[PATCH v2 1/2] ARM: dts: imx7d-sdb: Describe the SD card regulator

[PATCH v2 1/2] ARM: dts: imx7d-sdb: Describe the SD card regulator

[Fabio Estevam]

From: Fabio Estevam <festevam@denx.de>

Improve the devicetree description by adding the SD card regulator
that is controlled via GPIO5_2.

Signed-off-by: Fabio Estevam <festevam@denx.de>
---
Changes since v1:
- Put 'enable-active-high' right after 'gpio'. (Shawn)

 arch/arm/boot/dts/imx7d-sdb.dts | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/imx7d-sdb.dts b/arch/arm/boot/dts/imx7d-sdb.dts
index 25681c430393..c898d66e27ad 100644
--- a/arch/arm/boot/dts/imx7d-sdb.dts
+++ b/arch/arm/boot/dts/imx7d-sdb.dts
@@ -60,6 +60,17 @@ extended_io: gpio-expander@0 {
 		};
 	};
 
+	reg_sd1_vmmc: regulator-sd1-vmmc {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_SD1";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		startup-delay-us = <200000>;
+		off-on-delay-us = <20000>;
+	};
+
 	reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
 		compatible = "regulator-fixed";
 		regulator-name = "usb_otg1_vbus";
@@ -477,6 +488,7 @@ &usdhc1 {
 	pinctrl-0 = <&pinctrl_usdhc1>;
 	cd-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
 	wp-gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+	vmmc-supply = <&reg_sd1_vmmc>;
 	wakeup-source;
 	keep-power-in-suspend;
 	status = "okay";
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 2/2] ARM: dts: imx7d-sdb: Allow UHS modes

[Fabio Estevam]

From: Fabio Estevam <festevam@denx.de>

Describe the SD1_VSELECT pad, which is necessary to allow UHS modes.

Also, to support higher SD card speed modes, describe the 100MHz and
200MHz SD card pinctrl entries.

Suggested-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
---
Changes since v1:
- None

 arch/arm/boot/dts/imx7d-sdb.dts | 40 ++++++++++++++++++++++++++++-----
 1 file changed, 35 insertions(+), 5 deletions(-)

diff --git a/arch/arm/boot/dts/imx7d-sdb.dts b/arch/arm/boot/dts/imx7d-sdb.dts
index 6e45f1154611..98e77fdfc27a 100644
--- a/arch/arm/boot/dts/imx7d-sdb.dts
+++ b/arch/arm/boot/dts/imx7d-sdb.dts
@@ -484,8 +484,10 @@ &usbotg2 {
 };
 
 &usdhc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>, <&pinctrl_usdhc1_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>, <&pinctrl_usdhc1_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>, <&pinctrl_usdhc1_gpio>;
 	cd-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
 	wp-gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
 	vmmc-supply = <&reg_sd1_vmmc>;
@@ -743,6 +745,15 @@ MX7D_PAD_ECSPI1_MISO__UART6_DCE_RTS	0x79
 			>;
 		};
 
+		pinctrl_usdhc1_gpio: usdhc1_gpiogrp {
+			fsl,pins = <
+				MX7D_PAD_SD1_CD_B__GPIO5_IO0		0x59 /* CD */
+				MX7D_PAD_SD1_WP__GPIO5_IO1		0x59 /* WP */
+				MX7D_PAD_SD1_RESET_B__GPIO5_IO2		0x59 /* vmmc */
+				MX7D_PAD_GPIO1_IO08__SD1_VSELECT	0x59 /* VSELECT */
+			>;
+		};
+
 		pinctrl_usdhc1: usdhc1grp {
 			fsl,pins = <
 				MX7D_PAD_SD1_CMD__SD1_CMD		0x59
@@ -751,9 +762,28 @@ MX7D_PAD_SD1_DATA0__SD1_DATA0		0x59
 				MX7D_PAD_SD1_DATA1__SD1_DATA1		0x59
 				MX7D_PAD_SD1_DATA2__SD1_DATA2		0x59
 				MX7D_PAD_SD1_DATA3__SD1_DATA3		0x59
-				MX7D_PAD_SD1_CD_B__GPIO5_IO0		0x59 /* CD */
-				MX7D_PAD_SD1_WP__GPIO5_IO1		0x59 /* WP */
-				MX7D_PAD_SD1_RESET_B__GPIO5_IO2		0x59 /* vmmc */
+			>;
+		};
+
+		pinctrl_usdhc1_100mhz: usdhc1grp_100mhz {
+			fsl,pins = <
+				MX7D_PAD_SD1_CMD__SD1_CMD		0x5a
+				MX7D_PAD_SD1_CLK__SD1_CLK		0x1a
+				MX7D_PAD_SD1_DATA0__SD1_DATA0		0x5a
+				MX7D_PAD_SD1_DATA1__SD1_DATA1		0x5a
+				MX7D_PAD_SD1_DATA2__SD1_DATA2		0x5a
+				MX7D_PAD_SD1_DATA3__SD1_DATA3		0x5a
+			>;
+		};
+
+		pinctrl_usdhc1_200mhz: usdhc1grp_200mhz {
+			fsl,pins = <
+				MX7D_PAD_SD1_CMD__SD1_CMD		0x5b
+				MX7D_PAD_SD1_CLK__SD1_CLK		0x1b
+				MX7D_PAD_SD1_DATA0__SD1_DATA0		0x5b
+				MX7D_PAD_SD1_DATA1__SD1_DATA1		0x5b
+				MX7D_PAD_SD1_DATA2__SD1_DATA2		0x5b
+				MX7D_PAD_SD1_DATA3__SD1_DATA3		0x5b
 			>;
 		};
 
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v2 1/2] ARM: dts: imx7d-sdb: Describe the SD card regulator

[Shawn Guo]

On Sat, May 27, 2023 at 01:06:33PM -0300, Fabio Estevam wrote:
> From: Fabio Estevam <festevam@denx.de>
> 
> Improve the devicetree description by adding the SD card regulator
> that is controlled via GPIO5_2.
> 
> Signed-off-by: Fabio Estevam <festevam@denx.de>

Applied both, thanks!

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel