* [PATCH v6 2/2] arm64: dts: amlogic: Used onboard usb hub reset on odroid n2
[not found] <20231204144429.45197-1-linux.amoon@gmail.com>
@ 2023-12-04 14:44 ` Anand Moon
0 siblings, 0 replies; only message in thread
From: Anand Moon @ 2023-12-04 14:44 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Neil Armstrong,
Kevin Hilman, Jerome Brunet, Martin Blumenstingl
Cc: Anand Moon, linux-amlogic, devicetree, linux-arm-kernel,
linux-kernel
On Odroid n2/n2+ previously use gpio-hog to reset the usb hub,
switch to used on-board usb hub reset to enable the usb hub
and enable power to hub.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
---
V6:none
V5:none
V4:none
V3:none
V2:none
V1:none
---
.../dts/amlogic/meson-g12b-odroid-n2.dtsi | 36 ++++++++++++-------
1 file changed, 24 insertions(+), 12 deletions(-)
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi
index 91c9769fda20..9e671444eca6 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi
@@ -31,6 +31,30 @@ hub_5v: regulator-hub_5v {
enable-active-high;
};
+ /* USB hub supports both USB 2.0 and USB 3.0 root hub */
+ usb-hub {
+ dr_mode = "host";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* 2.0 hub on port 1 */
+ hub_2_0: hub@1 {
+ compatible = "usb5e3,610";
+ reg = <1>;
+ peer-hub = <&hub_3_0>;
+ vdd-supply = <&usb_pwr_en>;
+ };
+
+ /* 3.0 hub on port 4 */
+ hub_3_0: hub@2 {
+ compatible = "usb5e3,620";
+ reg = <2>;
+ peer-hub = <&hub_2_0>;
+ reset-gpios = <&gpio GPIOH_4 GPIO_ACTIVE_LOW>;
+ vdd-supply = <&vcc_5v>;
+ };
+ };
+
sound {
compatible = "amlogic,axg-sound-card";
model = "ODROID-N2";
@@ -234,18 +258,6 @@ &gpio {
"PIN_3", /* GPIOX_17 */
"PIN_5", /* GPIOX_18 */
"PIN_36"; /* GPIOX_19 */
- /*
- * WARNING: The USB Hub on the Odroid-N2 needs a reset signal
- * to be turned high in order to be detected by the USB Controller
- * This signal should be handled by a USB specific power sequence
- * in order to reset the Hub when USB bus is powered down.
- */
- usb-hub-hog {
- gpio-hog;
- gpios = <GPIOH_4 GPIO_ACTIVE_HIGH>;
- output-high;
- line-name = "usb-hub-reset";
- };
};
&i2c3 {
--
2.42.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] only message in thread
only message in thread, other threads:[~2023-12-04 14:45 UTC | newest]
Thread overview: (only message) (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <20231204144429.45197-1-linux.amoon@gmail.com>
2023-12-04 14:44 ` [PATCH v6 2/2] arm64: dts: amlogic: Used onboard usb hub reset on odroid n2 Anand Moon
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).