From: Felix Fietkau <nbd@nbd.name>
To: Michael Turquette <mturquette@baylibre.com>,
Stephen Boyd <sboyd@kernel.org>
Cc: soc@kernel.org, linux-mediatek@lists.infradead.org,
linux-arm-kernel@lists.infradead.org, john@phrozen.org,
linux-kernel@vger.kernel.org, linux-clk@vger.kernel.org
Subject: [PATCH v9 06/13] clk: en7523: Add clock driver for Airoha EN7523 SoC
Date: Sun, 30 Jan 2022 15:51:09 +0100 [thread overview]
Message-ID: <20220130145116.88406-7-nbd@nbd.name> (raw)
In-Reply-To: <20220130145116.88406-1-nbd@nbd.name>
This driver only registers fixed rate clocks, since the clocks are fully
initialized by the boot loader and should not be changed later, according
to Airoha.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
---
drivers/clk/Kconfig | 9 +
drivers/clk/Makefile | 1 +
drivers/clk/clk-en7523.c | 350 +++++++++++++++++++++++++++++++++++++++
3 files changed, 360 insertions(+)
create mode 100644 drivers/clk/clk-en7523.c
diff --git a/drivers/clk/Kconfig b/drivers/clk/Kconfig
index c91931c94888..4614d6452fb7 100644
--- a/drivers/clk/Kconfig
+++ b/drivers/clk/Kconfig
@@ -192,6 +192,15 @@ config COMMON_CLK_CS2000_CP
help
If you say yes here you get support for the CS2000 clock multiplier.
+config COMMON_CLK_EN7523
+ bool "Clock driver for Airoha EN7523 SoC system clocks"
+ depends on OF
+ depends on ARCH_AIROHA || COMPILE_TEST
+ default ARCH_AIROHA
+ help
+ This driver provides the fixed clocks and gates present on Airoha
+ ARM silicon.
+
config COMMON_CLK_FSL_FLEXSPI
tristate "Clock driver for FlexSPI on Layerscape SoCs"
depends on ARCH_LAYERSCAPE || COMPILE_TEST
diff --git a/drivers/clk/Makefile b/drivers/clk/Makefile
index a9bb2478fbdd..da1e2ac2dfc1 100644
--- a/drivers/clk/Makefile
+++ b/drivers/clk/Makefile
@@ -27,6 +27,7 @@ obj-$(CONFIG_COMMON_CLK_CDCE925) += clk-cdce925.o
obj-$(CONFIG_ARCH_CLPS711X) += clk-clps711x.o
obj-$(CONFIG_COMMON_CLK_CS2000_CP) += clk-cs2000-cp.o
obj-$(CONFIG_ARCH_SPARX5) += clk-sparx5.o
+obj-$(CONFIG_COMMON_CLK_EN7523) += clk-en7523.o
obj-$(CONFIG_COMMON_CLK_FIXED_MMIO) += clk-fixed-mmio.o
obj-$(CONFIG_COMMON_CLK_FSL_FLEXSPI) += clk-fsl-flexspi.o
obj-$(CONFIG_COMMON_CLK_FSL_SAI) += clk-fsl-sai.o
diff --git a/drivers/clk/clk-en7523.c b/drivers/clk/clk-en7523.c
new file mode 100644
index 000000000000..137e13520ad9
--- /dev/null
+++ b/drivers/clk/clk-en7523.c
@@ -0,0 +1,350 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include <linux/delay.h>
+#include <linux/clk-provider.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <dt-bindings/clock/en7523-clk.h>
+
+#define REG_PCI_CONTROL 0x88
+#define REG_PCI_CONTROL_PERSTOUT BIT(29)
+#define REG_PCI_CONTROL_PERSTOUT1 BIT(26)
+#define REG_PCI_CONTROL_REFCLK_EN1 BIT(22)
+#define REG_GSW_CLK_DIV_SEL 0x1b4
+#define REG_EMI_CLK_DIV_SEL 0x1b8
+#define REG_BUS_CLK_DIV_SEL 0x1bc
+#define REG_SPI_CLK_DIV_SEL 0x1c4
+#define REG_SPI_CLK_FREQ_SEL 0x1c8
+#define REG_NPU_CLK_DIV_SEL 0x1fc
+#define REG_CRYPTO_CLKSRC 0x200
+#define REG_RESET_CONTROL 0x834
+#define REG_RESET_CONTROL_PCIEHB BIT(29)
+#define REG_RESET_CONTROL_PCIE1 BIT(27)
+#define REG_RESET_CONTROL_PCIE2 BIT(26)
+
+struct en_clk_desc {
+ int id;
+ const char *name;
+ u32 base_reg;
+ u32 base_bits;
+ u32 base_shift;
+ union {
+ const u32 *base_values;
+ u32 base_value;
+ };
+ int n_base_values;
+
+ u32 div_reg;
+ u32 div_bits;
+ u32 div_shift;
+ u32 div_val0;
+ u32 div_step;
+};
+
+struct en_clk_gate {
+ void __iomem *base;
+ struct clk_hw hw;
+};
+
+static const u32 gsw_base[] = { 400000000, 500000000 };
+static const u32 emi_base[] = { 333000000, 400000000 };
+static const u32 bus_base[] = { 500000000, 540000000 };
+static const u32 slic_base[] = { 100000000, 3125000 };
+static const u32 npu_base[] = { 333000000, 400000000, 500000000 };
+
+static const struct en_clk_desc en7523_base_clks[] = {
+ {
+ .id = EN7523_CLK_GSW,
+ .name = "gsw",
+
+ .base_reg = REG_GSW_CLK_DIV_SEL,
+ .base_bits = 1,
+ .base_shift = 8,
+ .base_values = gsw_base,
+ .n_base_values = ARRAY_SIZE(gsw_base),
+
+ .div_bits = 3,
+ .div_shift = 0,
+ .div_step = 1,
+ }, {
+ .id = EN7523_CLK_EMI,
+ .name = "emi",
+
+ .base_reg = REG_EMI_CLK_DIV_SEL,
+ .base_bits = 1,
+ .base_shift = 8,
+ .base_values = emi_base,
+ .n_base_values = ARRAY_SIZE(emi_base),
+
+ .div_bits = 3,
+ .div_shift = 0,
+ .div_step = 1,
+ }, {
+ .id = EN7523_CLK_BUS,
+ .name = "bus",
+
+ .base_reg = REG_BUS_CLK_DIV_SEL,
+ .base_bits = 1,
+ .base_shift = 8,
+ .base_values = bus_base,
+ .n_base_values = ARRAY_SIZE(bus_base),
+
+ .div_bits = 3,
+ .div_shift = 0,
+ .div_step = 1,
+ }, {
+ .id = EN7523_CLK_SLIC,
+ .name = "slic",
+
+ .base_reg = REG_SPI_CLK_FREQ_SEL,
+ .base_bits = 1,
+ .base_shift = 0,
+ .base_values = slic_base,
+ .n_base_values = ARRAY_SIZE(slic_base),
+
+ .div_reg = REG_SPI_CLK_DIV_SEL,
+ .div_bits = 5,
+ .div_shift = 24,
+ .div_val0 = 20,
+ .div_step = 2,
+ }, {
+ .id = EN7523_CLK_SPI,
+ .name = "spi",
+
+ .base_reg = REG_SPI_CLK_DIV_SEL,
+
+ .base_value = 400000000,
+
+ .div_bits = 5,
+ .div_shift = 8,
+ .div_val0 = 40,
+ .div_step = 2,
+ }, {
+ .id = EN7523_CLK_NPU,
+ .name = "npu",
+
+ .base_reg = REG_NPU_CLK_DIV_SEL,
+ .base_bits = 2,
+ .base_shift = 8,
+ .base_values = npu_base,
+ .n_base_values = ARRAY_SIZE(npu_base),
+
+ .div_bits = 3,
+ .div_shift = 0,
+ .div_step = 1,
+ }, {
+ .id = EN7523_CLK_CRYPTO,
+ .name = "crypto",
+
+ .base_reg = REG_CRYPTO_CLKSRC,
+ .base_bits = 1,
+ .base_shift = 8,
+ .base_values = emi_base,
+ .n_base_values = ARRAY_SIZE(emi_base),
+ }
+};
+
+static const struct of_device_id of_match_clk_en7523[] = {
+ { .compatible = "airoha,en7523-scu", },
+ { /* sentinel */ }
+};
+
+static u32 en7523_get_base_rate(void __iomem *base, int i)
+{
+ const struct en_clk_desc *desc = &en7523_base_clks[i];
+ u32 val;
+
+ if (!desc->base_bits)
+ return desc->base_value;
+
+ val = readl(base + desc->base_reg);
+ val >>= desc->base_shift;
+ val &= (1 << desc->base_bits) - 1;
+
+ if (val >= desc->n_base_values)
+ return 0;
+
+ return desc->base_values[val];
+}
+
+static u32 en7523_get_div(void __iomem *base, int i)
+{
+ const struct en_clk_desc *desc = &en7523_base_clks[i];
+ u32 reg, val;
+
+ if (!desc->div_bits)
+ return 1;
+
+ reg = desc->div_reg ? desc->div_reg : desc->base_reg;
+ val = readl(base + reg);
+ val >>= desc->div_shift;
+ val &= (1 << desc->div_bits) - 1;
+
+ if (!val && desc->div_val0)
+ return desc->div_val0;
+
+ return (val + 1) * desc->div_step;
+}
+
+static int en7523_pci_is_enabled(struct clk_hw *hw)
+{
+ struct en_clk_gate *cg = container_of(hw, struct en_clk_gate, hw);
+
+ return !!(readl(cg->base + REG_PCI_CONTROL) & REG_PCI_CONTROL_REFCLK_EN1);
+}
+
+static int en7523_pci_prepare(struct clk_hw *hw)
+{
+ struct en_clk_gate *cg = container_of(hw, struct en_clk_gate, hw);
+ void __iomem *np_base = cg->base;
+ u32 val, mask;
+
+ /* Need to pull device low before reset */
+ val = readl(np_base + REG_PCI_CONTROL);
+ val &= ~(REG_PCI_CONTROL_PERSTOUT1 | REG_PCI_CONTROL_PERSTOUT);
+ writel(val, np_base + REG_PCI_CONTROL);
+ usleep_range(1000, 2000);
+
+ /* Enable PCIe port 1 */
+ val |= REG_PCI_CONTROL_REFCLK_EN1;
+ writel(val, np_base + REG_PCI_CONTROL);
+ usleep_range(1000, 2000);
+
+ /* Reset to default */
+ val = readl(np_base + REG_RESET_CONTROL);
+ mask = REG_RESET_CONTROL_PCIE1 | REG_RESET_CONTROL_PCIE2 |
+ REG_RESET_CONTROL_PCIEHB;
+ writel(val & ~mask, np_base + REG_RESET_CONTROL);
+ usleep_range(1000, 2000);
+ writel(val | mask, np_base + REG_RESET_CONTROL);
+ msleep(100);
+ writel(val & ~mask, np_base + REG_RESET_CONTROL);
+ usleep_range(5000, 10000);
+
+ /* Release device */
+ mask = REG_PCI_CONTROL_PERSTOUT1 | REG_PCI_CONTROL_PERSTOUT;
+ val = readl(np_base + REG_PCI_CONTROL);
+ writel(val & ~mask, np_base + REG_PCI_CONTROL);
+ usleep_range(1000, 2000);
+ writel(val | mask, np_base + REG_PCI_CONTROL);
+ msleep(250);
+
+ return 0;
+}
+
+static void en7523_pci_unprepare(struct clk_hw *hw)
+{
+ struct en_clk_gate *cg = container_of(hw, struct en_clk_gate, hw);
+ void __iomem *np_base = cg->base;
+ u32 val;
+
+ val = readl(np_base + REG_PCI_CONTROL);
+ val &= ~REG_PCI_CONTROL_REFCLK_EN1;
+ writel(val, np_base + REG_PCI_CONTROL);
+}
+
+static struct clk_hw *en7523_register_pcie_clk(struct device *dev,
+ void __iomem *np_base)
+{
+ static const struct clk_ops pcie_gate_ops = {
+ .is_enabled = en7523_pci_is_enabled,
+ .prepare = en7523_pci_prepare,
+ .unprepare = en7523_pci_unprepare,
+ };
+ struct clk_init_data init = {
+ .name = "pcie",
+ .ops = &pcie_gate_ops,
+ };
+ struct en_clk_gate *cg;
+
+ cg = devm_kzalloc(dev, sizeof(*cg), GFP_KERNEL);
+ if (!cg)
+ return NULL;
+
+ cg->base = np_base;
+ cg->hw.init = &init;
+ en7523_pci_unprepare(&cg->hw);
+
+ if (clk_hw_register(NULL, &cg->hw))
+ return NULL;
+
+ return &cg->hw;
+}
+
+static void en7523_register_clocks(struct device *dev, struct clk_hw_onecell_data *clk_data,
+ void __iomem *base, void __iomem *np_base)
+{
+ struct clk_hw *hw;
+ u32 rate;
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(en7523_base_clks); i++) {
+ const struct en_clk_desc *desc = &en7523_base_clks[i];
+
+ rate = en7523_get_base_rate(base, i);
+ rate /= en7523_get_div(base, i);
+
+ hw = clk_hw_register_fixed_rate(dev, desc->name, NULL, 0, rate);
+ if (IS_ERR(hw)) {
+ pr_err("Failed to register clk %s: %ld\n",
+ desc->name, PTR_ERR(hw));
+ continue;
+ }
+
+ clk_data->hws[desc->id] = hw;
+ }
+
+ hw = en7523_register_pcie_clk(dev, np_base);
+ clk_data->hws[EN7523_CLK_PCIE] = hw;
+
+ clk_data->num = EN7523_NUM_CLOCKS;
+}
+
+static int en7523_clk_probe(struct platform_device *pdev)
+{
+ struct device_node *node = pdev->dev.of_node;
+ struct clk_hw_onecell_data *clk_data;
+ void __iomem *base, *np_base;
+ int r;
+
+ base = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(base))
+ return PTR_ERR(base);
+
+ np_base = devm_platform_ioremap_resource(pdev, 1);
+ if (IS_ERR(base))
+ return PTR_ERR(np_base);
+
+ clk_data = devm_kzalloc(&pdev->dev,
+ struct_size(clk_data, hws, EN7523_NUM_CLOCKS),
+ GFP_KERNEL);
+ if (!clk_data)
+ return -ENOMEM;
+
+ en7523_register_clocks(&pdev->dev, clk_data, base, np_base);
+
+ r = of_clk_add_hw_provider(node, of_clk_hw_onecell_get, clk_data);
+ if (r)
+ dev_err(&pdev->dev,
+ "could not register clock provider: %s: %d\n",
+ pdev->name, r);
+
+ return r;
+}
+
+static struct platform_driver clk_en7523_drv = {
+ .probe = en7523_clk_probe,
+ .driver = {
+ .name = "clk-en7523",
+ .of_match_table = of_match_clk_en7523,
+ },
+};
+
+static int __init clk_en7523_init(void)
+{
+ return platform_driver_register(&clk_en7523_drv);
+}
+
+arch_initcall(clk_en7523_init);
--
2.32.0 (Apple Git-132)
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2022-01-30 14:54 UTC|newest]
Thread overview: 23+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-01-30 14:51 [PATCH v9 00/13] Add support for Airoha EN7523 SoC Felix Fietkau
2022-01-30 14:51 ` [PATCH v9 01/13] dt-bindings: Add vendor prefix for Airoha Felix Fietkau
2022-01-30 14:51 ` [PATCH v9 02/13] dt-bindings: arm: airoha: Add binding for EN7523 SoC and EVB Felix Fietkau
2022-01-30 14:51 ` [PATCH v9 03/13] ARM: Add basic support for Airoha EN7523 SoC Felix Fietkau
2022-01-31 10:51 ` Luka Perkov
2022-01-31 12:57 ` Felix Fietkau
2022-01-31 13:00 ` Robert Marko
2022-01-31 13:12 ` John Crispin
2022-01-30 14:51 ` [PATCH v9 04/13] ARM: multi_v7_defconfig: Add " Felix Fietkau
2022-01-30 14:51 ` [PATCH v9 05/13] dt-bindings: Add en7523-scu device tree binding documentation Felix Fietkau
2022-01-30 14:51 ` Felix Fietkau [this message]
2022-03-11 0:47 ` [PATCH v9 06/13] clk: en7523: Add clock driver for Airoha EN7523 SoC Stephen Boyd
2022-01-30 14:51 ` [PATCH v9 07/13] ARM: dts: add clock support for Airoha EN7523 Felix Fietkau
2022-01-30 14:51 ` [PATCH v9 08/13] dt-bindings: PCI: Add support for Airoha EN7532 Felix Fietkau
2022-01-30 14:51 ` [PATCH v9 09/13] PCI: mediatek: Allow building for ARCH_AIROHA Felix Fietkau
2022-01-30 14:51 ` [PATCH v9 10/13] ARM: dts: Add PCIe support for Airoha EN7523 Felix Fietkau
2022-01-30 14:51 ` [PATCH v9 11/13] dt-bindings: arm: airoha: Add binding for Airoha GPIO controller Felix Fietkau
2022-02-02 9:16 ` Bartosz Golaszewski
2022-01-30 14:51 ` [PATCH v9 12/13] gpio: Add support for Airoha EN7523 " Felix Fietkau
2022-01-31 11:13 ` Linus Walleij
2022-02-02 9:17 ` Bartosz Golaszewski
2022-01-30 14:51 ` [PATCH v9 13/13] ARM: dts: add GPIO support for Airoha EN7523 Felix Fietkau
2022-03-01 8:08 ` [PATCH v9 00/13] Add support for Airoha EN7523 SoC Matthias Brugger
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20220130145116.88406-7-nbd@nbd.name \
--to=nbd@nbd.name \
--cc=john@phrozen.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mediatek@lists.infradead.org \
--cc=mturquette@baylibre.com \
--cc=sboyd@kernel.org \
--cc=soc@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).