[PATCH v2 0/3] Improve K3-am625-sk support (USB, MMC)

[PATCH v2 0/3] Improve K3-am625-sk support (USB, MMC)

[Sjoerd Simons]

This series picks up a few patches from the TI BSP tree that
unfortunately didn't make it upstream thusfar.

The first patch improve SD card compatibility (allowing U1 class cards
to be used), the remaining ones add USB support.

The type-c connector isn't entirely modelled with these changes as
it goes through a TPS6598 PD controller. Unfortunately the dtb bindings
for that currently require an irq line, which is not connected on E1 and
E2 version boards. The patchese to support this setup unfortunately didn't land
yet[0].. As such the last patch ignored the PD controller and simply
configures usb0 as periphal only rather then mode switch capable, which
at least gives some basic usability of that USB port.

0: https://lore.kernel.org/lkml/f714ee55-ef47-317d-81b9-57020dda064b@ti.com/T/

Changes in v2:
  - Rebase against linux-next 20221220

Aswath Govindraju (2):
  arm64: dts: ti: k3-am62-main: Add support for USB
  arm64: dts: ti: k3-am625-sk: Add support for USB

Nitin Yadav (1):
  arm64: dts: ti: k3-am62-main: Update OTAP and ITAP delay select

 arch/arm64/boot/dts/ti/k3-am62-main.dtsi | 90 ++++++++++++++++++------
 arch/arm64/boot/dts/ti/k3-am625-sk.dts   | 50 +++++++++++++
 2 files changed, 118 insertions(+), 22 deletions(-)

-- 
2.39.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 1/3] arm64: dts: ti: k3-am62-main: Update OTAP and ITAP delay select

[Sjoerd Simons]

From: Nitin Yadav <n-yadav@ti.com>

UHS Class U1 sd-card are not getting detected due to incorrect
OTAP/ITAP delay select values in linux. Update OTAP and ITAP
delay select values for various speed modes. For sdhci0, update
OTAP delay values for ddr52 & HS200 and add ITAP delay for legacy
& mmc-hs. For sdhci1 & sdhci2, update OTAP & ITAP delay select
recommended as in RIOT for various speed modes.

Signed-off-by: Nitin Yadav <n-yadav@ti.com>
[cherry-pick from vendor BSP]
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>

---

Changes in v2:
  - Rebase against linux-next 20221220

 arch/arm64/boot/dts/ti/k3-am62-main.dtsi | 46 ++++++++++++------------
 1 file changed, 24 insertions(+), 22 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am62-main.dtsi b/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
index 072903649d6e..466b94d1cee9 100644
--- a/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
@@ -501,8 +501,10 @@ sdhci0: mmc@fa10000 {
 		ti,clkbuf-sel = <0x7>;
 		ti,otap-del-sel-legacy = <0x0>;
 		ti,otap-del-sel-mmc-hs = <0x0>;
-		ti,otap-del-sel-ddr52 = <0x9>;
-		ti,otap-del-sel-hs200 = <0x6>;
+		ti,otap-del-sel-ddr52 = <0x5>;
+		ti,otap-del-sel-hs200 = <0x5>;
+		ti,itap-del-sel-legacy = <0xa>;
+		ti,itap-del-sel-mmc-hs = <0x1>;
 		status = "disabled";
 	};
 
@@ -514,17 +516,17 @@ sdhci1: mmc@fa00000 {
 		clocks = <&k3_clks 58 5>, <&k3_clks 58 6>;
 		clock-names = "clk_ahb", "clk_xin";
 		ti,trm-icp = <0x2>;
-		ti,otap-del-sel-legacy = <0x0>;
+		ti,otap-del-sel-legacy = <0x8>;
 		ti,otap-del-sel-sd-hs = <0x0>;
-		ti,otap-del-sel-sdr12 = <0xf>;
-		ti,otap-del-sel-sdr25 = <0xf>;
-		ti,otap-del-sel-sdr50 = <0xc>;
-		ti,otap-del-sel-sdr104 = <0x6>;
-		ti,otap-del-sel-ddr50 = <0x9>;
-		ti,itap-del-sel-legacy = <0x0>;
-		ti,itap-del-sel-sd-hs = <0x0>;
-		ti,itap-del-sel-sdr12 = <0x0>;
-		ti,itap-del-sel-sdr25 = <0x0>;
+		ti,otap-del-sel-sdr12 = <0x0>;
+		ti,otap-del-sel-sdr25 = <0x0>;
+		ti,otap-del-sel-sdr50 = <0x8>;
+		ti,otap-del-sel-sdr104 = <0x7>;
+		ti,otap-del-sel-ddr50 = <0x4>;
+		ti,itap-del-sel-legacy = <0xa>;
+		ti,itap-del-sel-sd-hs = <0x1>;
+		ti,itap-del-sel-sdr12 = <0xa>;
+		ti,itap-del-sel-sdr25 = <0x1>;
 		ti,clkbuf-sel = <0x7>;
 		bus-width = <4>;
 		status = "disabled";
@@ -538,17 +540,17 @@ sdhci2: mmc@fa20000 {
 		clocks = <&k3_clks 184 5>, <&k3_clks 184 6>;
 		clock-names = "clk_ahb", "clk_xin";
 		ti,trm-icp = <0x2>;
-		ti,otap-del-sel-legacy = <0x0>;
+		ti,otap-del-sel-legacy = <0x8>;
 		ti,otap-del-sel-sd-hs = <0x0>;
-		ti,otap-del-sel-sdr12 = <0xf>;
-		ti,otap-del-sel-sdr25 = <0xf>;
-		ti,otap-del-sel-sdr50 = <0xc>;
-		ti,otap-del-sel-sdr104 = <0x6>;
-		ti,otap-del-sel-ddr50 = <0x9>;
-		ti,itap-del-sel-legacy = <0x0>;
-		ti,itap-del-sel-sd-hs = <0x0>;
-		ti,itap-del-sel-sdr12 = <0x0>;
-		ti,itap-del-sel-sdr25 = <0x0>;
+		ti,otap-del-sel-sdr12 = <0x0>;
+		ti,otap-del-sel-sdr25 = <0x0>;
+		ti,otap-del-sel-sdr50 = <0x8>;
+		ti,otap-del-sel-sdr104 = <0x7>;
+		ti,otap-del-sel-ddr50 = <0x8>;
+		ti,itap-del-sel-legacy = <0xa>;
+		ti,itap-del-sel-sd-hs = <0xa>;
+		ti,itap-del-sel-sdr12 = <0xa>;
+		ti,itap-del-sel-sdr25 = <0x1>;
 		ti,clkbuf-sel = <0x7>;
 		status = "disabled";
 	};
-- 
2.39.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 2/3] arm64: dts: ti: k3-am62-main: Add support for USB

[Sjoerd Simons]

From: Aswath Govindraju <a-govindraju@ti.com>

AM62 SoC has two instances of USB on it. Therefore, add support for the
same.

Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
[cherry-pick from vendor BSP]]
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>

---

Changes in v2:
  - Rebase against linux-next 20221220

 arch/arm64/boot/dts/ti/k3-am62-main.dtsi | 44 ++++++++++++++++++++++++
 1 file changed, 44 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am62-main.dtsi b/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
index 466b94d1cee9..4da15e8c956f 100644
--- a/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
@@ -555,6 +555,50 @@ sdhci2: mmc@fa20000 {
 		status = "disabled";
 	};
 
+	usbss0: dwc3-usb@f900000 {
+		compatible = "ti,am62-usb";
+		reg = <0x00 0x0f900000 0x00 0x800>;
+		clocks = <&k3_clks 161 3>;
+		clock-names = "ref";
+		ti,syscon-phy-pll-refclk = <&wkup_conf 0x4008>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		power-domains = <&k3_pds 178 TI_SCI_PD_EXCLUSIVE>;
+		ranges;
+
+		usb0: usb@31000000 {
+			compatible = "snps,dwc3";
+			reg =<0x00 0x31000000 0x00 0x50000>;
+			interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */
+				     <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>; /* irq.0 */
+			interrupt-names = "host", "peripheral";
+			maximum-speed = "high-speed";
+			dr_mode = "otg";
+		};
+	};
+
+	usbss1: dwc3-usb@f910000 {
+		compatible = "ti,am62-usb";
+		reg = <0x00 0x0f910000 0x00 0x800>;
+		clocks = <&k3_clks 162 3>;
+		clock-names = "ref";
+		ti,syscon-phy-pll-refclk = <&wkup_conf 0x4018>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		power-domains = <&k3_pds 179 TI_SCI_PD_EXCLUSIVE>;
+		ranges;
+
+		usb1: usb@31100000 {
+			compatible = "snps,dwc3";
+			reg =<0x00 0x31100000 0x00 0x50000>;
+			interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */
+				     <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>; /* irq.0 */
+			interrupt-names = "host", "peripheral";
+			maximum-speed = "high-speed";
+			dr_mode = "otg";
+		};
+	};
+
 	fss: bus@fc00000 {
 		compatible = "simple-bus";
 		reg = <0x00 0x0fc00000 0x00 0x70000>;
-- 
2.39.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 3/3] arm64: dts: ti: k3-am625-sk: Add support for USB

[Sjoerd Simons]

From: Aswath Govindraju <a-govindraju@ti.com>

AM62 SoC has two instances of USB and they are brought on to the board
in the following way,

-> USB0 instance
 - This is brought out to a USB TypeC connector on board through TPS6598 PD
   controller. The PD controller should decide the role based on CC pin in
   the connector. Unfortunately the irq line for the TPS isn't hooked up
   which is a mode not yet support by the driver (some patches were
   submitted earlier this year[0]). So for now the PD controller is left
   out and periphal mode chosen.

-> USB1 instance
 - This is brought out to a USB TypeA connector on board.

Therefore, add the required device tree support for the above in the board
dts file.

0: https://lore.kernel.org/lkml/f714ee55-ef47-317d-81b9-57020dda064b@ti.com/T/

Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
[merge from vendor bsp, drop TPS6598 support, reword commit message]
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>

---

Changes in v2:
  - Rebase against linux-next 20221220

 arch/arm64/boot/dts/ti/k3-am625-sk.dts | 50 ++++++++++++++++++++++++++
 1 file changed, 50 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am625-sk.dts b/arch/arm64/boot/dts/ti/k3-am625-sk.dts
index 4f179b146cab..c82a0ebf6772 100644
--- a/arch/arm64/boot/dts/ti/k3-am625-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am625-sk.dts
@@ -24,6 +24,8 @@ aliases {
 		spi0 = &ospi0;
 		ethernet0 = &cpsw_port1;
 		ethernet1 = &cpsw_port2;
+		usb0 = &usb0;
+		usb1 = &usb1;
 	};
 
 	chosen {
@@ -284,6 +286,12 @@ main_gpio1_ioexp_intr_pins_default: main-gpio1-ioexp-intr-pins-default {
 			AM62X_IOPAD(0x01d4, PIN_INPUT, 7) /* (B15) UART0_RTSn.GPIO1_23 */
 		>;
 	};
+
+	main_usb1_pins_default: main-usb1-pins-default {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x0258, PIN_OUTPUT, 0) /* (F18) USB1_DRVVBUS */
+		>;
+	};
 };
 
 &wkup_uart0 {
@@ -464,3 +472,45 @@ partition@3fc0000 {
 		};
 	};
 };
+
+&ecap0 {
+	status = "disabled";
+};
+
+&ecap1 {
+	status = "disabled";
+};
+
+&ecap2 {
+	status = "disabled";
+};
+
+&main_mcan0 {
+	status = "disabled";
+};
+
+&epwm0 {
+	status = "disabled";
+};
+
+&epwm1 {
+	status = "disabled";
+};
+
+&epwm2 {
+	status = "disabled";
+};
+
+&usbss0 {
+	ti,vbus-divider;
+};
+
+&usb0 {
+	dr_mode = "peripheral";
+};
+
+&usb1 {
+	dr_mode = "host";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_usb1_pins_default>;
+};
-- 
2.39.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel