[PATCH RESEND v3 0/3] regulator: mt6358: Remove bogus regulators and improvements

[PATCH RESEND v3 0/3] regulator: mt6358: Remove bogus regulators and improvements

[Chen-Yu Tsai]

Hi,

This seems to have fallen through the cracks, so I'm resending with tags
collected and patches rebased onto next-20230925. The diffs remain the
same.

This is v3 of the remainder of the MT6358 regulator driver cleanup
and improvement series. v1 can be found here [1]; v2 is here [2].

Changes since v2:
- Merged patches dropped
- Fixed up pickable linear ranges' selector values
- Collected tags
- Patch adding missing regulator definitions squashed into patch using
  the definitions; recommended by Krzysztof on my MT6366 series.
- Remaining dts patch split out to be sent separately

Changes since v1:
- Merged patches dropped
- Added patch to move VCN33 regulator status sync after ID check
- Added patch to fix VCN33 sync fail error message
- Added patch to add missing register definitions

Various discrepancies were found while preparing to upstream MT8186
device trees, which utilize the MT6366 PMIC, that is also covered by
this driver.

This v3 series can be seen as two parts. v1 had three parts, but one
part was fully merged, and then v2 gained another cleanup. v3 drops
the "fixing bogus regulators" part: driver changes are fully merged
and device tree change has been sent separately [3]. All patches here
should go through the regulator tree.

Part 1 - Robust chip ID checking (patch 1)

Angelo suggested making the driver fail to probe if an unexpected chip
ID was found. Patch 1 implements this.

Part 2 - Output voltage fine tuning support (patches 2, 3)

Many of the LDOs on these PMIC support an extra level of output voltage
fine tuning. Most default to no offset, but a couple have a non-zero
offset by default. Previously this was unaccounted for in the driver and
device tree constraints. On the outputs with non-zero offset, this ends
up becoming a discrepancy between the device tree and actual hardware.
These two patches adds support for this second level of tuning, modeled
as bunch of linear ranges. While it's unlikely we need this level of
control, it's nice to be able to read back the accurate hardware
settings.

The series has been reviewed, and the mfd header change has been acked
by Lee. Please merge.

Thanks
ChenYu

[1] https://lore.kernel.org/linux-arm-kernel/20230609083009.2822259-1-wenst@chromium.org/
[2] https://lore.kernel.org/linux-mediatek/20230721082903.2038975-1-wenst@chromium.org/
[3] https://lore.kernel.org/linux-mediatek/20230913084457.1638690-1-wenst@chromium.org/

Chen-Yu Tsai (3):
  regulator: mt6358: Fail probe on unknown chip ID
  regulator: mt6358: Add output voltage fine tuning to fixed regulators
  regulator: mt6358: Add output voltage fine tuning to variable LDOs

 drivers/regulator/mt6358-regulator.c | 304 ++++++++++++---------------
 include/linux/mfd/mt6358/registers.h |   6 +
 2 files changed, 144 insertions(+), 166 deletions(-)

-- 
2.42.0.515.g380fc7ccd1-goog


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH RESEND v3 1/3] regulator: mt6358: Fail probe on unknown chip ID

[Chen-Yu Tsai]

The MT6358 and MT6366 PMICs, and likely many others from MediaTek, have
a chip ID register, making the chip semi-discoverable.

The driver currently supports two PMICs and expects to be probed on one
or the other. It does not account for incorrect mfd driver entries or
device trees. While these should not happen, if they do, it could be
catastrophic for the device. The driver should be sure the hardware is
what it expects.

Make the driver fail to probe if the chip ID presented is not a known
one.

Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Fixes: f0e3c6261af1 ("regulator: mt6366: Add support for MT6366 regulator")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
---
 drivers/regulator/mt6358-regulator.c | 14 ++++++++++----
 1 file changed, 10 insertions(+), 4 deletions(-)

diff --git a/drivers/regulator/mt6358-regulator.c b/drivers/regulator/mt6358-regulator.c
index 65fbd95f1dbb..4ca8fbf4b3e2 100644
--- a/drivers/regulator/mt6358-regulator.c
+++ b/drivers/regulator/mt6358-regulator.c
@@ -688,12 +688,18 @@ static int mt6358_regulator_probe(struct platform_device *pdev)
 	const struct mt6358_regulator_info *mt6358_info;
 	int i, max_regulator, ret;
 
-	if (mt6397->chip_id == MT6366_CHIP_ID) {
-		max_regulator = MT6366_MAX_REGULATOR;
-		mt6358_info = mt6366_regulators;
-	} else {
+	switch (mt6397->chip_id) {
+	case MT6358_CHIP_ID:
 		max_regulator = MT6358_MAX_REGULATOR;
 		mt6358_info = mt6358_regulators;
+		break;
+	case MT6366_CHIP_ID:
+		max_regulator = MT6366_MAX_REGULATOR;
+		mt6358_info = mt6366_regulators;
+		break;
+	default:
+		dev_err(&pdev->dev, "unsupported chip ID: %d\n", mt6397->chip_id);
+		return -EINVAL;
 	}
 
 	ret = mt6358_sync_vcn33_setting(&pdev->dev);
-- 
2.42.0.515.g380fc7ccd1-goog


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH RESEND v3 2/3] regulator: mt6358: Add output voltage fine tuning to fixed regulators

[Chen-Yu Tsai]

The "fixed" LDO regulators found on the MT6358 and MT6366 PMICs have
either no voltage selection register, or only one valid setting.
However these do have a fine voltage calibration setting that can
slightly boost the output voltage from 0 mV to 100 mV, in 10 mV
increments.

Add support for this by changing these into linear range regulators.
Some register definitions that are missing are also added.

Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Lee Jones <lee@kernel.org>
---
 drivers/regulator/mt6358-regulator.c | 15 +++++++++++++--
 include/linux/mfd/mt6358/registers.h |  6 ++++++
 2 files changed, 19 insertions(+), 2 deletions(-)

diff --git a/drivers/regulator/mt6358-regulator.c b/drivers/regulator/mt6358-regulator.c
index 4ca8fbf4b3e2..f2eb0c14d1ed 100644
--- a/drivers/regulator/mt6358-regulator.c
+++ b/drivers/regulator/mt6358-regulator.c
@@ -123,10 +123,13 @@ struct mt6358_regulator_info {
 		.type = REGULATOR_VOLTAGE,	\
 		.id = MT6358_ID_##vreg,	\
 		.owner = THIS_MODULE,	\
-		.n_voltages = 1,	\
+		.n_voltages = 11,	\
+		.vsel_reg = MT6358_##vreg##_ANA_CON0,	\
+		.vsel_mask = GENMASK(3, 0),	\
 		.enable_reg = enreg,	\
 		.enable_mask = BIT(enbit),	\
 		.min_uV = volt,	\
+		.uV_step = 10000, \
 	},	\
 	.status_reg = MT6358_LDO_##vreg##_CON1,	\
 	.qi = BIT(15),							\
@@ -219,10 +222,13 @@ struct mt6358_regulator_info {
 		.type = REGULATOR_VOLTAGE,	\
 		.id = MT6366_ID_##vreg,	\
 		.owner = THIS_MODULE,	\
-		.n_voltages = 1,	\
+		.n_voltages = 11,	\
+		.vsel_reg = MT6358_##vreg##_ANA_CON0,	\
+		.vsel_mask = GENMASK(3, 0),	\
 		.enable_reg = enreg,	\
 		.enable_mask = BIT(enbit),	\
 		.min_uV = volt,	\
+		.uV_step = 10000, \
 	},	\
 	.status_reg = MT6358_LDO_##vreg##_CON1,	\
 	.qi = BIT(15),							\
@@ -488,8 +494,13 @@ static const struct regulator_ops mt6358_volt_table_ops = {
 	.get_status = mt6358_get_status,
 };
 
+/* "Fixed" LDOs with output voltage calibration +0 ~ +10 mV */
 static const struct regulator_ops mt6358_volt_fixed_ops = {
 	.list_voltage = regulator_list_voltage_linear,
+	.map_voltage = regulator_map_voltage_linear,
+	.set_voltage_sel = regulator_set_voltage_sel_regmap,
+	.get_voltage_sel = mt6358_get_buck_voltage_sel,
+	.set_voltage_time_sel = regulator_set_voltage_time_sel,
 	.enable = regulator_enable_regmap,
 	.disable = regulator_disable_regmap,
 	.is_enabled = regulator_is_enabled_regmap,
diff --git a/include/linux/mfd/mt6358/registers.h b/include/linux/mfd/mt6358/registers.h
index 3d33517f178c..5ea2590be710 100644
--- a/include/linux/mfd/mt6358/registers.h
+++ b/include/linux/mfd/mt6358/registers.h
@@ -262,6 +262,12 @@
 #define MT6358_LDO_VBIF28_CON3                0x1db0
 #define MT6358_VCAMA1_ANA_CON0                0x1e08
 #define MT6358_VCAMA2_ANA_CON0                0x1e0c
+#define MT6358_VFE28_ANA_CON0                 0x1e10
+#define MT6358_VCN28_ANA_CON0                 0x1e14
+#define MT6358_VBIF28_ANA_CON0                0x1e18
+#define MT6358_VAUD28_ANA_CON0                0x1e1c
+#define MT6358_VAUX18_ANA_CON0                0x1e20
+#define MT6358_VXO22_ANA_CON0                 0x1e24
 #define MT6358_VCN33_ANA_CON0                 0x1e28
 #define MT6358_VSIM1_ANA_CON0                 0x1e2c
 #define MT6358_VSIM2_ANA_CON0                 0x1e30
-- 
2.42.0.515.g380fc7ccd1-goog


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH RESEND v3 3/3] regulator: mt6358: Add output voltage fine tuning to variable LDOs

[Chen-Yu Tsai]

Some of the LDO regulators in the MT6358/MT6366 have sparsely populated
voltage tables, supported by custom get/set operators. While it works,
it requires more code and an extra field to store the lookup table.
These LDOs also have fine voltage calibration settings that can slightly
boost the output voltage from 0 mV to 100 mV, in 10 mV increments.

These combined could be modeled as a pickable set of linear ranges. The
coarse voltage setting is modeled as the range selector, while each
range has 11 selectors, starting from the range's base voltage, up to
+100 mV, in 10mV increments.

Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
---
 drivers/regulator/mt6358-regulator.c | 275 +++++++++++----------------
 1 file changed, 115 insertions(+), 160 deletions(-)

diff --git a/drivers/regulator/mt6358-regulator.c b/drivers/regulator/mt6358-regulator.c
index f2eb0c14d1ed..c4ecac5f3fc8 100644
--- a/drivers/regulator/mt6358-regulator.c
+++ b/drivers/regulator/mt6358-regulator.c
@@ -26,8 +26,6 @@ struct mt6358_regulator_info {
 	struct regulator_desc desc;
 	u32 status_reg;
 	u32 qi;
-	const u32 *index_table;
-	unsigned int n_table;
 	u32 da_vsel_reg;
 	u32 da_vsel_mask;
 	u32 modeset_reg;
@@ -64,9 +62,7 @@ struct mt6358_regulator_info {
 	.modeset_mask = BIT(_modeset_shift),	\
 }
 
-#define MT6358_LDO(match, vreg, ldo_volt_table,	\
-	ldo_index_table, enreg, enbit, vosel,	\
-	vosel_mask)	\
+#define MT6358_LDO(match, vreg, volt_ranges, enreg, enbit, vosel, vosel_mask) \
 [MT6358_ID_##vreg] = {	\
 	.desc = {	\
 		.name = #vreg,	\
@@ -75,17 +71,19 @@ struct mt6358_regulator_info {
 		.type = REGULATOR_VOLTAGE,	\
 		.id = MT6358_ID_##vreg,	\
 		.owner = THIS_MODULE,	\
-		.n_voltages = ARRAY_SIZE(ldo_volt_table),	\
-		.volt_table = ldo_volt_table,	\
-		.vsel_reg = vosel,	\
-		.vsel_mask = vosel_mask,	\
+		.n_voltages = ARRAY_SIZE(volt_ranges##_ranges) * 11,	\
+		.linear_ranges = volt_ranges##_ranges,		\
+		.linear_range_selectors_bitfield = volt_ranges##_selectors,	\
+		.n_linear_ranges = ARRAY_SIZE(volt_ranges##_ranges),	\
+		.vsel_range_reg = vosel,	\
+		.vsel_range_mask = vosel_mask,	\
+		.vsel_reg = MT6358_##vreg##_ANA_CON0,	\
+		.vsel_mask = GENMASK(3, 0),	\
 		.enable_reg = enreg,	\
 		.enable_mask = BIT(enbit),	\
 	},	\
 	.status_reg = MT6358_LDO_##vreg##_CON1,	\
 	.qi = BIT(15),	\
-	.index_table = ldo_index_table,	\
-	.n_table = ARRAY_SIZE(ldo_index_table),	\
 }
 
 #define MT6358_LDO1(match, vreg, min, max, step,	\
@@ -163,9 +161,7 @@ struct mt6358_regulator_info {
 	.modeset_mask = BIT(_modeset_shift),	\
 }
 
-#define MT6366_LDO(match, vreg, ldo_volt_table,	\
-	ldo_index_table, enreg, enbit, vosel,	\
-	vosel_mask)	\
+#define MT6366_LDO(match, vreg, volt_ranges, enreg, enbit, vosel, vosel_mask) \
 [MT6366_ID_##vreg] = {	\
 	.desc = {	\
 		.name = #vreg,	\
@@ -174,17 +170,19 @@ struct mt6358_regulator_info {
 		.type = REGULATOR_VOLTAGE,	\
 		.id = MT6366_ID_##vreg,	\
 		.owner = THIS_MODULE,	\
-		.n_voltages = ARRAY_SIZE(ldo_volt_table),	\
-		.volt_table = ldo_volt_table,	\
-		.vsel_reg = vosel,	\
-		.vsel_mask = vosel_mask,	\
+		.n_voltages = ARRAY_SIZE(volt_ranges##_ranges) * 11,	\
+		.linear_ranges = volt_ranges##_ranges,		\
+		.linear_range_selectors_bitfield = volt_ranges##_selectors,	\
+		.n_linear_ranges = ARRAY_SIZE(volt_ranges##_ranges),	\
+		.vsel_range_reg = vosel,	\
+		.vsel_range_mask = vosel_mask,	\
+		.vsel_reg = MT6358_##vreg##_ANA_CON0,	\
+		.vsel_mask = GENMASK(3, 0),	\
 		.enable_reg = enreg,	\
 		.enable_mask = BIT(enbit),	\
 	},	\
 	.status_reg = MT6358_LDO_##vreg##_CON1,	\
 	.qi = BIT(15),	\
-	.index_table = ldo_index_table,	\
-	.n_table = ARRAY_SIZE(ldo_index_table),	\
 }
 
 #define MT6366_LDO1(match, vreg, min, max, step,	\
@@ -235,95 +233,95 @@ struct mt6358_regulator_info {
 }
 
 
-static const unsigned int vdram2_voltages[] = {
-	600000, 1800000,
-};
-
-static const unsigned int vsim_voltages[] = {
-	1700000, 1800000, 2700000, 3000000, 3100000,
-};
-
-static const unsigned int vibr_voltages[] = {
-	1200000, 1300000, 1500000, 1800000,
-	2000000, 2800000, 3000000, 3300000,
+/* VDRAM2 voltage selector not shown in datasheet */
+static const unsigned int vdram2_selectors[] = { 0, 12 };
+static const struct linear_range vdram2_ranges[] = {
+	REGULATOR_LINEAR_RANGE(600000, 0, 10, 10000),
+	REGULATOR_LINEAR_RANGE(1800000, 0, 10, 10000),
 };
 
-static const unsigned int vusb_voltages[] = {
-	3000000, 3100000,
+static const unsigned int vsim_selectors[] = { 3, 4, 8, 11, 12 };
+static const struct linear_range vsim_ranges[] = {
+	REGULATOR_LINEAR_RANGE(1700000, 0, 10, 10000),
+	REGULATOR_LINEAR_RANGE(1800000, 0, 10, 10000),
+	REGULATOR_LINEAR_RANGE(2700000, 0, 10, 10000),
+	REGULATOR_LINEAR_RANGE(3000000, 0, 10, 10000),
+	REGULATOR_LINEAR_RANGE(3100000, 0, 10, 10000),
 };
 
-static const unsigned int vcamd_voltages[] = {
-	900000, 1000000, 1100000, 1200000,
-	1300000, 1500000, 1800000,
+static const unsigned int vibr_selectors[] = { 0, 1, 2, 4, 5, 9, 11, 13 };
+static const struct linear_range vibr_ranges[] = {
+	REGULATOR_LINEAR_RANGE(1200000, 0, 10, 10000),
+	REGULATOR_LINEAR_RANGE(1300000, 0, 10, 10000),
+	REGULATOR_LINEAR_RANGE(1500000, 0, 10, 10000),
+	REGULATOR_LINEAR_RANGE(1800000, 0, 10, 10000),
+	REGULATOR_LINEAR_RANGE(2000000, 0, 10, 10000),
+	REGULATOR_LINEAR_RANGE(2800000, 0, 10, 10000),
+	REGULATOR_LINEAR_RANGE(3000000, 0, 10, 10000),
+	REGULATOR_LINEAR_RANGE(3300000, 0, 10, 10000),
 };
 
-static const unsigned int vefuse_voltages[] = {
-	1700000, 1800000, 1900000,
+/* VUSB voltage selector not shown in datasheet */
+static const unsigned int vusb_selectors[] = { 3, 4 };
+static const struct linear_range vusb_ranges[] = {
+	REGULATOR_LINEAR_RANGE(3000000, 0, 10, 10000),
+	REGULATOR_LINEAR_RANGE(3100000, 0, 10, 10000),
 };
 
-static const unsigned int vmch_vemc_voltages[] = {
-	2900000, 3000000, 3300000,
+static const unsigned int vcamd_selectors[] = { 3, 4, 5, 6, 7, 9, 12 };
+static const struct linear_range vcamd_ranges[] = {
+	REGULATOR_LINEAR_RANGE(900000, 0, 10, 10000),
+	REGULATOR_LINEAR_RANGE(1000000, 0, 10, 10000),
+	REGULATOR_LINEAR_RANGE(1100000, 0, 10, 10000),
+	REGULATOR_LINEAR_RANGE(1200000, 0, 10, 10000),
+	REGULATOR_LINEAR_RANGE(1300000, 0, 10, 10000),
+	REGULATOR_LINEAR_RANGE(1500000, 0, 10, 10000),
+	REGULATOR_LINEAR_RANGE(1800000, 0, 10, 10000),
 };
 
-static const unsigned int vcama_voltages[] = {
-	1800000, 2500000, 2700000,
-	2800000, 2900000, 3000000,
+static const unsigned int vefuse_selectors[] = { 11, 12, 13 };
+static const struct linear_range vefuse_ranges[] = {
+	REGULATOR_LINEAR_RANGE(1700000, 0, 10, 10000),
+	REGULATOR_LINEAR_RANGE(1800000, 0, 10, 10000),
+	REGULATOR_LINEAR_RANGE(1900000, 0, 10, 10000),
 };
 
-static const unsigned int vcn33_voltages[] = {
-	3300000, 3400000, 3500000,
+static const unsigned int vmch_vemc_selectors[] = { 2, 3, 5 };
+static const struct linear_range vmch_vemc_ranges[] = {
+	REGULATOR_LINEAR_RANGE(2900000, 0, 10, 10000),
+	REGULATOR_LINEAR_RANGE(3000000, 0, 10, 10000),
+	REGULATOR_LINEAR_RANGE(3300000, 0, 10, 10000),
 };
 
-static const unsigned int vmc_voltages[] = {
-	1800000, 2900000, 3000000, 3300000,
+static const unsigned int vcama_selectors[] = { 0, 7, 9, 10, 11, 12 };
+static const struct linear_range vcama_ranges[] = {
+	REGULATOR_LINEAR_RANGE(1800000, 0, 10, 10000),
+	REGULATOR_LINEAR_RANGE(2500000, 0, 10, 10000),
+	REGULATOR_LINEAR_RANGE(2700000, 0, 10, 10000),
+	REGULATOR_LINEAR_RANGE(2800000, 0, 10, 10000),
+	REGULATOR_LINEAR_RANGE(2900000, 0, 10, 10000),
+	REGULATOR_LINEAR_RANGE(3000000, 0, 10, 10000),
 };
 
-static const unsigned int vldo28_voltages[] = {
-	2800000, 3000000,
+static const unsigned int vcn33_selectors[] = { 1, 2, 3 };
+static const struct linear_range vcn33_ranges[] = {
+	REGULATOR_LINEAR_RANGE(3300000, 0, 10, 10000),
+	REGULATOR_LINEAR_RANGE(3400000, 0, 10, 10000),
+	REGULATOR_LINEAR_RANGE(3500000, 0, 10, 10000),
 };
 
-static const u32 vdram2_idx[] = {
-	0, 12,
+static const unsigned int vmc_selectors[] = { 4, 10, 11, 13 };
+static const struct linear_range vmc_ranges[] = {
+	REGULATOR_LINEAR_RANGE(1800000, 0, 10, 10000),
+	REGULATOR_LINEAR_RANGE(2900000, 0, 10, 10000),
+	REGULATOR_LINEAR_RANGE(3000000, 0, 10, 10000),
+	REGULATOR_LINEAR_RANGE(3300000, 0, 10, 10000),
 };
 
-static const u32 vsim_idx[] = {
-	3, 4, 8, 11, 12,
-};
-
-static const u32 vibr_idx[] = {
-	0, 1, 2, 4, 5, 9, 11, 13,
-};
-
-static const u32 vusb_idx[] = {
-	3, 4,
-};
-
-static const u32 vcamd_idx[] = {
-	3, 4, 5, 6, 7, 9, 12,
-};
-
-static const u32 vefuse_idx[] = {
-	11, 12, 13,
-};
-
-static const u32 vmch_vemc_idx[] = {
-	2, 3, 5,
-};
-
-static const u32 vcama_idx[] = {
-	0, 7, 9, 10, 11, 12,
-};
-
-static const u32 vcn33_idx[] = {
-	1, 2, 3,
-};
-
-static const u32 vmc_idx[] = {
-	4, 10, 11, 13,
-};
-
-static const u32 vldo28_idx[] = {
-	1, 3,
+static const unsigned int vldo28_selectors[] = { 1, 3 };
+static const struct linear_range vldo28_ranges[] = {
+	REGULATOR_LINEAR_RANGE(2800000, 0, 10, 10000),
+	REGULATOR_LINEAR_RANGE(3000000, 0, 10, 10000),
 };
 
 static unsigned int mt6358_map_mode(unsigned int mode)
@@ -332,49 +330,6 @@ static unsigned int mt6358_map_mode(unsigned int mode)
 		REGULATOR_MODE_NORMAL : REGULATOR_MODE_FAST;
 }
 
-static int mt6358_set_voltage_sel(struct regulator_dev *rdev,
-				  unsigned int selector)
-{
-	const struct mt6358_regulator_info *info = to_regulator_info(rdev->desc);
-	int idx, ret;
-	const u32 *pvol;
-
-	pvol = info->index_table;
-
-	idx = pvol[selector];
-	idx <<= ffs(info->desc.vsel_mask) - 1;
-	ret = regmap_update_bits(rdev->regmap, info->desc.vsel_reg,
-				 info->desc.vsel_mask, idx);
-
-	return ret;
-}
-
-static int mt6358_get_voltage_sel(struct regulator_dev *rdev)
-{
-	const struct mt6358_regulator_info *info = to_regulator_info(rdev->desc);
-	int idx, ret;
-	u32 selector;
-	const u32 *pvol;
-
-	ret = regmap_read(rdev->regmap, info->desc.vsel_reg, &selector);
-	if (ret != 0) {
-		dev_info(&rdev->dev,
-			 "Failed to get mt6358 %s vsel reg: %d\n",
-			 info->desc.name, ret);
-		return ret;
-	}
-
-	selector = (selector & info->desc.vsel_mask) >>
-			(ffs(info->desc.vsel_mask) - 1);
-	pvol = info->index_table;
-	for (idx = 0; idx < info->desc.n_voltages; idx++) {
-		if (pvol[idx] == selector)
-			return idx;
-	}
-
-	return -EINVAL;
-}
-
 static int mt6358_get_buck_voltage_sel(struct regulator_dev *rdev)
 {
 	const struct mt6358_regulator_info *info = to_regulator_info(rdev->desc);
@@ -483,10 +438,10 @@ static const struct regulator_ops mt6358_volt_range_ops = {
 };
 
 static const struct regulator_ops mt6358_volt_table_ops = {
-	.list_voltage = regulator_list_voltage_table,
-	.map_voltage = regulator_map_voltage_iterate,
-	.set_voltage_sel = mt6358_set_voltage_sel,
-	.get_voltage_sel = mt6358_get_voltage_sel,
+	.list_voltage = regulator_list_voltage_pickable_linear_range,
+	.map_voltage = regulator_map_voltage_pickable_linear_range,
+	.set_voltage_sel = regulator_set_voltage_sel_pickable_regmap,
+	.get_voltage_sel = regulator_get_voltage_sel_pickable_regmap,
 	.set_voltage_time_sel = regulator_set_voltage_time_sel,
 	.enable = regulator_enable_regmap,
 	.disable = regulator_disable_regmap,
@@ -546,34 +501,34 @@ static const struct mt6358_regulator_info mt6358_regulators[] = {
 	MT6358_REG_FIXED("ldo_vrf18", VRF18, MT6358_LDO_VRF18_CON0, 0, 1800000),
 	MT6358_REG_FIXED("ldo_vaud28", VAUD28,
 			 MT6358_LDO_VAUD28_CON0, 0, 2800000),
-	MT6358_LDO("ldo_vdram2", VDRAM2, vdram2_voltages, vdram2_idx,
+	MT6358_LDO("ldo_vdram2", VDRAM2, vdram2,
 		   MT6358_LDO_VDRAM2_CON0, 0, MT6358_LDO_VDRAM2_ELR0, 0xf),
-	MT6358_LDO("ldo_vsim1", VSIM1, vsim_voltages, vsim_idx,
+	MT6358_LDO("ldo_vsim1", VSIM1, vsim,
 		   MT6358_LDO_VSIM1_CON0, 0, MT6358_VSIM1_ANA_CON0, 0xf00),
-	MT6358_LDO("ldo_vibr", VIBR, vibr_voltages, vibr_idx,
+	MT6358_LDO("ldo_vibr", VIBR, vibr,
 		   MT6358_LDO_VIBR_CON0, 0, MT6358_VIBR_ANA_CON0, 0xf00),
-	MT6358_LDO("ldo_vusb", VUSB, vusb_voltages, vusb_idx,
+	MT6358_LDO("ldo_vusb", VUSB, vusb,
 		   MT6358_LDO_VUSB_CON0_0, 0, MT6358_VUSB_ANA_CON0, 0x700),
-	MT6358_LDO("ldo_vcamd", VCAMD, vcamd_voltages, vcamd_idx,
+	MT6358_LDO("ldo_vcamd", VCAMD, vcamd,
 		   MT6358_LDO_VCAMD_CON0, 0, MT6358_VCAMD_ANA_CON0, 0xf00),
-	MT6358_LDO("ldo_vefuse", VEFUSE, vefuse_voltages, vefuse_idx,
+	MT6358_LDO("ldo_vefuse", VEFUSE, vefuse,
 		   MT6358_LDO_VEFUSE_CON0, 0, MT6358_VEFUSE_ANA_CON0, 0xf00),
-	MT6358_LDO("ldo_vmch", VMCH, vmch_vemc_voltages, vmch_vemc_idx,
+	MT6358_LDO("ldo_vmch", VMCH, vmch_vemc,
 		   MT6358_LDO_VMCH_CON0, 0, MT6358_VMCH_ANA_CON0, 0x700),
-	MT6358_LDO("ldo_vcama1", VCAMA1, vcama_voltages, vcama_idx,
+	MT6358_LDO("ldo_vcama1", VCAMA1, vcama,
 		   MT6358_LDO_VCAMA1_CON0, 0, MT6358_VCAMA1_ANA_CON0, 0xf00),
-	MT6358_LDO("ldo_vemc", VEMC, vmch_vemc_voltages, vmch_vemc_idx,
+	MT6358_LDO("ldo_vemc", VEMC, vmch_vemc,
 		   MT6358_LDO_VEMC_CON0, 0, MT6358_VEMC_ANA_CON0, 0x700),
-	MT6358_LDO("ldo_vcn33", VCN33, vcn33_voltages, vcn33_idx,
+	MT6358_LDO("ldo_vcn33", VCN33, vcn33,
 		   MT6358_LDO_VCN33_CON0_0, 0, MT6358_VCN33_ANA_CON0, 0x300),
-	MT6358_LDO("ldo_vcama2", VCAMA2, vcama_voltages, vcama_idx,
+	MT6358_LDO("ldo_vcama2", VCAMA2, vcama,
 		   MT6358_LDO_VCAMA2_CON0, 0, MT6358_VCAMA2_ANA_CON0, 0xf00),
-	MT6358_LDO("ldo_vmc", VMC, vmc_voltages, vmc_idx,
+	MT6358_LDO("ldo_vmc", VMC, vmc,
 		   MT6358_LDO_VMC_CON0, 0, MT6358_VMC_ANA_CON0, 0xf00),
-	MT6358_LDO("ldo_vldo28", VLDO28, vldo28_voltages, vldo28_idx,
+	MT6358_LDO("ldo_vldo28", VLDO28, vldo28,
 		   MT6358_LDO_VLDO28_CON0_0, 0,
 		   MT6358_VLDO28_ANA_CON0, 0x300),
-	MT6358_LDO("ldo_vsim2", VSIM2, vsim_voltages, vsim_idx,
+	MT6358_LDO("ldo_vsim2", VSIM2, vsim,
 		   MT6358_LDO_VSIM2_CON0, 0, MT6358_VSIM2_ANA_CON0, 0xf00),
 	MT6358_LDO1("ldo_vsram_proc11", VSRAM_PROC11, 500000, 1293750, 6250,
 		    MT6358_LDO_VSRAM_PROC11_DBG0, 0x7f00, MT6358_LDO_VSRAM_CON0, 0x7f),
@@ -622,25 +577,25 @@ static const struct mt6358_regulator_info mt6366_regulators[] = {
 	MT6366_REG_FIXED("ldo_vrf18", VRF18, MT6358_LDO_VRF18_CON0, 0, 1800000),
 	MT6366_REG_FIXED("ldo_vaud28", VAUD28,
 			 MT6358_LDO_VAUD28_CON0, 0, 2800000),
-	MT6366_LDO("ldo_vdram2", VDRAM2, vdram2_voltages, vdram2_idx,
+	MT6366_LDO("ldo_vdram2", VDRAM2, vdram2,
 		   MT6358_LDO_VDRAM2_CON0, 0, MT6358_LDO_VDRAM2_ELR0, 0x10),
-	MT6366_LDO("ldo_vsim1", VSIM1, vsim_voltages, vsim_idx,
+	MT6366_LDO("ldo_vsim1", VSIM1, vsim,
 		   MT6358_LDO_VSIM1_CON0, 0, MT6358_VSIM1_ANA_CON0, 0xf00),
-	MT6366_LDO("ldo_vibr", VIBR, vibr_voltages, vibr_idx,
+	MT6366_LDO("ldo_vibr", VIBR, vibr,
 		   MT6358_LDO_VIBR_CON0, 0, MT6358_VIBR_ANA_CON0, 0xf00),
-	MT6366_LDO("ldo_vusb", VUSB, vusb_voltages, vusb_idx,
+	MT6366_LDO("ldo_vusb", VUSB, vusb,
 		   MT6358_LDO_VUSB_CON0_0, 0, MT6358_VUSB_ANA_CON0, 0x700),
-	MT6366_LDO("ldo_vefuse", VEFUSE, vefuse_voltages, vefuse_idx,
+	MT6366_LDO("ldo_vefuse", VEFUSE, vefuse,
 		   MT6358_LDO_VEFUSE_CON0, 0, MT6358_VEFUSE_ANA_CON0, 0xf00),
-	MT6366_LDO("ldo_vmch", VMCH, vmch_vemc_voltages, vmch_vemc_idx,
+	MT6366_LDO("ldo_vmch", VMCH, vmch_vemc,
 		   MT6358_LDO_VMCH_CON0, 0, MT6358_VMCH_ANA_CON0, 0x700),
-	MT6366_LDO("ldo_vemc", VEMC, vmch_vemc_voltages, vmch_vemc_idx,
+	MT6366_LDO("ldo_vemc", VEMC, vmch_vemc,
 		   MT6358_LDO_VEMC_CON0, 0, MT6358_VEMC_ANA_CON0, 0x700),
-	MT6366_LDO("ldo_vcn33", VCN33, vcn33_voltages, vcn33_idx,
+	MT6366_LDO("ldo_vcn33", VCN33, vcn33,
 		   MT6358_LDO_VCN33_CON0_0, 0, MT6358_VCN33_ANA_CON0, 0x300),
-	MT6366_LDO("ldo_vmc", VMC, vmc_voltages, vmc_idx,
+	MT6366_LDO("ldo_vmc", VMC, vmc,
 		   MT6358_LDO_VMC_CON0, 0, MT6358_VMC_ANA_CON0, 0xf00),
-	MT6366_LDO("ldo_vsim2", VSIM2, vsim_voltages, vsim_idx,
+	MT6366_LDO("ldo_vsim2", VSIM2, vsim,
 		   MT6358_LDO_VSIM2_CON0, 0, MT6358_VSIM2_ANA_CON0, 0xf00),
 	MT6366_LDO1("ldo_vsram_proc11", VSRAM_PROC11, 500000, 1293750, 6250,
 		    MT6358_LDO_VSRAM_PROC11_DBG0, 0x7f00, MT6358_LDO_VSRAM_CON0, 0x7f),
-- 
2.42.0.515.g380fc7ccd1-goog


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH RESEND v3 0/3] regulator: mt6358: Remove bogus regulators and improvements

[Mark Brown]

[-- Attachment #1.1: Type: text/plain, Size: 264 bytes --]

On Tue, Sep 26, 2023 at 12:34:45PM +0800, Chen-Yu Tsai wrote:
> Hi,
> 
> This seems to have fallen through the cracks, so I'm resending with tags
> collected and patches rebased onto next-20230925. The diffs remain the
> same.

AFAICT this is still in CI.

[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]

[-- Attachment #2: Type: text/plain, Size: 176 bytes --]

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel