* [PATCH 2/4] arm64: dts: imx8mp: Fix property indent on DH i.MX8M Plus DHCOM PDK3
2023-08-31 18:20 [PATCH 1/4] arm64: dts: imx8mp: Describe VDD_ARM run and standby voltage for DH i.MX8M Plus DHCOM SoM Marek Vasut
@ 2023-08-31 18:20 ` Marek Vasut
2023-08-31 18:20 ` [PATCH 3/4] arm64: dts: imx8mp: Switch WiFI enable signal to mmc-pwrseq-simple on i.MX8MP DHCOM SoM Marek Vasut
` (3 subsequent siblings)
4 siblings, 0 replies; 8+ messages in thread
From: Marek Vasut @ 2023-08-31 18:20 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Marek Vasut, Conor Dooley, Fabio Estevam, Frieder Schrempf,
Geert Uytterhoeven, Krzysztof Kozlowski, Magnus Damm,
NXP Linux Team, Peng Fan, Pengutronix Kernel Team, Rob Herring,
Sascha Hauer, Shawn Guo, devicetree
Fix indent to use tab indent. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
---
Cc: Conor Dooley <conor+dt@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Frieder Schrempf <frieder.schrempf@kontron.de>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
---
arch/arm64/boot/dts/freescale/imx8mp-dhcom-pdk3.dts | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-dhcom-pdk3.dts b/arch/arm64/boot/dts/freescale/imx8mp-dhcom-pdk3.dts
index 31d85d5871c91..5d1eb3767bd34 100644
--- a/arch/arm64/boot/dts/freescale/imx8mp-dhcom-pdk3.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mp-dhcom-pdk3.dts
@@ -225,10 +225,10 @@ ptn5150_out_ep: endpoint {
};
power-sensor@40 {
- compatible = "ti,ina238";
- reg = <0x40>;
- shunt-resistor = <20000>; /* 0.02 R */
- ti,shunt-gain = <1>; /* Drop cca. 40mV */
+ compatible = "ti,ina238";
+ reg = <0x40>;
+ shunt-resistor = <20000>; /* 0.02 R */
+ ti,shunt-gain = <1>; /* Drop cca. 40mV */
};
eeprom_board: eeprom@54 {
--
2.40.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 8+ messages in thread* [PATCH 3/4] arm64: dts: imx8mp: Switch WiFI enable signal to mmc-pwrseq-simple on i.MX8MP DHCOM SoM
2023-08-31 18:20 [PATCH 1/4] arm64: dts: imx8mp: Describe VDD_ARM run and standby voltage for DH i.MX8M Plus DHCOM SoM Marek Vasut
2023-08-31 18:20 ` [PATCH 2/4] arm64: dts: imx8mp: Fix property indent on DH i.MX8M Plus DHCOM PDK3 Marek Vasut
@ 2023-08-31 18:20 ` Marek Vasut
2023-08-31 18:20 ` [PATCH 4/4] arm64: dts: imx8mp: Add UART1 and RTC wake up source on DH i.MX8M Plus " Marek Vasut
` (2 subsequent siblings)
4 siblings, 0 replies; 8+ messages in thread
From: Marek Vasut @ 2023-08-31 18:20 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Marek Vasut, Conor Dooley, Fabio Estevam, Frieder Schrempf,
Geert Uytterhoeven, Krzysztof Kozlowski, Magnus Damm,
NXP Linux Team, Peng Fan, Pengutronix Kernel Team, Rob Herring,
Sascha Hauer, Shawn Guo, devicetree
The reset-gpio is connected to WL_REG_EN signal of the WiFi MAC, the
mmc-pwrseq-simple driver is better suited to operate this signal as
it is tied to the slot instead of the MAC, and it can enable the MAC
before the brcmfmac driver binds to it. Make use of the MMC power
sequencer.
Signed-off-by: Marek Vasut <marex@denx.de>
---
Cc: Conor Dooley <conor+dt@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Frieder Schrempf <frieder.schrempf@kontron.de>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
---
arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi | 7 ++++++-
1 file changed, 6 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi
index 1644b56c3953d..df43741d04bb9 100644
--- a/arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi
@@ -57,6 +57,11 @@ reg_vdd_3p3v_awo: regulator-vdd-3p3v-awo { /* VDD_3V3_AWO */
regulator-max-microvolt = <3300000>;
regulator-name = "VDD_3P3V_AWO";
};
+
+ wlan_pwrseq: wifi-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
+ };
};
&A53_0 {
@@ -543,6 +548,7 @@ &usdhc1 {
pinctrl-0 = <&pinctrl_usdhc1>;
pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+ mmc-pwrseq = <&wlan_pwrseq>;
vmmc-supply = <&buck4>;
bus-width = <4>;
non-removable;
@@ -561,7 +567,6 @@ brcmf: bcrmf@1 { /* muRata 2AE */
* connected to the SoC, but can be connected on to
* SoC pin on the carrier board.
*/
- reset-gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
};
};
--
2.40.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 8+ messages in thread* [PATCH 4/4] arm64: dts: imx8mp: Add UART1 and RTC wake up source on DH i.MX8M Plus DHCOM SoM
2023-08-31 18:20 [PATCH 1/4] arm64: dts: imx8mp: Describe VDD_ARM run and standby voltage for DH i.MX8M Plus DHCOM SoM Marek Vasut
2023-08-31 18:20 ` [PATCH 2/4] arm64: dts: imx8mp: Fix property indent on DH i.MX8M Plus DHCOM PDK3 Marek Vasut
2023-08-31 18:20 ` [PATCH 3/4] arm64: dts: imx8mp: Switch WiFI enable signal to mmc-pwrseq-simple on i.MX8MP DHCOM SoM Marek Vasut
@ 2023-08-31 18:20 ` Marek Vasut
2023-09-07 15:45 ` [PATCH 1/4] arm64: dts: imx8mp: Describe VDD_ARM run and standby voltage for " Marco Felsch
2023-10-12 10:17 ` Shawn Guo
4 siblings, 0 replies; 8+ messages in thread
From: Marek Vasut @ 2023-08-31 18:20 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Marek Vasut, Conor Dooley, Fabio Estevam, Frieder Schrempf,
Geert Uytterhoeven, Krzysztof Kozlowski, Magnus Damm,
NXP Linux Team, Peng Fan, Pengutronix Kernel Team, Rob Herring,
Sascha Hauer, Shawn Guo, devicetree
Turn Console UART1 and dedicated RTC into wake up sources, to make
it possible to wake on UART and RTC alarm.
Signed-off-by: Marek Vasut <marex@denx.de>
---
Cc: Conor Dooley <conor+dt@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Frieder Schrempf <frieder.schrempf@kontron.de>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
---
arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi
index df43741d04bb9..4582a0bbe3726 100644
--- a/arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi
@@ -414,6 +414,7 @@ rv3032: rtc@51 {
interrupts-extended = <&gpio5 5 IRQ_TYPE_LEVEL_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_rtc>;
+ wakeup-source;
};
eeprom1: eeprom@53 { /* EEPROM with FEC MAC address */
@@ -470,6 +471,7 @@ &uart1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
status = "okay";
+ wakeup-source;
};
&uart2 {
--
2.40.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 8+ messages in thread* Re: [PATCH 1/4] arm64: dts: imx8mp: Describe VDD_ARM run and standby voltage for DH i.MX8M Plus DHCOM SoM
2023-08-31 18:20 [PATCH 1/4] arm64: dts: imx8mp: Describe VDD_ARM run and standby voltage for DH i.MX8M Plus DHCOM SoM Marek Vasut
` (2 preceding siblings ...)
2023-08-31 18:20 ` [PATCH 4/4] arm64: dts: imx8mp: Add UART1 and RTC wake up source on DH i.MX8M Plus " Marek Vasut
@ 2023-09-07 15:45 ` Marco Felsch
2023-09-07 18:25 ` Marek Vasut
2023-10-12 10:17 ` Shawn Guo
4 siblings, 1 reply; 8+ messages in thread
From: Marco Felsch @ 2023-09-07 15:45 UTC (permalink / raw)
To: Marek Vasut
Cc: linux-arm-kernel, devicetree, Conor Dooley,
Pengutronix Kernel Team, Geert Uytterhoeven, Shawn Guo,
Sascha Hauer, Magnus Damm, Peng Fan, Frieder Schrempf,
Rob Herring, NXP Linux Team, Krzysztof Kozlowski, Fabio Estevam
Hi Marek,
On 23-08-31, Marek Vasut wrote:
> Describe VDD_ARM (BUCK2) run and standby voltage in DT.
>
> Signed-off-by: Marek Vasut <marex@denx.de>
> ---
> Cc: Conor Dooley <conor+dt@kernel.org>
> Cc: Fabio Estevam <festevam@gmail.com>
> Cc: Frieder Schrempf <frieder.schrempf@kontron.de>
> Cc: Geert Uytterhoeven <geert+renesas@glider.be>
> Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
> Cc: Magnus Damm <magnus.damm@gmail.com>
> Cc: Marek Vasut <marex@denx.de>
> Cc: NXP Linux Team <linux-imx@nxp.com>
> Cc: Peng Fan <peng.fan@nxp.com>
> Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
> Cc: Rob Herring <robh+dt@kernel.org>
> Cc: Sascha Hauer <s.hauer@pengutronix.de>
> Cc: Shawn Guo <shawnguo@kernel.org>
> Cc: devicetree@vger.kernel.org
> Cc: linux-arm-kernel@lists.infradead.org
> ---
> arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi | 2 ++
> 1 file changed, 2 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi
> index cb1953d14aa90..1644b56c3953d 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi
> +++ b/arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi
> @@ -293,6 +293,8 @@ buck1: BUCK1 { /* VDD_SOC (dual-phase with BUCK3) */
> };
>
> buck2: BUCK2 { /* VDD_ARM */
> + nxp,dvs-run-voltage = <950000>;
Why do we need to set the "nxp,dvs-run-voltage"? If I read the driver
correctly, then nxp,dvs-run-voltage and regulator-min/max-microvolt are
touching the same register.
Regards,
Marco
> + nxp,dvs-standby-voltage = <850000>;
> regulator-min-microvolt = <850000>;
> regulator-max-microvolt = <1000000>;
> regulator-ramp-delay = <3125>;
> --
> 2.40.1
>
>
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 8+ messages in thread* Re: [PATCH 1/4] arm64: dts: imx8mp: Describe VDD_ARM run and standby voltage for DH i.MX8M Plus DHCOM SoM
2023-09-07 15:45 ` [PATCH 1/4] arm64: dts: imx8mp: Describe VDD_ARM run and standby voltage for " Marco Felsch
@ 2023-09-07 18:25 ` Marek Vasut
2023-09-08 7:34 ` Marco Felsch
0 siblings, 1 reply; 8+ messages in thread
From: Marek Vasut @ 2023-09-07 18:25 UTC (permalink / raw)
To: Marco Felsch
Cc: linux-arm-kernel, devicetree, Conor Dooley,
Pengutronix Kernel Team, Geert Uytterhoeven, Shawn Guo,
Sascha Hauer, Magnus Damm, Peng Fan, Frieder Schrempf,
Rob Herring, NXP Linux Team, Krzysztof Kozlowski, Fabio Estevam
On 9/7/23 17:45, Marco Felsch wrote:
> Hi Marek,
Hi,
> On 23-08-31, Marek Vasut wrote:
>> Describe VDD_ARM (BUCK2) run and standby voltage in DT.
>>
>> Signed-off-by: Marek Vasut <marex@denx.de>
>> ---
>> Cc: Conor Dooley <conor+dt@kernel.org>
>> Cc: Fabio Estevam <festevam@gmail.com>
>> Cc: Frieder Schrempf <frieder.schrempf@kontron.de>
>> Cc: Geert Uytterhoeven <geert+renesas@glider.be>
>> Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
>> Cc: Magnus Damm <magnus.damm@gmail.com>
>> Cc: Marek Vasut <marex@denx.de>
>> Cc: NXP Linux Team <linux-imx@nxp.com>
>> Cc: Peng Fan <peng.fan@nxp.com>
>> Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
>> Cc: Rob Herring <robh+dt@kernel.org>
>> Cc: Sascha Hauer <s.hauer@pengutronix.de>
>> Cc: Shawn Guo <shawnguo@kernel.org>
>> Cc: devicetree@vger.kernel.org
>> Cc: linux-arm-kernel@lists.infradead.org
>> ---
>> arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi | 2 ++
>> 1 file changed, 2 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi
>> index cb1953d14aa90..1644b56c3953d 100644
>> --- a/arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi
>> +++ b/arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi
>> @@ -293,6 +293,8 @@ buck1: BUCK1 { /* VDD_SOC (dual-phase with BUCK3) */
>> };
>>
>> buck2: BUCK2 { /* VDD_ARM */
>> + nxp,dvs-run-voltage = <950000>;
>
> Why do we need to set the "nxp,dvs-run-voltage"? If I read the driver
> correctly, then nxp,dvs-run-voltage and regulator-min/max-microvolt are
> touching the same register.
My understanding is that the nxp,dvs-run-voltage selects the default
regulator voltage which is configured early on once the regulator is
detected in DT (see of_parse_cb callback in the PCA9450 regulator
driver) and may be higher than regulator-min-microvolt, while later on
DVFS can adjust the regulator in range of regulator-min-microvolt to
regulator-max-microvolt .
>> + nxp,dvs-standby-voltage = <850000>;
>> regulator-min-microvolt = <850000>;
>> regulator-max-microvolt = <1000000>;
[...]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 8+ messages in thread* Re: [PATCH 1/4] arm64: dts: imx8mp: Describe VDD_ARM run and standby voltage for DH i.MX8M Plus DHCOM SoM
2023-09-07 18:25 ` Marek Vasut
@ 2023-09-08 7:34 ` Marco Felsch
0 siblings, 0 replies; 8+ messages in thread
From: Marco Felsch @ 2023-09-08 7:34 UTC (permalink / raw)
To: Marek Vasut
Cc: linux-arm-kernel, devicetree, Conor Dooley,
Pengutronix Kernel Team, Geert Uytterhoeven, Shawn Guo,
Sascha Hauer, Magnus Damm, Peng Fan, Frieder Schrempf,
Rob Herring, NXP Linux Team, Krzysztof Kozlowski, Fabio Estevam
On 23-09-07, Marek Vasut wrote:
> On 9/7/23 17:45, Marco Felsch wrote:
> > Hi Marek,
>
> Hi,
>
> > On 23-08-31, Marek Vasut wrote:
> > > Describe VDD_ARM (BUCK2) run and standby voltage in DT.
> > >
> > > Signed-off-by: Marek Vasut <marex@denx.de>
> > > ---
> > > Cc: Conor Dooley <conor+dt@kernel.org>
> > > Cc: Fabio Estevam <festevam@gmail.com>
> > > Cc: Frieder Schrempf <frieder.schrempf@kontron.de>
> > > Cc: Geert Uytterhoeven <geert+renesas@glider.be>
> > > Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
> > > Cc: Magnus Damm <magnus.damm@gmail.com>
> > > Cc: Marek Vasut <marex@denx.de>
> > > Cc: NXP Linux Team <linux-imx@nxp.com>
> > > Cc: Peng Fan <peng.fan@nxp.com>
> > > Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
> > > Cc: Rob Herring <robh+dt@kernel.org>
> > > Cc: Sascha Hauer <s.hauer@pengutronix.de>
> > > Cc: Shawn Guo <shawnguo@kernel.org>
> > > Cc: devicetree@vger.kernel.org
> > > Cc: linux-arm-kernel@lists.infradead.org
> > > ---
> > > arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi | 2 ++
> > > 1 file changed, 2 insertions(+)
> > >
> > > diff --git a/arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi
> > > index cb1953d14aa90..1644b56c3953d 100644
> > > --- a/arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi
> > > +++ b/arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi
> > > @@ -293,6 +293,8 @@ buck1: BUCK1 { /* VDD_SOC (dual-phase with BUCK3) */
> > > };
> > > buck2: BUCK2 { /* VDD_ARM */
> > > + nxp,dvs-run-voltage = <950000>;
> >
> > Why do we need to set the "nxp,dvs-run-voltage"? If I read the driver
> > correctly, then nxp,dvs-run-voltage and regulator-min/max-microvolt are
> > touching the same register.
>
> My understanding is that the nxp,dvs-run-voltage selects the default
> regulator voltage which is configured early on once the regulator is
> detected in DT (see of_parse_cb callback in the PCA9450 regulator driver)
> and may be higher than regulator-min-microvolt, while later on DVFS can
> adjust the regulator in range of regulator-min-microvolt to
> regulator-max-microvolt .
Right, albeit I think that the bootloader already did the
initialization once. Anyway the change lgtm:
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
> > > + nxp,dvs-standby-voltage = <850000>;
> > > regulator-min-microvolt = <850000>;
> > > regulator-max-microvolt = <1000000>;
>
> [...]
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH 1/4] arm64: dts: imx8mp: Describe VDD_ARM run and standby voltage for DH i.MX8M Plus DHCOM SoM
2023-08-31 18:20 [PATCH 1/4] arm64: dts: imx8mp: Describe VDD_ARM run and standby voltage for DH i.MX8M Plus DHCOM SoM Marek Vasut
` (3 preceding siblings ...)
2023-09-07 15:45 ` [PATCH 1/4] arm64: dts: imx8mp: Describe VDD_ARM run and standby voltage for " Marco Felsch
@ 2023-10-12 10:17 ` Shawn Guo
4 siblings, 0 replies; 8+ messages in thread
From: Shawn Guo @ 2023-10-12 10:17 UTC (permalink / raw)
To: Marek Vasut
Cc: linux-arm-kernel, Conor Dooley, Fabio Estevam, Frieder Schrempf,
Geert Uytterhoeven, Krzysztof Kozlowski, Magnus Damm,
NXP Linux Team, Peng Fan, Pengutronix Kernel Team, Rob Herring,
Sascha Hauer, devicetree
On Thu, Aug 31, 2023 at 08:20:17PM +0200, Marek Vasut wrote:
> Describe VDD_ARM (BUCK2) run and standby voltage in DT.
>
> Signed-off-by: Marek Vasut <marex@denx.de>
Applied all, thanks!
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 8+ messages in thread