From: Sasha Levin <sashal@kernel.org>
To: linux-kernel@vger.kernel.org, stable@vger.kernel.org
Cc: Haibo Chen <haibo.chen@nxp.com>, Shawn Guo <shawnguo@kernel.org>,
Sasha Levin <sashal@kernel.org>,
robh+dt@kernel.org, devicetree@vger.kernel.org,
linux-arm-kernel@lists.infradead.org
Subject: [PATCH AUTOSEL 6.0 03/46] ARM: dts: imx7d-sdb: config the max pressure for tsc2046
Date: Tue, 11 Oct 2022 10:49:31 -0400 [thread overview]
Message-ID: <20221011145015.1622882-3-sashal@kernel.org> (raw)
In-Reply-To: <20221011145015.1622882-1-sashal@kernel.org>
From: Haibo Chen <haibo.chen@nxp.com>
[ Upstream commit e7c4ebe2f9cd68588eb24ba4ed122e696e2d5272 ]
Use the general touchscreen method to config the max pressure for
touch tsc2046(data sheet suggest 8 bit pressure), otherwise, for
ABS_PRESSURE, when config the same max and min value, weston will
meet the following issue,
[17:19:39.183] event1 - ADS7846 Touchscreen: is tagged by udev as: Touchscreen
[17:19:39.183] event1 - ADS7846 Touchscreen: kernel bug: device has min == max on ABS_PRESSURE
[17:19:39.183] event1 - ADS7846 Touchscreen: was rejected
[17:19:39.183] event1 - not using input device '/dev/input/event1'
This will then cause the APP weston-touch-calibrator can't list touch devices.
root@imx6ul7d:~# weston-touch-calibrator
could not load cursor 'dnd-move'
could not load cursor 'dnd-copy'
could not load cursor 'dnd-none'
No devices listed.
And accroding to binding Doc, "ti,x-max", "ti,y-max", "ti,pressure-max"
belong to the deprecated properties, so remove them. Also for "ti,x-min",
"ti,y-min", "ti,x-plate-ohms", the value set in dts equal to the default
value in driver, so are redundant, also remove here.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
arch/arm/boot/dts/imx7d-sdb.dts | 7 +------
1 file changed, 1 insertion(+), 6 deletions(-)
diff --git a/arch/arm/boot/dts/imx7d-sdb.dts b/arch/arm/boot/dts/imx7d-sdb.dts
index 78f4224a9bf4..e93b9cd9c27b 100644
--- a/arch/arm/boot/dts/imx7d-sdb.dts
+++ b/arch/arm/boot/dts/imx7d-sdb.dts
@@ -206,12 +206,7 @@ tsc2046@0 {
interrupt-parent = <&gpio2>;
interrupts = <29 0>;
pendown-gpio = <&gpio2 29 GPIO_ACTIVE_HIGH>;
- ti,x-min = /bits/ 16 <0>;
- ti,x-max = /bits/ 16 <0>;
- ti,y-min = /bits/ 16 <0>;
- ti,y-max = /bits/ 16 <0>;
- ti,pressure-max = /bits/ 16 <0>;
- ti,x-plate-ohms = /bits/ 16 <400>;
+ touchscreen-max-pressure = <255>;
wakeup-source;
};
};
--
2.35.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2022-10-11 14:52 UTC|newest]
Thread overview: 29+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <20221011145015.1622882-1-sashal@kernel.org>
2022-10-11 14:49 ` [PATCH AUTOSEL 6.0 02/46] ARM: dts: imx6: delete interrupts property if interrupts-extended is set Sasha Levin
2022-10-11 14:49 ` Sasha Levin [this message]
2022-10-11 14:49 ` [PATCH AUTOSEL 6.0 04/46] soc: mediatek: Let PMIC Wrapper and SCPSYS depend on OF Sasha Levin
2022-10-11 22:49 ` Jean Delvare
2022-10-16 14:46 ` Sasha Levin
2022-10-11 14:49 ` [PATCH AUTOSEL 6.0 06/46] ARM: dts: imx6q: add missing properties for sram Sasha Levin
2022-10-11 14:49 ` [PATCH AUTOSEL 6.0 07/46] ARM: dts: imx6dl: " Sasha Levin
2022-10-11 14:49 ` [PATCH AUTOSEL 6.0 08/46] ARM: dts: imx6qp: " Sasha Levin
2022-10-11 14:49 ` [PATCH AUTOSEL 6.0 09/46] ARM: dts: imx6sl: " Sasha Levin
2022-10-11 14:49 ` [PATCH AUTOSEL 6.0 10/46] ARM: dts: imx6sll: " Sasha Levin
2022-10-11 14:49 ` [PATCH AUTOSEL 6.0 11/46] ARM: dts: imx6sx: " Sasha Levin
2022-10-11 14:49 ` [PATCH AUTOSEL 6.0 12/46] ARM: dts: imx6sl: use tabs for code indent Sasha Levin
2022-10-11 14:49 ` [PATCH AUTOSEL 6.0 13/46] ARM: dts: imx6sx-udoo-neo: don't use multiple blank lines Sasha Levin
2022-10-11 14:49 ` [PATCH AUTOSEL 6.0 14/46] kselftest/arm64: Fix validatation termination record after EXTRA_CONTEXT Sasha Levin
2022-10-11 14:49 ` [PATCH AUTOSEL 6.0 15/46] kselftest/arm64: Allow larger buffers in get_signal_context() Sasha Levin
2022-10-11 15:04 ` Mark Brown
2022-10-13 17:58 ` Sasha Levin
2022-10-13 18:02 ` Mark Brown
2022-10-11 14:49 ` [PATCH AUTOSEL 6.0 17/46] arm64: atomics: remove LL/SC trampolines Sasha Levin
2022-10-12 8:55 ` Catalin Marinas
2022-10-11 14:49 ` [PATCH AUTOSEL 6.0 18/46] arm64: run softirqs on the per-CPU IRQ stack Sasha Levin
2022-10-11 14:49 ` [PATCH AUTOSEL 6.0 19/46] arm64: dts: imx8mm-kontron: Use the VSELECT signal to switch SD card IO voltage Sasha Levin
2022-10-11 14:49 ` [PATCH AUTOSEL 6.0 20/46] arm64: dts: imx8ulp: no executable source file permission Sasha Levin
2022-10-11 14:49 ` [PATCH AUTOSEL 6.0 21/46] arm64: dts: imx8mq-librem5: Add bq25895 as max17055's power supply Sasha Levin
2022-10-11 14:49 ` [PATCH AUTOSEL 6.0 22/46] ARM: orion: fix include path Sasha Levin
2022-10-11 14:50 ` [PATCH AUTOSEL 6.0 42/46] arm64: dts: uniphier: Add USB-device support for PXs3 reference board Sasha Levin
2022-10-11 14:50 ` [PATCH AUTOSEL 6.0 43/46] ARM: 9233/1: stacktrace: Skip frame pointer boundary check for call_with_stack() Sasha Levin
2022-10-11 14:50 ` [PATCH AUTOSEL 6.0 44/46] ARM: 9234/1: stacktrace: Avoid duplicate saving of exception PC value Sasha Levin
2022-10-11 14:50 ` [PATCH AUTOSEL 6.0 45/46] ARM: 9242/1: kasan: Only map modules if CONFIG_KASAN_VMALLOC=n Sasha Levin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20221011145015.1622882-3-sashal@kernel.org \
--to=sashal@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=haibo.chen@nxp.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh+dt@kernel.org \
--cc=shawnguo@kernel.org \
--cc=stable@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).