[PATCH v3 7/8] arm64: dts: ti: k3-am625-beagleplay: Add HDMI support

[Aradhya Bhatia <a-bhatia1@ti.com>]

From: Nishanth Menon <nm@ti.com>

Add support for HDMI audio and video output.

Beagleplay uses mcasp1 for its audio output, and ITE-IT66121 as its
on-board HDMI encoder.

The HDMI transmitter uses the DPI output from the VP2 of DSS as its
source and forwards the HDMI signals to the on-board Type-A HDMI
connector.

Signed-off-by: Nishanth Menon <nm@ti.com>
[a-bhatia1: Edit sound node properties]
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
---
 .../arm64/boot/dts/ti/k3-am625-beagleplay.dts | 119 ++++++++++++++++++
 1 file changed, 119 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts b/arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts
index 63893d868623..93da57949b07 100644
--- a/arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts
+++ b/arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts
@@ -192,6 +192,34 @@ usr: button-usr {
 
 	};
 
+	hdmi0: connector {
+		compatible = "hdmi-connector";
+		label = "hdmi";
+		type = "a";
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&it66121hdmitx_out>;
+			};
+		};
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "it66121 HDMI";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,bitclock-master = <&hdmi_dailink_master>;
+		simple-audio-card,frame-master = <&hdmi_dailink_master>;
+
+		hdmi_dailink_master: simple-audio-card,cpu {
+			sound-dai = <&mcasp1>;
+			system-clock-direction-out;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&it66121hdmitx>;
+		};
+	};
+
 	/* Workaround for errata i2329 - just use mdio bitbang */
 	mdio0: mdio {
 		compatible = "virtual,mdio-gpio";
@@ -480,6 +508,24 @@ AM62X_IOPAD(0x02a8, PIN_OUTPUT, 0) /* (AE4) OLDI0_CLK1N */
 			AM62X_IOPAD(0x02a4, PIN_OUTPUT, 0) /* (AD5) OLDI0_CLK1P */
 		>;
 	};
+
+	hdmi_gpio_pins_default: hdmi-gpio-default-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x0094, PIN_INPUT_PULLUP | PIN_DEBOUNCE_CONF6, 7) /* (N20) GPMC0_BE1n.GPIO0_36 */
+			AM62X_IOPAD(0x0054, PIN_OUTPUT_PULLUP, 7) /* (P21) GPMC0_AD6.GPIO0_21 */
+		>;
+	};
+
+	mcasp_hdmi_pins_default: mcasp-hdmi-default-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x0090, PIN_INPUT, 2) /* (M24) GPMC0_BE0n_CLE.MCASP1_ACLKX */
+			AM62X_IOPAD(0x0098, PIN_INPUT, 2) /* (U23) GPMC0_WAIT0.MCASP1_AFSX */
+			AM62X_IOPAD(0x008c, PIN_OUTPUT, 2) /* (L25) GPMC0_WEn.MCASP1_AXR0 */
+			AM62X_IOPAD(0x0088, PIN_INPUT, 2) /* (L24) GPMC0_OEn_REn.MCASP1_AXR1 */
+			AM62X_IOPAD(0x0084, PIN_INPUT, 2) /* (L23) GPMC0_ADVn_ALE.MCASP1_AXR2 */
+			AM62X_IOPAD(0x007c, PIN_INPUT, 2) /* (P25) GPMC0_CLK.MCASP1_AXR3 */
+		>;
+	};
 };
 
 &mcu_pmx0 {
@@ -728,6 +774,46 @@ &main_i2c2 {
 	pinctrl-0 = <&i2c2_1v8_pins_default>;
 	clock-frequency = <100000>;
 	status = "okay";
+
+	it66121hdmitx: hdmitx@4c {
+		compatible = "ite,it66121";
+		pinctrl-names = "default";
+		pinctrl-0 = <&hdmi_gpio_pins_default>;
+		reg = <0x4c>;
+
+		#sound-dai-cells = <0>;
+
+		interrupt-parent = <&main_gpio0>;
+		interrupts = <36 IRQ_TYPE_EDGE_FALLING>;
+
+		vcn33-supply = <&vdd_3v3>;
+		vcn18-supply = <&buck2_reg>;
+		vrf12-supply = <&buck3_reg>;
+
+		reset-gpios = <&main_gpio0 21 GPIO_ACTIVE_LOW>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				it66121hdmitx_in: endpoint {
+					bus-width = <24>;
+					remote-endpoint = <&dpi1_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				it66121hdmitx_out: endpoint {
+					remote-endpoint = <&hdmi_connector_in>;
+				};
+			};
+		};
+	};
 };
 
 &main_i2c3 {
@@ -819,3 +905,36 @@ &dss {
 	pinctrl-names = "default";
 	pinctrl-0 = <&dss0_pins_default &oldi0_pins_default>;
 };
+
+&dss_ports {
+	/* VP2: DPI Output */
+	port@1 {
+		reg = <1>;
+
+		dpi1_out: endpoint {
+			remote-endpoint = <&it66121hdmitx_in>;
+		};
+	};
+};
+
+&mcasp1 {
+	status = "okay";
+	#sound-dai-cells = <0>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcasp_hdmi_pins_default>;
+
+	auxclk-fs-ratio = <2177>;
+
+	op-mode = <0>;          /* MCASP_IIS_MODE */
+	tdm-slots = <2>;
+
+	serial-dir = <  /* 0: INACTIVE, 1: TX, 2: RX */
+	       1 0 0 0
+	       0 0 0 0
+	       0 0 0 0
+	       0 0 0 0
+	>;
+	tx-num-evt = <32>;
+	rx-num-evt = <32>;
+};
-- 
2.40.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel