[PATCH v3 2/9] ARM: dts: amlogic: Used onboard usb hub reset on odroid c1

[PATCH v3 2/9] ARM: dts: amlogic: Used onboard usb hub reset on odroid c1

[Anand Moon]

On Odroid c1 previously use gpio-hog to reset the usb hub,
switch to used on board usb hub reset to enable the usb hub
and enable power to usb hub.

Add usb hub regulator as per the schematic.

Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
---
v3 - Add Rev by Neil.
     update the subject with odroid C1
     dropped dr_mode
v2 - drop the vendor name from compatible string.
   - move the hub node to USB controller node.
   - drop the usb_otg_pwr since it only liked to OTG port
     and link p5v0 to the vdd-supply.
---
 arch/arm/boot/dts/meson8b-odroidc1.dts | 23 ++++++++++-------------
 1 file changed, 10 insertions(+), 13 deletions(-)

diff --git a/arch/arm/boot/dts/meson8b-odroidc1.dts b/arch/arm/boot/dts/meson8b-odroidc1.dts
index 04356bc639fa..04c4bdca0b85 100644
--- a/arch/arm/boot/dts/meson8b-odroidc1.dts
+++ b/arch/arm/boot/dts/meson8b-odroidc1.dts
@@ -281,19 +281,6 @@ &gpio_ao {
 			  "J7 Header Pin 6", "J7 Header Pin 5",
 			  "J7 Header Pin 7", "HDMI_CEC",
 			  "SYS_LED", "", "";
-
-	/*
-	 * WARNING: The USB Hub on the Odroid-C1/C1+ needs a reset signal
-	 * to be turned high in order to be detected by the USB Controller.
-	 * This signal should be handled by a USB specific power sequence
-	 * in order to reset the Hub when USB bus is powered down.
-	 */
-	usb-hub {
-		gpio-hog;
-		gpios = <GPIOAO_4 GPIO_ACTIVE_HIGH>;
-		output-high;
-		line-name = "usb-hub-reset";
-	};
 };
 
 &ir_receiver {
@@ -381,5 +368,15 @@ &usb1_phy {
 };
 
 &usb1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
 	status = "okay";
+
+	hub@1 {
+		/* Genesys Logic GL852G usb hub */
+		compatible = "usb5e3,610";
+		reg = <1>;
+		vdd-supply = <&p5v0>;
+		reset-gpio = <&gpio_ao GPIOAO_4 GPIO_ACTIVE_LOW>;
+	};
 };
-- 
2.38.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 3/9] arm64: dts: amlogic: Used onboard usb hub reset on odroid c2

[Anand Moon]

On Odroid c2 previously use gpio-hog to reset the usb hub,
switch to used on-board usb hub reset to enable the usb hub
and enable power to hub.

Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
---
v3 - Add rev by Neil.
     droped dr_mode
v2 - drop the vendor name from compatible string.
   - move the hub node to USB controller node.
   - drop the usb_otg_pwr since it only liked to OTG port
         and link p5v0 to the vdd-supply.
---
 .../boot/dts/amlogic/meson-gxbb-odroidc2.dts  | 25 ++++++++-----------
 1 file changed, 10 insertions(+), 15 deletions(-)

diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
index 201596247fd9..70b10934a811 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
@@ -250,21 +250,6 @@ eth_phy0: ethernet-phy@0 {
 	};
 };
 
-&gpio_ao {
-	/*
-	 * WARNING: The USB Hub on the Odroid-C2 needs a reset signal
-	 * to be turned high in order to be detected by the USB Controller
-	 * This signal should be handled by a USB specific power sequence
-	 * in order to reset the Hub when USB bus is powered down.
-	 */
-	hog-0 {
-		gpio-hog;
-		gpios = <GPIOAO_4 GPIO_ACTIVE_HIGH>;
-		output-high;
-		line-name = "usb-hub-reset";
-	};
-};
-
 &hdmi_tx {
 	status = "okay";
 	pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
@@ -414,5 +399,15 @@ &usb0 {
 };
 
 &usb1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
 	status = "okay";
+
+	hub@1 {
+		/* Genesys Logic GL852G USB 2.0 hub */
+		compatible = "usb5e3,610";
+		reg = <1>;
+		vdd-supply = <&p5v0>;
+		reset-gpio = <&gpio_ao GPIOAO_4 GPIO_ACTIVE_LOW>;
+	};
 };
-- 
2.38.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 7/9] arm64: dts: amlogic: Used onboard usb hub reset on odroid c4

[Anand Moon]

On Odroid c4 previously use gpio-hog to reset the usb hub,
switch to used on-board usb hub reset to enable the usb hub
and enable power to hub.

USB hub is combination of USB 2.0 and USB 3.0 root hub so
use peer-hub node to link then.

Signed-off-by: Anand Moon <linux.amoon@gmail.com>
---
v3: - move the usb hub under dwc3 node.
      dropped dr_mode
v2: - fix the compatible string.
    - Fix the hub node to use peer-hub to link the usb 2.0 and usb 3.0.
---
 .../boot/dts/amlogic/meson-sm1-odroid-c4.dts  | 33 ++++++++++++-------
 1 file changed, 21 insertions(+), 12 deletions(-)

diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-odroid-c4.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-odroid-c4.dts
index 8c30ce63686e..a988015dd2d5 100644
--- a/arch/arm64/boot/dts/amlogic/meson-sm1-odroid-c4.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-sm1-odroid-c4.dts
@@ -28,18 +28,27 @@ sound {
 	};
 };
 
-&gpio {
-	/*
-	 * WARNING: The USB Hub on the Odroid-C4 needs a reset signal
-	 * to be turned high in order to be detected by the USB Controller
-	 * This signal should be handled by a USB specific power sequence
-	 * in order to reset the Hub when USB bus is powered down.
-	 */
-	hog-0 {
-		gpio-hog;
-		gpios = <GPIOH_4 GPIO_ACTIVE_HIGH>;
-		output-high;
-		line-name = "usb-hub-reset";
+&dwc3 {
+	/* USB hub supports both USB 2.0 and USB 3.0 root hub */
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	/* 2.0 hub on port 1 */
+	hub_2_0: hub@1 {
+		compatible = "usb2109,2817";
+		reg = <1>;
+		peer-hub = <&hub_3_0>;
+		reset-gpios = <&gpio GPIOH_4 GPIO_ACTIVE_LOW>;
+		vdd-supply = <&vcc_5v>;
+	};
+
+	/* 3.1 hub on port 4 */
+	hub_3_0: hub@2 {
+		compatible = "usb2109,817";
+		reg = <2>;
+		peer-hub = <&hub_2_0>;
+		reset-gpios = <&gpio GPIOH_4 GPIO_ACTIVE_LOW>;
+		vdd-supply = <&vcc_5v>;
 	};
 };
 
-- 
2.38.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 9/9] arm64: defconfig: Enable USB onboard HUB driver

[Anand Moon]

Enable the USB onboard HUB driver, used on Amlogic boards.

Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
---
v3: add rev Neil
v2: none
---
 arch/arm64/configs/defconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index 851e8f9be06d..42c3528a2473 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -923,6 +923,7 @@ CONFIG_USB_SERIAL_CP210X=m
 CONFIG_USB_SERIAL_FTDI_SIO=m
 CONFIG_USB_SERIAL_OPTION=m
 CONFIG_USB_HSIC_USB3503=y
+CONFIG_USB_ONBOARD_HUB=m
 CONFIG_NOP_USB_XCEIV=y
 CONFIG_USB_GADGET=y
 CONFIG_USB_RENESAS_USBHS_UDC=m
-- 
2.38.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v3 3/9] arm64: dts: amlogic: Used onboard usb hub reset on odroid c2

[Ben Wolsieffer]

On Sat, Jan 21, 2023 at 05:56:31PM +0000, Anand Moon wrote:
> On Odroid c2 previously use gpio-hog to reset the usb hub,
> switch to used on-board usb hub reset to enable the usb hub
> and enable power to hub.
> 
> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
> Signed-off-by: Anand Moon <linux.amoon@gmail.com>
> ---
> v3 - Add rev by Neil.
>      droped dr_mode
> v2 - drop the vendor name from compatible string.
>    - move the hub node to USB controller node.
>    - drop the usb_otg_pwr since it only liked to OTG port
>          and link p5v0 to the vdd-supply.
> ---
>  .../boot/dts/amlogic/meson-gxbb-odroidc2.dts  | 25 ++++++++-----------
>  1 file changed, 10 insertions(+), 15 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
> index 201596247fd9..70b10934a811 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
> @@ -250,21 +250,6 @@ eth_phy0: ethernet-phy@0 {
>  	};
>  };
>  
> -&gpio_ao {
> -	/*
> -	 * WARNING: The USB Hub on the Odroid-C2 needs a reset signal
> -	 * to be turned high in order to be detected by the USB Controller
> -	 * This signal should be handled by a USB specific power sequence
> -	 * in order to reset the Hub when USB bus is powered down.
> -	 */
> -	hog-0 {
> -		gpio-hog;
> -		gpios = <GPIOAO_4 GPIO_ACTIVE_HIGH>;
> -		output-high;
> -		line-name = "usb-hub-reset";
> -	};
> -};
> -
>  &hdmi_tx {
>  	status = "okay";
>  	pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
> @@ -414,5 +399,15 @@ &usb0 {
>  };
>  
>  &usb1 {
> +	#address-cells = <1>;
> +	#size-cells = <0>;
>  	status = "okay";
> +
> +	hub@1 {
> +		/* Genesys Logic GL852G USB 2.0 hub */
> +		compatible = "usb5e3,610";
> +		reg = <1>;
> +		vdd-supply = <&p5v0>;
> +		reset-gpio = <&gpio_ao GPIOAO_4 GPIO_ACTIVE_LOW>;
> +	};
>  };
> -- 
> 2.38.1
> 

Hello,

This patch breaks USB support on the ODROID-C2. As soon as the
onboard_usb_hub module is loaded, all USB devices disconnect.
Blacklisting onboard_usb_hub makes USB work as expected.

I tried to reproduce the problem by manually toggling the reset line,
but the problem seems to be specific to this driver. When reset is
asserted manually, the devices disconnect, but they all enumerate again
as soon as reset is released.

Also, I have been unable to make USB work again (until the next reboot)
even after unloading onboard_usb_hub.

Ben

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v3 3/9] arm64: dts: amlogic: Used onboard usb hub reset on odroid c2

[Krzysztof Kozlowski]

On 02/08/2023 23:06, Ben Wolsieffer wrote:
> On Sat, Jan 21, 2023 at 05:56:31PM +0000, Anand Moon wrote:
>> On Odroid c2 previously use gpio-hog to reset the usb hub,
>> switch to used on-board usb hub reset to enable the usb hub
>> and enable power to hub.
>>

...

>> +	hub@1 {
>> +		/* Genesys Logic GL852G USB 2.0 hub */
>> +		compatible = "usb5e3,610";
>> +		reg = <1>;
>> +		vdd-supply = <&p5v0>;
>> +		reset-gpio = <&gpio_ao GPIOAO_4 GPIO_ACTIVE_LOW>;
>> +	};
>>  };
>> -- 
>> 2.38.1
>>
> 
> Hello,
> 
> This patch breaks USB support on the ODROID-C2. As soon as the
> onboard_usb_hub module is loaded, all USB devices disconnect.
> Blacklisting onboard_usb_hub makes USB work as expected.
> 
> I tried to reproduce the problem by manually toggling the reset line,
> but the problem seems to be specific to this driver. When reset is
> asserted manually, the devices disconnect, but they all enumerate again
> as soon as reset is released.
> 
> Also, I have been unable to make USB work again (until the next reboot)
> even after unloading onboard_usb_hub.

Wasn't this patch made exactly to fix USB support, not break it? I might
be missing something but maybe this was not tested at all?

Best regards,
Krzysztof


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v3 3/9] arm64: dts: amlogic: Used onboard usb hub reset on odroid c2

[Ben Wolsieffer]

On Sat, Aug 05, 2023 at 11:30:21PM +0200, Krzysztof Kozlowski wrote:
> On 02/08/2023 23:06, Ben Wolsieffer wrote:
> > 
> > Hello,
> > 
> > This patch breaks USB support on the ODROID-C2. As soon as the
> > onboard_usb_hub module is loaded, all USB devices disconnect.
> > Blacklisting onboard_usb_hub makes USB work as expected.
> > 
> > I tried to reproduce the problem by manually toggling the reset line,
> > but the problem seems to be specific to this driver. When reset is
> > asserted manually, the devices disconnect, but they all enumerate again
> > as soon as reset is released.
> > 
> > Also, I have been unable to make USB work again (until the next reboot)
> > even after unloading onboard_usb_hub.
> 
> Wasn't this patch made exactly to fix USB support, not break it? I might
> be missing something but maybe this was not tested at all?
> 
> Best regards,
> Krzysztof
>

I have been using USB on the ODROID-C2 for several years without issues.
It looks to me that this patch was designed to make reset control for
the hub more elegant, rather than fix a specific issue. The same change
was applied to several devices, so it seems plausible that it was not
tested on all of them.

Thanks, Ben

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v3 3/9] arm64: dts: amlogic: Used onboard usb hub reset on odroid c2

[Anand Moon]

Hi Ben,

On Sun, 6 Aug 2023 at 05:35, Ben Wolsieffer <benwolsieffer@gmail.com> wrote:
>
> On Sat, Aug 05, 2023 at 11:30:21PM +0200, Krzysztof Kozlowski wrote:
> > On 02/08/2023 23:06, Ben Wolsieffer wrote:
> > >
> > > Hello,
> > >
> > > This patch breaks USB support on the ODROID-C2. As soon as the
> > > onboard_usb_hub module is loaded, all USB devices disconnect.
> > > Blacklisting onboard_usb_hub makes USB work as expected.
> > >
> > > I tried to reproduce the problem by manually toggling the reset line,
> > > but the problem seems to be specific to this driver. When reset is
> > > asserted manually, the devices disconnect, but they all enumerate again
> > > as soon as reset is released.
> > >
> > > Also, I have been unable to make USB work again (until the next reboot)
> > > even after unloading onboard_usb_hub.
> >
> > Wasn't this patch made exactly to fix USB support, not break it? I might
> > be missing something but maybe this was not tested at all?
> >
> > Best regards,
> > Krzysztof
> >
>
> I have been using USB on the ODROID-C2 for several years without issues.
> It looks to me that this patch was designed to make reset control for
> the hub more elegant, rather than fix a specific issue. The same change
> was applied to several devices, so it seems plausible that it was not
> tested on all of them.
>

We tried to fix quite a few issues in the past but still, we could not
resolve core issues.
Will try to resolve these issues in the future.
I have tested these changes at my end on Odroid C1+, Odroid C2, and Odroid C4,

> Thanks, Ben

Thanks
-Anand

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel