From: Logananth Sundararaj <logananth13.hcl@gmail.com>
To: Arnd Bergmann <arnd@arndb.de>, Olof Johansson <olof@lixom.net>,
soc@kernel.org, Rob Herring <robh+dt@kernel.org>,
Joel Stanley <joel@jms.id.au>, Andrew Jeffery <andrew@aj.id.au>,
linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, linux-aspeed@lists.ozlabs.org,
openbmc@lists.ozlabs.org
Cc: garnermic@gmail.com, thangavel.k@hcl.com, naveen.mosess@hcl.com,
patrick@stwcx.xyz, velumanit@hcl.com
Subject: [PATCH v3] The Yosemite V3.5 is a facebook multi-node server platform that host four OCP server. The BMC in the Yosemite V3.5 platform based on AST2600 SoC.
Date: Thu, 7 Jul 2022 18:50:54 +0530 [thread overview]
Message-ID: <20220707132054.GA10610@logan-ThinkPad-T14-Gen-1> (raw)
This patch adds linux device tree entry related to
Yosemite V3.5 specific devices connected to BMC SoC.
Signed-off-by: Logananth Sundararaj <logananth_s@hcl.com>
---
--- v3 - addressed v2 patch comments.
--- v2 - Enabled i2c drivers.
--- v1 - Initial draft.
---
---
arch/arm/boot/dts/Makefile | 1 +
.../boot/dts/aspeed-bmc-facebook-fby35.dts | 266 ++++++++++++++++++
2 files changed, 267 insertions(+)
create mode 100644 arch/arm/boot/dts/aspeed-bmc-facebook-fby35.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 7e0934180724..58add093e5fb 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1465,6 +1465,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
aspeed-bmc-facebook-cloudripper.dtb \
aspeed-bmc-facebook-cmm.dtb \
aspeed-bmc-facebook-elbert.dtb \
+ aspeed-bmc-facebook-fby35.dtb \
aspeed-bmc-facebook-fuji.dtb \
aspeed-bmc-facebook-galaxy100.dtb \
aspeed-bmc-facebook-minipack.dtb \
diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-fby35.dts b/arch/arm/boot/dts/aspeed-bmc-facebook-fby35.dts
new file mode 100644
index 000000000000..32262cf1d9ea
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed-bmc-facebook-fby35.dts
@@ -0,0 +1,266 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright (c) 2020 Facebook Inc.
+
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/i2c/i2c.h>
+
+/ {
+ model = "Facebook fby35";
+ compatible = "facebook,fby35", "aspeed,ast2600";
+
+ aliases {
+ serial4 = &uart5;
+ };
+
+ chosen {
+ stdout-path = &uart5;
+ bootargs = "console=ttyS4,57600n8 root=/dev/ram rw vmalloc=384M";
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x80000000 0x80000000>;
+ };
+
+ iio-hwmon {
+ compatible = "iio-hwmon";
+ io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>,
+ <&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>,
+ <&adc1 0>, <&adc1 1>, <&adc1 2>, <&adc1 3>,
+ <&adc1 4>, <&adc1 5>, <&adc1 6>;
+ };
+ spi_gpio: spi-gpio {
+ status = "okay";
+ compatible = "spi-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ gpio-sck = <&gpio0 ASPEED_GPIO(X, 3) GPIO_ACTIVE_HIGH>;
+ gpio-mosi = <&gpio0 ASPEED_GPIO(X, 4) GPIO_ACTIVE_HIGH>;
+ gpio-miso = <&gpio0 ASPEED_GPIO(X, 5) GPIO_ACTIVE_HIGH>;
+ num-chipselects = <1>;
+ cs-gpios = <&gpio0 ASPEED_GPIO(X, 0) GPIO_ACTIVE_LOW>;
+
+ tpmdev@0 {
+ compatible = "tcg,tpm_tis-spi";
+ spi-max-frequency = <33000000>;
+ reg = <0>;
+ };
+ };
+
+};
+
+&mac3 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rmii4_default>;
+ no-hw-checksum;
+ use-ncsi;
+ mlx,multi-host;
+ ncsi-ctrl,start-redo-probe;
+ ncsi-ctrl,no-channel-monitor;
+ ncsi-package = <1>;
+ ncsi-channel = <1>;
+ ncsi-rexmit = <1>;
+ ncsi-timeout = <2>;
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&uart3 {
+ status = "okay";
+};
+
+&uart4 {
+ status = "okay";
+};
+
+&uart5 {
+ status = "okay";
+ compatible = "snps,dw-apb-uart";
+};
+
+&wdt1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdtrst1_default>;
+ aspeed,reset-type = "soc";
+ aspeed,external-signal;
+ aspeed,ext-push-pull;
+ aspeed,ext-active-high;
+ aspeed,ext-pulse-duration = <256>;
+};
+
+&rtc {
+ status = "okay";
+};
+
+&fmc {
+ status = "okay";
+ flash@0 {
+ status = "okay";
+ m25p,fast-read;
+ label = "spi0.1";
+ spi-max-frequency = <50000000>;
+ #include "openbmc-flash-layout-128.dtsi"
+ };
+ flash@1 {
+ status = "okay";
+ m25p,fast-read;
+ label = "spi0.0";
+ spi-max-frequency = <50000000>;
+ #include "openbmc-flash-layout.dtsi"
+ };
+};
+
+&i2c0 {
+ //Host1 IPMB bus
+ status = "okay";
+ multi-master;
+ ipmb0@10 {
+ compatible = "ipmb-dev";
+ reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+ i2c-protocol;
+ };
+};
+
+&i2c1 {
+ //Host2 IPMB bus
+ status = "okay";
+ multi-master;
+ ipmb1@10 {
+ compatible = "ipmb-dev";
+ reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+ i2c-protocol;
+ };
+};
+
+&i2c2 {
+ //Host3 IPMB bus
+ status = "okay";
+ multi-master;
+ ipmb2@10 {
+ compatible = "ipmb-dev";
+ reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+ i2c-protocol;
+ };
+};
+
+&i2c3 {
+ //Host1 IPMB bus
+ status = "okay";
+ multi-master;
+ ipmb3@10 {
+ compatible = "ipmb-dev";
+ reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+ i2c-protocol;
+ };
+};
+
+&i2c4 {
+ status = "okay";
+};
+
+&i2c5 {
+ status = "okay";
+};
+
+&i2c6 {
+ status = "okay";
+};
+
+&i2c7 {
+ status = "okay";
+};
+
+&i2c8 {
+ //NIC SENSOR TEMP
+ status = "okay";
+ tmp421@1f {
+ compatible = "ti,tmp421";
+ reg = <0x1f>;
+ };
+};
+
+&i2c9 {
+ // Debug-Card IPMB bus
+ status = "okay";
+ multi-master;
+ ipmb9@30 {
+ compatible = "ipmb-dev";
+ reg = <(0x30 | I2C_OWN_SLAVE_ADDRESS)>;
+ i2c-protocol;
+ };
+};
+
+&i2c10 {
+ status = "okay";
+};
+
+&i2c11 {
+ status = "okay";
+ //FRU EEPROM
+ eeprom@51 {
+ compatible = "atmel,24c64";
+ reg = <0x51>;
+ pagesize = <32>;
+ };
+};
+
+&i2c12 {
+ status = "okay";
+ //INLET TEMP
+ tmp75@4e {
+ compatible = "ti,tmp75";
+ reg = <0x4e>;
+ };
+ //OUTLET TEMP
+ tmp75@4f {
+ compatible = "ti,tmp75";
+ reg = <0x4f>;
+ };
+};
+
+&i2c13 {
+ status = "okay";
+};
+
+&adc0 {
+ ref_voltage = <2500>;
+ status = "okay";
+
+ pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
+ &pinctrl_adc2_default &pinctrl_adc3_default
+ &pinctrl_adc4_default &pinctrl_adc5_default
+ &pinctrl_adc6_default &pinctrl_adc7_default>;
+};
+
+&adc1 {
+ ref_voltage = <2500>;
+ status = "okay";
+
+ pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
+ &pinctrl_adc10_default &pinctrl_adc11_default
+ &pinctrl_adc12_default &pinctrl_adc13_default>;
+};
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&uhci {
+ status = "okay";
+};
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next reply other threads:[~2022-07-07 13:22 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-07-07 13:20 Logananth Sundararaj [this message]
2022-07-07 13:33 ` [PATCH v3] The Yosemite V3.5 is a facebook multi-node server platform that host four OCP server. The BMC in the Yosemite V3.5 platform based on AST2600 SoC Arnd Bergmann
2022-07-14 18:05 ` Peter Delevoryas
2022-07-14 20:15 ` Arnd Bergmann
2022-07-14 20:24 ` Peter Delevoryas
2022-07-14 20:30 ` Peter Delevoryas
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20220707132054.GA10610@logan-ThinkPad-T14-Gen-1 \
--to=logananth13.hcl@gmail.com \
--cc=andrew@aj.id.au \
--cc=arnd@arndb.de \
--cc=devicetree@vger.kernel.org \
--cc=garnermic@gmail.com \
--cc=joel@jms.id.au \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-aspeed@lists.ozlabs.org \
--cc=linux-kernel@vger.kernel.org \
--cc=naveen.mosess@hcl.com \
--cc=olof@lixom.net \
--cc=openbmc@lists.ozlabs.org \
--cc=patrick@stwcx.xyz \
--cc=robh+dt@kernel.org \
--cc=soc@kernel.org \
--cc=thangavel.k@hcl.com \
--cc=velumanit@hcl.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox