Linux-ARM-Kernel Archive on lore.kernel.org
 help / color / mirror / Atom feed
From: Jai Luthra <j-luthra@ti.com>
To: Nishanth Menon <nm@ti.com>, Vignesh Raghavendra <vigneshr@ti.com>,
	Rob Herring <robh+dt@kernel.org>,
	Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Cc: <linux-kernel@vger.kernel.org>,
	<linux-arm-kernel@lists.infradead.org>,
	<devicetree@vger.kernel.org>,
	Jayesh Choudhary <j-choudhary@ti.com>,
	Jai Luthra <j-luthra@ti.com>
Subject: [PATCH v3 2/2] arm64: dts: ti: am625-sk: Add audio output support
Date: Wed, 27 Apr 2022 14:20:53 +0530	[thread overview]
Message-ID: <20220427085053.14964-3-j-luthra@ti.com> (raw)
In-Reply-To: <20220427085053.14964-1-j-luthra@ti.com>

Add nodes for audio codec and sound card, enable the audio serializer
(McASP1) under use and update pinmux. Disable all other McASP nodes.

Audio input is currently not working properly, so the RX port on McASP1
is disabled for now, until the issue is debugged.

The serializer is shared between HDMI and codec. By default codec is
used for output, but it can be toggled to HDMI using a FET switch
connected to the MCASP1_FET_SEL (J24) header on the board.

Signed-off-by: Jai Luthra <j-luthra@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am625-sk.dts | 89 ++++++++++++++++++++++++++
 1 file changed, 89 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am625-sk.dts b/arch/arm64/boot/dts/ti/k3-am625-sk.dts
index 5c38ee5ff9b2..d082099b4efb 100644
--- a/arch/arm64/boot/dts/ti/k3-am625-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am625-sk.dts
@@ -121,6 +121,46 @@
 			 <3300000 0x1>;
 	};
 
+	vcc_1v8: regulator-5 {
+		/* output of TPS6282518DMQ */
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_3v3_sys>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	tlv320_mclk: clk-0 {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <12288000>;
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "AM62x-SKEVM";
+		simple-audio-card,widgets =
+			"Headphone", "Headphone Jack";
+		simple-audio-card,routing =
+			"Headphone Jack",	"HPLOUT",
+			"Headphone Jack",	"HPROUT";
+		simple-audio-card,format = "dsp_b";
+		simple-audio-card,bitclock-master = <&sound_master>;
+		simple-audio-card,frame-master = <&sound_master>;
+		simple-audio-card,bitclock-inversion;
+
+		simple-audio-card,cpu {
+			sound-dai = <&mcasp1>;
+		};
+
+		sound_master: simple-audio-card,codec {
+			sound-dai = <&tlv320aic3106>;
+			clocks = <&tlv320_mclk>;
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
@@ -266,6 +306,15 @@
 			AM62X_IOPAD(0x01d4, PIN_INPUT, 7) /* (B15) UART0_RTSn.GPIO1_23 */
 		>;
 	};
+
+	main_mcasp1_pins_default: main-mcasp1-pins-default {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x0090, PIN_INPUT, 2) /* (M24) GPMC0_BE0N_CLE.MCASP1_ACLKX */
+			AM62X_IOPAD(0x0098, PIN_INPUT, 2) /* (U23) GPMC0_WAIT0.MCASP1_AFSX */
+			AM62X_IOPAD(0x008c, PIN_OUTPUT, 2) /* (L25) GPMC0_WEN.MCASP1_AXR0 */
+			AM62X_IOPAD(0x0084, PIN_INPUT, 2) /* (L23) GPMC0_ADVN_ALE.MCASP1_AXR2 */
+		>;
+	};
 };
 
 &wkup_uart0 {
@@ -352,6 +401,18 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&main_gpio1_ioexp_intr_pins_default>;
 	};
+
+	tlv320aic3106: audio-codec@1b {
+		#sound-dai-cells = <0>;
+		compatible = "ti,tlv320aic3106";
+		reg = <0x1b>;
+
+		/* Regulators */
+		AVDD-supply = <&vcc_3v3_sys>;
+		IOVDD-supply = <&vcc_3v3_sys>;
+		DRVDD-supply = <&vcc_3v3_sys>;
+		DVDD-supply = <&vcc_1v8>;
+	};
 };
 
 &main_i2c2 {
@@ -412,6 +473,34 @@
 	};
 };
 
+&mcasp0 {
+	status = "disabled";
+};
+
+&mcasp1 {
+	status = "okay";
+	#sound-dai-cells = <0>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_mcasp1_pins_default>;
+
+	op-mode = <0>;          /* MCASP_IIS_MODE */
+	tdm-slots = <2>;
+
+	serial-dir = <  /* 0: INACTIVE, 1: TX, 2: RX */
+	       1 0 0 0
+	       0 0 0 0
+	       0 0 0 0
+	       0 0 0 0
+	>;
+	tx-num-evt = <32>;
+	rx-num-evt = <32>;
+};
+
+&mcasp2 {
+	status = "disabled";
+};
+
 &mailbox0_cluster0 {
 	mbox_m4_0: mbox-m4-0 {
 		ti,mbox-rx = <0 0 0>;
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

  parent reply	other threads:[~2022-04-27  8:52 UTC|newest]

Thread overview: 5+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2022-04-27  8:50 [PATCH v3 0/2] arm64: ti: k3-am62: Enable audio output Jai Luthra
2022-04-27  8:50 ` [PATCH v3 1/2] arm64: dts: ti: k3-am62-main: Add McASP nodes Jai Luthra
2022-06-18  1:16   ` Nishanth Menon
2022-04-27  8:50 ` Jai Luthra [this message]
2022-05-05  6:09 ` [PATCH v3 0/2] arm64: ti: k3-am62: Enable audio output Devarsh Thakkar

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20220427085053.14964-3-j-luthra@ti.com \
    --to=j-luthra@ti.com \
    --cc=devicetree@vger.kernel.org \
    --cc=j-choudhary@ti.com \
    --cc=krzysztof.kozlowski+dt@linaro.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=nm@ti.com \
    --cc=robh+dt@kernel.org \
    --cc=vigneshr@ti.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox