shmobile/regulator-quirk-rcar-gen2.c b/arch/arm/mach-shmobile/regulator-quirk-rcar-gen2.c
index ee949255ced3f..09ef73b99dd86 100644
--- a/arch/arm/mach-shmobile/regulator-quirk-rcar-gen2.c
+++ b/arch/arm/mach-shmobile/regulator-quirk-rcar-gen2.c
@@ -154,8 +154,10 @@ static int __init rcar_gen2_regulator_quirk(void)
 		return -ENODEV;
 
 	for_each_matching_node_and_match(np, rcar_gen2_quirk_match, &id) {
-		if (!of_device_is_available(np))
+		if (!of_device_is_available(np)) {
+			of_node_put(np);
 			break;
+		}
 
 		ret = of_property_read_u32(np, "reg", &addr);
 		if (ret)	/* Skip invalid entry and continue */
@@ -164,6 +166,7 @@ static int __init rcar_gen2_regulator_quirk(void)
 		quirk = kzalloc(sizeof(*quirk), GFP_KERNEL);
 		if (!quirk) {
 			ret = -ENOMEM;
+			of_node_put(np);
 			goto err_mem;
 		}
 
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.15 023/188] usb: dwc3: meson-g12a: fix shared reset control use

[Sasha Levin]

From: Amjad Ouled-Ameur <aouledameur@baylibre.com>

[ Upstream commit 4ce3b45704d5ef46fb4b28083c8aba6716fabf3b ]

reset_control_(de)assert() calls are called on a shared reset line when
reset_control_reset has been used. This is not allowed by the reset
framework.

Use reset_control_rearm() call in suspend() and remove() as a way to state
that the resource is no longer used, hence the shared reset line
may be triggered again by other devices. Use reset_control_rearm() also in
case probe fails after reset() has been called.

reset_control_rearm() keeps use of triggered_count sane in the reset
framework, use of reset_control_reset() on shared reset line should be
balanced with reset_control_rearm().

Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Reported-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20211112162827.128319-3-aouledameur@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/usb/dwc3/dwc3-meson-g12a.c | 17 ++++++++++++-----
 1 file changed, 12 insertions(+), 5 deletions(-)

diff --git a/drivers/usb/dwc3/dwc3-meson-g12a.c b/drivers/usb/dwc3/dwc3-meson-g12a.c
index d0f9b7c296b0d..bd814df3bf8b8 100644
--- a/drivers/usb/dwc3/dwc3-meson-g12a.c
+++ b/drivers/usb/dwc3/dwc3-meson-g12a.c
@@ -755,16 +755,16 @@ static int dwc3_meson_g12a_probe(struct platform_device *pdev)
 
 	ret = dwc3_meson_g12a_get_phys(priv);
 	if (ret)
-		goto err_disable_clks;
+		goto err_rearm;
 
 	ret = priv->drvdata->setup_regmaps(priv, base);
 	if (ret)
-		goto err_disable_clks;
+		goto err_rearm;
 
 	if (priv->vbus) {
 		ret = regulator_enable(priv->vbus);
 		if (ret)
-			goto err_disable_clks;
+			goto err_rearm;
 	}
 
 	/* Get dr_mode */
@@ -825,6 +825,9 @@ static int dwc3_meson_g12a_probe(struct platform_device *pdev)
 	if (priv->vbus)
 		regulator_disable(priv->vbus);
 
+err_rearm:
+	reset_control_rearm(priv->reset);
+
 err_disable_clks:
 	clk_bulk_disable_unprepare(priv->drvdata->num_clks,
 				   priv->drvdata->clks);
@@ -852,6 +855,8 @@ static int dwc3_meson_g12a_remove(struct platform_device *pdev)
 	pm_runtime_put_noidle(dev);
 	pm_runtime_set_suspended(dev);
 
+	reset_control_rearm(priv->reset);
+
 	clk_bulk_disable_unprepare(priv->drvdata->num_clks,
 				   priv->drvdata->clks);
 
@@ -892,7 +897,7 @@ static int __maybe_unused dwc3_meson_g12a_suspend(struct device *dev)
 		phy_exit(priv->phys[i]);
 	}
 
-	reset_control_assert(priv->reset);
+	reset_control_rearm(priv->reset);
 
 	return 0;
 }
@@ -902,7 +907,9 @@ static int __maybe_unused dwc3_meson_g12a_resume(struct device *dev)
 	struct dwc3_meson_g12a *priv = dev_get_drvdata(dev);
 	int i, ret;
 
-	reset_control_deassert(priv->reset);
+	ret = reset_control_reset(priv->reset);
+	if (ret)
+		return ret;
 
 	ret = priv->drvdata->usb_init(priv);
 	if (ret)
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.15 048/188] EDAC/synopsys: Use the quirk for version instead of ddr version

[Sasha Levin]

From: Dinh Nguyen <dinguyen@kernel.org>

[ Upstream commit bd1d6da17c296bd005bfa656952710d256e77dd3 ]

Version 2.40a supports DDR_ECC_INTR_SUPPORT for a quirk, so use that
quirk to determine a call to setup_address_map().

Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lkml.kernel.org/r/20211012190709.1504152-1-dinguyen@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/edac/synopsys_edac.c | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/drivers/edac/synopsys_edac.c b/drivers/edac/synopsys_edac.c
index 7d08627e738b3..a5486d86fdd2f 100644
--- a/drivers/edac/synopsys_edac.c
+++ b/drivers/edac/synopsys_edac.c
@@ -1352,8 +1352,7 @@ static int mc_probe(struct platform_device *pdev)
 		}
 	}
 
-	if (of_device_is_compatible(pdev->dev.of_node,
-				    "xlnx,zynqmp-ddrc-2.40a"))
+	if (priv->p_data->quirks & DDR_ECC_INTR_SUPPORT)
 		setup_address_map(priv);
 #endif
 
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.15 050/188] soc: imx: gpcv2: Synchronously suspend MIX domains

[Sasha Levin]

From: Marek Vasut <marex@denx.de>

[ Upstream commit f756f435f7dd823f2d4bd593ce1bf3168def1308 ]

In case the following power domain sequence happens, iMX8M Mini always hangs:
  gpumix:on -> gpu:on -> gpu:off -> gpu:on
This is likely due to another quirk of the GPC block. This situation can be
prevented by always synchronously powering off both the domain and MIX domain.
Make it so. This turns the aforementioned sequence into:
  gpumix:on -> gpu:on -> gpu:off -> gpumix:off -> gpumix:on -> gpu:on

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Frieder Schrempf <frieder.schrempf@kontron.de>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/soc/imx/gpcv2.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/soc/imx/gpcv2.c b/drivers/soc/imx/gpcv2.c
index 8b7a01773aec2..b4aa28420f2a8 100644
--- a/drivers/soc/imx/gpcv2.c
+++ b/drivers/soc/imx/gpcv2.c
@@ -369,7 +369,7 @@ static int imx_pgc_power_down(struct generic_pm_domain *genpd)
 		}
 	}
 
-	pm_runtime_put(domain->dev);
+	pm_runtime_put_sync_suspend(domain->dev);
 
 	return 0;
 
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.15 051/188] ARM: imx: rename DEBUG_IMX21_IMX27_UART to DEBUG_IMX27_UART

[Sasha Levin]

From: Lukas Bulwahn <lukas.bulwahn@gmail.com>

[ Upstream commit b0100bce4ff82ec1ccd3c1f3d339fd2df6a81784 ]

Since commit 4b563a066611 ("ARM: imx: Remove imx21 support"), the config
DEBUG_IMX21_IMX27_UART is really only debug support for IMX27.

So, rename this option to DEBUG_IMX27_UART and adjust dependencies in
Kconfig and rename the definitions to IMX27 as further clean-up.

This issue was discovered with ./scripts/checkkconfigsymbols.py, which
reported that DEBUG_IMX21_IMX27_UART depends on the non-existing config
SOC_IMX21.

Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/Kconfig.debug            | 14 +++++++-------
 arch/arm/include/debug/imx-uart.h | 18 +++++++++---------
 2 files changed, 16 insertions(+), 16 deletions(-)

diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug
index 98436702e0c7e..644875d73ba15 100644
--- a/arch/arm/Kconfig.debug
+++ b/arch/arm/Kconfig.debug
@@ -410,12 +410,12 @@ choice
 		  Say Y here if you want kernel low-level debugging support
 		  on i.MX25.
 
-	config DEBUG_IMX21_IMX27_UART
-		bool "i.MX21 and i.MX27 Debug UART"
-		depends on SOC_IMX21 || SOC_IMX27
+	config DEBUG_IMX27_UART
+		bool "i.MX27 Debug UART"
+		depends on SOC_IMX27
 		help
 		  Say Y here if you want kernel low-level debugging support
-		  on i.MX21 or i.MX27.
+		  on i.MX27.
 
 	config DEBUG_IMX28_UART
 		bool "i.MX28 Debug UART"
@@ -1481,7 +1481,7 @@ config DEBUG_IMX_UART_PORT
 	int "i.MX Debug UART Port Selection"
 	depends on DEBUG_IMX1_UART || \
 		   DEBUG_IMX25_UART || \
-		   DEBUG_IMX21_IMX27_UART || \
+		   DEBUG_IMX27_UART || \
 		   DEBUG_IMX31_UART || \
 		   DEBUG_IMX35_UART || \
 		   DEBUG_IMX50_UART || \
@@ -1540,12 +1540,12 @@ config DEBUG_LL_INCLUDE
 	default "debug/icedcc.S" if DEBUG_ICEDCC
 	default "debug/imx.S" if DEBUG_IMX1_UART || \
 				 DEBUG_IMX25_UART || \
-				 DEBUG_IMX21_IMX27_UART || \
+				 DEBUG_IMX27_UART || \
 				 DEBUG_IMX31_UART || \
 				 DEBUG_IMX35_UART || \
 				 DEBUG_IMX50_UART || \
 				 DEBUG_IMX51_UART || \
-				 DEBUG_IMX53_UART ||\
+				 DEBUG_IMX53_UART || \
 				 DEBUG_IMX6Q_UART || \
 				 DEBUG_IMX6SL_UART || \
 				 DEBUG_IMX6SX_UART || \
diff --git a/arch/arm/include/debug/imx-uart.h b/arch/arm/include/debug/imx-uart.h
index c8eb83d4b8964..3edbb3c5b42bf 100644
--- a/arch/arm/include/debug/imx-uart.h
+++ b/arch/arm/include/debug/imx-uart.h
@@ -11,13 +11,6 @@
 #define IMX1_UART_BASE_ADDR(n)	IMX1_UART##n##_BASE_ADDR
 #define IMX1_UART_BASE(n)	IMX1_UART_BASE_ADDR(n)
 
-#define IMX21_UART1_BASE_ADDR	0x1000a000
-#define IMX21_UART2_BASE_ADDR	0x1000b000
-#define IMX21_UART3_BASE_ADDR	0x1000c000
-#define IMX21_UART4_BASE_ADDR	0x1000d000
-#define IMX21_UART_BASE_ADDR(n)	IMX21_UART##n##_BASE_ADDR
-#define IMX21_UART_BASE(n)	IMX21_UART_BASE_ADDR(n)
-
 #define IMX25_UART1_BASE_ADDR	0x43f90000
 #define IMX25_UART2_BASE_ADDR	0x43f94000
 #define IMX25_UART3_BASE_ADDR	0x5000c000
@@ -26,6 +19,13 @@
 #define IMX25_UART_BASE_ADDR(n)	IMX25_UART##n##_BASE_ADDR
 #define IMX25_UART_BASE(n)	IMX25_UART_BASE_ADDR(n)
 
+#define IMX27_UART1_BASE_ADDR	0x1000a000
+#define IMX27_UART2_BASE_ADDR	0x1000b000
+#define IMX27_UART3_BASE_ADDR	0x1000c000
+#define IMX27_UART4_BASE_ADDR	0x1000d000
+#define IMX27_UART_BASE_ADDR(n)	IMX27_UART##n##_BASE_ADDR
+#define IMX27_UART_BASE(n)	IMX27_UART_BASE_ADDR(n)
+
 #define IMX31_UART1_BASE_ADDR	0x43f90000
 #define IMX31_UART2_BASE_ADDR	0x43f94000
 #define IMX31_UART3_BASE_ADDR	0x5000c000
@@ -112,10 +112,10 @@
 
 #ifdef CONFIG_DEBUG_IMX1_UART
 #define UART_PADDR	IMX_DEBUG_UART_BASE(IMX1)
-#elif defined(CONFIG_DEBUG_IMX21_IMX27_UART)
-#define UART_PADDR	IMX_DEBUG_UART_BASE(IMX21)
 #elif defined(CONFIG_DEBUG_IMX25_UART)
 #define UART_PADDR	IMX_DEBUG_UART_BASE(IMX25)
+#elif defined(CONFIG_DEBUG_IMX27_UART)
+#define UART_PADDR	IMX_DEBUG_UART_BASE(IMX27)
 #elif defined(CONFIG_DEBUG_IMX31_UART)
 #define UART_PADDR	IMX_DEBUG_UART_BASE(IMX31)
 #elif defined(CONFIG_DEBUG_IMX35_UART)
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.15 054/188] soc: ti: pruss: fix referenced node in error message

[Sasha Levin]

From: Jan Kiszka <jan.kiszka@siemens.com>

[ Upstream commit 8aa35e0bb5eaa42bac415ad0847985daa7b4890c ]

So far, "(null)" is reported for the node that is missing clocks.

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/d6e24953-ea89-fd1c-6e16-7a0142118054@siemens.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/soc/ti/pruss.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/soc/ti/pruss.c b/drivers/soc/ti/pruss.c
index 49da387d77494..b36779309e49b 100644
--- a/drivers/soc/ti/pruss.c
+++ b/drivers/soc/ti/pruss.c
@@ -129,7 +129,7 @@ static int pruss_clk_init(struct pruss *pruss, struct device_node *cfg_node)
 
 	clks_np = of_get_child_by_name(cfg_node, "clocks");
 	if (!clks_np) {
-		dev_err(dev, "%pOF is missing its 'clocks' node\n", clks_np);
+		dev_err(dev, "%pOF is missing its 'clocks' node\n", cfg_node);
 		return -ENODEV;
 	}
 
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.15 058/188] mxser: keep only !tty test in ISR

[Sasha Levin]

From: Jiri Slaby <jslaby@suse.cz>

[ Upstream commit 274ab58dc2b460cc474ffc7ccfcede4b2be1a3f5 ]

The others are superfluous with tty refcounting in place now. And they
are racy in fact:
* tty_port_initialized() reports false for a small moment after
  interrupts are enabled.
* closing is 1 while the port is still alive.

The queues are flushed later during close anyway. So there is no need
for this special handling. Actually, the ISR should not flush the
queues. It should behave as every other driver, just queue the chars
into tty buffer and go on. But this will be changed later. There is
still a lot code depending on having tty in ISR (and not only tty_port).

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-4-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/tty/mxser.c | 5 +----
 1 file changed, 1 insertion(+), 4 deletions(-)

diff --git a/drivers/tty/mxser.c b/drivers/tty/mxser.c
index 1216f3985e18e..da375851af4e6 100644
--- a/drivers/tty/mxser.c
+++ b/drivers/tty/mxser.c
@@ -261,7 +261,6 @@ struct mxser_port {
 	unsigned int xmit_head;
 	unsigned int xmit_tail;
 	unsigned int xmit_cnt;
-	int closing;
 
 	spinlock_t slock;
 };
@@ -923,7 +922,6 @@ static void mxser_close(struct tty_struct *tty, struct file *filp)
 		return;
 	if (tty_port_close_start(port, tty, filp) == 0)
 		return;
-	info->closing = 1;
 	mutex_lock(&port->mutex);
 	mxser_close_port(port);
 	mxser_flush_buffer(tty);
@@ -932,7 +930,6 @@ static void mxser_close(struct tty_struct *tty, struct file *filp)
 	mxser_shutdown_port(port);
 	tty_port_set_initialized(port, 0);
 	mutex_unlock(&port->mutex);
-	info->closing = 0;
 	/* Right now the tty_port set is done outside of the close_end helper
 	   as we don't yet have everyone using refcounts */	
 	tty_port_close_end(port, tty);
@@ -1693,7 +1690,7 @@ static bool mxser_port_isr(struct mxser_port *port)
 
 	iir &= MOXA_MUST_IIR_MASK;
 	tty = tty_port_tty_get(&port->port);
-	if (!tty || port->closing || !tty_port_initialized(&port->port)) {
+	if (!tty) {
 		status = inb(port->ioaddr + UART_LSR);
 		outb(MOXA_MUST_FCR_GDA_MODE_ENABLE | UART_FCR_ENABLE_FIFO |
 				UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT,
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.15 059/188] tty: serial: imx: disable UCR4_OREN in .stop_rx() instead of .shutdown()

[Sasha Levin]

From: Fugang Duan <fugang.duan@nxp.com>

[ Upstream commit 028e083832b06fdeeb290e1e57dc1f6702c4c215 ]

The UCR4_OREN should be disabled before disabling the uart receiver in
.stop_rx() instead of in the .shutdown().

Otherwise, if we have the overrun error during the receiver disable
process, the overrun interrupt will keep trigging until we disable the
OREN interrupt in the .shutdown(), because the ORE status can only be
cleared when read the rx FIFO or reset the controller.  Although the
called time between the receiver disable and OREN disable in .shutdown()
is very short, there is still the risk of endless interrupt during this
short period of time. So here change to disable OREN before the receiver
been disabled in .stop_rx().

Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20211125020349.4980-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/tty/serial/imx.c | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)

diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c
index 51a9f9423b1a6..7820049aba5af 100644
--- a/drivers/tty/serial/imx.c
+++ b/drivers/tty/serial/imx.c
@@ -486,18 +486,21 @@ static void imx_uart_stop_tx(struct uart_port *port)
 static void imx_uart_stop_rx(struct uart_port *port)
 {
 	struct imx_port *sport = (struct imx_port *)port;
-	u32 ucr1, ucr2;
+	u32 ucr1, ucr2, ucr4;
 
 	ucr1 = imx_uart_readl(sport, UCR1);
 	ucr2 = imx_uart_readl(sport, UCR2);
+	ucr4 = imx_uart_readl(sport, UCR4);
 
 	if (sport->dma_is_enabled) {
 		ucr1 &= ~(UCR1_RXDMAEN | UCR1_ATDMAEN);
 	} else {
 		ucr1 &= ~UCR1_RRDYEN;
 		ucr2 &= ~UCR2_ATEN;
+		ucr4 &= ~UCR4_OREN;
 	}
 	imx_uart_writel(sport, ucr1, UCR1);
+	imx_uart_writel(sport, ucr4, UCR4);
 
 	ucr2 &= ~UCR2_RXEN;
 	imx_uart_writel(sport, ucr2, UCR2);
@@ -1544,7 +1547,7 @@ static void imx_uart_shutdown(struct uart_port *port)
 	imx_uart_writel(sport, ucr1, UCR1);
 
 	ucr4 = imx_uart_readl(sport, UCR4);
-	ucr4 &= ~(UCR4_OREN | UCR4_TCEN);
+	ucr4 &= ~UCR4_TCEN;
 	imx_uart_writel(sport, ucr4, UCR4);
 
 	spin_unlock_irqrestore(&sport->port.lock, flags);
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.15 076/188] arm64: dts: ti: j7200-main: Fix 'dtbs_check' serdes_ln_ctrl node

[Sasha Levin]

From: Kishon Vijay Abraham I <kishon@ti.com>

[ Upstream commit 4d3984906397581dc0ccb6a02bf16b6ff82c9192 ]

Fix 'dtbs_check' in serdes_ln_ctrl (serdes-ln-ctrl@4080) node by
changing the node name to mux-controller@4080.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20211126084555.17797-2-kishon@ti.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
index 874cba75e9a5a..7daa280220442 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
@@ -32,7 +32,7 @@ scm_conf: scm-conf@100000 {
 		#size-cells = <1>;
 		ranges = <0x00 0x00 0x00100000 0x1c000>;
 
-		serdes_ln_ctrl: serdes-ln-ctrl@4080 {
+		serdes_ln_ctrl: mux-controller@4080 {
 			compatible = "mmio-mux";
 			#mux-control-cells = <1>;
 			mux-reg-masks = <0x4080 0x3>, <0x4084 0x3>, /* SERDES0 lane0/1 select */
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.15 077/188] arm64: dts: ti: j721e-main: Fix 'dtbs_check' in serdes_ln_ctrl node

[Sasha Levin]

From: Kishon Vijay Abraham I <kishon@ti.com>

[ Upstream commit 3f92a5be6084b77f764a8bbb881ac0d12cb9e863 ]

Fix 'dtbs_check' in serdes_ln_ctrl (mux@4080) node by changing the node
name to mux-controller@4080.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20211126084555.17797-3-kishon@ti.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/ti/k3-j721e-main.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
index 08c8d1b47dcd9..e85c89eebfa31 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
@@ -42,7 +42,7 @@ scm_conf: scm-conf@100000 {
 		#size-cells = <1>;
 		ranges = <0x0 0x0 0x00100000 0x1c000>;
 
-		serdes_ln_ctrl: mux@4080 {
+		serdes_ln_ctrl: mux-controller@4080 {
 			compatible = "mmio-mux";
 			reg = <0x00004080 0x50>;
 			#mux-control-cells = <1>;
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.15 078/188] usb: uhci: add aspeed ast2600 uhci support

[Sasha Levin]

From: Neal Liu <neal_liu@aspeedtech.com>

[ Upstream commit 554abfe2eadec97d12c71d4a69da1518478f69eb ]

Enable ast2600 uhci quirks.

Signed-off-by: Neal Liu <neal_liu@aspeedtech.com>
Link: https://lore.kernel.org/r/20211126100021.2331024-1-neal_liu@aspeedtech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/usb/host/uhci-platform.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/usb/host/uhci-platform.c b/drivers/usb/host/uhci-platform.c
index 70dbd95c3f063..be9e9db7cad10 100644
--- a/drivers/usb/host/uhci-platform.c
+++ b/drivers/usb/host/uhci-platform.c
@@ -113,7 +113,8 @@ static int uhci_hcd_platform_probe(struct platform_device *pdev)
 				num_ports);
 		}
 		if (of_device_is_compatible(np, "aspeed,ast2400-uhci") ||
-		    of_device_is_compatible(np, "aspeed,ast2500-uhci")) {
+		    of_device_is_compatible(np, "aspeed,ast2500-uhci") ||
+		    of_device_is_compatible(np, "aspeed,ast2600-uhci")) {
 			uhci->is_aspeed = 1;
 			dev_info(&pdev->dev,
 				 "Enabled Aspeed implementation workarounds\n");
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.15 098/188] gpio: aspeed: Convert aspeed_gpio.lock to raw_spinlock

[Sasha Levin]

From: Iwona Winiarska <iwona.winiarska@intel.com>

[ Upstream commit 61a7904b6ace99b1bde0d0e867fa3097f5c8cee2 ]

The gpio-aspeed driver implements an irq_chip which need to be invoked
from hardirq context. Since spin_lock() can sleep with PREEMPT_RT, it is
no longer legal to invoke it while interrupts are disabled.
This also causes lockdep to complain about:
[    0.649797] [ BUG: Invalid wait context ]
because aspeed_gpio.lock (spin_lock_t) is taken under irq_desc.lock
(raw_spinlock_t).
Let's use of raw_spinlock_t instead of spinlock_t.

Signed-off-by: Iwona Winiarska <iwona.winiarska@intel.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/gpio/gpio-aspeed.c | 52 +++++++++++++++++++-------------------
 1 file changed, 26 insertions(+), 26 deletions(-)

diff --git a/drivers/gpio/gpio-aspeed.c b/drivers/gpio/gpio-aspeed.c
index 3c8f20c57695f..318a7d95a1a8b 100644
--- a/drivers/gpio/gpio-aspeed.c
+++ b/drivers/gpio/gpio-aspeed.c
@@ -53,7 +53,7 @@ struct aspeed_gpio_config {
 struct aspeed_gpio {
 	struct gpio_chip chip;
 	struct irq_chip irqc;
-	spinlock_t lock;
+	raw_spinlock_t lock;
 	void __iomem *base;
 	int irq;
 	const struct aspeed_gpio_config *config;
@@ -413,14 +413,14 @@ static void aspeed_gpio_set(struct gpio_chip *gc, unsigned int offset,
 	unsigned long flags;
 	bool copro;
 
-	spin_lock_irqsave(&gpio->lock, flags);
+	raw_spin_lock_irqsave(&gpio->lock, flags);
 	copro = aspeed_gpio_copro_request(gpio, offset);
 
 	__aspeed_gpio_set(gc, offset, val);
 
 	if (copro)
 		aspeed_gpio_copro_release(gpio, offset);
-	spin_unlock_irqrestore(&gpio->lock, flags);
+	raw_spin_unlock_irqrestore(&gpio->lock, flags);
 }
 
 static int aspeed_gpio_dir_in(struct gpio_chip *gc, unsigned int offset)
@@ -435,7 +435,7 @@ static int aspeed_gpio_dir_in(struct gpio_chip *gc, unsigned int offset)
 	if (!have_input(gpio, offset))
 		return -ENOTSUPP;
 
-	spin_lock_irqsave(&gpio->lock, flags);
+	raw_spin_lock_irqsave(&gpio->lock, flags);
 
 	reg = ioread32(addr);
 	reg &= ~GPIO_BIT(offset);
@@ -445,7 +445,7 @@ static int aspeed_gpio_dir_in(struct gpio_chip *gc, unsigned int offset)
 	if (copro)
 		aspeed_gpio_copro_release(gpio, offset);
 
-	spin_unlock_irqrestore(&gpio->lock, flags);
+	raw_spin_unlock_irqrestore(&gpio->lock, flags);
 
 	return 0;
 }
@@ -463,7 +463,7 @@ static int aspeed_gpio_dir_out(struct gpio_chip *gc,
 	if (!have_output(gpio, offset))
 		return -ENOTSUPP;
 
-	spin_lock_irqsave(&gpio->lock, flags);
+	raw_spin_lock_irqsave(&gpio->lock, flags);
 
 	reg = ioread32(addr);
 	reg |= GPIO_BIT(offset);
@@ -474,7 +474,7 @@ static int aspeed_gpio_dir_out(struct gpio_chip *gc,
 
 	if (copro)
 		aspeed_gpio_copro_release(gpio, offset);
-	spin_unlock_irqrestore(&gpio->lock, flags);
+	raw_spin_unlock_irqrestore(&gpio->lock, flags);
 
 	return 0;
 }
@@ -492,11 +492,11 @@ static int aspeed_gpio_get_direction(struct gpio_chip *gc, unsigned int offset)
 	if (!have_output(gpio, offset))
 		return GPIO_LINE_DIRECTION_IN;
 
-	spin_lock_irqsave(&gpio->lock, flags);
+	raw_spin_lock_irqsave(&gpio->lock, flags);
 
 	val = ioread32(bank_reg(gpio, bank, reg_dir)) & GPIO_BIT(offset);
 
-	spin_unlock_irqrestore(&gpio->lock, flags);
+	raw_spin_unlock_irqrestore(&gpio->lock, flags);
 
 	return val ? GPIO_LINE_DIRECTION_OUT : GPIO_LINE_DIRECTION_IN;
 }
@@ -539,14 +539,14 @@ static void aspeed_gpio_irq_ack(struct irq_data *d)
 
 	status_addr = bank_reg(gpio, bank, reg_irq_status);
 
-	spin_lock_irqsave(&gpio->lock, flags);
+	raw_spin_lock_irqsave(&gpio->lock, flags);
 	copro = aspeed_gpio_copro_request(gpio, offset);
 
 	iowrite32(bit, status_addr);
 
 	if (copro)
 		aspeed_gpio_copro_release(gpio, offset);
-	spin_unlock_irqrestore(&gpio->lock, flags);
+	raw_spin_unlock_irqrestore(&gpio->lock, flags);
 }
 
 static void aspeed_gpio_irq_set_mask(struct irq_data *d, bool set)
@@ -565,7 +565,7 @@ static void aspeed_gpio_irq_set_mask(struct irq_data *d, bool set)
 
 	addr = bank_reg(gpio, bank, reg_irq_enable);
 
-	spin_lock_irqsave(&gpio->lock, flags);
+	raw_spin_lock_irqsave(&gpio->lock, flags);
 	copro = aspeed_gpio_copro_request(gpio, offset);
 
 	reg = ioread32(addr);
@@ -577,7 +577,7 @@ static void aspeed_gpio_irq_set_mask(struct irq_data *d, bool set)
 
 	if (copro)
 		aspeed_gpio_copro_release(gpio, offset);
-	spin_unlock_irqrestore(&gpio->lock, flags);
+	raw_spin_unlock_irqrestore(&gpio->lock, flags);
 }
 
 static void aspeed_gpio_irq_mask(struct irq_data *d)
@@ -629,7 +629,7 @@ static int aspeed_gpio_set_type(struct irq_data *d, unsigned int type)
 		return -EINVAL;
 	}
 
-	spin_lock_irqsave(&gpio->lock, flags);
+	raw_spin_lock_irqsave(&gpio->lock, flags);
 	copro = aspeed_gpio_copro_request(gpio, offset);
 
 	addr = bank_reg(gpio, bank, reg_irq_type0);
@@ -649,7 +649,7 @@ static int aspeed_gpio_set_type(struct irq_data *d, unsigned int type)
 
 	if (copro)
 		aspeed_gpio_copro_release(gpio, offset);
-	spin_unlock_irqrestore(&gpio->lock, flags);
+	raw_spin_unlock_irqrestore(&gpio->lock, flags);
 
 	irq_set_handler_locked(d, handler);
 
@@ -716,7 +716,7 @@ static int aspeed_gpio_reset_tolerance(struct gpio_chip *chip,
 
 	treg = bank_reg(gpio, to_bank(offset), reg_tolerance);
 
-	spin_lock_irqsave(&gpio->lock, flags);
+	raw_spin_lock_irqsave(&gpio->lock, flags);
 	copro = aspeed_gpio_copro_request(gpio, offset);
 
 	val = readl(treg);
@@ -730,7 +730,7 @@ static int aspeed_gpio_reset_tolerance(struct gpio_chip *chip,
 
 	if (copro)
 		aspeed_gpio_copro_release(gpio, offset);
-	spin_unlock_irqrestore(&gpio->lock, flags);
+	raw_spin_unlock_irqrestore(&gpio->lock, flags);
 
 	return 0;
 }
@@ -856,7 +856,7 @@ static int enable_debounce(struct gpio_chip *chip, unsigned int offset,
 		return rc;
 	}
 
-	spin_lock_irqsave(&gpio->lock, flags);
+	raw_spin_lock_irqsave(&gpio->lock, flags);
 
 	if (timer_allocation_registered(gpio, offset)) {
 		rc = unregister_allocated_timer(gpio, offset);
@@ -916,7 +916,7 @@ static int enable_debounce(struct gpio_chip *chip, unsigned int offset,
 	configure_timer(gpio, offset, i);
 
 out:
-	spin_unlock_irqrestore(&gpio->lock, flags);
+	raw_spin_unlock_irqrestore(&gpio->lock, flags);
 
 	return rc;
 }
@@ -927,13 +927,13 @@ static int disable_debounce(struct gpio_chip *chip, unsigned int offset)
 	unsigned long flags;
 	int rc;
 
-	spin_lock_irqsave(&gpio->lock, flags);
+	raw_spin_lock_irqsave(&gpio->lock, flags);
 
 	rc = unregister_allocated_timer(gpio, offset);
 	if (!rc)
 		configure_timer(gpio, offset, 0);
 
-	spin_unlock_irqrestore(&gpio->lock, flags);
+	raw_spin_unlock_irqrestore(&gpio->lock, flags);
 
 	return rc;
 }
@@ -1015,7 +1015,7 @@ int aspeed_gpio_copro_grab_gpio(struct gpio_desc *desc,
 		return -EINVAL;
 	bindex = offset >> 3;
 
-	spin_lock_irqsave(&gpio->lock, flags);
+	raw_spin_lock_irqsave(&gpio->lock, flags);
 
 	/* Sanity check, this shouldn't happen */
 	if (gpio->cf_copro_bankmap[bindex] == 0xff) {
@@ -1036,7 +1036,7 @@ int aspeed_gpio_copro_grab_gpio(struct gpio_desc *desc,
 	if (bit)
 		*bit = GPIO_OFFSET(offset);
  bail:
-	spin_unlock_irqrestore(&gpio->lock, flags);
+	raw_spin_unlock_irqrestore(&gpio->lock, flags);
 	return rc;
 }
 EXPORT_SYMBOL_GPL(aspeed_gpio_copro_grab_gpio);
@@ -1060,7 +1060,7 @@ int aspeed_gpio_copro_release_gpio(struct gpio_desc *desc)
 		return -EINVAL;
 	bindex = offset >> 3;
 
-	spin_lock_irqsave(&gpio->lock, flags);
+	raw_spin_lock_irqsave(&gpio->lock, flags);
 
 	/* Sanity check, this shouldn't happen */
 	if (gpio->cf_copro_bankmap[bindex] == 0) {
@@ -1074,7 +1074,7 @@ int aspeed_gpio_copro_release_gpio(struct gpio_desc *desc)
 		aspeed_gpio_change_cmd_source(gpio, bank, bindex,
 					      GPIO_CMDSRC_ARM);
  bail:
-	spin_unlock_irqrestore(&gpio->lock, flags);
+	raw_spin_unlock_irqrestore(&gpio->lock, flags);
 	return rc;
 }
 EXPORT_SYMBOL_GPL(aspeed_gpio_copro_release_gpio);
@@ -1148,7 +1148,7 @@ static int __init aspeed_gpio_probe(struct platform_device *pdev)
 	if (IS_ERR(gpio->base))
 		return PTR_ERR(gpio->base);
 
-	spin_lock_init(&gpio->lock);
+	raw_spin_lock_init(&gpio->lock);
 
 	gpio_id = of_match_node(aspeed_gpio_of_table, pdev->dev.of_node);
 	if (!gpio_id)
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.15 099/188] gpio: aspeed-sgpio: Convert aspeed_sgpio.lock to raw_spinlock

[Sasha Levin]

From: Iwona Winiarska <iwona.winiarska@intel.com>

[ Upstream commit ab39d6988dd53f354130438d8afa5596a2440fed ]

The gpio-aspeed-sgpio driver implements an irq_chip which need to be
invoked from hardirq context. Since spin_lock() can sleep with
PREEMPT_RT, it is no longer legal to invoke it while interrupts are
disabled.
This also causes lockdep to complain about:
[   25.919465] [ BUG: Invalid wait context ]
because aspeed_sgpio.lock (spin_lock_t) is taken under irq_desc.lock
(raw_spinlock_t).
Let's use of raw_spinlock_t instead of spinlock_t.

Signed-off-by: Iwona Winiarska <iwona.winiarska@intel.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/gpio/gpio-aspeed-sgpio.c | 32 ++++++++++++++++----------------
 1 file changed, 16 insertions(+), 16 deletions(-)

diff --git a/drivers/gpio/gpio-aspeed-sgpio.c b/drivers/gpio/gpio-aspeed-sgpio.c
index b3a9b8488f11d..454cefbeecf0e 100644
--- a/drivers/gpio/gpio-aspeed-sgpio.c
+++ b/drivers/gpio/gpio-aspeed-sgpio.c
@@ -31,7 +31,7 @@ struct aspeed_sgpio {
 	struct gpio_chip chip;
 	struct irq_chip intc;
 	struct clk *pclk;
-	spinlock_t lock;
+	raw_spinlock_t lock;
 	void __iomem *base;
 	int irq;
 };
@@ -173,12 +173,12 @@ static int aspeed_sgpio_get(struct gpio_chip *gc, unsigned int offset)
 	enum aspeed_sgpio_reg reg;
 	int rc = 0;
 
-	spin_lock_irqsave(&gpio->lock, flags);
+	raw_spin_lock_irqsave(&gpio->lock, flags);
 
 	reg = aspeed_sgpio_is_input(offset) ? reg_val : reg_rdata;
 	rc = !!(ioread32(bank_reg(gpio, bank, reg)) & GPIO_BIT(offset));
 
-	spin_unlock_irqrestore(&gpio->lock, flags);
+	raw_spin_unlock_irqrestore(&gpio->lock, flags);
 
 	return rc;
 }
@@ -215,11 +215,11 @@ static void aspeed_sgpio_set(struct gpio_chip *gc, unsigned int offset, int val)
 	struct aspeed_sgpio *gpio = gpiochip_get_data(gc);
 	unsigned long flags;
 
-	spin_lock_irqsave(&gpio->lock, flags);
+	raw_spin_lock_irqsave(&gpio->lock, flags);
 
 	sgpio_set_value(gc, offset, val);
 
-	spin_unlock_irqrestore(&gpio->lock, flags);
+	raw_spin_unlock_irqrestore(&gpio->lock, flags);
 }
 
 static int aspeed_sgpio_dir_in(struct gpio_chip *gc, unsigned int offset)
@@ -236,9 +236,9 @@ static int aspeed_sgpio_dir_out(struct gpio_chip *gc, unsigned int offset, int v
 	/* No special action is required for setting the direction; we'll
 	 * error-out in sgpio_set_value if this isn't an output GPIO */
 
-	spin_lock_irqsave(&gpio->lock, flags);
+	raw_spin_lock_irqsave(&gpio->lock, flags);
 	rc = sgpio_set_value(gc, offset, val);
-	spin_unlock_irqrestore(&gpio->lock, flags);
+	raw_spin_unlock_irqrestore(&gpio->lock, flags);
 
 	return rc;
 }
@@ -277,11 +277,11 @@ static void aspeed_sgpio_irq_ack(struct irq_data *d)
 
 	status_addr = bank_reg(gpio, bank, reg_irq_status);
 
-	spin_lock_irqsave(&gpio->lock, flags);
+	raw_spin_lock_irqsave(&gpio->lock, flags);
 
 	iowrite32(bit, status_addr);
 
-	spin_unlock_irqrestore(&gpio->lock, flags);
+	raw_spin_unlock_irqrestore(&gpio->lock, flags);
 }
 
 static void aspeed_sgpio_irq_set_mask(struct irq_data *d, bool set)
@@ -296,7 +296,7 @@ static void aspeed_sgpio_irq_set_mask(struct irq_data *d, bool set)
 	irqd_to_aspeed_sgpio_data(d, &gpio, &bank, &bit, &offset);
 	addr = bank_reg(gpio, bank, reg_irq_enable);
 
-	spin_lock_irqsave(&gpio->lock, flags);
+	raw_spin_lock_irqsave(&gpio->lock, flags);
 
 	reg = ioread32(addr);
 	if (set)
@@ -306,7 +306,7 @@ static void aspeed_sgpio_irq_set_mask(struct irq_data *d, bool set)
 
 	iowrite32(reg, addr);
 
-	spin_unlock_irqrestore(&gpio->lock, flags);
+	raw_spin_unlock_irqrestore(&gpio->lock, flags);
 }
 
 static void aspeed_sgpio_irq_mask(struct irq_data *d)
@@ -355,7 +355,7 @@ static int aspeed_sgpio_set_type(struct irq_data *d, unsigned int type)
 		return -EINVAL;
 	}
 
-	spin_lock_irqsave(&gpio->lock, flags);
+	raw_spin_lock_irqsave(&gpio->lock, flags);
 
 	addr = bank_reg(gpio, bank, reg_irq_type0);
 	reg = ioread32(addr);
@@ -372,7 +372,7 @@ static int aspeed_sgpio_set_type(struct irq_data *d, unsigned int type)
 	reg = (reg & ~bit) | type2;
 	iowrite32(reg, addr);
 
-	spin_unlock_irqrestore(&gpio->lock, flags);
+	raw_spin_unlock_irqrestore(&gpio->lock, flags);
 
 	irq_set_handler_locked(d, handler);
 
@@ -467,7 +467,7 @@ static int aspeed_sgpio_reset_tolerance(struct gpio_chip *chip,
 
 	reg = bank_reg(gpio, to_bank(offset), reg_tolerance);
 
-	spin_lock_irqsave(&gpio->lock, flags);
+	raw_spin_lock_irqsave(&gpio->lock, flags);
 
 	val = readl(reg);
 
@@ -478,7 +478,7 @@ static int aspeed_sgpio_reset_tolerance(struct gpio_chip *chip,
 
 	writel(val, reg);
 
-	spin_unlock_irqrestore(&gpio->lock, flags);
+	raw_spin_unlock_irqrestore(&gpio->lock, flags);
 
 	return 0;
 }
@@ -575,7 +575,7 @@ static int __init aspeed_sgpio_probe(struct platform_device *pdev)
 	iowrite32(FIELD_PREP(ASPEED_SGPIO_CLK_DIV_MASK, sgpio_clk_div) | gpio_cnt_regval |
 		  ASPEED_SGPIO_ENABLE, gpio->base + ASPEED_SGPIO_CTRL);
 
-	spin_lock_init(&gpio->lock);
+	raw_spin_lock_init(&gpio->lock);
 
 	gpio->chip.parent = &pdev->dev;
 	gpio->chip.ngpio = nr_gpios * 2;
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.15 115/188] media: rockchip: rkisp1: use device name for debugfs subdir name

[Sasha Levin]

From: Mikhail Rudenko <mike.rudenko@gmail.com>

[ Upstream commit c2611e479f5d9b05108270e1ab423955486b4457 ]

While testing Rockchip RK3399 with both ISPs enabled, a dmesg error
was observed:
```
[   15.559141] debugfs: Directory 'rkisp1' with parent '/' already present!
```

Fix it by using the device name for the debugfs subdirectory name
instead of the driver name, thus preventing name collision.

Link: https://lore.kernel.org/linux-media/20211010175457.438627-1-mike.rudenko@gmail.com
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/platform/rockchip/rkisp1/rkisp1-dev.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/media/platform/rockchip/rkisp1/rkisp1-dev.c b/drivers/media/platform/rockchip/rkisp1/rkisp1-dev.c
index 7474150b94ed3..560f928c37520 100644
--- a/drivers/media/platform/rockchip/rkisp1/rkisp1-dev.c
+++ b/drivers/media/platform/rockchip/rkisp1/rkisp1-dev.c
@@ -426,7 +426,7 @@ static void rkisp1_debug_init(struct rkisp1_device *rkisp1)
 {
 	struct rkisp1_debug *debug = &rkisp1->debug;
 
-	debug->debugfs_dir = debugfs_create_dir(RKISP1_DRIVER_NAME, NULL);
+	debug->debugfs_dir = debugfs_create_dir(dev_name(rkisp1->dev), NULL);
 	debugfs_create_ulong("data_loss", 0444, debug->debugfs_dir,
 			     &debug->data_loss);
 	debugfs_create_ulong("outform_size_err", 0444,  debug->debugfs_dir,
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.15 122/188] arm64: dts: ls1028a-qds: move rtc node to the correct i2c bus

[Sasha Levin]

From: Biwen Li <biwen.li@nxp.com>

[ Upstream commit cbe9d948eadfe352ad45495a7cc5bf20a1b29d90 ]

The i2c rtc is on i2c2 bus not i2c1 bus, so fix it in dts.

Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Li Yang <leoyang.lil@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts | 14 +++++++++-----
 1 file changed, 9 insertions(+), 5 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
index bfd14b64567e4..2f92e62ecafe9 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
@@ -272,11 +272,6 @@ temperature-sensor@4c {
 				vcc-supply = <&sb_3v3>;
 			};
 
-			rtc@51 {
-				compatible = "nxp,pcf2129";
-				reg = <0x51>;
-			};
-
 			eeprom@56 {
 				compatible = "atmel,24c512";
 				reg = <0x56>;
@@ -318,6 +313,15 @@ mux: mux-controller {
 
 };
 
+&i2c1 {
+	status = "okay";
+
+	rtc@51 {
+		compatible = "nxp,pcf2129";
+		reg = <0x51>;
+	};
+};
+
 &enetc_port1 {
 	phy-handle = <&qds_phy1>;
 	phy-connection-type = "rgmii-id";
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.15 130/188] mt76: mt7615: fix possible deadlock while mt7615_register_ext_phy()

[Sasha Levin]

From: Peter Chiu <chui-hao.chiu@mediatek.com>

[ Upstream commit 8c55516de3f9b76b9d9444e7890682ec2efc809f ]

ieee80211_register_hw() is called with rtnl_lock held, and this could be
caused lockdep from a work item that's on a workqueue that is flushed
with the rtnl held.

Move mt7615_register_ext_phy() outside the init_work().

Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/mediatek/mt76/mt7615/pci_init.c | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)

diff --git a/drivers/net/wireless/mediatek/mt76/mt7615/pci_init.c b/drivers/net/wireless/mediatek/mt76/mt7615/pci_init.c
index a2465b49ecd0c..87b4aa52ee0f9 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7615/pci_init.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7615/pci_init.c
@@ -28,8 +28,6 @@ static void mt7615_pci_init_work(struct work_struct *work)
 		return;
 
 	mt7615_init_work(dev);
-	if (dev->dbdc_support)
-		mt7615_register_ext_phy(dev);
 }
 
 static int mt7615_init_hardware(struct mt7615_dev *dev)
@@ -160,6 +158,12 @@ int mt7615_register_device(struct mt7615_dev *dev)
 	mt7615_init_txpower(dev, &dev->mphy.sband_2g.sband);
 	mt7615_init_txpower(dev, &dev->mphy.sband_5g.sband);
 
+	if (dev->dbdc_support) {
+		ret = mt7615_register_ext_phy(dev);
+		if (ret)
+			return ret;
+	}
+
 	return mt7615_init_debugfs(dev);
 }
 
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.15 131/188] mt76: do not pass the received frame with decryption error

[Sasha Levin]

From: Xing Song <xing.song@mediatek.com>

[ Upstream commit dd28dea52ad9376d2b243a8981726646e1f60b1a ]

MAC80211 doesn't care any decryption error in 802.3 path, so received
frame will be dropped if HW tell us that the cipher configuration is not
matched as well as the header has been translated to 802.3. This case only
appears when IEEE80211_FCTL_PROTECTED is 0 and cipher suit is not none in
the corresponding HW entry.

The received frame is only reported to monitor interface if HW decryption
block tell us there is ICV error or CCMP/BIP/WPI MIC error. Note in this
case the reported frame is decrypted 802.11 frame and the payload may be
malformed due to mismatched key.

Signed-off-by: Xing Song <xing.song@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/mediatek/mt76/mt7603/mac.c | 4 ++++
 drivers/net/wireless/mediatek/mt76/mt7615/mac.c | 9 ++++++++-
 drivers/net/wireless/mediatek/mt76/mt7915/mac.c | 9 ++++++++-
 drivers/net/wireless/mediatek/mt76/mt7921/mac.c | 9 ++++++++-
 4 files changed, 28 insertions(+), 3 deletions(-)

diff --git a/drivers/net/wireless/mediatek/mt76/mt7603/mac.c b/drivers/net/wireless/mediatek/mt76/mt7603/mac.c
index 3972c56136a20..65f1f2bb80835 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7603/mac.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7603/mac.c
@@ -525,6 +525,10 @@ mt7603_mac_fill_rx(struct mt7603_dev *dev, struct sk_buff *skb)
 	if (rxd2 & MT_RXD2_NORMAL_TKIP_MIC_ERR)
 		status->flag |= RX_FLAG_MMIC_ERROR;
 
+	/* ICV error or CCMP/BIP/WPI MIC error */
+	if (rxd2 & MT_RXD2_NORMAL_ICV_ERR)
+		status->flag |= RX_FLAG_ONLY_MONITOR;
+
 	if (FIELD_GET(MT_RXD2_NORMAL_SEC_MODE, rxd2) != 0 &&
 	    !(rxd2 & (MT_RXD2_NORMAL_CLM | MT_RXD2_NORMAL_CM))) {
 		status->flag |= RX_FLAG_DECRYPTED;
diff --git a/drivers/net/wireless/mediatek/mt76/mt7615/mac.c b/drivers/net/wireless/mediatek/mt76/mt7615/mac.c
index 5455231f51881..f2704149834a0 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7615/mac.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7615/mac.c
@@ -286,9 +286,16 @@ static int mt7615_mac_fill_rx(struct mt7615_dev *dev, struct sk_buff *skb)
 	if (rxd2 & MT_RXD2_NORMAL_AMSDU_ERR)
 		return -EINVAL;
 
+	hdr_trans = rxd1 & MT_RXD1_NORMAL_HDR_TRANS;
+	if (hdr_trans && (rxd2 & MT_RXD2_NORMAL_CM))
+		return -EINVAL;
+
+	/* ICV error or CCMP/BIP/WPI MIC error */
+	if (rxd2 & MT_RXD2_NORMAL_ICV_ERR)
+		status->flag |= RX_FLAG_ONLY_MONITOR;
+
 	unicast = (rxd1 & MT_RXD1_NORMAL_ADDR_TYPE) == MT_RXD1_NORMAL_U2M;
 	idx = FIELD_GET(MT_RXD2_NORMAL_WLAN_IDX, rxd2);
-	hdr_trans = rxd1 & MT_RXD1_NORMAL_HDR_TRANS;
 	status->wcid = mt7615_rx_get_wcid(dev, idx, unicast);
 
 	if (status->wcid) {
diff --git a/drivers/net/wireless/mediatek/mt76/mt7915/mac.c b/drivers/net/wireless/mediatek/mt76/mt7915/mac.c
index bbc996f86b5c3..ff613d7056119 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7915/mac.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7915/mac.c
@@ -349,9 +349,16 @@ mt7915_mac_fill_rx(struct mt7915_dev *dev, struct sk_buff *skb)
 	if (rxd2 & MT_RXD2_NORMAL_AMSDU_ERR)
 		return -EINVAL;
 
+	hdr_trans = rxd2 & MT_RXD2_NORMAL_HDR_TRANS;
+	if (hdr_trans && (rxd1 & MT_RXD1_NORMAL_CM))
+		return -EINVAL;
+
+	/* ICV error or CCMP/BIP/WPI MIC error */
+	if (rxd1 & MT_RXD1_NORMAL_ICV_ERR)
+		status->flag |= RX_FLAG_ONLY_MONITOR;
+
 	unicast = FIELD_GET(MT_RXD3_NORMAL_ADDR_TYPE, rxd3) == MT_RXD3_NORMAL_U2M;
 	idx = FIELD_GET(MT_RXD1_NORMAL_WLAN_IDX, rxd1);
-	hdr_trans = rxd2 & MT_RXD2_NORMAL_HDR_TRANS;
 	status->wcid = mt7915_rx_get_wcid(dev, idx, unicast);
 
 	if (status->wcid) {
diff --git a/drivers/net/wireless/mediatek/mt76/mt7921/mac.c b/drivers/net/wireless/mediatek/mt76/mt7921/mac.c
index 8a16f3f4d5253..04a288029c98e 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7921/mac.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7921/mac.c
@@ -383,10 +383,17 @@ int mt7921_mac_fill_rx(struct mt7921_dev *dev, struct sk_buff *skb)
 	if (rxd2 & MT_RXD2_NORMAL_AMSDU_ERR)
 		return -EINVAL;
 
+	hdr_trans = rxd2 & MT_RXD2_NORMAL_HDR_TRANS;
+	if (hdr_trans && (rxd1 & MT_RXD1_NORMAL_CM))
+		return -EINVAL;
+
+	/* ICV error or CCMP/BIP/WPI MIC error */
+	if (rxd1 & MT_RXD1_NORMAL_ICV_ERR)
+		status->flag |= RX_FLAG_ONLY_MONITOR;
+
 	chfreq = FIELD_GET(MT_RXD3_NORMAL_CH_FREQ, rxd3);
 	unicast = FIELD_GET(MT_RXD3_NORMAL_ADDR_TYPE, rxd3) == MT_RXD3_NORMAL_U2M;
 	idx = FIELD_GET(MT_RXD1_NORMAL_WLAN_IDX, rxd1);
-	hdr_trans = rxd2 & MT_RXD2_NORMAL_HDR_TRANS;
 	status->wcid = mt7921_rx_get_wcid(dev, idx, unicast);
 
 	if (status->wcid) {
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.15 132/188] mt76: mt7615: improve wmm index allocation

[Sasha Levin]

From: Felix Fietkau <nbd@nbd.name>

[ Upstream commit 70fb028707c8871ef9e56b3ffa3d895e14956cc4 ]

Typically all AP interfaces on a PHY will share the same WMM settings, while
sta/mesh interfaces will usually inherit the settings from a remote device.
In order minimize the likelihood of conflicting WMM settings, make all AP
interfaces share one slot, and all non-AP interfaces another one.

This also fixes running multiple AP interfaces on MT7613, which only has 3
WMM slots.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/mediatek/mt76/mt7615/main.c | 8 +++-----
 1 file changed, 3 insertions(+), 5 deletions(-)

diff --git a/drivers/net/wireless/mediatek/mt76/mt7615/main.c b/drivers/net/wireless/mediatek/mt76/mt7615/main.c
index 51260a669d166..fc266da54fe7b 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7615/main.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7615/main.c
@@ -211,11 +211,9 @@ static int mt7615_add_interface(struct ieee80211_hw *hw,
 	mvif->mt76.omac_idx = idx;
 
 	mvif->mt76.band_idx = ext_phy;
-	if (mt7615_ext_phy(dev))
-		mvif->mt76.wmm_idx = ext_phy * (MT7615_MAX_WMM_SETS / 2) +
-				mvif->mt76.idx % (MT7615_MAX_WMM_SETS / 2);
-	else
-		mvif->mt76.wmm_idx = mvif->mt76.idx % MT7615_MAX_WMM_SETS;
+	mvif->mt76.wmm_idx = vif->type != NL80211_IFTYPE_AP;
+	if (ext_phy)
+		mvif->mt76.wmm_idx += 2;
 
 	dev->mt76.vif_mask |= BIT(mvif->mt76.idx);
 	dev->omac_mask |= BIT_ULL(mvif->mt76.omac_idx);
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.15 157/188] mmc: mtk-sd: Use readl_poll_timeout instead of open-coded polling

[Sasha Levin]

From: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

[ Upstream commit ffaea6ebfe9ce06ebb3a54811a47688f2b0893cd ]

Replace all instances of open-coded while loops for polling registers
with calls to readl_poll_timeout() and, while at it, also fix some
possible infinite loop instances.

Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20211216125748.179602-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/mmc/host/mtk-sd.c | 64 ++++++++++++++++++++++++---------------
 1 file changed, 39 insertions(+), 25 deletions(-)

diff --git a/drivers/mmc/host/mtk-sd.c b/drivers/mmc/host/mtk-sd.c
index 9e6dab7e34242..1ac92015992ed 100644
--- a/drivers/mmc/host/mtk-sd.c
+++ b/drivers/mmc/host/mtk-sd.c
@@ -628,12 +628,11 @@ static void msdc_reset_hw(struct msdc_host *host)
 	u32 val;
 
 	sdr_set_bits(host->base + MSDC_CFG, MSDC_CFG_RST);
-	while (readl(host->base + MSDC_CFG) & MSDC_CFG_RST)
-		cpu_relax();
+	readl_poll_timeout(host->base + MSDC_CFG, val, !(val & MSDC_CFG_RST), 0, 0);
 
 	sdr_set_bits(host->base + MSDC_FIFOCS, MSDC_FIFOCS_CLR);
-	while (readl(host->base + MSDC_FIFOCS) & MSDC_FIFOCS_CLR)
-		cpu_relax();
+	readl_poll_timeout(host->base + MSDC_FIFOCS, val,
+			   !(val & MSDC_FIFOCS_CLR), 0, 0);
 
 	val = readl(host->base + MSDC_INT);
 	writel(val, host->base + MSDC_INT);
@@ -806,8 +805,9 @@ static void msdc_gate_clock(struct msdc_host *host)
 	clk_disable_unprepare(host->h_clk);
 }
 
-static void msdc_ungate_clock(struct msdc_host *host)
+static int msdc_ungate_clock(struct msdc_host *host)
 {
+	u32 val;
 	int ret;
 
 	clk_prepare_enable(host->h_clk);
@@ -817,11 +817,11 @@ static void msdc_ungate_clock(struct msdc_host *host)
 	ret = clk_bulk_prepare_enable(MSDC_NR_CLOCKS, host->bulk_clks);
 	if (ret) {
 		dev_err(host->dev, "Cannot enable pclk/axi/ahb clock gates\n");
-		return;
+		return ret;
 	}
 
-	while (!(readl(host->base + MSDC_CFG) & MSDC_CFG_CKSTB))
-		cpu_relax();
+	return readl_poll_timeout(host->base + MSDC_CFG, val,
+				  (val & MSDC_CFG_CKSTB), 1, 20000);
 }
 
 static void msdc_set_mclk(struct msdc_host *host, unsigned char timing, u32 hz)
@@ -832,6 +832,7 @@ static void msdc_set_mclk(struct msdc_host *host, unsigned char timing, u32 hz)
 	u32 div;
 	u32 sclk;
 	u32 tune_reg = host->dev_comp->pad_tune_reg;
+	u32 val;
 
 	if (!hz) {
 		dev_dbg(host->dev, "set mclk to 0\n");
@@ -912,8 +913,7 @@ static void msdc_set_mclk(struct msdc_host *host, unsigned char timing, u32 hz)
 	else
 		clk_prepare_enable(clk_get_parent(host->src_clk));
 
-	while (!(readl(host->base + MSDC_CFG) & MSDC_CFG_CKSTB))
-		cpu_relax();
+	readl_poll_timeout(host->base + MSDC_CFG, val, (val & MSDC_CFG_CKSTB), 0, 0);
 	sdr_set_bits(host->base + MSDC_CFG, MSDC_CFG_CKPDN);
 	mmc->actual_clock = sclk;
 	host->mclk = hz;
@@ -1223,13 +1223,13 @@ static bool msdc_cmd_done(struct msdc_host *host, int events,
 static inline bool msdc_cmd_is_ready(struct msdc_host *host,
 		struct mmc_request *mrq, struct mmc_command *cmd)
 {
-	/* The max busy time we can endure is 20ms */
-	unsigned long tmo = jiffies + msecs_to_jiffies(20);
+	u32 val;
+	int ret;
 
-	while ((readl(host->base + SDC_STS) & SDC_STS_CMDBUSY) &&
-			time_before(jiffies, tmo))
-		cpu_relax();
-	if (readl(host->base + SDC_STS) & SDC_STS_CMDBUSY) {
+	/* The max busy time we can endure is 20ms */
+	ret = readl_poll_timeout_atomic(host->base + SDC_STS, val,
+					!(val & SDC_STS_CMDBUSY), 1, 20000);
+	if (ret) {
 		dev_err(host->dev, "CMD bus busy detected\n");
 		host->error |= REQ_CMD_BUSY;
 		msdc_cmd_done(host, MSDC_INT_CMDTMO, mrq, cmd);
@@ -1237,12 +1237,10 @@ static inline bool msdc_cmd_is_ready(struct msdc_host *host,
 	}
 
 	if (mmc_resp_type(cmd) == MMC_RSP_R1B || cmd->data) {
-		tmo = jiffies + msecs_to_jiffies(20);
 		/* R1B or with data, should check SDCBUSY */
-		while ((readl(host->base + SDC_STS) & SDC_STS_SDCBUSY) &&
-				time_before(jiffies, tmo))
-			cpu_relax();
-		if (readl(host->base + SDC_STS) & SDC_STS_SDCBUSY) {
+		ret = readl_poll_timeout_atomic(host->base + SDC_STS, val,
+						!(val & SDC_STS_SDCBUSY), 1, 20000);
+		if (ret) {
 			dev_err(host->dev, "Controller busy detected\n");
 			host->error |= REQ_CMD_BUSY;
 			msdc_cmd_done(host, MSDC_INT_CMDTMO, mrq, cmd);
@@ -1367,6 +1365,8 @@ static bool msdc_data_xfer_done(struct msdc_host *host, u32 events,
 	    (MSDC_INT_XFER_COMPL | MSDC_INT_DATCRCERR | MSDC_INT_DATTMO
 	     | MSDC_INT_DMA_BDCSERR | MSDC_INT_DMA_GPDCSERR
 	     | MSDC_INT_DMA_PROTECT);
+	u32 val;
+	int ret;
 
 	spin_lock_irqsave(&host->lock, flags);
 	done = !host->data;
@@ -1383,8 +1383,14 @@ static bool msdc_data_xfer_done(struct msdc_host *host, u32 events,
 				readl(host->base + MSDC_DMA_CFG));
 		sdr_set_field(host->base + MSDC_DMA_CTRL, MSDC_DMA_CTRL_STOP,
 				1);
-		while (readl(host->base + MSDC_DMA_CFG) & MSDC_DMA_CFG_STS)
-			cpu_relax();
+
+		ret = readl_poll_timeout_atomic(host->base + MSDC_DMA_CFG, val,
+						!(val & MSDC_DMA_CFG_STS), 1, 20000);
+		if (ret) {
+			dev_dbg(host->dev, "DMA stop timed out\n");
+			return false;
+		}
+
 		sdr_clr_bits(host->base + MSDC_INTEN, data_ints_mask);
 		dev_dbg(host->dev, "DMA stop\n");
 
@@ -2598,7 +2604,11 @@ static int msdc_drv_probe(struct platform_device *pdev)
 	spin_lock_init(&host->lock);
 
 	platform_set_drvdata(pdev, mmc);
-	msdc_ungate_clock(host);
+	ret = msdc_ungate_clock(host);
+	if (ret) {
+		dev_err(&pdev->dev, "Cannot ungate clocks!\n");
+		goto release_mem;
+	}
 	msdc_init_hw(host);
 
 	if (mmc->caps2 & MMC_CAP2_CQE) {
@@ -2757,8 +2767,12 @@ static int __maybe_unused msdc_runtime_resume(struct device *dev)
 {
 	struct mmc_host *mmc = dev_get_drvdata(dev);
 	struct msdc_host *host = mmc_priv(mmc);
+	int ret;
+
+	ret = msdc_ungate_clock(host);
+	if (ret)
+		return ret;
 
-	msdc_ungate_clock(host);
 	msdc_restore_reg(host);
 	return 0;
 }
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.15 173/188] net: gemini: allow any RGMII interface mode

[Sasha Levin]

From: "Russell King (Oracle)" <rmk+kernel@armlinux.org.uk>

[ Upstream commit 4e4f325a0a55907b14f579e6b1a38c53755e3de2 ]

The four RGMII interface modes take care of the required RGMII delay
configuration at the PHY and should not be limited by the network MAC
driver. Sadly, gemini was only permitting RGMII mode with no delays,
which would require the required delay to be inserted via PCB tracking
or by the MAC.

However, there are designs that require the PHY to add the delay, which
is impossible without Gemini permitting the other three PHY interface
modes. Fix the driver to allow these.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Link: https://lore.kernel.org/r/E1n4mpT-002PLd-Ha@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/cortina/gemini.c | 9 ++++++---
 1 file changed, 6 insertions(+), 3 deletions(-)

diff --git a/drivers/net/ethernet/cortina/gemini.c b/drivers/net/ethernet/cortina/gemini.c
index 6e745ca4c4333..012ca11a38cc1 100644
--- a/drivers/net/ethernet/cortina/gemini.c
+++ b/drivers/net/ethernet/cortina/gemini.c
@@ -305,21 +305,21 @@ static void gmac_speed_set(struct net_device *netdev)
 	switch (phydev->speed) {
 	case 1000:
 		status.bits.speed = GMAC_SPEED_1000;
-		if (phydev->interface == PHY_INTERFACE_MODE_RGMII)
+		if (phy_interface_mode_is_rgmii(phydev->interface))
 			status.bits.mii_rmii = GMAC_PHY_RGMII_1000;
 		netdev_dbg(netdev, "connect %s to RGMII @ 1Gbit\n",
 			   phydev_name(phydev));
 		break;
 	case 100:
 		status.bits.speed = GMAC_SPEED_100;
-		if (phydev->interface == PHY_INTERFACE_MODE_RGMII)
+		if (phy_interface_mode_is_rgmii(phydev->interface))
 			status.bits.mii_rmii = GMAC_PHY_RGMII_100_10;
 		netdev_dbg(netdev, "connect %s to RGMII @ 100 Mbit\n",
 			   phydev_name(phydev));
 		break;
 	case 10:
 		status.bits.speed = GMAC_SPEED_10;
-		if (phydev->interface == PHY_INTERFACE_MODE_RGMII)
+		if (phy_interface_mode_is_rgmii(phydev->interface))
 			status.bits.mii_rmii = GMAC_PHY_RGMII_100_10;
 		netdev_dbg(netdev, "connect %s to RGMII @ 10 Mbit\n",
 			   phydev_name(phydev));
@@ -389,6 +389,9 @@ static int gmac_setup_phy(struct net_device *netdev)
 		status.bits.mii_rmii = GMAC_PHY_GMII;
 		break;
 	case PHY_INTERFACE_MODE_RGMII:
+	case PHY_INTERFACE_MODE_RGMII_ID:
+	case PHY_INTERFACE_MODE_RGMII_TXID:
+	case PHY_INTERFACE_MODE_RGMII_RXID:
 		netdev_dbg(netdev,
 			   "RGMII: set GMAC0 and GMAC1 to MII/RGMII mode\n");
 		status.bits.mii_rmii = GMAC_PHY_RGMII_100_10;
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel