Re: [PATCH v7 7/8] PCI: imx6: Disable enabled clocks and regulators after link is down

From: Bjorn Helgaas <helgaas@kernel.org>
To: Richard Zhu <hongxing.zhu@nxp.com>
Cc: l.stach@pengutronix.de, bhelgaas@google.com, broonie@kernel.org,
	lorenzo.pieralisi@arm.com, jingoohan1@gmail.com,
	festevam@gmail.com, francesco.dolcini@toradex.com,
	linux-pci@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
	linux-kernel@vger.kernel.org, kernel@pengutronix.de,
	linux-imx@nxp.com
Subject: Re: [PATCH v7 7/8] PCI: imx6: Disable enabled clocks and regulators after link is down
Date: Wed, 23 Feb 2022 11:50:16 -0600	[thread overview]
Message-ID: <20220223175016.GA140091@bhelgaas> (raw)
In-Reply-To: <1644992463-14467-8-git-send-email-hongxing.zhu@nxp.com>

In subject,

s/Disable enabled clocks/Disable clocks/

On Wed, Feb 16, 2022 at 02:21:02PM +0800, Richard Zhu wrote:
> Since i.MX PCIe doesn't support the hot-plug, and to save power
> consumption as much as possible. Return error and disable the enabled
> clocks and regulators when link is down,.

Maybe:

  Since i.MX PCIe doesn't support hot-plug, reduce power consumption
  as much as possible by disabling clocks and regulators and returning
  error when the link is down.

> Add a new host_exit() callback for i.MX PCIe driver to disable the
> enabled clocks, regulators and so on in the error handling after
> host_init is finished.
> 
> Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
> ---
>  drivers/pci/controller/dwc/pci-imx6.c | 30 ++++++++++++++++++++++++---
>  1 file changed, 27 insertions(+), 3 deletions(-)
> 
> diff --git a/drivers/pci/controller/dwc/pci-imx6.c b/drivers/pci/controller/dwc/pci-imx6.c
> index 242d8ef73c1e..fe671e88ec93 100644
> --- a/drivers/pci/controller/dwc/pci-imx6.c
> +++ b/drivers/pci/controller/dwc/pci-imx6.c
> @@ -848,7 +848,9 @@ static int imx6_pcie_start_link(struct dw_pcie *pci)
>  	/* Start LTSSM. */
>  	imx6_pcie_ltssm_enable(dev);
>  
> -	dw_pcie_wait_for_link(pci);
> +	ret = dw_pcie_wait_for_link(pci);
> +	if (ret)
> +		goto err_reset_phy;

These labels look wrong now, since you no longer reset the PHY at
err_reset_phy.

>  	if (pci->link_gen == 2) {
>  		/* Allow Gen2 mode after the link is up. */
> @@ -884,7 +886,9 @@ static int imx6_pcie_start_link(struct dw_pcie *pci)
>  		}
>  
>  		/* Make sure link training is finished as well! */
> -		dw_pcie_wait_for_link(pci);
> +		ret = dw_pcie_wait_for_link(pci);
> +		if (ret)
> +			goto err_reset_phy;
>  	} else {
>  		dev_info(dev, "Link: Gen2 disabled\n");
>  	}
> @@ -897,7 +901,6 @@ static int imx6_pcie_start_link(struct dw_pcie *pci)
>  	dev_dbg(dev, "PHY DEBUG_R0=0x%08x DEBUG_R1=0x%08x\n",
>  		dw_pcie_readl_dbi(pci, PCIE_PORT_DEBUG0),
>  		dw_pcie_readl_dbi(pci, PCIE_PORT_DEBUG1));
> -	imx6_pcie_reset_phy(imx6_pcie);
>  	return ret;
>  }
>  
> @@ -921,8 +924,29 @@ static int imx6_pcie_host_init(struct pcie_port *pp)
>  	return 0;
>  }
>  
> +static void imx6_pcie_host_exit(struct pcie_port *pp)
> +{
> +	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
> +	struct device *dev = pci->dev;
> +	struct imx6_pcie *imx6_pcie = to_imx6_pcie(pci);
> +
> +	imx6_pcie_reset_phy(imx6_pcie);
> +	imx6_pcie_clk_disable(imx6_pcie);
> +	switch (imx6_pcie->drvdata->variant) {
> +	case IMX8MM:
> +		if (phy_power_off(imx6_pcie->phy))
> +			dev_err(dev, "unable to power off phy\n");
> +		break;
> +	default:
> +		break;
> +	}
> +	if (imx6_pcie->vpcie)
> +		regulator_disable(imx6_pcie->vpcie);
> +}
> +
>  static const struct dw_pcie_host_ops imx6_pcie_host_ops = {
>  	.host_init = imx6_pcie_host_init,
> +	.host_exit = imx6_pcie_host_exit,
>  };
>  
>  static const struct dw_pcie_ops dw_pcie_ops = {
> -- 
> 2.25.1
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel