[RFC PATCH v3 0/4] Fix and improve gpmi nand on mx28

[RFC PATCH v3 0/4] Fix and improve gpmi nand on mx28

[Dario Binacchi]

Starting from [1], the series fixes the timings setting of the gpmi
controller for the mx28 architecture, also adding support for fast
edo mode timings. The whole series has been heavily tested with the
mtd kernel test modules, and with repeated write cycles on nand.

[1] https://lore.kernel.org/r/20210702065350.209646-5-ebiggers@kernel.org

Changes in v3:
- Remove the "mtd: rawnand: gpmi: use a table to get EDO mode setup" patch.
- Simplify the validation logic (suggested by Sascha Hauer <sha@pengutronix.de>).

Changes in v2:
- Reparent by device tree instead of code (drivers/clk/mxs/clk-imx28.c).
  Suggested by Stephen Boyd.
- Improve the commit description.
- give examples of frequencies on my setup.
- Fix commit description.
- Add an example to the commit description to better understand the
  problem solved by the patch.
- Split the patch.
- Improve the commit message.
- Move the patch to the end of the series.

Dario Binacchi (4):
  ARM: dts: imx28: reparent gpmi clock to ref_gpmi
  mtd: rawnand: gpmi: fix controller timings setting
  mtd: rawnand: gpmi: validate controller clock rate
  mtd: rawnand: gpmi: support fast edo timings for mx28

 arch/arm/boot/dts/imx28.dtsi               |  2 ++
 drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c | 27 ++++++++++++++++++----
 2 files changed, 24 insertions(+), 5 deletions(-)

-- 
2.32.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[RFC PATCH v3 1/4] ARM: dts: imx28: reparent gpmi clock to ref_gpmi

[Dario Binacchi]

Since ref_gpmi is sourced from pll0 (480MHz), It allows the GPMI
controller to manage High-Speed ​​NAND Timing (edo mode 3,4 and 5).

Co-developed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>


---

(no changes since v2)

Changes in v2:
- Reparent by device tree instead of code (drivers/clk/mxs/clk-imx28.c).
  Suggested by Stephen Boyd.

 arch/arm/boot/dts/imx28.dtsi | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/imx28.dtsi
index 84d0176d5193..130b4145af82 100644
--- a/arch/arm/boot/dts/imx28.dtsi
+++ b/arch/arm/boot/dts/imx28.dtsi
@@ -110,6 +110,8 @@ gpmi: nand-controller@8000c000 {
 				interrupt-names = "bch";
 				clocks = <&clks 50>;
 				clock-names = "gpmi_io";
+				assigned-clocks = <&clks 13>;
+				assigned-clock-parents = <&clks 10>;
 				dmas = <&dma_apbh 4>;
 				dma-names = "rx-tx";
 				status = "disabled";
-- 
2.32.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [RFC PATCH v3 1/4] ARM: dts: imx28: reparent gpmi clock to ref_gpmi

[Shawn Guo]

On Mon, Jan 17, 2022 at 05:17:52PM +0100, Dario Binacchi wrote:
> Since ref_gpmi is sourced from pll0 (480MHz), It allows the GPMI
> controller to manage High-Speed ​​NAND Timing (edo mode 3,4 and 5).
> 
> Co-developed-by: Michael Trimarchi <michael@amarulasolutions.com>
> Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
> Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>

Applied, thanks!

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [RFC PATCH v3 0/4] Fix and improve gpmi nand on mx28

[Sascha Hauer]

On Mon, Jan 17, 2022 at 05:17:51PM +0100, Dario Binacchi wrote:
> Starting from [1], the series fixes the timings setting of the gpmi
> controller for the mx28 architecture, also adding support for fast
> edo mode timings. The whole series has been heavily tested with the
> mtd kernel test modules, and with repeated write cycles on nand.
> 
> [1] https://lore.kernel.org/r/20210702065350.209646-5-ebiggers@kernel.org
> 
> Changes in v3:
> - Remove the "mtd: rawnand: gpmi: use a table to get EDO mode setup" patch.
> - Simplify the validation logic (suggested by Sascha Hauer <sha@pengutronix.de>).

Thanks Dario. I gave it a test on a custom i.MX28 board and it works as
expected.

For the series:

Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>

Sascha

-- 
Pengutronix e.K.                           |                             |
Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel