Linux-ARM-Kernel Archive on lore.kernel.org
 help / color / mirror / Atom feed
From: Esteban Blanc <eblanc@baylibre.com>
To: nm@ti.com, vigneshr@ti.com, kristo@kernel.org,
	robh+dt@kernel.org, krzysztof.kozlowski+dt@linaro.org
Cc: linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org, sterzik@ti.com, u-kumar1@ti.com,
	eblanc@baylibre.com, jneanne@baylibre.com, jpanis@baylibre.com
Subject: [PATCH v1 1/4] arm64: dts: ti: k3-j7200-som-p0: Add TP6594 family PMICs
Date: Wed, 29 Mar 2023 16:29:45 +0200	[thread overview]
Message-ID: <20230329142948.833800-2-eblanc@baylibre.com> (raw)
In-Reply-To: <20230329142948.833800-1-eblanc@baylibre.com>

This patch adds support for TPS6594 PMIC family on wakup I2C0 bus.
Theses devices provides regulators (bucks and LDOs), but also
GPIOs, a RTC, a watchdog, an ESM (Error Signal Monitor)
which monitors the SoC error output signal, and a PFSM
(Pre-configurable Finite State Machine) which manages the
operational modes of the PMIC.

Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
---
 arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi | 170 ++++++++++++++++++++
 1 file changed, 170 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
index fa44ed4c17d5..a6c085256a50 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
@@ -118,6 +118,25 @@ J721E_WKUP_IOPAD(0x0008, PIN_INPUT, 0)  /* MCU_OSPI0_DQS */
 	};
 };
 
+&wkup_pmx2 {
+	/* wkup_pmx2 starts at 0x68 */
+	wkup_i2c0_pins_default: wkup-i2c0-pins-default {
+		pinctrl-single,pins = <
+			J721E_WKUP_IOPAD(0x98, PIN_INPUT_PULLUP, 0) /* (F20) WKUP_I2C0_SCL */
+			J721E_WKUP_IOPAD(0x9c, PIN_INPUT_PULLUP, 0) /* (H21) WKUP_I2C0_SDA */
+		>;
+	};
+};
+
+&wkup_pmx3 {
+	/* wkup_pmx3 starts at 0x174 */
+	pmic_irq_pins_default: pmic-irq-pins-default {
+		pinctrl-single,pins = <
+			J721E_WKUP_IOPAD(0x1c, PIN_INPUT, 7) /* (E18) WKUP_GPIO0_84 */
+		>;
+	};
+};
+
 &main_pmx0 {
 	main_i2c0_pins_default: main-i2c0-pins-default {
 		pinctrl-single,pins = <
@@ -231,3 +250,154 @@ flash@0 {
 		cdns,read-delay = <4>;
 	};
 };
+
+&wkup_i2c0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&wkup_i2c0_pins_default>;
+	clock-frequency = <400000>;
+
+	tps659414: tps659414@48 {
+		compatible = "ti,tps6594";
+		reg = <0x48>;
+		ti,primary-pmic;
+		system-power-controller;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_irq_pins_default>;
+		interrupt-parent = <&wkup_gpio0>;
+		interrupts = <84 IRQ_TYPE_EDGE_FALLING>;
+
+		buck1-supply = <&vsys_3v3>;
+		buck2-supply = <&vsys_3v3>;
+		buck3-supply = <&vsys_3v3>;
+		buck4-supply = <&vsys_3v3>;
+		buck5-supply = <&vsys_3v3>;
+		ldo1-supply = <&vsys_3v3>;
+		ldo2-supply = <&vsys_3v3>;
+		ldo3-supply = <&vsys_3v3>;
+		ldo4-supply = <&vsys_3v3>;
+
+		regulators {
+			bucka1_reg: buck1 {
+				regulator-name = "vda_mcu_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			bucka2_reg: buck2 {
+				regulator-name = "vdd_mcuio_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			bucka3_reg: buck3 {
+				regulator-name = "vdd_mcu_0v85";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			bucka4_reg: buck4 {
+				regulator-name = "vdd_ddr_1v1";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			bucka5_reg: buck5 {
+				regulator-name = "vdd_phyio_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa1_reg: ldo1 {
+				regulator-name = "vdd1_lpddr4_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa2_reg: ldo2 {
+				regulator-name = "vda_dll_0v8";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa3_reg: ldo3 {
+				regulator-name = "vdd_wk_0v8";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa4_reg: ldo4 {
+				regulator-name = "vda_pll_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+
+	lp876441: lp876441@4c {
+		compatible = "ti,lp8764";
+		reg = <0x4c>;
+		system-power-controller;
+		interrupt-parent = <&wkup_gpio0>;
+		interrupts = <84 IRQ_TYPE_EDGE_FALLING>;
+
+		buck1-supply = <&vsys_3v3>;
+		buck2-supply = <&vsys_3v3>;
+		buck3-supply = <&vsys_3v3>;
+		buck4-supply = <&vsys_3v3>;
+
+		regulators: regulators {
+			buckb1_reg: buck1 {
+				/*VDD_CPU_AVS_REG*/
+				regulator-name = "vdd_cpu_avs";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1250000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			buckb2_reg: buck2 {
+				regulator-name = "vdd_ram_0v85";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buckb3_reg: buck3 {
+				regulator-name = "vdd_core_0v85";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buckb4_reg: buck4 {
+				regulator-name = "vdd_io_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+};
-- 
2.39.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

  reply	other threads:[~2023-03-29 14:30 UTC|newest]

Thread overview: 6+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2023-03-29 14:29 [PATCH v1 0/4] Add TPS6594 PMIC support on several boards Esteban Blanc
2023-03-29 14:29 ` Esteban Blanc [this message]
2023-03-29 14:29 ` [PATCH v1 2/4] arm64: dts: ti: k3-j721s2-som-p0: Add TP6594 family PMICs Esteban Blanc
2023-03-29 14:29 ` [PATCH v1 3/4] arm64: dts: ti: k3-am62a7-sk: Add support for TPS6593 PMIC Esteban Blanc
2023-03-29 14:29 ` [PATCH v1 4/4] arm64: dts: ti: k3-j721e-som-p0: Add TP6594 family PMICs Esteban Blanc
2023-03-30  3:00 ` [PATCH v1 0/4] Add TPS6594 PMIC support on several boards Nishanth Menon

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20230329142948.833800-2-eblanc@baylibre.com \
    --to=eblanc@baylibre.com \
    --cc=devicetree@vger.kernel.org \
    --cc=jneanne@baylibre.com \
    --cc=jpanis@baylibre.com \
    --cc=kristo@kernel.org \
    --cc=krzysztof.kozlowski+dt@linaro.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=nm@ti.com \
    --cc=robh+dt@kernel.org \
    --cc=sterzik@ti.com \
    --cc=u-kumar1@ti.com \
    --cc=vigneshr@ti.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox