From: Matt Ranostay <mranostay@ti.com>
To: <vigneshr@ti.com>, <nm@ti.com>, <robh+dt@kernel.org>
Cc: <devicetree@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>, Matt Ranostay <mranostay@ti.com>
Subject: [PATCH v3 1/9] arm64: dts: ti: k3-j721s2-main: Add support for USB
Date: Tue, 20 Sep 2022 20:13:19 -0700 [thread overview]
Message-ID: <20220921031327.4135-2-mranostay@ti.com> (raw)
In-Reply-To: <20220921031327.4135-1-mranostay@ti.com>
From: Aswath Govindraju <a-govindraju@ti.com>
Add support for single instance of USB 3.0 controller in J721S2 SoC.
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Acked-by: Matt Ranostay <mranostay@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
---
arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi | 42 ++++++++++++++++++++++
1 file changed, 42 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
index 34e7d577ae13..1f178ad3fa42 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
@@ -26,6 +26,20 @@ l3cache-sram@200000 {
};
};
+ scm_conf: syscon@104000 {
+ compatible = "ti,j721e-system-controller", "syscon", "simple-mfd";
+ reg = <0x00 0x00104000 0x00 0x18000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x00 0x00 0x00104000 0x18000>;
+
+ usb_serdes_mux: mux-controller-0 {
+ compatible = "mmio-mux";
+ #mux-control-cells = <1>;
+ mux-reg-masks = <0x0 0x8000000>; /* USB0 to SERDES0 lane 1/3 mux */
+ };
+ };
+
gic500: interrupt-controller@1800000 {
compatible = "arm,gic-v3";
#address-cells = <2>;
@@ -686,6 +700,34 @@ cpts@310d0000 {
};
};
+ usbss0: cdns-usb@4104000 {
+ compatible = "ti,j721e-usb";
+ reg = <0x00 0x04104000 0x00 0x100>;
+ clocks = <&k3_clks 360 16>, <&k3_clks 360 15>;
+ clock-names = "ref", "lpm";
+ assigned-clocks = <&k3_clks 360 16>; /* USB2_REFCLK */
+ assigned-clock-parents = <&k3_clks 360 17>;
+ power-domains = <&k3_pds 360 TI_SCI_PD_EXCLUSIVE>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ dma-coherent;
+
+ usb0: usb@6000000 {
+ compatible = "cdns,usb3";
+ reg = <0x00 0x06000000 0x00 0x10000>,
+ <0x00 0x06010000 0x00 0x10000>,
+ <0x00 0x06020000 0x00 0x10000>;
+ reg-names = "otg", "xhci", "dev";
+ interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "host", "peripheral", "otg";
+ maximum-speed = "super-speed";
+ dr_mode = "otg";
+ };
+ };
+
main_mcan0: can@2701000 {
compatible = "bosch,m_can";
reg = <0x00 0x02701000 0x00 0x200>,
--
2.37.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2022-09-21 3:15 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-09-21 3:13 [PATCH v3 0/9] J721S2: Add support for additional IPs Matt Ranostay
2022-09-21 3:13 ` Matt Ranostay [this message]
2022-09-21 3:13 ` [PATCH v3 2/9] arm64: dts: ti: k3-j721s2-main: Add SERDES and WIZ device tree node Matt Ranostay
2022-09-21 3:13 ` [PATCH v3 3/9] arm64: dts: ti: k3-j721s2-mcu-wakeup: Add support of OSPI Matt Ranostay
2022-09-21 3:13 ` [PATCH v3 4/9] arm64: dts: ti: k3-j721s2-common-proc-board: Enable SERDES0 Matt Ranostay
2022-09-21 3:13 ` [PATCH v3 5/9] arm64: dts: ti: k3-j721s2-common-proc-board: Add USB support Matt Ranostay
2022-09-21 3:13 ` [PATCH v3 6/9] arm64: dts: ti: k3-j721s2: Add support for OSPI Flashes Matt Ranostay
2022-09-21 3:13 ` [PATCH v3 7/9] dt-bindings: PCI: Add host mode device-id for j721s2 platform Matt Ranostay
2022-09-26 20:19 ` Rob Herring
2022-09-21 3:13 ` [PATCH v3 8/9] arm64: dts: ti: k3-j721s2-main: Add PCIe device tree node Matt Ranostay
2022-09-21 3:13 ` [PATCH v3 9/9] arm64: dts: ti: k3-j721s2-common-proc-board: Enable PCIe Matt Ranostay
2022-10-28 2:16 ` [PATCH v3 0/9] J721S2: Add support for additional IPs Nishanth Menon
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20220921031327.4135-2-mranostay@ti.com \
--to=mranostay@ti.com \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=nm@ti.com \
--cc=robh+dt@kernel.org \
--cc=vigneshr@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).