From: Samuel Holland <samuel@sholland.org>
To: Chen-Yu Tsai <wens@csie.org>,
Jernej Skrabec <jernej.skrabec@gmail.com>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Rob Herring <robh+dt@kernel.org>
Cc: linux-sunxi@lists.linux.dev, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
Samuel Holland <samuel@sholland.org>
Subject: [PATCH 2/2] ARM: dts: sun8i: A33: Add iNet U70B Rev 01
Date: Thu, 29 Dec 2022 16:45:47 -0600 [thread overview]
Message-ID: <20221229224547.25225-3-samuel@sholland.org> (raw)
In-Reply-To: <20221229224547.25225-1-samuel@sholland.org>
This is a white-label 7" tablet board based on the A33 SoC. It features
a generic 1024x600 DPI panel, raw NAND for storage, and a Realtek 8723CS
Wi-Fi/Bluetooth chip.
Signed-off-by: Samuel Holland <samuel@sholland.org>
---
arch/arm/boot/dts/Makefile | 1 +
.../boot/dts/sun8i-a33-inet-u70b-rev01.dts | 172 ++++++++++++++++++
2 files changed, 173 insertions(+)
create mode 100644 arch/arm/boot/dts/sun8i-a33-inet-u70b-rev01.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index c014f4fc53c0..e4e985d5a66c 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1349,6 +1349,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
sun8i-a33-et-q8-v1.6.dtb \
sun8i-a33-ga10h-v1.1.dtb \
sun8i-a33-inet-d978-rev2.dtb \
+ sun8i-a33-inet-u70b-rev01.dtb \
sun8i-a33-ippo-q8h-v1.2.dtb \
sun8i-a33-olinuxino.dtb \
sun8i-a33-q8-tablet.dtb \
diff --git a/arch/arm/boot/dts/sun8i-a33-inet-u70b-rev01.dts b/arch/arm/boot/dts/sun8i-a33-inet-u70b-rev01.dts
new file mode 100644
index 000000000000..ac108a632659
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-a33-inet-u70b-rev01.dts
@@ -0,0 +1,172 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+
+/dts-v1/;
+
+#include "sun8i-a33.dtsi"
+#include "sun8i-reference-design-tablet.dtsi"
+
+/ {
+ model = "iNet U70B Rev 01";
+ compatible = "inet-tek,inet-u70b-rev01", "allwinner,sun8i-a33";
+
+ aliases {
+ ethernet0 = &rtl8723cs;
+ };
+
+ panel: panel {
+ compatible = "panel-dpi";
+ backlight = <&backlight>;
+ enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
+ power-supply = <®_dc1sw>;
+
+ panel-timing {
+ clock-frequency = <51000000>;
+ hactive = <1024>;
+ vactive = <600>;
+ hfront-porch = <162>;
+ hback-porch = <158>;
+ hsync-len = <20>;
+ vback-porch = <25>;
+ vfront-porch = <10>;
+ vsync-len = <3>;
+ hsync-active = <1>;
+ vsync-active = <1>;
+ };
+
+ port {
+ panel_in_tcon0: endpoint {
+ remote-endpoint = <&tcon0_out_panel>;
+ };
+ };
+ };
+
+ speaker_amp: audio-amplifier {
+ compatible = "simple-audio-amplifier";
+ enable-gpios = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */
+ sound-name-prefix = "Speaker Amp";
+ };
+
+ wifi_pwrseq: wifi-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&r_pio 0 6 GPIO_ACTIVE_LOW>; /* PL6 */
+ post-power-on-delay-ms = <200>;
+ };
+};
+
+&codec {
+ status = "okay";
+};
+
+&dai {
+ status = "okay";
+};
+
+&de {
+ status = "okay";
+};
+
+&i2c1 {
+ clock-frequency = <400000>;
+
+ accelerometer@18 {
+ compatible = "bosch,bma250";
+ reg = <0x18>;
+ interrupt-parent = <&pio>;
+ interrupts = <7 10 IRQ_TYPE_EDGE_RISING>; /* PH10 / EINT10 */
+ };
+};
+
+&mmc1 {
+ pinctrl-0 = <&mmc1_pg_pins>;
+ pinctrl-names = "default";
+ bus-width = <4>;
+ non-removable;
+ vmmc-supply = <®_dldo1>;
+ vqmmc-supply = <®_dldo2>;
+ status = "okay";
+
+ rtl8723cs: wifi@1 {
+ reg = <1>;
+ interrupt-parent = <&r_pio>;
+ interrupts = <0 7 IRQ_TYPE_LEVEL_LOW>; /* PL7 */
+ };
+};
+
+&nfc {
+ status = "okay";
+
+ nand@0 {
+ reg = <0>;
+ allwinner,rb = <0>;
+ };
+};
+
+&r_uart {
+ status = "disabled";
+};
+
+®_dldo2 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi-io";
+};
+
+&simplefb_lcd {
+ status = "okay";
+};
+
+&sound {
+ simple-audio-card,aux-devs = <&codec_analog>, <&speaker_amp>;
+ simple-audio-card,widgets = "Headphone", "Headphone Jack",
+ "Microphone", "Internal Microphone",
+ "Speaker", "Internal Speaker";
+ simple-audio-card,routing = "Headphone Jack", "HP",
+ "Internal Speaker", "Speaker Amp OUTL",
+ "Internal Speaker", "Speaker Amp OUTR",
+ "Speaker Amp INL", "HP", /* PHONEOUT ??? */
+ "Speaker Amp INR", "HP", /* PHONEOUT ??? */
+ "Left DAC", "DACL",
+ "Right DAC", "DACR",
+ "ADCL", "Left ADC",
+ "ADCR", "Right ADC",
+ "MIC1", "Internal Microphone",
+ "MIC2", "Headset Microphone",
+ "Headset Microphone", "HBIAS",
+ "Internal Microphone", "MBIAS";
+ status = "okay";
+};
+
+&tcon0 {
+ pinctrl-0 = <&lcd_rgb666_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&tcon0_out {
+ tcon0_out_panel: endpoint {
+ remote-endpoint = <&panel_in_tcon0>;
+ };
+};
+
+&touchscreen {
+ reg = <0x40>;
+ compatible = "silead,gsl1680";
+ avdd-supply = <®_ldo_io1>;
+ touchscreen-size-x = <1024>;
+ touchscreen-size-y = <600>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-0 = <&uart1_pg_pins>, <&uart1_cts_rts_pg_pins>;
+ pinctrl-names = "default";
+ uart-has-rtscts;
+ status = "okay";
+
+ bluetooth {
+ compatible = "realtek,rtl8723cs-bt";
+ device-wake-gpios = <&r_pio 0 10 GPIO_ACTIVE_LOW>; /* PL10 */
+ enable-gpios = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
+ host-wake-gpios = <&r_pio 0 9 GPIO_ACTIVE_HIGH>; /* PL9 */
+ };
+};
--
2.37.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2022-12-29 22:47 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-12-29 22:45 [PATCH 0/2] iNet U70B Rev 01 Tablet Support Samuel Holland
2022-12-29 22:45 ` [PATCH 1/2] dt-bindings: arm: sunxi: Add iNet U70B Rev 01 Tablet Samuel Holland
2022-12-30 7:53 ` Krzysztof Kozlowski
2022-12-29 22:45 ` Samuel Holland [this message]
2023-01-08 20:08 ` [PATCH 0/2] iNet U70B Rev 01 Tablet Support Jernej Škrabec
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20221229224547.25225-3-samuel@sholland.org \
--to=samuel@sholland.org \
--cc=devicetree@vger.kernel.org \
--cc=jernej.skrabec@gmail.com \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-sunxi@lists.linux.dev \
--cc=robh+dt@kernel.org \
--cc=wens@csie.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox