[PATCH v2] ARM: dts: imx: Use flash@0,0 pattern

[PATCH v2] ARM: dts: imx: Use flash@0,0 pattern

[Fabio Estevam]

From: Fabio Estevam <festevam@denx.de>

Per mtd-physmap.yaml, 'nor@0,0' is not a valid node pattern.

Change it to 'flash@0,0' to fix the following dt-schema warning:

imx1-ads.dtb: nor@0,0: $nodename:0: 'nor@0,0' does not match '^(flash|.*sram|nand)(@.*)?$'
	from schema $id: http://devicetree.org/schemas/mtd/mtd-physmap.yaml#

Signed-off-by: Fabio Estevam <festevam@denx.de>
---
Changes since v1:
- Fix Subject.

 arch/arm/boot/dts/nxp/imx/imx1-ads.dts                  | 2 +-
 arch/arm/boot/dts/nxp/imx/imx1-apf9328.dts              | 2 +-
 arch/arm/boot/dts/nxp/imx/imx27-eukrea-cpuimx27.dtsi    | 2 +-
 arch/arm/boot/dts/nxp/imx/imx27-phytec-phycore-som.dtsi | 2 +-
 4 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx1-ads.dts b/arch/arm/boot/dts/nxp/imx/imx1-ads.dts
index 5833fb6f15d8..2c817c4a4c68 100644
--- a/arch/arm/boot/dts/nxp/imx/imx1-ads.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx1-ads.dts
@@ -65,7 +65,7 @@ &weim {
 	pinctrl-0 = <&pinctrl_weim>;
 	status = "okay";
 
-	nor: nor@0,0 {
+	nor: flash@0,0 {
 		compatible = "cfi-flash";
 		reg = <0 0x00000000 0x02000000>;
 		bank-width = <4>;
diff --git a/arch/arm/boot/dts/nxp/imx/imx1-apf9328.dts b/arch/arm/boot/dts/nxp/imx/imx1-apf9328.dts
index 1f11e9542a72..e66eef87a7a4 100644
--- a/arch/arm/boot/dts/nxp/imx/imx1-apf9328.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx1-apf9328.dts
@@ -45,7 +45,7 @@ &weim {
 	pinctrl-0 = <&pinctrl_weim>;
 	status = "okay";
 
-	nor: nor@0,0 {
+	nor: flash@0,0 {
 		compatible = "cfi-flash";
 		reg = <0 0x00000000 0x02000000>;
 		bank-width = <2>;
diff --git a/arch/arm/boot/dts/nxp/imx/imx27-eukrea-cpuimx27.dtsi b/arch/arm/boot/dts/nxp/imx/imx27-eukrea-cpuimx27.dtsi
index 4b83e2918b55..c7e923584878 100644
--- a/arch/arm/boot/dts/nxp/imx/imx27-eukrea-cpuimx27.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx27-eukrea-cpuimx27.dtsi
@@ -90,7 +90,7 @@ &usbotg {
 &weim {
 	status = "okay";
 
-	nor: nor@0,0 {
+	nor: flash@0,0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "cfi-flash";
diff --git a/arch/arm/boot/dts/nxp/imx/imx27-phytec-phycore-som.dtsi b/arch/arm/boot/dts/nxp/imx/imx27-phytec-phycore-som.dtsi
index 7b2ea4cdae58..8d428c844666 100644
--- a/arch/arm/boot/dts/nxp/imx/imx27-phytec-phycore-som.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx27-phytec-phycore-som.dtsi
@@ -314,7 +314,7 @@ &usbotg {
 &weim {
 	status = "okay";
 
-	nor: nor@0,0 {
+	nor: flash@0,0 {
 		compatible = "cfi-flash";
 		reg = <0 0x00000000 0x02000000>;
 		bank-width = <2>;
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v2] ARM: dts: imx: Use flash@0,0 pattern

[Shawn Guo]

On Wed, Dec 06, 2023 at 09:36:05AM -0300, Fabio Estevam wrote:
> From: Fabio Estevam <festevam@denx.de>
> 
> Per mtd-physmap.yaml, 'nor@0,0' is not a valid node pattern.
> 
> Change it to 'flash@0,0' to fix the following dt-schema warning:
> 
> imx1-ads.dtb: nor@0,0: $nodename:0: 'nor@0,0' does not match '^(flash|.*sram|nand)(@.*)?$'
> 	from schema $id: http://devicetree.org/schemas/mtd/mtd-physmap.yaml#
> 
> Signed-off-by: Fabio Estevam <festevam@denx.de>

Applied, thanks!

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel