From: Shawn Guo <shawnguo@kernel.org>
To: Li Yang <leoyang.li@nxp.com>
Cc: linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org,
Alex Marginean <alexandru.marginean@nxp.com>,
Ioana Ciornei <ioana.ciornei@nxp.com>,
Dong Aisheng <aisheng.dong@nxp.com>,
Jason Liu <jason.hui.liu@nxp.com>,
Vladimir Oltean <vladimir.oltean@nxp.com>
Subject: Re: [PATCH v3 8/8] arm64: dts: ls1028a-qds: add overlays for various serdes protocols
Date: Wed, 26 Jan 2022 16:33:52 +0800 [thread overview]
Message-ID: <20220126083348.GG4686@dragon> (raw)
In-Reply-To: <20211214093240.23320-9-leoyang.li@nxp.com>
Hi Leo,
On Tue, Dec 14, 2021 at 03:32:40AM -0600, Li Yang wrote:
> From: Alex Marginean <alexandru.marginean@nxp.com>
>
> Add overlays for various serdes protocols on LS1028A QDS board using
> different PHY cards. These should be applied at boot, based on serdes
> configuration. If no overlay is applied, only the RGMII interface on
> the QDS is available in Linux.
>
> Building device tree fragments requires passing the "-@" argument to
> dtc, which increases the base dtb size and might cause some platforms to
> fail to store the new binary. To avoid that, it would be nice to only
> pass "-@" for the platforms where fragments will be used, aka
> LS1028A-QDS. One approach suggested by Rob Herring is used here:
>
> https://lore.kernel.org/patchwork/patch/821645/
>
> Also moved the enet* override nodes in dts file to be in alphabetic order.
>
> Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
> Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
> Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
> Signed-off-by: Jason Liu <jason.hui.liu@nxp.com>
> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
> Signed-off-by: Li Yang <leoyang.li@nxp.com>
> ---
> arch/arm64/boot/dts/freescale/Makefile | 16 +++
> .../dts/freescale/fsl-ls1028a-qds-13bb.dts | 113 ++++++++++++++++++
> .../dts/freescale/fsl-ls1028a-qds-65bb.dts | 108 +++++++++++++++++
> .../dts/freescale/fsl-ls1028a-qds-7777.dts | 82 +++++++++++++
> .../dts/freescale/fsl-ls1028a-qds-85bb.dts | 107 +++++++++++++++++
> .../dts/freescale/fsl-ls1028a-qds-899b.dts | 75 ++++++++++++
> .../dts/freescale/fsl-ls1028a-qds-9999.dts | 79 ++++++++++++
> .../boot/dts/freescale/fsl-ls1028a-qds.dts | 19 ++-
> .../arm64/boot/dts/freescale/fsl-ls1028a.dtsi | 2 +-
> 9 files changed, 595 insertions(+), 6 deletions(-)
> create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-13bb.dts
> create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-65bb.dts
> create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-7777.dts
> create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-85bb.dts
> create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-899b.dts
> create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-9999.dts
>
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index a14a6173b765..f518eb1e1142 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -1,4 +1,14 @@
> # SPDX-License-Identifier: GPL-2.0
> +
> +# required for overlay support
> +DTC_FLAGS_fsl-ls1028a-qds := -@
> +DTC_FLAGS_fsl-ls1028a-qds-13bb := -@
> +DTC_FLAGS_fsl-ls1028a-qds-65bb := -@
> +DTC_FLAGS_fsl-ls1028a-qds-7777 := -@
> +DTC_FLAGS_fsl-ls1028a-qds-85bb := -@
> +DTC_FLAGS_fsl-ls1028a-qds-899b := -@
> +DTC_FLAGS_fsl-ls1028a-qds-9999 := -@
> +
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-frdm.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-frwy.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-oxalis.dtb
> @@ -11,6 +21,12 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-kontron-sl28-var2.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-kontron-sl28-var3-ads2.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-kontron-sl28-var4.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-qds.dtb
> +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-qds-13bb.dtb
> +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-qds-65bb.dtb
> +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-qds-7777.dtb
> +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-qds-85bb.dtb
> +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-qds-899b.dtb
> +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-qds-9999.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-rdb.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1043a-qds.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1043a-rdb.dtb
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-13bb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-13bb.dts
> new file mode 100644
> index 000000000000..f748a2c12a70
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-13bb.dts
> @@ -0,0 +1,113 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Device Tree fragment for LS1028A QDS board, serdes 13bb
> + *
> + * Copyright 2019-2021 NXP
> + *
> + * Requires a LS1028A QDS board with lane B rework.
> + * Requires a SCH-30841 card with lane A of connector rewired to PHY lane C.
> + * Set-up is a SCH-30842 card in slot 1 and SCH-30841 in slot 2.
> + */
> +
> +/dts-v1/;
> +/plugin/;
> +
> +/ {
> + fragment@0 {
> + target = <&mdio_slot1>;
I cannot find this mdio_slot1 node (and mdio_slot2 below) in any upstream
device tree. We are not going to maintain a bunch of overlays which are
only meant to apply on the out-of-tree DTs.
So please either submit those missing device nodes in the base DT, or I
will have to revert the patch.
Shawn
> +
> + __overlay__ {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + slot1_sgmii: ethernet-phy@2 {
> + /* AQR112 */
> + reg = <0x2>;
> + compatible = "ethernet-phy-ieee802.3-c45";
> + };
> + };
> + };
> +
> + fragment@1 {
> + target = <&enetc_port0>;
> +
> + __overlay__ {
> + phy-handle = <&slot1_sgmii>;
> + phy-mode = "usxgmii";
> + managed = "in-band-status";
> + status = "okay";
> + };
> + };
> +
> + fragment@2 {
> + target = <&mdio_slot2>;
> +
> + __overlay__ {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + /* 4 ports on AQR412 */
> + slot2_qxgmii0: ethernet-phy@0 {
> + reg = <0x0>;
> + compatible = "ethernet-phy-ieee802.3-c45";
> + };
> +
> + slot2_qxgmii1: ethernet-phy@1 {
> + reg = <0x1>;
> + compatible = "ethernet-phy-ieee802.3-c45";
> + };
> +
> + slot2_qxgmii2: ethernet-phy@2 {
> + reg = <0x2>;
> + compatible = "ethernet-phy-ieee802.3-c45";
> + };
> +
> + slot2_qxgmii3: ethernet-phy@3 {
> + reg = <0x3>;
> + compatible = "ethernet-phy-ieee802.3-c45";
> + };
> + };
> + };
> +
> + fragment@3 {
> + target = <&mscc_felix_ports>;
> +
> + __overlay__ {
> + port@0 {
> + status = "okay";
> + phy-handle = <&slot2_qxgmii0>;
> + phy-mode = "usxgmii";
> + managed = "in-band-status";
> + };
> +
> + port@1 {
> + status = "okay";
> + phy-handle = <&slot2_qxgmii1>;
> + phy-mode = "usxgmii";
> + managed = "in-band-status";
> + };
> +
> + port@2 {
> + status = "okay";
> + phy-handle = <&slot2_qxgmii2>;
> + phy-mode = "usxgmii";
> + managed = "in-band-status";
> + };
> +
> + port@3 {
> + status = "okay";
> + phy-handle = <&slot2_qxgmii3>;
> + phy-mode = "usxgmii";
> + managed = "in-band-status";
> + };
> + };
> + };
> +
> + fragment@4 {
> + target = <&mscc_felix>;
> +
> + __overlay__ {
> + status = "okay";
> + };
> + };
> +};
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-65bb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-65bb.dts
> new file mode 100644
> index 000000000000..8ffb707a1576
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-65bb.dts
> @@ -0,0 +1,108 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Device Tree fragment for LS1028A QDS board, serdes 69xx
> + *
> + * Copyright 2019-2021 NXP
> + *
> + * Requires a LS1028A QDS board with lane B rework.
> + * Requires a SCH-30842 card in slot 1 and a SCH-28021 card in slot 2.
> + */
> +
> +/dts-v1/;
> +/plugin/;
> +
> +/ {
> + fragment@0 {
> + target = <&mdio_slot1>;
> +
> + __overlay__ {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + slot1_sgmii: ethernet-phy@2 {
> + /* AQR112 */
> + reg = <0x2>;
> + compatible = "ethernet-phy-ieee802.3-c45";
> + };
> + };
> + };
> +
> + fragment@1 {
> + target = <&enetc_port0>;
> +
> + __overlay__ {
> + phy-handle = <&slot1_sgmii>;
> + phy-mode = "2500base-x";
> + managed = "in-band-status";
> + status = "okay";
> + };
> + };
> +
> + fragment@2 {
> + target = <&mdio_slot2>;
> +
> + __overlay__ {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + /* 4 ports on VSC8514 */
> + slot2_qsgmii0: ethernet-phy@8 {
> + reg = <0x8>;
> + };
> +
> + slot2_qsgmii1: ethernet-phy@9 {
> + reg = <0x9>;
> + };
> +
> + slot2_qsgmii2: ethernet-phy@a {
> + reg = <0xa>;
> + };
> +
> + slot2_qsgmii3: ethernet-phy@b {
> + reg = <0xb>;
> + };
> + };
> + };
> +
> + fragment@3 {
> + target = <&mscc_felix_ports>;
> +
> + __overlay__ {
> + port@0 {
> + status = "okay";
> + phy-handle = <&slot2_qsgmii0>;
> + phy-mode = "qsgmii";
> + managed = "in-band-status";
> + };
> +
> + port@1 {
> + status = "okay";
> + phy-handle = <&slot2_qsgmii1>;
> + phy-mode = "qsgmii";
> + managed = "in-band-status";
> + };
> +
> + port@2 {
> + status = "okay";
> + phy-handle = <&slot2_qsgmii2>;
> + phy-mode = "qsgmii";
> + managed = "in-band-status";
> + };
> +
> + port@3 {
> + status = "okay";
> + phy-handle = <&slot2_qsgmii3>;
> + phy-mode = "qsgmii";
> + managed = "in-band-status";
> + };
> + };
> + };
> +
> + fragment@4 {
> + target = <&mscc_felix>;
> +
> + __overlay__ {
> + status = "okay";
> + };
> + };
> +};
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-7777.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-7777.dts
> new file mode 100644
> index 000000000000..eb6a1e674f10
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-7777.dts
> @@ -0,0 +1,82 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Device Tree fragment for LS1028A QDS board, serdes 7777
> + *
> + * Copyright 2019-2021 NXP
> + *
> + * Requires a LS1028A QDS board without lane B rework.
> + * Requires a SCH-30841 card without lane A/C rewire and with a FW with muxing
> + * disabled, plugged in slot 1.
> + */
> +
> +/dts-v1/;
> +/plugin/;
> +
> +/ {
> + fragment@0 {
> + target = <&mdio_slot1>;
> +
> + __overlay__ {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + /* 4 ports on AQR412 */
> + slot1_sxgmii0: ethernet-phy@0 {
> + reg = <0x0>;
> + compatible = "ethernet-phy-ieee802.3-c45";
> + };
> +
> + slot1_sxgmii1: ethernet-phy@1 {
> + reg = <0x1>;
> + compatible = "ethernet-phy-ieee802.3-c45";
> + };
> +
> + slot1_sxgmii2: ethernet-phy@2 {
> + reg = <0x2>;
> + compatible = "ethernet-phy-ieee802.3-c45";
> + };
> +
> + slot1_sxgmii3: ethernet-phy@3 {
> + reg = <0x3>;
> + compatible = "ethernet-phy-ieee802.3-c45";
> + };
> + };
> + };
> +
> + fragment@1 {
> + target = <&mscc_felix_ports>;
> +
> + __overlay__ {
> + port@0 {
> + status = "okay";
> + phy-handle = <&slot1_sxgmii0>;
> + phy-mode = "2500base-x";
> + };
> +
> + port@1 {
> + status = "okay";
> + phy-handle = <&slot1_sxgmii1>;
> + phy-mode = "2500base-x";
> + };
> +
> + port@2 {
> + status = "okay";
> + phy-handle = <&slot1_sxgmii2>;
> + phy-mode = "2500base-x";
> + };
> +
> + port@3 {
> + status = "okay";
> + phy-handle = <&slot1_sxgmii3>;
> + phy-mode = "2500base-x";
> + };
> + };
> + };
> +
> + fragment@2 {
> + target = <&mscc_felix>;
> + __overlay__ {
> + status = "okay";
> + };
> + };
> +};
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-85bb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-85bb.dts
> new file mode 100644
> index 000000000000..8e90c3088ba1
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-85bb.dts
> @@ -0,0 +1,107 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Device Tree fragment for LS1028A QDS board, serdes 85bb
> + *
> + * Copyright 2019-2021 NXP
> + *
> + * Requires a LS1028A QDS board with lane B rework.
> + * Requires a SCH-24801 card in slot 1 and a SCH-28021 card in slot 2.
> + */
> +
> +/dts-v1/;
> +/plugin/;
> +
> +/ {
> + fragment@0 {
> + target = <&mdio_slot1>;
> +
> + __overlay__ {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + slot1_sgmii: ethernet-phy@1c {
> + /* 1st port on VSC8234 */
> + reg = <0x1c>;
> + };
> + };
> + };
> +
> + fragment@1 {
> + target = <&enetc_port0>;
> +
> + __overlay__ {
> + phy-handle = <&slot1_sgmii>;
> + phy-mode = "sgmii";
> + managed = "in-band-status";
> + status = "okay";
> + };
> + };
> +
> + fragment@2 {
> + target = <&mdio_slot2>;
> +
> + __overlay__ {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + /* 4 ports on VSC8514 */
> + slot2_qsgmii0: ethernet-phy@8 {
> + reg = <0x8>;
> + };
> +
> + slot2_qsgmii1: ethernet-phy@9 {
> + reg = <0x9>;
> + };
> +
> + slot2_qsgmii2: ethernet-phy@a {
> + reg = <0xa>;
> + };
> +
> + slot2_qsgmii3: ethernet-phy@b {
> + reg = <0xb>;
> + };
> + };
> + };
> +
> + fragment@3 {
> + target = <&mscc_felix_ports>;
> +
> + __overlay__ {
> + port@0 {
> + status = "okay";
> + phy-handle = <&slot2_qsgmii0>;
> + phy-mode = "qsgmii";
> + managed = "in-band-status";
> + };
> +
> + port@1 {
> + status = "okay";
> + phy-handle = <&slot2_qsgmii1>;
> + phy-mode = "qsgmii";
> + managed = "in-band-status";
> + };
> +
> + port@2 {
> + status = "okay";
> + phy-handle = <&slot2_qsgmii2>;
> + phy-mode = "qsgmii";
> + managed = "in-band-status";
> + };
> +
> + port@3 {
> + status = "okay";
> + phy-handle = <&slot2_qsgmii3>;
> + phy-mode = "qsgmii";
> + managed = "in-band-status";
> + };
> + };
> + };
> +
> + fragment@4 {
> + target = <&mscc_felix>;
> +
> + __overlay__ {
> + status = "okay";
> + };
> + };
> +};
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-899b.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-899b.dts
> new file mode 100644
> index 000000000000..5d0a094e6c44
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-899b.dts
> @@ -0,0 +1,75 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Device Tree fragment for LS1028A QDS board, serdes 85xx
> + *
> + * Copyright 2019-2021 NXP
> + *
> + * Requires a LS1028A QDS board without lane B rework.
> + * Requires a SCH-24801 card in slot 1.
> + */
> +
> +/dts-v1/;
> +/plugin/;
> +
> +/ {
> + fragment@0 {
> + target = <&mdio_slot1>;
> + __overlay__ {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + /* VSC8234 */
> + slot1_sgmii0: ethernet-phy@1c {
> + reg = <0x1c>;
> + };
> +
> + slot1_sgmii1: ethernet-phy@1d {
> + reg = <0x1d>;
> + };
> +
> + slot1_sgmii2: ethernet-phy@1e {
> + reg = <0x1e>;
> + };
> +
> + slot1_sgmii3: ethernet-phy@1f {
> + reg = <0x1f>;
> + };
> + };
> + };
> +
> + fragment@1 {
> + target = <&enetc_port0>;
> + __overlay__ {
> + phy-handle = <&slot1_sgmii0>;
> + phy-mode = "sgmii";
> + managed = "in-band-status";
> + status = "okay";
> + };
> + };
> +
> + fragment@2 {
> + target = <&mscc_felix_ports>;
> + __overlay__ {
> + port@1 {
> + status = "okay";
> + phy-handle = <&slot1_sgmii1>;
> + phy-mode = "sgmii";
> + managed = "in-band-status";
> + };
> +
> + port@2 {
> + status = "okay";
> + phy-handle = <&slot1_sgmii2>;
> + phy-mode = "sgmii";
> + managed = "in-band-status";
> + };
> + };
> + };
> +
> + fragment@3 {
> + target = <&mscc_felix>;
> + __overlay__ {
> + status = "okay";
> + };
> + };
> +};
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-9999.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-9999.dts
> new file mode 100644
> index 000000000000..1ef743c48e84
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-9999.dts
> @@ -0,0 +1,79 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Device Tree fragment for LS1028A QDS board, serdes 85xx
> + *
> + * Copyright 2019-2021 NXP
> + *
> + * Requires a LS1028A QDS board without lane B rework.
> + * Requires a SCH-24801 card in slot 1.
> + */
> +
> +/dts-v1/;
> +/plugin/;
> +
> +/ {
> + fragment@0 {
> + target = <&mdio_slot1>;
> + __overlay__ {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + /* VSC8234 */
> + slot1_sgmii0: ethernet-phy@1c {
> + reg = <0x1c>;
> + };
> +
> + slot1_sgmii1: ethernet-phy@1d {
> + reg = <0x1d>;
> + };
> +
> + slot1_sgmii2: ethernet-phy@1e {
> + reg = <0x1e>;
> + };
> +
> + slot1_sgmii3: ethernet-phy@1f {
> + reg = <0x1f>;
> + };
> + };
> + };
> +
> + fragment@1 {
> + target = <&mscc_felix_ports>;
> + __overlay__ {
> + port@0 {
> + status = "okay";
> + phy-handle = <&slot1_sgmii0>;
> + phy-mode = "sgmii";
> + managed = "in-band-status";
> + };
> +
> + port@1 {
> + status = "okay";
> + phy-handle = <&slot1_sgmii1>;
> + phy-mode = "sgmii";
> + managed = "in-band-status";
> + };
> +
> + port@2 {
> + status = "okay";
> + phy-handle = <&slot1_sgmii2>;
> + phy-mode = "sgmii";
> + managed = "in-band-status";
> + };
> +
> + port@3 {
> + status = "okay";
> + phy-handle = <&slot1_sgmii3>;
> + phy-mode = "sgmii";
> + managed = "in-band-status";
> + };
> + };
> + };
> +
> + fragment@2 {
> + target = <&mscc_felix>;
> + __overlay__ {
> + status = "okay";
> + };
> + };
> +};
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
> index 782853a449cc..177bc1405f0f 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
> @@ -211,6 +211,16 @@ &duart1 {
> status = "okay";
> };
>
> +&enetc_port1 {
> + phy-handle = <&qds_phy1>;
> + phy-mode = "rgmii-id";
> + status = "okay";
> +};
> +
> +&enetc_port2 {
> + status = "okay";
> +};
> +
> &esdhc {
> status = "okay";
> };
> @@ -326,17 +336,16 @@ rtc@51 {
> };
> };
>
> -&enetc_port1 {
> - phy-handle = <&qds_phy1>;
> - phy-mode = "rgmii-id";
> +&lpuart0 {
> status = "okay";
> };
>
> -&lpuart0 {
> +&lpuart1 {
> status = "okay";
> };
>
> -&lpuart1 {
> +&mscc_felix_port4 {
> + ethernet = <&enetc_port2>;
> status = "okay";
> };
>
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
> index 5a7b26a1bad2..5bb8c26e0825 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
> @@ -1115,7 +1115,7 @@ mscc_felix: ethernet-switch@0,5 {
> interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
> status = "disabled";
>
> - ports {
> + mscc_felix_ports: ports {
> #address-cells = <1>;
> #size-cells = <0>;
>
> --
> 2.25.1
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2022-01-26 8:35 UTC|newest]
Thread overview: 23+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-12-14 9:32 [PATCH v3 0/8] ls1028a device tree update Li Yang
2021-12-14 9:32 ` [PATCH v3 1/8] arm64: dts: ls1028a: Add PCIe EP nodes Li Yang
2022-04-13 16:32 ` Vladimir Oltean
2022-04-13 18:03 ` Leo Li
2022-04-13 18:22 ` Vladimir Oltean
2022-04-13 18:38 ` Leo Li
2021-12-14 9:32 ` [PATCH v3 2/8] arm64: dts: ls1028a: add ftm_alarm1 node to be used as wakeup source Li Yang
2021-12-14 9:32 ` [PATCH v3 3/8] arm64: dts: ls1028a: add flextimer based pwm nodes Li Yang
2022-04-13 16:33 ` Vladimir Oltean
2022-04-13 18:07 ` Leo Li
2022-04-13 18:23 ` Vladimir Oltean
2022-04-13 19:10 ` Leo Li
2022-07-28 9:33 ` Michael Walle
2022-08-16 9:04 ` Michael Walle
2022-08-17 20:20 ` Sean Anderson
2021-12-14 9:32 ` [PATCH v3 4/8] arm64: dts: ls1028a-rdb: reorder nodes to be alphabetic Li Yang
2021-12-16 10:01 ` Shawn Guo
2021-12-14 9:32 ` [PATCH v3 5/8] arm64: dts: ls1028a-rdb: enable pwm0 Li Yang
2021-12-14 9:32 ` [PATCH v3 6/8] arm64: dts: ls1028a-qds: move rtc node to the correct i2c bus Li Yang
2021-12-14 9:32 ` [PATCH v3 7/8] arm64: dts: ls1028a-qds: enable lpuart1 Li Yang
2021-12-14 9:32 ` [PATCH v3 8/8] arm64: dts: ls1028a-qds: add overlays for various serdes protocols Li Yang
2022-01-26 8:33 ` Shawn Guo [this message]
2022-01-26 8:55 ` Leo Li
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20220126083348.GG4686@dragon \
--to=shawnguo@kernel.org \
--cc=aisheng.dong@nxp.com \
--cc=alexandru.marginean@nxp.com \
--cc=ioana.ciornei@nxp.com \
--cc=jason.hui.liu@nxp.com \
--cc=leoyang.li@nxp.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=vladimir.oltean@nxp.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).