From: Ulf Hansson <ulf.hansson@linaro.org>
To: Sudeep Holla <sudeep.holla@arm.com>,
Cristian Marussi <cristian.marussi@arm.com>,
Viresh Kumar <vireshk@kernel.org>, Nishanth Menon <nm@ti.com>,
Stephen Boyd <sboyd@kernel.org>
Cc: Nikunj Kela <nkela@quicinc.com>,
Prasad Sodagudi <psodagud@quicinc.com>,
Alexandre Torgue <alexandre.torgue@foss.st.com>,
Ulf Hansson <ulf.hansson@linaro.org>,
linux-pm@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org
Subject: [PATCH 08/16] PM: domains: Allow genpd providers to manage OPP tables directly by its FW
Date: Wed, 7 Jun 2023 14:46:20 +0200 [thread overview]
Message-ID: <20230607124628.157465-9-ulf.hansson@linaro.org> (raw)
In-Reply-To: <20230607124628.157465-1-ulf.hansson@linaro.org>
In some cases the OPP tables aren't specified in device tree, but rather
encoded in the FW. To allow a genpd provider to specify them dynamically
instead, let's add a new genpd flag, GENPD_FLAG_OPP_TABLE_FW.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
---
drivers/base/power/domain.c | 11 ++++++-----
include/linux/pm_domain.h | 5 +++++
2 files changed, 11 insertions(+), 5 deletions(-)
diff --git a/drivers/base/power/domain.c b/drivers/base/power/domain.c
index 32084e38b73d..cb35c040216a 100644
--- a/drivers/base/power/domain.c
+++ b/drivers/base/power/domain.c
@@ -130,6 +130,7 @@ static const struct genpd_lock_ops genpd_spin_ops = {
#define genpd_is_active_wakeup(genpd) (genpd->flags & GENPD_FLAG_ACTIVE_WAKEUP)
#define genpd_is_cpu_domain(genpd) (genpd->flags & GENPD_FLAG_CPU_DOMAIN)
#define genpd_is_rpm_always_on(genpd) (genpd->flags & GENPD_FLAG_RPM_ALWAYS_ON)
+#define genpd_is_opp_table_fw(genpd) (genpd->flags & GENPD_FLAG_OPP_TABLE_FW)
static inline bool irq_safe_dev_in_sleep_domain(struct device *dev,
const struct generic_pm_domain *genpd)
@@ -2328,7 +2329,7 @@ int of_genpd_add_provider_simple(struct device_node *np,
genpd->dev.of_node = np;
/* Parse genpd OPP table */
- if (genpd->set_performance_state) {
+ if (!genpd_is_opp_table_fw(genpd) && genpd->set_performance_state) {
ret = dev_pm_opp_of_add_table(&genpd->dev);
if (ret)
return dev_err_probe(&genpd->dev, ret, "Failed to add OPP table\n");
@@ -2343,7 +2344,7 @@ int of_genpd_add_provider_simple(struct device_node *np,
ret = genpd_add_provider(np, genpd_xlate_simple, genpd);
if (ret) {
- if (genpd->set_performance_state) {
+ if (!genpd_is_opp_table_fw(genpd) && genpd->set_performance_state) {
dev_pm_opp_put_opp_table(genpd->opp_table);
dev_pm_opp_of_remove_table(&genpd->dev);
}
@@ -2387,7 +2388,7 @@ int of_genpd_add_provider_onecell(struct device_node *np,
genpd->dev.of_node = np;
/* Parse genpd OPP table */
- if (genpd->set_performance_state) {
+ if (!genpd_is_opp_table_fw(genpd) && genpd->set_performance_state) {
ret = dev_pm_opp_of_add_table_indexed(&genpd->dev, i);
if (ret) {
dev_err_probe(&genpd->dev, ret,
@@ -2423,7 +2424,7 @@ int of_genpd_add_provider_onecell(struct device_node *np,
genpd->provider = NULL;
genpd->has_provider = false;
- if (genpd->set_performance_state) {
+ if (!genpd_is_opp_table_fw(genpd) && genpd->set_performance_state) {
dev_pm_opp_put_opp_table(genpd->opp_table);
dev_pm_opp_of_remove_table(&genpd->dev);
}
@@ -2455,7 +2456,7 @@ void of_genpd_del_provider(struct device_node *np)
if (gpd->provider == &np->fwnode) {
gpd->has_provider = false;
- if (!gpd->set_performance_state)
+ if (genpd_is_opp_table_fw(gpd) || !gpd->set_performance_state)
continue;
dev_pm_opp_put_opp_table(gpd->opp_table);
diff --git a/include/linux/pm_domain.h b/include/linux/pm_domain.h
index f776fb93eaa0..05ad8cefdff1 100644
--- a/include/linux/pm_domain.h
+++ b/include/linux/pm_domain.h
@@ -61,6 +61,10 @@
* GENPD_FLAG_MIN_RESIDENCY: Enable the genpd governor to consider its
* components' next wakeup when determining the
* optimal idle state.
+ *
+ * GENPD_FLAG_OPP_TABLE_FW: The genpd provider supports performance states,
+ * but its corresponding OPP tables are not
+ * described in DT, but are given directly by FW.
*/
#define GENPD_FLAG_PM_CLK (1U << 0)
#define GENPD_FLAG_IRQ_SAFE (1U << 1)
@@ -69,6 +73,7 @@
#define GENPD_FLAG_CPU_DOMAIN (1U << 4)
#define GENPD_FLAG_RPM_ALWAYS_ON (1U << 5)
#define GENPD_FLAG_MIN_RESIDENCY (1U << 6)
+#define GENPD_FLAG_OPP_TABLE_FW (1U << 7)
enum gpd_status {
GENPD_STATE_ON = 0, /* PM domain is on */
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2023-06-07 14:01 UTC|newest]
Thread overview: 37+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-06-07 12:46 [PATCH 00/16] arm_scmi/opp/dvfs: Add generic performance scaling support Ulf Hansson
2023-06-07 12:46 ` [PATCH 01/16] firmware: arm_scmi: Extend perf protocol ops to get number of domains Ulf Hansson
2023-06-07 12:46 ` [PATCH 02/16] firmware: arm_scmi: Extend perf protocol ops to get the name of a domain Ulf Hansson
2023-06-07 12:46 ` [PATCH 03/16] firmware: arm_scmi: Extend perf protocol ops to inform of set level support Ulf Hansson
2023-06-07 12:46 ` [PATCH 04/16] cpufreq: scmi: Prepare to move OF parsing of domain-id to cpufreq Ulf Hansson
2023-06-07 12:46 ` [PATCH 05/16] firmware: arm_scmi: Align perf ops to use domain-id as in-parameter Ulf Hansson
2023-06-07 12:46 ` [PATCH 06/16] firmware: arm_scmi: Drop redundant ->device_domain_id() from perf ops Ulf Hansson
2023-06-07 12:46 ` [PATCH 07/16] cpufreq: scmi: Avoid one OF parsing in scmi_get_sharing_cpus() Ulf Hansson
2023-06-07 12:46 ` Ulf Hansson [this message]
2023-06-07 12:46 ` [PATCH 09/16] dt-bindings: firmware: arm,scmi: Extend bindings for protocol@13 Ulf Hansson
2023-06-14 23:00 ` Rob Herring
2023-06-15 9:10 ` Ulf Hansson
2023-07-14 17:14 ` Rob Herring
2023-07-15 12:35 ` Ulf Hansson
2023-06-15 8:44 ` Sudeep Holla
2023-06-15 9:39 ` Ulf Hansson
2023-06-15 13:30 ` Sudeep Holla
2023-06-16 11:48 ` Ulf Hansson
2023-06-07 12:46 ` [PATCH 10/16] firmware: arm_scmi: Add the SCMI performance domain Ulf Hansson
2023-06-07 12:46 ` [PATCH 11/16] OPP: Add dev_pm_opp_add_dynamic() to allow more flexibility Ulf Hansson
2023-06-08 5:29 ` Viresh Kumar
2023-06-08 8:59 ` Ulf Hansson
2023-06-08 9:22 ` Viresh Kumar
2023-06-08 9:40 ` Ulf Hansson
2023-06-07 12:46 ` [PATCH 12/16] OPP: Extend dev_pm_opp_data with performance level Ulf Hansson
2023-06-07 12:46 ` [PATCH 13/16] OPP: Extend dev_pm_opp_data with OPP provider support Ulf Hansson
2023-06-08 5:34 ` Viresh Kumar
2023-06-08 9:37 ` Ulf Hansson
2023-06-08 10:45 ` Viresh Kumar
2023-06-08 11:45 ` Ulf Hansson
2023-06-09 5:10 ` Viresh Kumar
2023-06-09 10:59 ` Ulf Hansson
2023-06-07 12:46 ` [PATCH 14/16] firmware: arm_scmi: Simplify error path in scmi_dvfs_device_opps_add() Ulf Hansson
2023-06-07 12:46 ` [PATCH 15/16] firmware: arm_scmi: Extend perf support with OPP from genpd providers Ulf Hansson
2023-06-07 12:46 ` [PATCH 16/16] firmware: arm_scmi: Add generic OPP support to the SCMI performance domain Ulf Hansson
2023-06-07 14:43 ` [PATCH 00/16] arm_scmi/opp/dvfs: Add generic performance scaling support Cristian Marussi
2023-06-08 9:53 ` Ulf Hansson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230607124628.157465-9-ulf.hansson@linaro.org \
--to=ulf.hansson@linaro.org \
--cc=alexandre.torgue@foss.st.com \
--cc=cristian.marussi@arm.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pm@vger.kernel.org \
--cc=nkela@quicinc.com \
--cc=nm@ti.com \
--cc=psodagud@quicinc.com \
--cc=sboyd@kernel.org \
--cc=sudeep.holla@arm.com \
--cc=vireshk@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).