[PATCH v7 0/5] TI K3 M4F support on AM64x and AM62x SoCs

[PATCH v7 0/5] TI K3 M4F support on AM64x and AM62x SoCs

[Hari Nagalla]

The following series introduces K3 M4F remoteproc driver support for
AM64x and AM62x SoC families. These SoCs have a ARM Cortex M4F core in
the MCU voltage domain. For safety oriented applications, this core is
operated independently with out any IPC to other cores on the SoC.
However, for non safety applications, some customers use it as a remote
processor and so linux remote proc support is extended to the M4F core.

See AM64x Technical Reference Manual (SPRUIM2C – SEPTEMBER 2021) for
further details: https://www.ti.com/lit/pdf/SPRUIM2

See AM62x Technical Reference Manual (SPRUIV7A – MAY 2022) for
further details: https://www.ti.com/lit/pdf/SPRUIV7A

kernel build log: https://paste.sr.ht/~hnagalla/be9d1c45e176ea8fa274ab13a3da43a9853fcf7f
dt-binding-check log: https://paste.sr.ht/~hnagalla/25912c85f6a8c68e3da24053fc060f38024fb8ab 
kernel boot log: https://paste.sr.ht/~hnagalla/5ba77847343f22b5f9ec2b7aeabc410aaf8cdf45

Hari Nagalla (2):
  dt-bindings: remoteproc: k3-m4f: Add K3 AM64x SoCs
  arm64: defconfig: Enable TI K3 M4 remote proc driver

Martyn Welch (3):
  remoteproc: k3: Move out data structures common with M4 driver
  remoteproc: k3: Move out functions common with M4 driver
  remoteproc: k3-m4: Add a remoteproc driver for M4F subsystem

 .../bindings/remoteproc/ti,k3-m4f-rproc.yaml  |  138 ++
 arch/arm64/configs/defconfig                  |    1 +
 drivers/remoteproc/Kconfig                    |   13 +
 drivers/remoteproc/Makefile                   |    3 +-
 drivers/remoteproc/ti_k3_common.c             |  583 ++++++++
 drivers/remoteproc/ti_k3_common.h             |  107 ++
 drivers/remoteproc/ti_k3_dsp_remoteproc.c     | 1277 +++++------------
 drivers/remoteproc/ti_k3_m4_remoteproc.c      |  327 +++++
 8 files changed, 1539 insertions(+), 910 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/remoteproc/ti,k3-m4f-rproc.yaml
 create mode 100644 drivers/remoteproc/ti_k3_common.c
 create mode 100644 drivers/remoteproc/ti_k3_common.h
 rewrite drivers/remoteproc/ti_k3_dsp_remoteproc.c (67%)
 create mode 100644 drivers/remoteproc/ti_k3_m4_remoteproc.c

-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v7 1/5] dt-bindings: remoteproc: k3-m4f: Add K3 AM64x SoCs

[Hari Nagalla]

K3 AM64x SoC has a Cortex M4F subsystem in the MCU voltage domain.
The remote processor's life cycle management and IPC mechanisms are
similar across the R5F and M4F cores from remote processor driver
point of view. However, there are subtle differences in image loading
and starting the M4F subsystems.

The YAML binding document provides the various node properties to be
configured by the consumers of the M4F subsystem.

Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
---
Changes since v1:
 - Spelling corrections
 - Corrected to pass DT checks

Changes since v2:
 - Missed spelling correction to commit message

Changes since v3:
 - Removed unnecessary descriptions and used generic memory region names
 - Made mboxes and memory-region optional
 - Removed unrelated items from examples

Changes since v4:
 - Rebased to the latest kernel-next tree
 - Added optional sram memory region for m4f device node

Changes since v5:
 - None

Changes since v6:
 - Removed blank line, fixed type for firm-ware property and binding check
   errors.

link to v6:
  https://lore.kernel.org/all/20230913111644.29889-2-hnagalla@ti.com/

 .../bindings/remoteproc/ti,k3-m4f-rproc.yaml  | 138 ++++++++++++++++++
 1 file changed, 138 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/remoteproc/ti,k3-m4f-rproc.yaml

diff --git a/Documentation/devicetree/bindings/remoteproc/ti,k3-m4f-rproc.yaml b/Documentation/devicetree/bindings/remoteproc/ti,k3-m4f-rproc.yaml
new file mode 100644
index 000000000000..645dbce3773b
--- /dev/null
+++ b/Documentation/devicetree/bindings/remoteproc/ti,k3-m4f-rproc.yaml
@@ -0,0 +1,138 @@
+# SPDX-License-Identifier: (GPL-2.0-only or BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/remoteproc/ti,k3-m4f-rproc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: TI K3 M4F processor subsystems
+
+maintainers:
+  - Hari Nagalla <hnagalla@ti.com>
+  - Mathieu Poirier <mathieu.poirier@linaro.org>
+
+description: |
+  Some K3 family SoCs have Arm Cortex M4F cores. AM64x is a SoC in K3
+  family with a M4F core. Typically safety oriented applications may use
+  the M4F core in isolation without an IPC. Where as some industrial and
+  home automation applications, may use the M4F core as a remote processor
+  with IPC communications.
+
+$ref: /schemas/arm/keystone/ti,k3-sci-common.yaml#
+
+properties:
+  compatible:
+    enum:
+      - ti,am64-m4fss
+
+  power-domains:
+    maxItems: 1
+
+  "#address-cells":
+    const: 2
+
+  "#size-cells":
+    const: 2
+
+  reg:
+    items:
+      - description: IRAM internal memory region
+      - description: DRAM internal memory region
+
+  reg-names:
+    items:
+      - const: iram
+      - const: dram
+
+  resets:
+    maxItems: 1
+
+  firmware-name:
+    maxItems: 1
+    description: Name of firmware to load for the M4F core
+
+  mboxes:
+    description: |
+      OMAP Mailbox specifier denoting the sub-mailbox, to be used for
+      communication with the remote processor. This property should match
+      with the sub-mailbox node used in the firmware image.
+    maxItems: 1
+
+  memory-region:
+    description: |
+      phandle to the reserved memory nodes to be associated with the
+      remoteproc device. The reserved memory nodes should be carveout nodes,
+      and should be defined with a "no-map" property as per the bindings in
+      Documentation/devicetree/bindings/reserved-memory/reserved-memory.yaml
+      Optional memory regions available for firmware specific purposes.
+    maxItems: 8
+    items:
+      - description: regions used for DMA allocations like vrings, vring buffers
+                     and memory dedicated to firmware's specific purposes.
+    additionalItems: true
+
+  sram:
+    $ref: /schemas/types.yaml#/definitions/phandle-array
+    maxItems: 4
+    items:
+      maxItems: 1
+    description: |
+      phandles to reserved on-chip SRAM regions. The regions should be
+      defined as child nodes of the respective SRAM node, and
+      should be defined as per the generic bindings in,
+      Documentation/devicetree/bindings/sram/sram.yaml
+
+required:
+  - compatible
+  - reg
+  - reg-names
+  - ti,sci
+  - ti,sci-dev-id
+  - ti,sci-proc-ids
+  - resets
+  - firmware-name
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    reserved-memory {
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        mcu_m4fss_dma_memory_region: m4f-dma-memory@9cb00000 {
+            compatible = "shared-dma-pool";
+            reg = <0x00 0x9cb00000 0x00 0x100000>;
+            no-map;
+        };
+
+        mcu_m4fss_memory_region: m4f-memory@9cc00000 {
+            compatible = "shared-dma-pool";
+            reg = <0x00 0x9cc00000 0x00 0xe00000>;
+            no-map;
+        };
+    };
+
+    soc {
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        mailbox0_cluster0: mailbox-0 {
+            #mbox-cells = <1>;
+        };
+
+        remoteproc@5000000 {
+            compatible = "ti,am64-m4fss";
+            reg = <0x00 0x5000000 0x00 0x30000>,
+                  <0x00 0x5040000 0x00 0x10000>;
+            reg-names = "iram", "dram";
+            ti,sci = <&dmsc>;
+            ti,sci-dev-id = <9>;
+            ti,sci-proc-ids = <0x18 0xff>;
+            resets = <&k3_reset 9 1>;
+            firmware-name = "am62-mcu-m4f0_0-fw";
+            mboxes = <&mailbox0_cluster0>, <&mbox_m4_0>;
+            memory-region = <&mcu_m4fss_dma_memory_region>,
+                            <&mcu_m4fss_memory_region>;
+            sram = <&oc_sram>;
+         };
+    };
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v7 1/5] dt-bindings: remoteproc: k3-m4f: Add K3 AM64x SoCs

[Rob Herring]

On Fri, 02 Feb 2024 11:55:34 -0600, Hari Nagalla wrote:
> K3 AM64x SoC has a Cortex M4F subsystem in the MCU voltage domain.
> The remote processor's life cycle management and IPC mechanisms are
> similar across the R5F and M4F cores from remote processor driver
> point of view. However, there are subtle differences in image loading
> and starting the M4F subsystems.
> 
> The YAML binding document provides the various node properties to be
> configured by the consumers of the M4F subsystem.
> 
> Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
> Signed-off-by: Hari Nagalla <hnagalla@ti.com>
> ---
> Changes since v1:
>  - Spelling corrections
>  - Corrected to pass DT checks
> 
> Changes since v2:
>  - Missed spelling correction to commit message
> 
> Changes since v3:
>  - Removed unnecessary descriptions and used generic memory region names
>  - Made mboxes and memory-region optional
>  - Removed unrelated items from examples
> 
> Changes since v4:
>  - Rebased to the latest kernel-next tree
>  - Added optional sram memory region for m4f device node
> 
> Changes since v5:
>  - None
> 
> Changes since v6:
>  - Removed blank line, fixed type for firm-ware property and binding check
>    errors.
> 
> link to v6:
>   https://lore.kernel.org/all/20230913111644.29889-2-hnagalla@ti.com/
> 
>  .../bindings/remoteproc/ti,k3-m4f-rproc.yaml  | 138 ++++++++++++++++++
>  1 file changed, 138 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/remoteproc/ti,k3-m4f-rproc.yaml
> 

My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
on your patch (DT_CHECKER_FLAGS is new in v5.13):

yamllint warnings/errors:

dtschema/dtc warnings/errors:


doc reference errors (make refcheckdocs):
Warning: Documentation/devicetree/bindings/remoteproc/ti,k3-m4f-rproc.yaml references a file that doesn't exist: Documentation/devicetree/bindings/reserved-memory/reserved-memory.yaml
Documentation/devicetree/bindings/remoteproc/ti,k3-m4f-rproc.yaml: Documentation/devicetree/bindings/reserved-memory/reserved-memory.yaml

See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20240202175538.1705-2-hnagalla@ti.com

The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v7 1/5] dt-bindings: remoteproc: k3-m4f: Add K3 AM64x SoCs

[Rob Herring]

On Fri, Feb 02, 2024 at 11:55:34AM -0600, Hari Nagalla wrote:
> K3 AM64x SoC has a Cortex M4F subsystem in the MCU voltage domain.
> The remote processor's life cycle management and IPC mechanisms are
> similar across the R5F and M4F cores from remote processor driver
> point of view. However, there are subtle differences in image loading
> and starting the M4F subsystems.
> 
> The YAML binding document provides the various node properties to be
> configured by the consumers of the M4F subsystem.
> 
> Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
> Signed-off-by: Hari Nagalla <hnagalla@ti.com>
> ---
> Changes since v1:
>  - Spelling corrections
>  - Corrected to pass DT checks
> 
> Changes since v2:
>  - Missed spelling correction to commit message
> 
> Changes since v3:
>  - Removed unnecessary descriptions and used generic memory region names
>  - Made mboxes and memory-region optional
>  - Removed unrelated items from examples
> 
> Changes since v4:
>  - Rebased to the latest kernel-next tree
>  - Added optional sram memory region for m4f device node
> 
> Changes since v5:
>  - None
> 
> Changes since v6:
>  - Removed blank line, fixed type for firm-ware property and binding check
>    errors.
> 
> link to v6:
>   https://lore.kernel.org/all/20230913111644.29889-2-hnagalla@ti.com/
> 
>  .../bindings/remoteproc/ti,k3-m4f-rproc.yaml  | 138 ++++++++++++++++++
>  1 file changed, 138 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/remoteproc/ti,k3-m4f-rproc.yaml
> 
> diff --git a/Documentation/devicetree/bindings/remoteproc/ti,k3-m4f-rproc.yaml b/Documentation/devicetree/bindings/remoteproc/ti,k3-m4f-rproc.yaml
> new file mode 100644
> index 000000000000..645dbce3773b
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/remoteproc/ti,k3-m4f-rproc.yaml
> @@ -0,0 +1,138 @@
> +# SPDX-License-Identifier: (GPL-2.0-only or BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/remoteproc/ti,k3-m4f-rproc.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: TI K3 M4F processor subsystems
> +
> +maintainers:
> +  - Hari Nagalla <hnagalla@ti.com>
> +  - Mathieu Poirier <mathieu.poirier@linaro.org>
> +
> +description: |
> +  Some K3 family SoCs have Arm Cortex M4F cores. AM64x is a SoC in K3
> +  family with a M4F core. Typically safety oriented applications may use
> +  the M4F core in isolation without an IPC. Where as some industrial and
> +  home automation applications, may use the M4F core as a remote processor
> +  with IPC communications.
> +
> +$ref: /schemas/arm/keystone/ti,k3-sci-common.yaml#
> +
> +properties:
> +  compatible:
> +    enum:
> +      - ti,am64-m4fss
> +
> +  power-domains:
> +    maxItems: 1
> +
> +  "#address-cells":
> +    const: 2
> +
> +  "#size-cells":
> +    const: 2
> +
> +  reg:
> +    items:
> +      - description: IRAM internal memory region
> +      - description: DRAM internal memory region
> +
> +  reg-names:
> +    items:
> +      - const: iram
> +      - const: dram
> +
> +  resets:
> +    maxItems: 1
> +
> +  firmware-name:
> +    maxItems: 1
> +    description: Name of firmware to load for the M4F core
> +
> +  mboxes:
> +    description: |

Don't need '|' if no formatting.

> +      OMAP Mailbox specifier denoting the sub-mailbox, to be used for
> +      communication with the remote processor. This property should match
> +      with the sub-mailbox node used in the firmware image.
> +    maxItems: 1
> +
> +  memory-region:
> +    description: |
> +      phandle to the reserved memory nodes to be associated with the
> +      remoteproc device. The reserved memory nodes should be carveout nodes,
> +      and should be defined with a "no-map" property as per the bindings in
> +      Documentation/devicetree/bindings/reserved-memory/reserved-memory.yaml

This has moved to dtschema. I'd just drop the file name.

> +      Optional memory regions available for firmware specific purposes.
> +    maxItems: 8
> +    items:
> +      - description: regions used for DMA allocations like vrings, vring buffers
> +                     and memory dedicated to firmware's specific purposes.
> +    additionalItems: true

I think you want just:

minItems: 1
maxItems: 8

> +
> +  sram:
> +    $ref: /schemas/types.yaml#/definitions/phandle-array
> +    maxItems: 4
> +    items:
> +      maxItems: 1
> +    description: |
> +      phandles to reserved on-chip SRAM regions. The regions should be
> +      defined as child nodes of the respective SRAM node, and
> +      should be defined as per the generic bindings in,
> +      Documentation/devicetree/bindings/sram/sram.yaml
> +
> +required:
> +  - compatible
> +  - reg
> +  - reg-names
> +  - ti,sci
> +  - ti,sci-dev-id
> +  - ti,sci-proc-ids
> +  - resets
> +  - firmware-name
> +
> +unevaluatedProperties: false
> +
> +examples:
> +  - |
> +    reserved-memory {
> +        #address-cells = <2>;
> +        #size-cells = <2>;
> +
> +        mcu_m4fss_dma_memory_region: m4f-dma-memory@9cb00000 {
> +            compatible = "shared-dma-pool";
> +            reg = <0x00 0x9cb00000 0x00 0x100000>;
> +            no-map;
> +        };
> +
> +        mcu_m4fss_memory_region: m4f-memory@9cc00000 {
> +            compatible = "shared-dma-pool";
> +            reg = <0x00 0x9cc00000 0x00 0xe00000>;
> +            no-map;
> +        };
> +    };
> +
> +    soc {
> +        #address-cells = <2>;
> +        #size-cells = <2>;
> +
> +        mailbox0_cluster0: mailbox-0 {
> +            #mbox-cells = <1>;
> +        };
> +
> +        remoteproc@5000000 {
> +            compatible = "ti,am64-m4fss";
> +            reg = <0x00 0x5000000 0x00 0x30000>,
> +                  <0x00 0x5040000 0x00 0x10000>;
> +            reg-names = "iram", "dram";
> +            ti,sci = <&dmsc>;
> +            ti,sci-dev-id = <9>;
> +            ti,sci-proc-ids = <0x18 0xff>;
> +            resets = <&k3_reset 9 1>;
> +            firmware-name = "am62-mcu-m4f0_0-fw";
> +            mboxes = <&mailbox0_cluster0>, <&mbox_m4_0>;
> +            memory-region = <&mcu_m4fss_dma_memory_region>,
> +                            <&mcu_m4fss_memory_region>;
> +            sram = <&oc_sram>;
> +         };
> +    };
> -- 
> 2.34.1
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v7 2/5] remoteproc: k3: Move out data structures common with M4 driver

[Hari Nagalla]

From: Martyn Welch <martyn.welch@collabora.com>

We will be adding the M4F driver which shares a lot of commonality
with the DSP driver. Common data structures are introduced here.

Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
---
Changes since v5:
 - Created a separate patch for data structures to ease review

Changes since v6:
 - Reworded 'split' to 'move' as the common data structures between
   DSP and M4 remote rpoc drivers are moved into common driver.

link to v6:
https://lore.kernel.org/all/20230913111644.29889-3-hnagalla@ti.com/

 drivers/remoteproc/ti_k3_common.h | 107 ++++++++++++++++++++++++++++++
 1 file changed, 107 insertions(+)
 create mode 100644 drivers/remoteproc/ti_k3_common.h

diff --git a/drivers/remoteproc/ti_k3_common.h b/drivers/remoteproc/ti_k3_common.h
new file mode 100644
index 000000000000..f1bab83dd0fc
--- /dev/null
+++ b/drivers/remoteproc/ti_k3_common.h
@@ -0,0 +1,107 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * TI K3 Remote Processor(s) driver common code
+ *
+ * Refactored from ti_k3_dsp_remoteproc.c.
+ *
+ * ti_k3_dsp_remoteproc.c:
+ * Copyright (C) 2018-2022 Texas Instruments Incorporated - https://www.ti.com/
+ *	Suman Anna <s-anna@ti.com>
+ */
+
+#ifndef REMOTEPROC_TI_K3_COMMON_H
+#define REMOTEPROC_TI_K3_COMMON_H
+
+#define KEYSTONE_RPROC_LOCAL_ADDRESS_MASK	(SZ_16M - 1)
+
+/**
+ * struct k3_rproc_mem - internal memory structure
+ * @cpu_addr: MPU virtual address of the memory region
+ * @bus_addr: Bus address used to access the memory region
+ * @dev_addr: Device address of the memory region from remote processor view
+ * @size: Size of the memory region
+ */
+struct k3_rproc_mem {
+	void __iomem *cpu_addr;
+	phys_addr_t bus_addr;
+	u32 dev_addr;
+	size_t size;
+};
+
+/**
+ * struct k3_rproc_mem_data - memory definitions for a remote processor
+ * @name: name for this memory entry
+ * @dev_addr: device address for the memory entry
+ */
+struct k3_rproc_mem_data {
+	const char *name;
+	const u32 dev_addr;
+};
+
+/**
+ * struct k3_rproc_dev_data - device data structure for a remote processor
+ * @mems: pointer to memory definitions for a remote processor
+ * @num_mems: number of memory regions in @mems
+ * @boot_align_addr: boot vector address alignment granularity
+ * @uses_lreset: flag to denote the need for local reset management
+ */
+struct k3_rproc_dev_data {
+	const struct k3_rproc_mem_data *mems;
+	u32 num_mems;
+	u32 boot_align_addr;
+	bool uses_lreset;
+};
+
+/**
+ * struct k3_rproc - k3 remote processor driver structure
+ * @dev: cached device pointer
+ * @rproc: remoteproc device handle
+ * @mem: internal memory regions data
+ * @num_mems: number of internal memory regions
+ * @rmem: reserved memory regions data
+ * @num_rmems: number of reserved memory regions
+ * @reset: reset control handle
+ * @data: pointer to device data
+ * @tsp: TI-SCI processor control handle
+ * @ti_sci: TI-SCI handle
+ * @ti_sci_id: TI-SCI device identifier
+ * @mbox: mailbox channel handle
+ * @client: mailbox client to request the mailbox channel
+ */
+struct k3_rproc {
+	struct device *dev;
+	struct rproc *rproc;
+	struct k3_rproc_mem *mem;
+	int num_mems;
+	struct k3_rproc_mem *sram;
+	int num_sram;
+	struct k3_rproc_mem *rmem;
+	int num_rmems;
+	struct reset_control *reset;
+	const struct k3_rproc_dev_data *data;
+	struct ti_sci_proc *tsp;
+	const struct ti_sci_handle *ti_sci;
+	u32 ti_sci_id;
+	struct mbox_chan *mbox;
+	struct mbox_client client;
+};
+
+void k3_rproc_kick(struct rproc *rproc, int vqid);
+int k3_rproc_reset(struct k3_rproc *kproc);
+int k3_rproc_release(struct k3_rproc *kproc);
+int k3_rproc_request_mbox(struct rproc *rproc);
+int k3_rproc_prepare(struct rproc *rproc);
+int k3_rproc_unprepare(struct rproc *rproc);
+struct resource_table *k3_get_loaded_rsc_table(struct rproc *rproc,
+					       size_t *rsc_table_sz);
+void *k3_rproc_da_to_va(struct rproc *rproc, u64 da, size_t len,
+			bool *is_iomem);
+int k3_rproc_of_get_memories(struct platform_device *pdev,
+			     struct k3_rproc *kproc);
+int k3_rproc_of_get_sram_memories(struct platform_device *pdev,
+			     struct k3_rproc *kproc);
+int k3_reserved_mem_init(struct k3_rproc *kproc);
+void k3_reserved_mem_exit(struct k3_rproc *kproc);
+struct ti_sci_proc *k3_rproc_of_get_tsp(struct device *dev,
+					const struct ti_sci_handle *sci);
+#endif /* REMOTEPROC_TI_K3_COMMON_H */
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v7 2/5] remoteproc: k3: Move out data structures common with M4 driver

[Andrew Davis]

On 2/2/24 11:55 AM, Hari Nagalla wrote:
> From: Martyn Welch <martyn.welch@collabora.com>
> 
> We will be adding the M4F driver which shares a lot of commonality
> with the DSP driver. Common data structures are introduced here.
> 
> Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
> Signed-off-by: Hari Nagalla <hnagalla@ti.com>
> ---
> Changes since v5:
>   - Created a separate patch for data structures to ease review
> 
> Changes since v6:
>   - Reworded 'split' to 'move' as the common data structures between
>     DSP and M4 remote rpoc drivers are moved into common driver.
> 

Is this a joke? In v6 Krzysztof commented the following:

> Where is the split? I see only addition here.
> 
> Where is the usage of this header? This is basically dead code. Don't
> add dead code, but instead actually move the structures here! Move is
> cut and paste, not just paste.

Instead of changing the patch in any way to address this comment you
just replaced the word 'split' to 'move' in the commit subject.. Maybe
no one will notice this is all still dead code since you didn't say the
word 'split' anymore..

Andrew

> link to v6:
> https://lore.kernel.org/all/20230913111644.29889-3-hnagalla@ti.com/
> 
>   drivers/remoteproc/ti_k3_common.h | 107 ++++++++++++++++++++++++++++++
>   1 file changed, 107 insertions(+)
>   create mode 100644 drivers/remoteproc/ti_k3_common.h
> 
> diff --git a/drivers/remoteproc/ti_k3_common.h b/drivers/remoteproc/ti_k3_common.h
> new file mode 100644
> index 000000000000..f1bab83dd0fc
> --- /dev/null
> +++ b/drivers/remoteproc/ti_k3_common.h
> @@ -0,0 +1,107 @@
> +/* SPDX-License-Identifier: GPL-2.0-only */
> +/*
> + * TI K3 Remote Processor(s) driver common code
> + *
> + * Refactored from ti_k3_dsp_remoteproc.c.
> + *
> + * ti_k3_dsp_remoteproc.c:
> + * Copyright (C) 2018-2022 Texas Instruments Incorporated - https://www.ti.com/
> + *	Suman Anna <s-anna@ti.com>
> + */
> +
> +#ifndef REMOTEPROC_TI_K3_COMMON_H
> +#define REMOTEPROC_TI_K3_COMMON_H
> +
> +#define KEYSTONE_RPROC_LOCAL_ADDRESS_MASK	(SZ_16M - 1)
> +
> +/**
> + * struct k3_rproc_mem - internal memory structure
> + * @cpu_addr: MPU virtual address of the memory region
> + * @bus_addr: Bus address used to access the memory region
> + * @dev_addr: Device address of the memory region from remote processor view
> + * @size: Size of the memory region
> + */
> +struct k3_rproc_mem {
> +	void __iomem *cpu_addr;
> +	phys_addr_t bus_addr;
> +	u32 dev_addr;
> +	size_t size;
> +};
> +
> +/**
> + * struct k3_rproc_mem_data - memory definitions for a remote processor
> + * @name: name for this memory entry
> + * @dev_addr: device address for the memory entry
> + */
> +struct k3_rproc_mem_data {
> +	const char *name;
> +	const u32 dev_addr;
> +};
> +
> +/**
> + * struct k3_rproc_dev_data - device data structure for a remote processor
> + * @mems: pointer to memory definitions for a remote processor
> + * @num_mems: number of memory regions in @mems
> + * @boot_align_addr: boot vector address alignment granularity
> + * @uses_lreset: flag to denote the need for local reset management
> + */
> +struct k3_rproc_dev_data {
> +	const struct k3_rproc_mem_data *mems;
> +	u32 num_mems;
> +	u32 boot_align_addr;
> +	bool uses_lreset;
> +};
> +
> +/**
> + * struct k3_rproc - k3 remote processor driver structure
> + * @dev: cached device pointer
> + * @rproc: remoteproc device handle
> + * @mem: internal memory regions data
> + * @num_mems: number of internal memory regions
> + * @rmem: reserved memory regions data
> + * @num_rmems: number of reserved memory regions
> + * @reset: reset control handle
> + * @data: pointer to device data
> + * @tsp: TI-SCI processor control handle
> + * @ti_sci: TI-SCI handle
> + * @ti_sci_id: TI-SCI device identifier
> + * @mbox: mailbox channel handle
> + * @client: mailbox client to request the mailbox channel
> + */
> +struct k3_rproc {
> +	struct device *dev;
> +	struct rproc *rproc;
> +	struct k3_rproc_mem *mem;
> +	int num_mems;
> +	struct k3_rproc_mem *sram;
> +	int num_sram;
> +	struct k3_rproc_mem *rmem;
> +	int num_rmems;
> +	struct reset_control *reset;
> +	const struct k3_rproc_dev_data *data;
> +	struct ti_sci_proc *tsp;
> +	const struct ti_sci_handle *ti_sci;
> +	u32 ti_sci_id;
> +	struct mbox_chan *mbox;
> +	struct mbox_client client;
> +};
> +
> +void k3_rproc_kick(struct rproc *rproc, int vqid);
> +int k3_rproc_reset(struct k3_rproc *kproc);
> +int k3_rproc_release(struct k3_rproc *kproc);
> +int k3_rproc_request_mbox(struct rproc *rproc);
> +int k3_rproc_prepare(struct rproc *rproc);
> +int k3_rproc_unprepare(struct rproc *rproc);
> +struct resource_table *k3_get_loaded_rsc_table(struct rproc *rproc,
> +					       size_t *rsc_table_sz);
> +void *k3_rproc_da_to_va(struct rproc *rproc, u64 da, size_t len,
> +			bool *is_iomem);
> +int k3_rproc_of_get_memories(struct platform_device *pdev,
> +			     struct k3_rproc *kproc);
> +int k3_rproc_of_get_sram_memories(struct platform_device *pdev,
> +			     struct k3_rproc *kproc);
> +int k3_reserved_mem_init(struct k3_rproc *kproc);
> +void k3_reserved_mem_exit(struct k3_rproc *kproc);
> +struct ti_sci_proc *k3_rproc_of_get_tsp(struct device *dev,
> +					const struct ti_sci_handle *sci);
> +#endif /* REMOTEPROC_TI_K3_COMMON_H */

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v7 3/5] remoteproc: k3: Move out functions common with M4 driver

[Hari Nagalla]

From: Martyn Welch <martyn.welch@collabora.com>

In the next commit we will be adding the M4F driver which shares a lot of
commonality with the DSP driver. Move this shared functionality out so
that it can be used by both drivers.

Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
---
Changes since v2:
 - New patch (reordered refactored from v2)

Changes since v3:
 - Removed "ipc_only" element from k3_rproc structure
 - Refactored to bring 3 more common functions

Changes since v4:
 - None

Changes since v5:
 - Rearranged the functions order to match with the functions in
   ti_k3_dsp_remoteproc.c to ease review.

Changes since v6:
 - Generated patch with -M/-B/-C options

link to v6:
https://lore.kernel.org/all/20230913111644.29889-4-hnagalla@ti.com/

 drivers/remoteproc/Makefile               |    2 +-
 drivers/remoteproc/ti_k3_common.c         |  583 ++++++++++
 drivers/remoteproc/ti_k3_dsp_remoteproc.c | 1277 ++++++---------------
 3 files changed, 952 insertions(+), 910 deletions(-)
 create mode 100644 drivers/remoteproc/ti_k3_common.c
 rewrite drivers/remoteproc/ti_k3_dsp_remoteproc.c (67%)

diff --git a/drivers/remoteproc/Makefile b/drivers/remoteproc/Makefile
index 91314a9b43ce..55c552e27a45 100644
--- a/drivers/remoteproc/Makefile
+++ b/drivers/remoteproc/Makefile
@@ -36,6 +36,6 @@ obj-$(CONFIG_RCAR_REMOTEPROC)		+= rcar_rproc.o
 obj-$(CONFIG_ST_REMOTEPROC)		+= st_remoteproc.o
 obj-$(CONFIG_ST_SLIM_REMOTEPROC)	+= st_slim_rproc.o
 obj-$(CONFIG_STM32_RPROC)		+= stm32_rproc.o
-obj-$(CONFIG_TI_K3_DSP_REMOTEPROC)	+= ti_k3_dsp_remoteproc.o
+obj-$(CONFIG_TI_K3_DSP_REMOTEPROC)	+= ti_k3_dsp_remoteproc.o ti_k3_common.o
 obj-$(CONFIG_TI_K3_R5_REMOTEPROC)	+= ti_k3_r5_remoteproc.o
 obj-$(CONFIG_XLNX_R5_REMOTEPROC)	+= xlnx_r5_remoteproc.o
diff --git a/drivers/remoteproc/ti_k3_common.c b/drivers/remoteproc/ti_k3_common.c
new file mode 100644
index 000000000000..62c7c5dba78a
--- /dev/null
+++ b/drivers/remoteproc/ti_k3_common.c
@@ -0,0 +1,583 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * TI K3 Remote Processor(s) driver common code
+ *
+ * Refactored from ti_k3_dsp_remoteproc.c.
+ *
+ * ti_k3_dsp_remoteproc.c:
+ * Copyright (C) 2018-2022 Texas Instruments Incorporated - https://www.ti.com/
+ *	Suman Anna <s-anna@ti.com>
+ */
+
+#include <linux/io.h>
+#include <linux/mailbox_client.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+#include <linux/of_reserved_mem.h>
+#include <linux/omap-mailbox.h>
+#include <linux/platform_device.h>
+#include <linux/remoteproc.h>
+#include <linux/reset.h>
+#include <linux/slab.h>
+
+#include "omap_remoteproc.h"
+#include "remoteproc_internal.h"
+#include "ti_sci_proc.h"
+#include "ti_k3_common.h"
+
+/**
+ * k3_rproc_mbox_callback() - inbound mailbox message handler
+ * @client: mailbox client pointer used for requesting the mailbox channel
+ * @data: mailbox payload
+ *
+ * This handler is invoked by the K3 mailbox driver whenever a mailbox
+ * message is received. Usually, the mailbox payload simply contains
+ * the index of the virtqueue that is kicked by the remote processor,
+ * and we let remoteproc core handle it.
+ *
+ * In addition to virtqueue indices, we also have some out-of-band values
+ * that indicate different events. Those values are deliberately very
+ * large so they don't coincide with virtqueue indices.
+ */
+static void k3_rproc_mbox_callback(struct mbox_client *client, void *data)
+{
+	struct k3_rproc *kproc = container_of(client, struct k3_rproc,
+						  client);
+	struct device *dev = kproc->rproc->dev.parent;
+	const char *name = kproc->rproc->name;
+	u32 msg = omap_mbox_message(data);
+
+	dev_dbg(dev, "mbox msg: 0x%x\n", msg);
+
+	switch (msg) {
+	case RP_MBOX_CRASH:
+		/*
+		 * remoteproc detected an exception, but error recovery is not
+		 * supported. So, just log this for now
+		 */
+		dev_err(dev, "K3 rproc %s crashed\n", name);
+		break;
+	case RP_MBOX_ECHO_REPLY:
+		dev_info(dev, "received echo reply from %s\n", name);
+		break;
+	default:
+		/* silently handle all other valid messages */
+		if (msg >= RP_MBOX_READY && msg < RP_MBOX_END_MSG)
+			return;
+		if (msg > kproc->rproc->max_notifyid) {
+			dev_dbg(dev, "dropping unknown message 0x%x", msg);
+			return;
+		}
+		/* msg contains the index of the triggered vring */
+		if (rproc_vq_interrupt(kproc->rproc, msg) == IRQ_NONE)
+			dev_dbg(dev, "no message was found in vqid %d\n", msg);
+	}
+}
+
+/*
+ * Kick the remote processor to notify about pending unprocessed messages.
+ * The vqid usage is not used and is inconsequential, as the kick is performed
+ * through a simulated GPIO (a bit in an IPC interrupt-triggering register),
+ * the remote processor is expected to process both its Tx and Rx virtqueues.
+ */
+void k3_rproc_kick(struct rproc *rproc, int vqid)
+{
+	struct k3_rproc *kproc = rproc->priv;
+	struct device *dev = rproc->dev.parent;
+	mbox_msg_t msg = (mbox_msg_t)vqid;
+	int ret;
+
+	/* send the index of the triggered virtqueue in the mailbox payload */
+	ret = mbox_send_message(kproc->mbox, (void *)msg);
+	if (ret < 0)
+		dev_err(dev, "failed to send mailbox message, status = %d\n",
+			ret);
+}
+EXPORT_SYMBOL_GPL(k3_rproc_kick);
+
+/* Put the remote processor into reset */
+int k3_rproc_reset(struct k3_rproc *kproc)
+{
+	struct device *dev = kproc->dev;
+	int ret;
+
+	ret = reset_control_assert(kproc->reset);
+	if (ret) {
+		dev_err(dev, "local-reset assert failed, ret = %d\n", ret);
+		return ret;
+	}
+
+	if (kproc->data->uses_lreset)
+		return ret;
+
+	ret = kproc->ti_sci->ops.dev_ops.put_device(kproc->ti_sci,
+						    kproc->ti_sci_id);
+	if (ret) {
+		dev_err(dev, "module-reset assert failed, ret = %d\n", ret);
+		if (reset_control_deassert(kproc->reset))
+			dev_warn(dev, "local-reset deassert back failed\n");
+	}
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(k3_rproc_reset);
+
+/* Release the remote processor from reset */
+int k3_rproc_release(struct k3_rproc *kproc)
+{
+	struct device *dev = kproc->dev;
+	int ret;
+
+	if (kproc->data->uses_lreset)
+		goto lreset;
+
+	ret = kproc->ti_sci->ops.dev_ops.get_device(kproc->ti_sci,
+						    kproc->ti_sci_id);
+	if (ret) {
+		dev_err(dev, "module-reset deassert failed, ret = %d\n", ret);
+		return ret;
+	}
+
+lreset:
+	ret = reset_control_deassert(kproc->reset);
+	if (ret) {
+		dev_err(dev, "local-reset deassert failed, ret = %d\n", ret);
+		if (kproc->ti_sci->ops.dev_ops.put_device(kproc->ti_sci,
+							  kproc->ti_sci_id))
+			dev_warn(dev, "module-reset assert back failed\n");
+	}
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(k3_rproc_release);
+
+int k3_rproc_request_mbox(struct rproc *rproc)
+{
+	struct k3_rproc *kproc = rproc->priv;
+	struct mbox_client *client = &kproc->client;
+	struct device *dev = kproc->dev;
+	int ret;
+
+	client->dev = dev;
+	client->tx_done = NULL;
+	client->rx_callback = k3_rproc_mbox_callback;
+	client->tx_block = false;
+	client->knows_txdone = false;
+
+	kproc->mbox = mbox_request_channel(client, 0);
+	if (IS_ERR(kproc->mbox)) {
+		ret = -EBUSY;
+		dev_err(dev, "mbox_request_channel failed: %ld\n",
+			PTR_ERR(kproc->mbox));
+		return ret;
+	}
+
+	/*
+	 * Ping the remote processor, this is only for sanity-sake for now;
+	 * there is no functional effect whatsoever.
+	 *
+	 * Note that the reply will _not_ arrive immediately: this message
+	 * will wait in the mailbox fifo until the remote processor is booted.
+	 */
+	ret = mbox_send_message(kproc->mbox, (void *)RP_MBOX_ECHO_REQUEST);
+	if (ret < 0) {
+		dev_err(dev, "mbox_send_message failed: %d\n", ret);
+		mbox_free_channel(kproc->mbox);
+		return ret;
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(k3_rproc_request_mbox);
+
+/*
+ * The DSP and MCU cores have a local reset that affects only the CPU, and a
+ * generic module reset that powers on the device and allows the internal
+ * memories to be accessed while the local reset is asserted. This function is
+ * used to release the global reset on remote cores to allow loading into the
+ * internal RAMs. The .prepare() ops is invoked by remoteproc core before any
+ * firmware loading, and is followed by the .start() ops after loading to
+ * actually let the remote cores to run. This callback is invoked only in
+ * remoteproc mode.
+ */
+int k3_rproc_prepare(struct rproc *rproc)
+{
+	struct k3_rproc *kproc = rproc->priv;
+	struct device *dev = kproc->dev;
+	int ret;
+
+	ret = kproc->ti_sci->ops.dev_ops.get_device(kproc->ti_sci,
+						    kproc->ti_sci_id);
+	if (ret)
+		dev_err(dev, "module-reset deassert failed, cannot enable internal RAM loading, ret = %d\n",
+			ret);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(k3_rproc_prepare);
+
+/*
+ * This function implements the .unprepare() ops and performs the complimentary
+ * operations to that of the .prepare() ops. The function is used to assert the
+ * global reset on applicable DSP, MCU cores. This completes the second portion of
+ * powering down the remote core. The cores themselves are only halted in the
+ * .stop() callback through the local reset, and the .unprepare() ops is invoked
+ * by the remoteproc core after the remoteproc is stopped to balance the global
+ * reset. This callback is invoked only in remoteproc mode.
+ */
+int k3_rproc_unprepare(struct rproc *rproc)
+{
+	struct k3_rproc *kproc = rproc->priv;
+	struct device *dev = kproc->dev;
+	int ret;
+
+	ret = kproc->ti_sci->ops.dev_ops.put_device(kproc->ti_sci,
+						    kproc->ti_sci_id);
+	if (ret)
+		dev_err(dev, "module-reset assert failed, ret = %d\n", ret);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(k3_rproc_unprepare);
+
+/*
+ * This function implements the .get_loaded_rsc_table() callback and is used
+ * to provide the resource table for a booted remote processor in IPC-only
+ * mode. The remote processor firmwares follow a design-by-contract approach
+ * and are expected to have the resource table at the base of the DDR region
+ * reserved for firmware usage. This provides flexibility for the remote
+ * processor to be booted by different bootloaders that may or may not have the
+ * ability to publish the resource table address and size through a DT
+ * property.
+ */
+struct resource_table *k3_get_loaded_rsc_table(struct rproc *rproc,
+					       size_t *rsc_table_sz)
+{
+	struct k3_rproc *kproc = rproc->priv;
+	struct device *dev = kproc->dev;
+
+	if (!kproc->rmem[0].cpu_addr) {
+		dev_err(dev, "memory-region #1 does not exist, loaded rsc table can't be found");
+		return ERR_PTR(-ENOMEM);
+	}
+
+	/*
+	 * NOTE: The resource table size is currently hard-coded to a maximum
+	 * of 256 bytes. The most common resource table usage for K3 firmwares
+	 * is to only have the vdev resource entry and an optional trace entry.
+	 * The exact size could be computed based on resource table address, but
+	 * the hard-coded value suffices to support the IPC-only mode.
+	 */
+	*rsc_table_sz = 256;
+	return (struct resource_table *)kproc->rmem[0].cpu_addr;
+}
+EXPORT_SYMBOL_GPL(k3_get_loaded_rsc_table);
+
+/*
+ * Custom function to translate a remote processor device address (internal
+ * RAMs only) to a kernel virtual address.  The remote processors can access
+ * their RAMs at either an internal address visible only from a remote
+ * processor, or at the SoC-level bus address. Both these addresses need to be
+ * looked through for translation. The translated addresses can be used either
+ * by the remoteproc core for loading (when using kernel remoteproc loader), or
+ * by any rpmsg bus drivers.
+ */
+void *k3_rproc_da_to_va(struct rproc *rproc, u64 da, size_t len, bool *is_iomem)
+{
+	struct k3_rproc *kproc = rproc->priv;
+	void __iomem *va = NULL;
+	phys_addr_t bus_addr;
+	u32 dev_addr, offset;
+	size_t size;
+	int i;
+
+	if (len == 0)
+		return NULL;
+
+	for (i = 0; i < kproc->num_mems; i++) {
+		bus_addr = kproc->mem[i].bus_addr;
+		dev_addr = kproc->mem[i].dev_addr;
+		size = kproc->mem[i].size;
+
+		if (da < KEYSTONE_RPROC_LOCAL_ADDRESS_MASK) {
+			/* handle remote-view addresses */
+			if (da >= dev_addr &&
+			    ((da + len) <= (dev_addr + size))) {
+				offset = da - dev_addr;
+				va = kproc->mem[i].cpu_addr + offset;
+				return (__force void *)va;
+			}
+		} else {
+			/* handle SoC-view addresses */
+			if (da >= bus_addr &&
+			    (da + len) <= (bus_addr + size)) {
+				offset = da - bus_addr;
+				va = kproc->mem[i].cpu_addr + offset;
+				return (__force void *)va;
+			}
+		}
+	}
+
+	/* handle any SRAM regions using SoC-view addresses */
+	for (i = 0; i < kproc->num_sram; i++) {
+		dev_addr = kproc->sram[i].dev_addr;
+		size = kproc->sram[i].size;
+
+		if (da >= dev_addr && ((da + len) <= (dev_addr + size))) {
+			offset = da - dev_addr;
+			va = kproc->sram[i].cpu_addr + offset;
+			return (__force void *)va;
+		}
+	}
+
+	/* handle static DDR reserved memory regions */
+	for (i = 0; i < kproc->num_rmems; i++) {
+		dev_addr = kproc->rmem[i].dev_addr;
+		size = kproc->rmem[i].size;
+
+		if (da >= dev_addr && ((da + len) <= (dev_addr + size))) {
+			offset = da - dev_addr;
+			va = kproc->rmem[i].cpu_addr + offset;
+			return (__force void *)va;
+		}
+	}
+
+	return NULL;
+}
+EXPORT_SYMBOL_GPL(k3_rproc_da_to_va);
+
+int k3_rproc_of_get_memories(struct platform_device *pdev,
+			     struct k3_rproc *kproc)
+{
+	const struct k3_rproc_dev_data *data = kproc->data;
+	struct device *dev = &pdev->dev;
+	struct resource *res;
+	int num_mems = 0;
+	int i;
+
+	num_mems = kproc->data->num_mems;
+	kproc->mem = devm_kcalloc(kproc->dev, num_mems,
+				  sizeof(*kproc->mem), GFP_KERNEL);
+	if (!kproc->mem)
+		return -ENOMEM;
+
+	for (i = 0; i < num_mems; i++) {
+		res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
+						   data->mems[i].name);
+		if (!res) {
+			dev_err(dev, "found no memory resource for %s\n",
+				data->mems[i].name);
+			return -EINVAL;
+		}
+		if (!devm_request_mem_region(dev, res->start,
+					     resource_size(res),
+					     dev_name(dev))) {
+			dev_err(dev, "could not request %s region for resource\n",
+				data->mems[i].name);
+			return -EBUSY;
+		}
+
+		kproc->mem[i].cpu_addr = devm_ioremap_wc(dev, res->start,
+							 resource_size(res));
+		if (!kproc->mem[i].cpu_addr) {
+			dev_err(dev, "failed to map %s memory\n",
+				data->mems[i].name);
+			return -ENOMEM;
+		}
+		kproc->mem[i].bus_addr = res->start;
+		kproc->mem[i].dev_addr = data->mems[i].dev_addr;
+		kproc->mem[i].size = resource_size(res);
+
+		dev_dbg(dev, "memory %8s: bus addr %pa size 0x%zx va %pK da 0x%x\n",
+			data->mems[i].name, &kproc->mem[i].bus_addr,
+			kproc->mem[i].size, kproc->mem[i].cpu_addr,
+			kproc->mem[i].dev_addr);
+	}
+	kproc->num_mems = num_mems;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(k3_rproc_of_get_memories);
+
+int k3_rproc_of_get_sram_memories(struct platform_device *pdev,
+					   struct k3_rproc *kproc)
+{
+	struct device_node *np = pdev->dev.of_node;
+	struct device *dev = &pdev->dev;
+	struct device_node *sram_np;
+	struct resource res;
+	int num_sram;
+	int i, ret;
+
+	num_sram = of_property_count_elems_of_size(np, "sram", sizeof(phandle));
+	if (num_sram <= 0) {
+		dev_dbg(dev, "device does not use reserved on-chip memories, num_sram = %d\n",
+			num_sram);
+		return 0;
+	}
+
+	kproc->sram = devm_kcalloc(dev, num_sram, sizeof(*kproc->sram), GFP_KERNEL);
+	if (!kproc->sram)
+		return -ENOMEM;
+
+	for (i = 0; i < num_sram; i++) {
+		sram_np = of_parse_phandle(np, "sram", i);
+		if (!sram_np)
+			return -EINVAL;
+
+		if (!of_device_is_available(sram_np)) {
+			of_node_put(sram_np);
+			return -EINVAL;
+		}
+
+		ret = of_address_to_resource(sram_np, 0, &res);
+		of_node_put(sram_np);
+		if (ret)
+			return -EINVAL;
+
+		kproc->sram[i].bus_addr = res.start;
+		kproc->sram[i].dev_addr = res.start;
+		kproc->sram[i].size = resource_size(&res);
+		kproc->sram[i].cpu_addr = devm_ioremap_wc(dev, res.start,
+							 resource_size(&res));
+		if (!kproc->sram[i].cpu_addr) {
+			dev_err(dev, "failed to parse and map sram%d memory at %pad\n",
+				i, &res.start);
+			return -ENOMEM;
+		}
+
+		dev_dbg(dev, "memory sram%d: bus addr %pa size 0x%zx va %pK da 0x%x\n",
+			i, &kproc->sram[i].bus_addr,
+			kproc->sram[i].size, kproc->sram[i].cpu_addr,
+			kproc->sram[i].dev_addr);
+	}
+	kproc->num_sram = num_sram;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(k3_rproc_of_get_sram_memories);
+int k3_reserved_mem_init(struct k3_rproc *kproc)
+{
+	struct device *dev = kproc->dev;
+	struct device_node *np = dev->of_node;
+	struct device_node *rmem_np;
+	struct reserved_mem *rmem;
+	int num_rmems;
+	int ret, i;
+
+	num_rmems = of_property_count_elems_of_size(np, "memory-region",
+						    sizeof(phandle));
+	if (num_rmems <= 0) {
+		dev_err(dev, "device does not reserved memory regions, ret = %d\n",
+			num_rmems);
+		return -EINVAL;
+	}
+	if (num_rmems < 2) {
+		dev_err(dev, "device needs at least two memory regions to be defined, num = %d\n",
+			num_rmems);
+		return -EINVAL;
+	}
+
+	/* use reserved memory region 0 for vring DMA allocations */
+	ret = of_reserved_mem_device_init_by_idx(dev, np, 0);
+	if (ret) {
+		dev_err(dev, "device cannot initialize DMA pool, ret = %d\n",
+			ret);
+		return ret;
+	}
+
+	num_rmems--;
+	kproc->rmem = kcalloc(num_rmems, sizeof(*kproc->rmem), GFP_KERNEL);
+	if (!kproc->rmem) {
+		ret = -ENOMEM;
+		goto release_rmem;
+	}
+
+	/* use remaining reserved memory regions for static carveouts */
+	for (i = 0; i < num_rmems; i++) {
+		rmem_np = of_parse_phandle(np, "memory-region", i + 1);
+		if (!rmem_np) {
+			ret = -EINVAL;
+			goto unmap_rmem;
+		}
+
+		rmem = of_reserved_mem_lookup(rmem_np);
+		if (!rmem) {
+			of_node_put(rmem_np);
+			ret = -EINVAL;
+			goto unmap_rmem;
+		}
+		of_node_put(rmem_np);
+
+		kproc->rmem[i].bus_addr = rmem->base;
+		/* 64-bit address regions currently not supported */
+		kproc->rmem[i].dev_addr = (u32)rmem->base;
+		kproc->rmem[i].size = rmem->size;
+		kproc->rmem[i].cpu_addr = ioremap_wc(rmem->base, rmem->size);
+		if (!kproc->rmem[i].cpu_addr) {
+			dev_err(dev, "failed to map reserved memory#%d at %pa of size %pa\n",
+				i + 1, &rmem->base, &rmem->size);
+			ret = -ENOMEM;
+			goto unmap_rmem;
+		}
+
+		dev_dbg(dev, "reserved memory%d: bus addr %pa size 0x%zx va %pK da 0x%x\n",
+			i + 1, &kproc->rmem[i].bus_addr,
+			kproc->rmem[i].size, kproc->rmem[i].cpu_addr,
+			kproc->rmem[i].dev_addr);
+	}
+	kproc->num_rmems = num_rmems;
+
+	return 0;
+
+unmap_rmem:
+	for (i--; i >= 0; i--)
+		iounmap(kproc->rmem[i].cpu_addr);
+	kfree(kproc->rmem);
+release_rmem:
+	of_reserved_mem_device_release(kproc->dev);
+	return ret;
+}
+EXPORT_SYMBOL_GPL(k3_reserved_mem_init);
+
+void k3_reserved_mem_exit(struct k3_rproc *kproc)
+{
+	int i;
+
+	for (i = 0; i < kproc->num_rmems; i++)
+		iounmap(kproc->rmem[i].cpu_addr);
+	kfree(kproc->rmem);
+
+	of_reserved_mem_device_release(kproc->dev);
+}
+EXPORT_SYMBOL_GPL(k3_reserved_mem_exit);
+
+struct ti_sci_proc *k3_rproc_of_get_tsp(struct device *dev,
+					const struct ti_sci_handle *sci)
+{
+	struct ti_sci_proc *tsp;
+	u32 temp[2];
+	int ret;
+
+	ret = of_property_read_u32_array(dev->of_node, "ti,sci-proc-ids",
+					 temp, 2);
+	if (ret < 0)
+		return ERR_PTR(ret);
+
+	tsp = kzalloc(sizeof(*tsp), GFP_KERNEL);
+	if (!tsp)
+		return ERR_PTR(-ENOMEM);
+
+	tsp->dev = dev;
+	tsp->sci = sci;
+	tsp->ops = &sci->ops.proc_ops;
+	tsp->proc_id = temp[0];
+	tsp->host_id = temp[1];
+
+	return tsp;
+}
+EXPORT_SYMBOL_GPL(k3_rproc_of_get_tsp);
+
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("TI K3 common Remoteproc support");
diff --git a/drivers/remoteproc/ti_k3_dsp_remoteproc.c b/drivers/remoteproc/ti_k3_dsp_remoteproc.c
dissimilarity index 67%
index ab882e3b7130..ebe23fc5ca44 100644
--- a/drivers/remoteproc/ti_k3_dsp_remoteproc.c
+++ b/drivers/remoteproc/ti_k3_dsp_remoteproc.c
@@ -1,909 +1,368 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * TI K3 DSP Remote Processor(s) driver
- *
- * Copyright (C) 2018-2022 Texas Instruments Incorporated - https://www.ti.com/
- *	Suman Anna <s-anna@ti.com>
- */
-
-#include <linux/io.h>
-#include <linux/mailbox_client.h>
-#include <linux/module.h>
-#include <linux/of.h>
-#include <linux/of_reserved_mem.h>
-#include <linux/omap-mailbox.h>
-#include <linux/platform_device.h>
-#include <linux/remoteproc.h>
-#include <linux/reset.h>
-#include <linux/slab.h>
-
-#include "omap_remoteproc.h"
-#include "remoteproc_internal.h"
-#include "ti_sci_proc.h"
-
-#define KEYSTONE_RPROC_LOCAL_ADDRESS_MASK	(SZ_16M - 1)
-
-/**
- * struct k3_dsp_mem - internal memory structure
- * @cpu_addr: MPU virtual address of the memory region
- * @bus_addr: Bus address used to access the memory region
- * @dev_addr: Device address of the memory region from DSP view
- * @size: Size of the memory region
- */
-struct k3_dsp_mem {
-	void __iomem *cpu_addr;
-	phys_addr_t bus_addr;
-	u32 dev_addr;
-	size_t size;
-};
-
-/**
- * struct k3_dsp_mem_data - memory definitions for a DSP
- * @name: name for this memory entry
- * @dev_addr: device address for the memory entry
- */
-struct k3_dsp_mem_data {
-	const char *name;
-	const u32 dev_addr;
-};
-
-/**
- * struct k3_dsp_dev_data - device data structure for a DSP
- * @mems: pointer to memory definitions for a DSP
- * @num_mems: number of memory regions in @mems
- * @boot_align_addr: boot vector address alignment granularity
- * @uses_lreset: flag to denote the need for local reset management
- */
-struct k3_dsp_dev_data {
-	const struct k3_dsp_mem_data *mems;
-	u32 num_mems;
-	u32 boot_align_addr;
-	bool uses_lreset;
-};
-
-/**
- * struct k3_dsp_rproc - k3 DSP remote processor driver structure
- * @dev: cached device pointer
- * @rproc: remoteproc device handle
- * @mem: internal memory regions data
- * @num_mems: number of internal memory regions
- * @rmem: reserved memory regions data
- * @num_rmems: number of reserved memory regions
- * @reset: reset control handle
- * @data: pointer to DSP-specific device data
- * @tsp: TI-SCI processor control handle
- * @ti_sci: TI-SCI handle
- * @ti_sci_id: TI-SCI device identifier
- * @mbox: mailbox channel handle
- * @client: mailbox client to request the mailbox channel
- */
-struct k3_dsp_rproc {
-	struct device *dev;
-	struct rproc *rproc;
-	struct k3_dsp_mem *mem;
-	int num_mems;
-	struct k3_dsp_mem *rmem;
-	int num_rmems;
-	struct reset_control *reset;
-	const struct k3_dsp_dev_data *data;
-	struct ti_sci_proc *tsp;
-	const struct ti_sci_handle *ti_sci;
-	u32 ti_sci_id;
-	struct mbox_chan *mbox;
-	struct mbox_client client;
-};
-
-/**
- * k3_dsp_rproc_mbox_callback() - inbound mailbox message handler
- * @client: mailbox client pointer used for requesting the mailbox channel
- * @data: mailbox payload
- *
- * This handler is invoked by the OMAP mailbox driver whenever a mailbox
- * message is received. Usually, the mailbox payload simply contains
- * the index of the virtqueue that is kicked by the remote processor,
- * and we let remoteproc core handle it.
- *
- * In addition to virtqueue indices, we also have some out-of-band values
- * that indicate different events. Those values are deliberately very
- * large so they don't coincide with virtqueue indices.
- */
-static void k3_dsp_rproc_mbox_callback(struct mbox_client *client, void *data)
-{
-	struct k3_dsp_rproc *kproc = container_of(client, struct k3_dsp_rproc,
-						  client);
-	struct device *dev = kproc->rproc->dev.parent;
-	const char *name = kproc->rproc->name;
-	u32 msg = omap_mbox_message(data);
-
-	dev_dbg(dev, "mbox msg: 0x%x\n", msg);
-
-	switch (msg) {
-	case RP_MBOX_CRASH:
-		/*
-		 * remoteproc detected an exception, but error recovery is not
-		 * supported. So, just log this for now
-		 */
-		dev_err(dev, "K3 DSP rproc %s crashed\n", name);
-		break;
-	case RP_MBOX_ECHO_REPLY:
-		dev_info(dev, "received echo reply from %s\n", name);
-		break;
-	default:
-		/* silently handle all other valid messages */
-		if (msg >= RP_MBOX_READY && msg < RP_MBOX_END_MSG)
-			return;
-		if (msg > kproc->rproc->max_notifyid) {
-			dev_dbg(dev, "dropping unknown message 0x%x", msg);
-			return;
-		}
-		/* msg contains the index of the triggered vring */
-		if (rproc_vq_interrupt(kproc->rproc, msg) == IRQ_NONE)
-			dev_dbg(dev, "no message was found in vqid %d\n", msg);
-	}
-}
-
-/*
- * Kick the remote processor to notify about pending unprocessed messages.
- * The vqid usage is not used and is inconsequential, as the kick is performed
- * through a simulated GPIO (a bit in an IPC interrupt-triggering register),
- * the remote processor is expected to process both its Tx and Rx virtqueues.
- */
-static void k3_dsp_rproc_kick(struct rproc *rproc, int vqid)
-{
-	struct k3_dsp_rproc *kproc = rproc->priv;
-	struct device *dev = rproc->dev.parent;
-	mbox_msg_t msg = (mbox_msg_t)vqid;
-	int ret;
-
-	/* send the index of the triggered virtqueue in the mailbox payload */
-	ret = mbox_send_message(kproc->mbox, (void *)msg);
-	if (ret < 0)
-		dev_err(dev, "failed to send mailbox message (%pe)\n",
-			ERR_PTR(ret));
-}
-
-/* Put the DSP processor into reset */
-static int k3_dsp_rproc_reset(struct k3_dsp_rproc *kproc)
-{
-	struct device *dev = kproc->dev;
-	int ret;
-
-	ret = reset_control_assert(kproc->reset);
-	if (ret) {
-		dev_err(dev, "local-reset assert failed (%pe)\n", ERR_PTR(ret));
-		return ret;
-	}
-
-	if (kproc->data->uses_lreset)
-		return ret;
-
-	ret = kproc->ti_sci->ops.dev_ops.put_device(kproc->ti_sci,
-						    kproc->ti_sci_id);
-	if (ret) {
-		dev_err(dev, "module-reset assert failed (%pe)\n", ERR_PTR(ret));
-		if (reset_control_deassert(kproc->reset))
-			dev_warn(dev, "local-reset deassert back failed\n");
-	}
-
-	return ret;
-}
-
-/* Release the DSP processor from reset */
-static int k3_dsp_rproc_release(struct k3_dsp_rproc *kproc)
-{
-	struct device *dev = kproc->dev;
-	int ret;
-
-	if (kproc->data->uses_lreset)
-		goto lreset;
-
-	ret = kproc->ti_sci->ops.dev_ops.get_device(kproc->ti_sci,
-						    kproc->ti_sci_id);
-	if (ret) {
-		dev_err(dev, "module-reset deassert failed (%pe)\n", ERR_PTR(ret));
-		return ret;
-	}
-
-lreset:
-	ret = reset_control_deassert(kproc->reset);
-	if (ret) {
-		dev_err(dev, "local-reset deassert failed, (%pe)\n", ERR_PTR(ret));
-		if (kproc->ti_sci->ops.dev_ops.put_device(kproc->ti_sci,
-							  kproc->ti_sci_id))
-			dev_warn(dev, "module-reset assert back failed\n");
-	}
-
-	return ret;
-}
-
-static int k3_dsp_rproc_request_mbox(struct rproc *rproc)
-{
-	struct k3_dsp_rproc *kproc = rproc->priv;
-	struct mbox_client *client = &kproc->client;
-	struct device *dev = kproc->dev;
-	int ret;
-
-	client->dev = dev;
-	client->tx_done = NULL;
-	client->rx_callback = k3_dsp_rproc_mbox_callback;
-	client->tx_block = false;
-	client->knows_txdone = false;
-
-	kproc->mbox = mbox_request_channel(client, 0);
-	if (IS_ERR(kproc->mbox)) {
-		ret = -EBUSY;
-		dev_err(dev, "mbox_request_channel failed: %ld\n",
-			PTR_ERR(kproc->mbox));
-		return ret;
-	}
-
-	/*
-	 * Ping the remote processor, this is only for sanity-sake for now;
-	 * there is no functional effect whatsoever.
-	 *
-	 * Note that the reply will _not_ arrive immediately: this message
-	 * will wait in the mailbox fifo until the remote processor is booted.
-	 */
-	ret = mbox_send_message(kproc->mbox, (void *)RP_MBOX_ECHO_REQUEST);
-	if (ret < 0) {
-		dev_err(dev, "mbox_send_message failed (%pe)\n", ERR_PTR(ret));
-		mbox_free_channel(kproc->mbox);
-		return ret;
-	}
-
-	return 0;
-}
-/*
- * The C66x DSP cores have a local reset that affects only the CPU, and a
- * generic module reset that powers on the device and allows the DSP internal
- * memories to be accessed while the local reset is asserted. This function is
- * used to release the global reset on C66x DSPs to allow loading into the DSP
- * internal RAMs. The .prepare() ops is invoked by remoteproc core before any
- * firmware loading, and is followed by the .start() ops after loading to
- * actually let the C66x DSP cores run. This callback is invoked only in
- * remoteproc mode.
- */
-static int k3_dsp_rproc_prepare(struct rproc *rproc)
-{
-	struct k3_dsp_rproc *kproc = rproc->priv;
-	struct device *dev = kproc->dev;
-	int ret;
-
-	ret = kproc->ti_sci->ops.dev_ops.get_device(kproc->ti_sci,
-						    kproc->ti_sci_id);
-	if (ret)
-		dev_err(dev, "module-reset deassert failed, cannot enable internal RAM loading (%pe)\n",
-			ERR_PTR(ret));
-
-	return ret;
-}
-
-/*
- * This function implements the .unprepare() ops and performs the complimentary
- * operations to that of the .prepare() ops. The function is used to assert the
- * global reset on applicable C66x cores. This completes the second portion of
- * powering down the C66x DSP cores. The cores themselves are only halted in the
- * .stop() callback through the local reset, and the .unprepare() ops is invoked
- * by the remoteproc core after the remoteproc is stopped to balance the global
- * reset. This callback is invoked only in remoteproc mode.
- */
-static int k3_dsp_rproc_unprepare(struct rproc *rproc)
-{
-	struct k3_dsp_rproc *kproc = rproc->priv;
-	struct device *dev = kproc->dev;
-	int ret;
-
-	ret = kproc->ti_sci->ops.dev_ops.put_device(kproc->ti_sci,
-						    kproc->ti_sci_id);
-	if (ret)
-		dev_err(dev, "module-reset assert failed (%pe)\n", ERR_PTR(ret));
-
-	return ret;
-}
-
-/*
- * Power up the DSP remote processor.
- *
- * This function will be invoked only after the firmware for this rproc
- * was loaded, parsed successfully, and all of its resource requirements
- * were met. This callback is invoked only in remoteproc mode.
- */
-static int k3_dsp_rproc_start(struct rproc *rproc)
-{
-	struct k3_dsp_rproc *kproc = rproc->priv;
-	struct device *dev = kproc->dev;
-	u32 boot_addr;
-	int ret;
-
-	ret = k3_dsp_rproc_request_mbox(rproc);
-	if (ret)
-		return ret;
-
-	boot_addr = rproc->bootaddr;
-	if (boot_addr & (kproc->data->boot_align_addr - 1)) {
-		dev_err(dev, "invalid boot address 0x%x, must be aligned on a 0x%x boundary\n",
-			boot_addr, kproc->data->boot_align_addr);
-		ret = -EINVAL;
-		goto put_mbox;
-	}
-
-	dev_err(dev, "booting DSP core using boot addr = 0x%x\n", boot_addr);
-	ret = ti_sci_proc_set_config(kproc->tsp, boot_addr, 0, 0);
-	if (ret)
-		goto put_mbox;
-
-	ret = k3_dsp_rproc_release(kproc);
-	if (ret)
-		goto put_mbox;
-
-	return 0;
-
-put_mbox:
-	mbox_free_channel(kproc->mbox);
-	return ret;
-}
-
-/*
- * Stop the DSP remote processor.
- *
- * This function puts the DSP processor into reset, and finishes processing
- * of any pending messages. This callback is invoked only in remoteproc mode.
- */
-static int k3_dsp_rproc_stop(struct rproc *rproc)
-{
-	struct k3_dsp_rproc *kproc = rproc->priv;
-
-	mbox_free_channel(kproc->mbox);
-
-	k3_dsp_rproc_reset(kproc);
-
-	return 0;
-}
-
-/*
- * Attach to a running DSP remote processor (IPC-only mode)
- *
- * This rproc attach callback only needs to request the mailbox, the remote
- * processor is already booted, so there is no need to issue any TI-SCI
- * commands to boot the DSP core. This callback is invoked only in IPC-only
- * mode.
- */
-static int k3_dsp_rproc_attach(struct rproc *rproc)
-{
-	struct k3_dsp_rproc *kproc = rproc->priv;
-	struct device *dev = kproc->dev;
-	int ret;
-
-	ret = k3_dsp_rproc_request_mbox(rproc);
-	if (ret)
-		return ret;
-
-	dev_info(dev, "DSP initialized in IPC-only mode\n");
-	return 0;
-}
-
-/*
- * Detach from a running DSP remote processor (IPC-only mode)
- *
- * This rproc detach callback performs the opposite operation to attach callback
- * and only needs to release the mailbox, the DSP core is not stopped and will
- * be left to continue to run its booted firmware. This callback is invoked only
- * in IPC-only mode.
- */
-static int k3_dsp_rproc_detach(struct rproc *rproc)
-{
-	struct k3_dsp_rproc *kproc = rproc->priv;
-	struct device *dev = kproc->dev;
-
-	mbox_free_channel(kproc->mbox);
-	dev_info(dev, "DSP deinitialized in IPC-only mode\n");
-	return 0;
-}
-
-/*
- * This function implements the .get_loaded_rsc_table() callback and is used
- * to provide the resource table for a booted DSP in IPC-only mode. The K3 DSP
- * firmwares follow a design-by-contract approach and are expected to have the
- * resource table at the base of the DDR region reserved for firmware usage.
- * This provides flexibility for the remote processor to be booted by different
- * bootloaders that may or may not have the ability to publish the resource table
- * address and size through a DT property. This callback is invoked only in
- * IPC-only mode.
- */
-static struct resource_table *k3_dsp_get_loaded_rsc_table(struct rproc *rproc,
-							  size_t *rsc_table_sz)
-{
-	struct k3_dsp_rproc *kproc = rproc->priv;
-	struct device *dev = kproc->dev;
-
-	if (!kproc->rmem[0].cpu_addr) {
-		dev_err(dev, "memory-region #1 does not exist, loaded rsc table can't be found");
-		return ERR_PTR(-ENOMEM);
-	}
-
-	/*
-	 * NOTE: The resource table size is currently hard-coded to a maximum
-	 * of 256 bytes. The most common resource table usage for K3 firmwares
-	 * is to only have the vdev resource entry and an optional trace entry.
-	 * The exact size could be computed based on resource table address, but
-	 * the hard-coded value suffices to support the IPC-only mode.
-	 */
-	*rsc_table_sz = 256;
-	return (struct resource_table *)kproc->rmem[0].cpu_addr;
-}
-
-/*
- * Custom function to translate a DSP device address (internal RAMs only) to a
- * kernel virtual address.  The DSPs can access their RAMs at either an internal
- * address visible only from a DSP, or at the SoC-level bus address. Both these
- * addresses need to be looked through for translation. The translated addresses
- * can be used either by the remoteproc core for loading (when using kernel
- * remoteproc loader), or by any rpmsg bus drivers.
- */
-static void *k3_dsp_rproc_da_to_va(struct rproc *rproc, u64 da, size_t len, bool *is_iomem)
-{
-	struct k3_dsp_rproc *kproc = rproc->priv;
-	void __iomem *va = NULL;
-	phys_addr_t bus_addr;
-	u32 dev_addr, offset;
-	size_t size;
-	int i;
-
-	if (len == 0)
-		return NULL;
-
-	for (i = 0; i < kproc->num_mems; i++) {
-		bus_addr = kproc->mem[i].bus_addr;
-		dev_addr = kproc->mem[i].dev_addr;
-		size = kproc->mem[i].size;
-
-		if (da < KEYSTONE_RPROC_LOCAL_ADDRESS_MASK) {
-			/* handle DSP-view addresses */
-			if (da >= dev_addr &&
-			    ((da + len) <= (dev_addr + size))) {
-				offset = da - dev_addr;
-				va = kproc->mem[i].cpu_addr + offset;
-				return (__force void *)va;
-			}
-		} else {
-			/* handle SoC-view addresses */
-			if (da >= bus_addr &&
-			    (da + len) <= (bus_addr + size)) {
-				offset = da - bus_addr;
-				va = kproc->mem[i].cpu_addr + offset;
-				return (__force void *)va;
-			}
-		}
-	}
-
-	/* handle static DDR reserved memory regions */
-	for (i = 0; i < kproc->num_rmems; i++) {
-		dev_addr = kproc->rmem[i].dev_addr;
-		size = kproc->rmem[i].size;
-
-		if (da >= dev_addr && ((da + len) <= (dev_addr + size))) {
-			offset = da - dev_addr;
-			va = kproc->rmem[i].cpu_addr + offset;
-			return (__force void *)va;
-		}
-	}
-
-	return NULL;
-}
-
-static const struct rproc_ops k3_dsp_rproc_ops = {
-	.start		= k3_dsp_rproc_start,
-	.stop		= k3_dsp_rproc_stop,
-	.kick		= k3_dsp_rproc_kick,
-	.da_to_va	= k3_dsp_rproc_da_to_va,
-};
-
-static int k3_dsp_rproc_of_get_memories(struct platform_device *pdev,
-					struct k3_dsp_rproc *kproc)
-{
-	const struct k3_dsp_dev_data *data = kproc->data;
-	struct device *dev = &pdev->dev;
-	struct resource *res;
-	int num_mems = 0;
-	int i;
-
-	num_mems = kproc->data->num_mems;
-	kproc->mem = devm_kcalloc(kproc->dev, num_mems,
-				  sizeof(*kproc->mem), GFP_KERNEL);
-	if (!kproc->mem)
-		return -ENOMEM;
-
-	for (i = 0; i < num_mems; i++) {
-		res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
-						   data->mems[i].name);
-		if (!res) {
-			dev_err(dev, "found no memory resource for %s\n",
-				data->mems[i].name);
-			return -EINVAL;
-		}
-		if (!devm_request_mem_region(dev, res->start,
-					     resource_size(res),
-					     dev_name(dev))) {
-			dev_err(dev, "could not request %s region for resource\n",
-				data->mems[i].name);
-			return -EBUSY;
-		}
-
-		kproc->mem[i].cpu_addr = devm_ioremap_wc(dev, res->start,
-							 resource_size(res));
-		if (!kproc->mem[i].cpu_addr) {
-			dev_err(dev, "failed to map %s memory\n",
-				data->mems[i].name);
-			return -ENOMEM;
-		}
-		kproc->mem[i].bus_addr = res->start;
-		kproc->mem[i].dev_addr = data->mems[i].dev_addr;
-		kproc->mem[i].size = resource_size(res);
-
-		dev_dbg(dev, "memory %8s: bus addr %pa size 0x%zx va %pK da 0x%x\n",
-			data->mems[i].name, &kproc->mem[i].bus_addr,
-			kproc->mem[i].size, kproc->mem[i].cpu_addr,
-			kproc->mem[i].dev_addr);
-	}
-	kproc->num_mems = num_mems;
-
-	return 0;
-}
-
-static int k3_dsp_reserved_mem_init(struct k3_dsp_rproc *kproc)
-{
-	struct device *dev = kproc->dev;
-	struct device_node *np = dev->of_node;
-	struct device_node *rmem_np;
-	struct reserved_mem *rmem;
-	int num_rmems;
-	int ret, i;
-
-	num_rmems = of_property_count_elems_of_size(np, "memory-region",
-						    sizeof(phandle));
-	if (num_rmems < 0) {
-		dev_err(dev, "device does not reserved memory regions (%pe)\n",
-			ERR_PTR(num_rmems));
-		return -EINVAL;
-	}
-	if (num_rmems < 2) {
-		dev_err(dev, "device needs at least two memory regions to be defined, num = %d\n",
-			num_rmems);
-		return -EINVAL;
-	}
-
-	/* use reserved memory region 0 for vring DMA allocations */
-	ret = of_reserved_mem_device_init_by_idx(dev, np, 0);
-	if (ret) {
-		dev_err(dev, "device cannot initialize DMA pool (%pe)\n",
-			ERR_PTR(ret));
-		return ret;
-	}
-
-	num_rmems--;
-	kproc->rmem = kcalloc(num_rmems, sizeof(*kproc->rmem), GFP_KERNEL);
-	if (!kproc->rmem) {
-		ret = -ENOMEM;
-		goto release_rmem;
-	}
-
-	/* use remaining reserved memory regions for static carveouts */
-	for (i = 0; i < num_rmems; i++) {
-		rmem_np = of_parse_phandle(np, "memory-region", i + 1);
-		if (!rmem_np) {
-			ret = -EINVAL;
-			goto unmap_rmem;
-		}
-
-		rmem = of_reserved_mem_lookup(rmem_np);
-		if (!rmem) {
-			of_node_put(rmem_np);
-			ret = -EINVAL;
-			goto unmap_rmem;
-		}
-		of_node_put(rmem_np);
-
-		kproc->rmem[i].bus_addr = rmem->base;
-		/* 64-bit address regions currently not supported */
-		kproc->rmem[i].dev_addr = (u32)rmem->base;
-		kproc->rmem[i].size = rmem->size;
-		kproc->rmem[i].cpu_addr = ioremap_wc(rmem->base, rmem->size);
-		if (!kproc->rmem[i].cpu_addr) {
-			dev_err(dev, "failed to map reserved memory#%d at %pa of size %pa\n",
-				i + 1, &rmem->base, &rmem->size);
-			ret = -ENOMEM;
-			goto unmap_rmem;
-		}
-
-		dev_dbg(dev, "reserved memory%d: bus addr %pa size 0x%zx va %pK da 0x%x\n",
-			i + 1, &kproc->rmem[i].bus_addr,
-			kproc->rmem[i].size, kproc->rmem[i].cpu_addr,
-			kproc->rmem[i].dev_addr);
-	}
-	kproc->num_rmems = num_rmems;
-
-	return 0;
-
-unmap_rmem:
-	for (i--; i >= 0; i--)
-		iounmap(kproc->rmem[i].cpu_addr);
-	kfree(kproc->rmem);
-release_rmem:
-	of_reserved_mem_device_release(kproc->dev);
-	return ret;
-}
-
-static void k3_dsp_reserved_mem_exit(struct k3_dsp_rproc *kproc)
-{
-	int i;
-
-	for (i = 0; i < kproc->num_rmems; i++)
-		iounmap(kproc->rmem[i].cpu_addr);
-	kfree(kproc->rmem);
-
-	of_reserved_mem_device_release(kproc->dev);
-}
-
-static
-struct ti_sci_proc *k3_dsp_rproc_of_get_tsp(struct device *dev,
-					    const struct ti_sci_handle *sci)
-{
-	struct ti_sci_proc *tsp;
-	u32 temp[2];
-	int ret;
-
-	ret = of_property_read_u32_array(dev->of_node, "ti,sci-proc-ids",
-					 temp, 2);
-	if (ret < 0)
-		return ERR_PTR(ret);
-
-	tsp = kzalloc(sizeof(*tsp), GFP_KERNEL);
-	if (!tsp)
-		return ERR_PTR(-ENOMEM);
-
-	tsp->dev = dev;
-	tsp->sci = sci;
-	tsp->ops = &sci->ops.proc_ops;
-	tsp->proc_id = temp[0];
-	tsp->host_id = temp[1];
-
-	return tsp;
-}
-
-static int k3_dsp_rproc_probe(struct platform_device *pdev)
-{
-	struct device *dev = &pdev->dev;
-	struct device_node *np = dev->of_node;
-	const struct k3_dsp_dev_data *data;
-	struct k3_dsp_rproc *kproc;
-	struct rproc *rproc;
-	const char *fw_name;
-	bool p_state = false;
-	int ret = 0;
-	int ret1;
-
-	data = of_device_get_match_data(dev);
-	if (!data)
-		return -ENODEV;
-
-	ret = rproc_of_parse_firmware(dev, 0, &fw_name);
-	if (ret)
-		return dev_err_probe(dev, ret, "failed to parse firmware-name property\n");
-
-	rproc = rproc_alloc(dev, dev_name(dev), &k3_dsp_rproc_ops, fw_name,
-			    sizeof(*kproc));
-	if (!rproc)
-		return -ENOMEM;
-
-	rproc->has_iommu = false;
-	rproc->recovery_disabled = true;
-	if (data->uses_lreset) {
-		rproc->ops->prepare = k3_dsp_rproc_prepare;
-		rproc->ops->unprepare = k3_dsp_rproc_unprepare;
-	}
-	kproc = rproc->priv;
-	kproc->rproc = rproc;
-	kproc->dev = dev;
-	kproc->data = data;
-
-	kproc->ti_sci = ti_sci_get_by_phandle(np, "ti,sci");
-	if (IS_ERR(kproc->ti_sci)) {
-		ret = dev_err_probe(dev, PTR_ERR(kproc->ti_sci),
-				    "failed to get ti-sci handle\n");
-		kproc->ti_sci = NULL;
-		goto free_rproc;
-	}
-
-	ret = of_property_read_u32(np, "ti,sci-dev-id", &kproc->ti_sci_id);
-	if (ret) {
-		dev_err_probe(dev, ret, "missing 'ti,sci-dev-id' property\n");
-		goto put_sci;
-	}
-
-	kproc->reset = devm_reset_control_get_exclusive(dev, NULL);
-	if (IS_ERR(kproc->reset)) {
-		ret = dev_err_probe(dev, PTR_ERR(kproc->reset),
-				    "failed to get reset\n");
-		goto put_sci;
-	}
-
-	kproc->tsp = k3_dsp_rproc_of_get_tsp(dev, kproc->ti_sci);
-	if (IS_ERR(kproc->tsp)) {
-		ret = dev_err_probe(dev, PTR_ERR(kproc->tsp),
-				    "failed to construct ti-sci proc control\n");
-		goto put_sci;
-	}
-
-	ret = ti_sci_proc_request(kproc->tsp);
-	if (ret < 0) {
-		dev_err_probe(dev, ret, "ti_sci_proc_request failed\n");
-		goto free_tsp;
-	}
-
-	ret = k3_dsp_rproc_of_get_memories(pdev, kproc);
-	if (ret)
-		goto release_tsp;
-
-	ret = k3_dsp_reserved_mem_init(kproc);
-	if (ret) {
-		dev_err_probe(dev, ret, "reserved memory init failed\n");
-		goto release_tsp;
-	}
-
-	ret = kproc->ti_sci->ops.dev_ops.is_on(kproc->ti_sci, kproc->ti_sci_id,
-					       NULL, &p_state);
-	if (ret) {
-		dev_err_probe(dev, ret, "failed to get initial state, mode cannot be determined\n");
-		goto release_mem;
-	}
-
-	/* configure J721E devices for either remoteproc or IPC-only mode */
-	if (p_state) {
-		dev_info(dev, "configured DSP for IPC-only mode\n");
-		rproc->state = RPROC_DETACHED;
-		/* override rproc ops with only required IPC-only mode ops */
-		rproc->ops->prepare = NULL;
-		rproc->ops->unprepare = NULL;
-		rproc->ops->start = NULL;
-		rproc->ops->stop = NULL;
-		rproc->ops->attach = k3_dsp_rproc_attach;
-		rproc->ops->detach = k3_dsp_rproc_detach;
-		rproc->ops->get_loaded_rsc_table = k3_dsp_get_loaded_rsc_table;
-	} else {
-		dev_info(dev, "configured DSP for remoteproc mode\n");
-		/*
-		 * ensure the DSP local reset is asserted to ensure the DSP
-		 * doesn't execute bogus code in .prepare() when the module
-		 * reset is released.
-		 */
-		if (data->uses_lreset) {
-			ret = reset_control_status(kproc->reset);
-			if (ret < 0) {
-				dev_err_probe(dev, ret, "failed to get reset status\n");
-				goto release_mem;
-			} else if (ret == 0) {
-				dev_warn(dev, "local reset is deasserted for device\n");
-				k3_dsp_rproc_reset(kproc);
-			}
-		}
-	}
-
-	ret = rproc_add(rproc);
-	if (ret) {
-		dev_err_probe(dev, ret, "failed to add register device with remoteproc core\n");
-		goto release_mem;
-	}
-
-	platform_set_drvdata(pdev, kproc);
-
-	return 0;
-
-release_mem:
-	k3_dsp_reserved_mem_exit(kproc);
-release_tsp:
-	ret1 = ti_sci_proc_release(kproc->tsp);
-	if (ret1)
-		dev_err(dev, "failed to release proc (%pe)\n", ERR_PTR(ret1));
-free_tsp:
-	kfree(kproc->tsp);
-put_sci:
-	ret1 = ti_sci_put_handle(kproc->ti_sci);
-	if (ret1)
-		dev_err(dev, "failed to put ti_sci handle (%pe)\n", ERR_PTR(ret1));
-free_rproc:
-	rproc_free(rproc);
-	return ret;
-}
-
-static void k3_dsp_rproc_remove(struct platform_device *pdev)
-{
-	struct k3_dsp_rproc *kproc = platform_get_drvdata(pdev);
-	struct rproc *rproc = kproc->rproc;
-	struct device *dev = &pdev->dev;
-	int ret;
-
-	if (rproc->state == RPROC_ATTACHED) {
-		ret = rproc_detach(rproc);
-		if (ret) {
-			/* Note this error path leaks resources */
-			dev_err(dev, "failed to detach proc (%pe)\n", ERR_PTR(ret));
-			return;
-		}
-	}
-
-	rproc_del(kproc->rproc);
-
-	ret = ti_sci_proc_release(kproc->tsp);
-	if (ret)
-		dev_err(dev, "failed to release proc (%pe)\n", ERR_PTR(ret));
-
-	kfree(kproc->tsp);
-
-	ret = ti_sci_put_handle(kproc->ti_sci);
-	if (ret)
-		dev_err(dev, "failed to put ti_sci handle (%pe)\n", ERR_PTR(ret));
-
-	k3_dsp_reserved_mem_exit(kproc);
-	rproc_free(kproc->rproc);
-}
-
-static const struct k3_dsp_mem_data c66_mems[] = {
-	{ .name = "l2sram", .dev_addr = 0x800000 },
-	{ .name = "l1pram", .dev_addr = 0xe00000 },
-	{ .name = "l1dram", .dev_addr = 0xf00000 },
-};
-
-/* C71x cores only have a L1P Cache, there are no L1P SRAMs */
-static const struct k3_dsp_mem_data c71_mems[] = {
-	{ .name = "l2sram", .dev_addr = 0x800000 },
-	{ .name = "l1dram", .dev_addr = 0xe00000 },
-};
-
-static const struct k3_dsp_mem_data c7xv_mems[] = {
-	{ .name = "l2sram", .dev_addr = 0x800000 },
-};
-
-static const struct k3_dsp_dev_data c66_data = {
-	.mems = c66_mems,
-	.num_mems = ARRAY_SIZE(c66_mems),
-	.boot_align_addr = SZ_1K,
-	.uses_lreset = true,
-};
-
-static const struct k3_dsp_dev_data c71_data = {
-	.mems = c71_mems,
-	.num_mems = ARRAY_SIZE(c71_mems),
-	.boot_align_addr = SZ_2M,
-	.uses_lreset = false,
-};
-
-static const struct k3_dsp_dev_data c7xv_data = {
-	.mems = c7xv_mems,
-	.num_mems = ARRAY_SIZE(c7xv_mems),
-	.boot_align_addr = SZ_2M,
-	.uses_lreset = false,
-};
-
-static const struct of_device_id k3_dsp_of_match[] = {
-	{ .compatible = "ti,j721e-c66-dsp", .data = &c66_data, },
-	{ .compatible = "ti,j721e-c71-dsp", .data = &c71_data, },
-	{ .compatible = "ti,j721s2-c71-dsp", .data = &c71_data, },
-	{ .compatible = "ti,am62a-c7xv-dsp", .data = &c7xv_data, },
-	{ /* sentinel */ },
-};
-MODULE_DEVICE_TABLE(of, k3_dsp_of_match);
-
-static struct platform_driver k3_dsp_rproc_driver = {
-	.probe	= k3_dsp_rproc_probe,
-	.remove_new = k3_dsp_rproc_remove,
-	.driver	= {
-		.name = "k3-dsp-rproc",
-		.of_match_table = k3_dsp_of_match,
-	},
-};
-
-module_platform_driver(k3_dsp_rproc_driver);
-
-MODULE_AUTHOR("Suman Anna <s-anna@ti.com>");
-MODULE_LICENSE("GPL v2");
-MODULE_DESCRIPTION("TI K3 DSP Remoteproc driver");
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * TI K3 DSP Remote Processor(s) driver
+ *
+ * Copyright (C) 2018-2022 Texas Instruments Incorporated - https://www.ti.com/
+ *	Suman Anna <s-anna@ti.com>
+ */
+
+#include <linux/io.h>
+#include <linux/mailbox_client.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_reserved_mem.h>
+#include <linux/omap-mailbox.h>
+#include <linux/platform_device.h>
+#include <linux/remoteproc.h>
+#include <linux/reset.h>
+#include <linux/slab.h>
+
+#include "omap_remoteproc.h"
+#include "remoteproc_internal.h"
+#include "ti_sci_proc.h"
+#include "ti_k3_common.h"
+
+/*
+ * Power up the DSP remote processor.
+ *
+ * This function will be invoked only after the firmware for this rproc
+ * was loaded, parsed successfully, and all of its resource requirements
+ * were met. This callback is invoked only in remoteproc mode.
+ */
+static int k3_dsp_rproc_start(struct rproc *rproc)
+{
+	struct k3_rproc *kproc = rproc->priv;
+	struct device *dev = kproc->dev;
+	u32 boot_addr;
+	int ret;
+
+	ret = k3_rproc_request_mbox(rproc);
+	if (ret)
+		return ret;
+
+	boot_addr = rproc->bootaddr;
+	if (boot_addr & (kproc->data->boot_align_addr - 1)) {
+		dev_err(dev, "invalid boot address 0x%x, must be aligned on a 0x%x boundary\n",
+			boot_addr, kproc->data->boot_align_addr);
+		ret = -EINVAL;
+		goto put_mbox;
+	}
+
+	dev_err(dev, "booting DSP core using boot addr = 0x%x\n", boot_addr);
+	ret = ti_sci_proc_set_config(kproc->tsp, boot_addr, 0, 0);
+	if (ret)
+		goto put_mbox;
+
+	ret = k3_rproc_release(kproc);
+	if (ret)
+		goto put_mbox;
+
+	return 0;
+
+put_mbox:
+	mbox_free_channel(kproc->mbox);
+	return ret;
+}
+
+/*
+ * Stop the DSP remote processor.
+ *
+ * This function puts the DSP processor into reset, and finishes processing
+ * of any pending messages. This callback is invoked only in remoteproc mode.
+ */
+static int k3_dsp_rproc_stop(struct rproc *rproc)
+{
+	struct k3_rproc *kproc = rproc->priv;
+
+	mbox_free_channel(kproc->mbox);
+
+	k3_rproc_reset(kproc);
+
+	return 0;
+}
+
+/*
+ * Attach to a running DSP remote processor (IPC-only mode)
+ *
+ * This rproc attach callback only needs to request the mailbox, the remote
+ * processor is already booted, so there is no need to issue any TI-SCI
+ * commands to boot the DSP core. This callback is invoked only in IPC-only
+ * mode.
+ */
+static int k3_dsp_rproc_attach(struct rproc *rproc)
+{
+	struct k3_rproc *kproc = rproc->priv;
+	struct device *dev = kproc->dev;
+	int ret;
+
+	ret = k3_rproc_request_mbox(rproc);
+	if (ret)
+		return ret;
+
+	dev_info(dev, "DSP initialized in IPC-only mode\n");
+	return 0;
+}
+
+/*
+ * Detach from a running DSP remote processor (IPC-only mode)
+ *
+ * This rproc detach callback performs the opposite operation to attach callback
+ * and only needs to release the mailbox, the DSP core is not stopped and will
+ * be left to continue to run its booted firmware. This callback is invoked only
+ * in IPC-only mode.
+ */
+static int k3_dsp_rproc_detach(struct rproc *rproc)
+{
+	struct k3_rproc *kproc = rproc->priv;
+	struct device *dev = kproc->dev;
+
+	mbox_free_channel(kproc->mbox);
+	dev_info(dev, "DSP deinitialized in IPC-only mode\n");
+	return 0;
+}
+
+
+static const struct rproc_ops k3_dsp_rproc_ops = {
+	.start		= k3_dsp_rproc_start,
+	.stop		= k3_dsp_rproc_stop,
+	.kick		= k3_rproc_kick,
+	.da_to_va	= k3_rproc_da_to_va,
+};
+
+static int k3_dsp_rproc_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	const struct k3_rproc_dev_data *data;
+	struct k3_rproc *kproc;
+	struct rproc *rproc;
+	const char *fw_name;
+	bool p_state = false;
+	int ret = 0;
+	int ret1;
+
+	data = of_device_get_match_data(dev);
+	if (!data)
+		return -ENODEV;
+
+	ret = rproc_of_parse_firmware(dev, 0, &fw_name);
+	if (ret)
+		return dev_err_probe(dev, ret, "failed to parse firmware-name property\n");
+
+	rproc = rproc_alloc(dev, dev_name(dev), &k3_dsp_rproc_ops, fw_name,
+			    sizeof(*kproc));
+	if (!rproc)
+		return -ENOMEM;
+
+	rproc->has_iommu = false;
+	rproc->recovery_disabled = true;
+	if (data->uses_lreset) {
+		rproc->ops->prepare = k3_rproc_prepare;
+		rproc->ops->unprepare = k3_rproc_unprepare;
+	}
+	kproc = rproc->priv;
+	kproc->rproc = rproc;
+	kproc->dev = dev;
+	kproc->data = data;
+
+	kproc->ti_sci = ti_sci_get_by_phandle(np, "ti,sci");
+	if (IS_ERR(kproc->ti_sci)) {
+		ret = dev_err_probe(dev, PTR_ERR(kproc->ti_sci),
+				    "failed to get ti-sci handle\n");
+		kproc->ti_sci = NULL;
+		goto free_rproc;
+	}
+
+	ret = of_property_read_u32(np, "ti,sci-dev-id", &kproc->ti_sci_id);
+	if (ret) {
+		dev_err_probe(dev, ret, "missing 'ti,sci-dev-id' property\n");
+		goto put_sci;
+	}
+
+	kproc->reset = devm_reset_control_get_exclusive(dev, NULL);
+	if (IS_ERR(kproc->reset)) {
+		ret = dev_err_probe(dev, PTR_ERR(kproc->reset),
+				    "failed to get reset\n");
+		goto put_sci;
+	}
+
+	kproc->tsp = k3_rproc_of_get_tsp(dev, kproc->ti_sci);
+	if (IS_ERR(kproc->tsp)) {
+		ret = dev_err_probe(dev, PTR_ERR(kproc->tsp),
+				    "failed to construct ti-sci proc control\n");
+		goto put_sci;
+	}
+
+	ret = ti_sci_proc_request(kproc->tsp);
+	if (ret < 0) {
+		dev_err_probe(dev, ret, "ti_sci_proc_request failed\n");
+		goto free_tsp;
+	}
+
+	ret = k3_rproc_of_get_memories(pdev, kproc);
+	if (ret)
+		goto release_tsp;
+
+	ret = k3_reserved_mem_init(kproc);
+	if (ret) {
+		dev_err_probe(dev, ret, "reserved memory init failed\n");
+		goto release_tsp;
+	}
+
+	ret = kproc->ti_sci->ops.dev_ops.is_on(kproc->ti_sci, kproc->ti_sci_id,
+					       NULL, &p_state);
+	if (ret) {
+		dev_err_probe(dev, ret, "failed to get initial state, mode cannot be determined\n");
+		goto release_mem;
+	}
+
+	/* configure J721E devices for either remoteproc or IPC-only mode */
+	if (p_state) {
+		dev_info(dev, "configured DSP for IPC-only mode\n");
+		rproc->state = RPROC_DETACHED;
+		/* override rproc ops with only required IPC-only mode ops */
+		rproc->ops->prepare = NULL;
+		rproc->ops->unprepare = NULL;
+		rproc->ops->start = NULL;
+		rproc->ops->stop = NULL;
+		rproc->ops->attach = k3_dsp_rproc_attach;
+		rproc->ops->detach = k3_dsp_rproc_detach;
+		rproc->ops->get_loaded_rsc_table = k3_get_loaded_rsc_table;
+	} else {
+		dev_info(dev, "configured DSP for remoteproc mode\n");
+		/*
+		 * ensure the DSP local reset is asserted to ensure the DSP
+		 * doesn't execute bogus code in .prepare() when the module
+		 * reset is released.
+		 */
+		if (data->uses_lreset) {
+			ret = reset_control_status(kproc->reset);
+			if (ret < 0) {
+				dev_err_probe(dev, ret, "failed to get reset status\n");
+				goto release_mem;
+			} else if (ret == 0) {
+				dev_warn(dev, "local reset is deasserted for device\n");
+				k3_rproc_reset(kproc);
+			}
+		}
+	}
+
+	ret = rproc_add(rproc);
+	if (ret) {
+		dev_err_probe(dev, ret, "failed to add register device with remoteproc core\n");
+		goto release_mem;
+	}
+
+	platform_set_drvdata(pdev, kproc);
+
+	return 0;
+
+release_mem:
+	k3_reserved_mem_exit(kproc);
+release_tsp:
+	ret1 = ti_sci_proc_release(kproc->tsp);
+	if (ret1)
+		dev_err(dev, "failed to release proc (%pe)\n", ERR_PTR(ret1));
+free_tsp:
+	kfree(kproc->tsp);
+put_sci:
+	ret1 = ti_sci_put_handle(kproc->ti_sci);
+	if (ret1)
+		dev_err(dev, "failed to put ti_sci handle (%pe)\n", ERR_PTR(ret1));
+free_rproc:
+	rproc_free(rproc);
+	return ret;
+}
+
+static void k3_dsp_rproc_remove(struct platform_device *pdev)
+{
+	struct k3_rproc *kproc = platform_get_drvdata(pdev);
+	struct rproc *rproc = kproc->rproc;
+	struct device *dev = &pdev->dev;
+	int ret;
+
+	if (rproc->state == RPROC_ATTACHED) {
+		ret = rproc_detach(rproc);
+		if (ret) {
+			/* Note this error path leaks resources */
+			dev_err(dev, "failed to detach proc (%pe)\n", ERR_PTR(ret));
+			return;
+		}
+	}
+
+	rproc_del(kproc->rproc);
+
+	ret = ti_sci_proc_release(kproc->tsp);
+	if (ret)
+		dev_err(dev, "failed to release proc (%pe)\n", ERR_PTR(ret));
+
+	kfree(kproc->tsp);
+
+	ret = ti_sci_put_handle(kproc->ti_sci);
+	if (ret)
+		dev_err(dev, "failed to put ti_sci handle (%pe)\n", ERR_PTR(ret));
+
+	k3_reserved_mem_exit(kproc);
+	rproc_free(kproc->rproc);
+}
+
+static const struct k3_rproc_mem_data c66_mems[] = {
+	{ .name = "l2sram", .dev_addr = 0x800000 },
+	{ .name = "l1pram", .dev_addr = 0xe00000 },
+	{ .name = "l1dram", .dev_addr = 0xf00000 },
+};
+
+/* C71x cores only have a L1P Cache, there are no L1P SRAMs */
+static const struct k3_rproc_mem_data c71_mems[] = {
+	{ .name = "l2sram", .dev_addr = 0x800000 },
+	{ .name = "l1dram", .dev_addr = 0xe00000 },
+};
+
+static const struct k3_rproc_mem_data c7xv_mems[] = {
+	{ .name = "l2sram", .dev_addr = 0x800000 },
+};
+
+static const struct k3_rproc_dev_data c66_data = {
+	.mems = c66_mems,
+	.num_mems = ARRAY_SIZE(c66_mems),
+	.boot_align_addr = SZ_1K,
+	.uses_lreset = true,
+};
+
+static const struct k3_rproc_dev_data c71_data = {
+	.mems = c71_mems,
+	.num_mems = ARRAY_SIZE(c71_mems),
+	.boot_align_addr = SZ_2M,
+	.uses_lreset = false,
+};
+
+static const struct k3_rproc_dev_data c7xv_data = {
+	.mems = c7xv_mems,
+	.num_mems = ARRAY_SIZE(c7xv_mems),
+	.boot_align_addr = SZ_2M,
+	.uses_lreset = false,
+};
+
+static const struct of_device_id k3_dsp_of_match[] = {
+	{ .compatible = "ti,j721e-c66-dsp", .data = &c66_data, },
+	{ .compatible = "ti,j721e-c71-dsp", .data = &c71_data, },
+	{ .compatible = "ti,j721s2-c71-dsp", .data = &c71_data, },
+	{ .compatible = "ti,am62a-c7xv-dsp", .data = &c7xv_data, },
+	{ /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, k3_dsp_of_match);
+
+static struct platform_driver k3_dsp_rproc_driver = {
+	.probe	= k3_dsp_rproc_probe,
+	.remove_new = k3_dsp_rproc_remove,
+	.driver	= {
+		.name = "k3-dsp-rproc",
+		.of_match_table = k3_dsp_of_match,
+	},
+};
+
+module_platform_driver(k3_dsp_rproc_driver);
+
+MODULE_AUTHOR("Suman Anna <s-anna@ti.com>");
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("TI K3 DSP Remoteproc driver");
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v7 3/5] remoteproc: k3: Move out functions common with M4 driver

[Andrew Davis]

On 2/2/24 11:55 AM, Hari Nagalla wrote:
> From: Martyn Welch <martyn.welch@collabora.com>
> 
> In the next commit we will be adding the M4F driver which shares a lot of
> commonality with the DSP driver. Move this shared functionality out so
> that it can be used by both drivers.
> 
> Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
> Signed-off-by: Hari Nagalla <hnagalla@ti.com>
> ---
> Changes since v2:
>   - New patch (reordered refactored from v2)
> 
> Changes since v3:
>   - Removed "ipc_only" element from k3_rproc structure
>   - Refactored to bring 3 more common functions
> 
> Changes since v4:
>   - None
> 
> Changes since v5:
>   - Rearranged the functions order to match with the functions in
>     ti_k3_dsp_remoteproc.c to ease review.
> 
> Changes since v6:
>   - Generated patch with -M/-B/-C options
> 

You where asked to generate this patch "correctly" with these options,
not just use them all and hope for the best.. Now it looks like you
re-wrote all of ti_k3_dsp_remoteproc.c when you only factored out
a couple functions to a different file.

Build up the new ti_k3_common.c one function per patch if it helps.
And factor the functions out of ti_k3_r5 also as it seems many
of these are common to that driver too.

Andrew

> link to v6:
> https://lore.kernel.org/all/20230913111644.29889-4-hnagalla@ti.com/
> 
>   drivers/remoteproc/Makefile               |    2 +-
>   drivers/remoteproc/ti_k3_common.c         |  583 ++++++++++
>   drivers/remoteproc/ti_k3_dsp_remoteproc.c | 1277 ++++++---------------
>   3 files changed, 952 insertions(+), 910 deletions(-)
>   create mode 100644 drivers/remoteproc/ti_k3_common.c
>   rewrite drivers/remoteproc/ti_k3_dsp_remoteproc.c (67%)
> 
> diff --git a/drivers/remoteproc/Makefile b/drivers/remoteproc/Makefile
> index 91314a9b43ce..55c552e27a45 100644
> --- a/drivers/remoteproc/Makefile
> +++ b/drivers/remoteproc/Makefile
> @@ -36,6 +36,6 @@ obj-$(CONFIG_RCAR_REMOTEPROC)		+= rcar_rproc.o
>   obj-$(CONFIG_ST_REMOTEPROC)		+= st_remoteproc.o
>   obj-$(CONFIG_ST_SLIM_REMOTEPROC)	+= st_slim_rproc.o
>   obj-$(CONFIG_STM32_RPROC)		+= stm32_rproc.o
> -obj-$(CONFIG_TI_K3_DSP_REMOTEPROC)	+= ti_k3_dsp_remoteproc.o
> +obj-$(CONFIG_TI_K3_DSP_REMOTEPROC)	+= ti_k3_dsp_remoteproc.o ti_k3_common.o
>   obj-$(CONFIG_TI_K3_R5_REMOTEPROC)	+= ti_k3_r5_remoteproc.o
>   obj-$(CONFIG_XLNX_R5_REMOTEPROC)	+= xlnx_r5_remoteproc.o
> diff --git a/drivers/remoteproc/ti_k3_common.c b/drivers/remoteproc/ti_k3_common.c
> new file mode 100644
> index 000000000000..62c7c5dba78a
> --- /dev/null
> +++ b/drivers/remoteproc/ti_k3_common.c
> @@ -0,0 +1,583 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * TI K3 Remote Processor(s) driver common code
> + *
> + * Refactored from ti_k3_dsp_remoteproc.c.
> + *
> + * ti_k3_dsp_remoteproc.c:
> + * Copyright (C) 2018-2022 Texas Instruments Incorporated - https://www.ti.com/
> + *	Suman Anna <s-anna@ti.com>
> + */
> +
> +#include <linux/io.h>
> +#include <linux/mailbox_client.h>
> +#include <linux/module.h>
> +#include <linux/of_address.h>
> +#include <linux/of_device.h>
> +#include <linux/of_reserved_mem.h>
> +#include <linux/omap-mailbox.h>
> +#include <linux/platform_device.h>
> +#include <linux/remoteproc.h>
> +#include <linux/reset.h>
> +#include <linux/slab.h>
> +
> +#include "omap_remoteproc.h"
> +#include "remoteproc_internal.h"
> +#include "ti_sci_proc.h"
> +#include "ti_k3_common.h"
> +
> +/**
> + * k3_rproc_mbox_callback() - inbound mailbox message handler
> + * @client: mailbox client pointer used for requesting the mailbox channel
> + * @data: mailbox payload
> + *
> + * This handler is invoked by the K3 mailbox driver whenever a mailbox
> + * message is received. Usually, the mailbox payload simply contains
> + * the index of the virtqueue that is kicked by the remote processor,
> + * and we let remoteproc core handle it.
> + *
> + * In addition to virtqueue indices, we also have some out-of-band values
> + * that indicate different events. Those values are deliberately very
> + * large so they don't coincide with virtqueue indices.
> + */
> +static void k3_rproc_mbox_callback(struct mbox_client *client, void *data)
> +{
> +	struct k3_rproc *kproc = container_of(client, struct k3_rproc,
> +						  client);
> +	struct device *dev = kproc->rproc->dev.parent;
> +	const char *name = kproc->rproc->name;
> +	u32 msg = omap_mbox_message(data);
> +
> +	dev_dbg(dev, "mbox msg: 0x%x\n", msg);
> +
> +	switch (msg) {
> +	case RP_MBOX_CRASH:
> +		/*
> +		 * remoteproc detected an exception, but error recovery is not
> +		 * supported. So, just log this for now
> +		 */
> +		dev_err(dev, "K3 rproc %s crashed\n", name);
> +		break;
> +	case RP_MBOX_ECHO_REPLY:
> +		dev_info(dev, "received echo reply from %s\n", name);
> +		break;
> +	default:
> +		/* silently handle all other valid messages */
> +		if (msg >= RP_MBOX_READY && msg < RP_MBOX_END_MSG)
> +			return;
> +		if (msg > kproc->rproc->max_notifyid) {
> +			dev_dbg(dev, "dropping unknown message 0x%x", msg);
> +			return;
> +		}
> +		/* msg contains the index of the triggered vring */
> +		if (rproc_vq_interrupt(kproc->rproc, msg) == IRQ_NONE)
> +			dev_dbg(dev, "no message was found in vqid %d\n", msg);
> +	}
> +}
> +
> +/*
> + * Kick the remote processor to notify about pending unprocessed messages.
> + * The vqid usage is not used and is inconsequential, as the kick is performed
> + * through a simulated GPIO (a bit in an IPC interrupt-triggering register),
> + * the remote processor is expected to process both its Tx and Rx virtqueues.
> + */
> +void k3_rproc_kick(struct rproc *rproc, int vqid)
> +{
> +	struct k3_rproc *kproc = rproc->priv;
> +	struct device *dev = rproc->dev.parent;
> +	mbox_msg_t msg = (mbox_msg_t)vqid;
> +	int ret;
> +
> +	/* send the index of the triggered virtqueue in the mailbox payload */
> +	ret = mbox_send_message(kproc->mbox, (void *)msg);
> +	if (ret < 0)
> +		dev_err(dev, "failed to send mailbox message, status = %d\n",
> +			ret);
> +}
> +EXPORT_SYMBOL_GPL(k3_rproc_kick);
> +
> +/* Put the remote processor into reset */
> +int k3_rproc_reset(struct k3_rproc *kproc)
> +{
> +	struct device *dev = kproc->dev;
> +	int ret;
> +
> +	ret = reset_control_assert(kproc->reset);
> +	if (ret) {
> +		dev_err(dev, "local-reset assert failed, ret = %d\n", ret);
> +		return ret;
> +	}
> +
> +	if (kproc->data->uses_lreset)
> +		return ret;
> +
> +	ret = kproc->ti_sci->ops.dev_ops.put_device(kproc->ti_sci,
> +						    kproc->ti_sci_id);
> +	if (ret) {
> +		dev_err(dev, "module-reset assert failed, ret = %d\n", ret);
> +		if (reset_control_deassert(kproc->reset))
> +			dev_warn(dev, "local-reset deassert back failed\n");
> +	}
> +
> +	return ret;
> +}
> +EXPORT_SYMBOL_GPL(k3_rproc_reset);
> +
> +/* Release the remote processor from reset */
> +int k3_rproc_release(struct k3_rproc *kproc)
> +{
> +	struct device *dev = kproc->dev;
> +	int ret;
> +
> +	if (kproc->data->uses_lreset)
> +		goto lreset;
> +
> +	ret = kproc->ti_sci->ops.dev_ops.get_device(kproc->ti_sci,
> +						    kproc->ti_sci_id);
> +	if (ret) {
> +		dev_err(dev, "module-reset deassert failed, ret = %d\n", ret);
> +		return ret;
> +	}
> +
> +lreset:
> +	ret = reset_control_deassert(kproc->reset);
> +	if (ret) {
> +		dev_err(dev, "local-reset deassert failed, ret = %d\n", ret);
> +		if (kproc->ti_sci->ops.dev_ops.put_device(kproc->ti_sci,
> +							  kproc->ti_sci_id))
> +			dev_warn(dev, "module-reset assert back failed\n");
> +	}
> +
> +	return ret;
> +}
> +EXPORT_SYMBOL_GPL(k3_rproc_release);
> +
> +int k3_rproc_request_mbox(struct rproc *rproc)
> +{
> +	struct k3_rproc *kproc = rproc->priv;
> +	struct mbox_client *client = &kproc->client;
> +	struct device *dev = kproc->dev;
> +	int ret;
> +
> +	client->dev = dev;
> +	client->tx_done = NULL;
> +	client->rx_callback = k3_rproc_mbox_callback;
> +	client->tx_block = false;
> +	client->knows_txdone = false;
> +
> +	kproc->mbox = mbox_request_channel(client, 0);
> +	if (IS_ERR(kproc->mbox)) {
> +		ret = -EBUSY;
> +		dev_err(dev, "mbox_request_channel failed: %ld\n",
> +			PTR_ERR(kproc->mbox));
> +		return ret;
> +	}
> +
> +	/*
> +	 * Ping the remote processor, this is only for sanity-sake for now;
> +	 * there is no functional effect whatsoever.
> +	 *
> +	 * Note that the reply will _not_ arrive immediately: this message
> +	 * will wait in the mailbox fifo until the remote processor is booted.
> +	 */
> +	ret = mbox_send_message(kproc->mbox, (void *)RP_MBOX_ECHO_REQUEST);
> +	if (ret < 0) {
> +		dev_err(dev, "mbox_send_message failed: %d\n", ret);
> +		mbox_free_channel(kproc->mbox);
> +		return ret;
> +	}
> +
> +	return 0;
> +}
> +EXPORT_SYMBOL_GPL(k3_rproc_request_mbox);
> +
> +/*
> + * The DSP and MCU cores have a local reset that affects only the CPU, and a
> + * generic module reset that powers on the device and allows the internal
> + * memories to be accessed while the local reset is asserted. This function is
> + * used to release the global reset on remote cores to allow loading into the
> + * internal RAMs. The .prepare() ops is invoked by remoteproc core before any
> + * firmware loading, and is followed by the .start() ops after loading to
> + * actually let the remote cores to run. This callback is invoked only in
> + * remoteproc mode.
> + */
> +int k3_rproc_prepare(struct rproc *rproc)
> +{
> +	struct k3_rproc *kproc = rproc->priv;
> +	struct device *dev = kproc->dev;
> +	int ret;
> +
> +	ret = kproc->ti_sci->ops.dev_ops.get_device(kproc->ti_sci,
> +						    kproc->ti_sci_id);
> +	if (ret)
> +		dev_err(dev, "module-reset deassert failed, cannot enable internal RAM loading, ret = %d\n",
> +			ret);
> +
> +	return ret;
> +}
> +EXPORT_SYMBOL_GPL(k3_rproc_prepare);
> +
> +/*
> + * This function implements the .unprepare() ops and performs the complimentary
> + * operations to that of the .prepare() ops. The function is used to assert the
> + * global reset on applicable DSP, MCU cores. This completes the second portion of
> + * powering down the remote core. The cores themselves are only halted in the
> + * .stop() callback through the local reset, and the .unprepare() ops is invoked
> + * by the remoteproc core after the remoteproc is stopped to balance the global
> + * reset. This callback is invoked only in remoteproc mode.
> + */
> +int k3_rproc_unprepare(struct rproc *rproc)
> +{
> +	struct k3_rproc *kproc = rproc->priv;
> +	struct device *dev = kproc->dev;
> +	int ret;
> +
> +	ret = kproc->ti_sci->ops.dev_ops.put_device(kproc->ti_sci,
> +						    kproc->ti_sci_id);
> +	if (ret)
> +		dev_err(dev, "module-reset assert failed, ret = %d\n", ret);
> +
> +	return ret;
> +}
> +EXPORT_SYMBOL_GPL(k3_rproc_unprepare);
> +
> +/*
> + * This function implements the .get_loaded_rsc_table() callback and is used
> + * to provide the resource table for a booted remote processor in IPC-only
> + * mode. The remote processor firmwares follow a design-by-contract approach
> + * and are expected to have the resource table at the base of the DDR region
> + * reserved for firmware usage. This provides flexibility for the remote
> + * processor to be booted by different bootloaders that may or may not have the
> + * ability to publish the resource table address and size through a DT
> + * property.
> + */
> +struct resource_table *k3_get_loaded_rsc_table(struct rproc *rproc,
> +					       size_t *rsc_table_sz)
> +{
> +	struct k3_rproc *kproc = rproc->priv;
> +	struct device *dev = kproc->dev;
> +
> +	if (!kproc->rmem[0].cpu_addr) {
> +		dev_err(dev, "memory-region #1 does not exist, loaded rsc table can't be found");
> +		return ERR_PTR(-ENOMEM);
> +	}
> +
> +	/*
> +	 * NOTE: The resource table size is currently hard-coded to a maximum
> +	 * of 256 bytes. The most common resource table usage for K3 firmwares
> +	 * is to only have the vdev resource entry and an optional trace entry.
> +	 * The exact size could be computed based on resource table address, but
> +	 * the hard-coded value suffices to support the IPC-only mode.
> +	 */
> +	*rsc_table_sz = 256;
> +	return (struct resource_table *)kproc->rmem[0].cpu_addr;
> +}
> +EXPORT_SYMBOL_GPL(k3_get_loaded_rsc_table);
> +
> +/*
> + * Custom function to translate a remote processor device address (internal
> + * RAMs only) to a kernel virtual address.  The remote processors can access
> + * their RAMs at either an internal address visible only from a remote
> + * processor, or at the SoC-level bus address. Both these addresses need to be
> + * looked through for translation. The translated addresses can be used either
> + * by the remoteproc core for loading (when using kernel remoteproc loader), or
> + * by any rpmsg bus drivers.
> + */
> +void *k3_rproc_da_to_va(struct rproc *rproc, u64 da, size_t len, bool *is_iomem)
> +{
> +	struct k3_rproc *kproc = rproc->priv;
> +	void __iomem *va = NULL;
> +	phys_addr_t bus_addr;
> +	u32 dev_addr, offset;
> +	size_t size;
> +	int i;
> +
> +	if (len == 0)
> +		return NULL;
> +
> +	for (i = 0; i < kproc->num_mems; i++) {
> +		bus_addr = kproc->mem[i].bus_addr;
> +		dev_addr = kproc->mem[i].dev_addr;
> +		size = kproc->mem[i].size;
> +
> +		if (da < KEYSTONE_RPROC_LOCAL_ADDRESS_MASK) {
> +			/* handle remote-view addresses */
> +			if (da >= dev_addr &&
> +			    ((da + len) <= (dev_addr + size))) {
> +				offset = da - dev_addr;
> +				va = kproc->mem[i].cpu_addr + offset;
> +				return (__force void *)va;
> +			}
> +		} else {
> +			/* handle SoC-view addresses */
> +			if (da >= bus_addr &&
> +			    (da + len) <= (bus_addr + size)) {
> +				offset = da - bus_addr;
> +				va = kproc->mem[i].cpu_addr + offset;
> +				return (__force void *)va;
> +			}
> +		}
> +	}
> +
> +	/* handle any SRAM regions using SoC-view addresses */
> +	for (i = 0; i < kproc->num_sram; i++) {
> +		dev_addr = kproc->sram[i].dev_addr;
> +		size = kproc->sram[i].size;
> +
> +		if (da >= dev_addr && ((da + len) <= (dev_addr + size))) {
> +			offset = da - dev_addr;
> +			va = kproc->sram[i].cpu_addr + offset;
> +			return (__force void *)va;
> +		}
> +	}
> +
> +	/* handle static DDR reserved memory regions */
> +	for (i = 0; i < kproc->num_rmems; i++) {
> +		dev_addr = kproc->rmem[i].dev_addr;
> +		size = kproc->rmem[i].size;
> +
> +		if (da >= dev_addr && ((da + len) <= (dev_addr + size))) {
> +			offset = da - dev_addr;
> +			va = kproc->rmem[i].cpu_addr + offset;
> +			return (__force void *)va;
> +		}
> +	}
> +
> +	return NULL;
> +}
> +EXPORT_SYMBOL_GPL(k3_rproc_da_to_va);
> +
> +int k3_rproc_of_get_memories(struct platform_device *pdev,
> +			     struct k3_rproc *kproc)
> +{
> +	const struct k3_rproc_dev_data *data = kproc->data;
> +	struct device *dev = &pdev->dev;
> +	struct resource *res;
> +	int num_mems = 0;
> +	int i;
> +
> +	num_mems = kproc->data->num_mems;
> +	kproc->mem = devm_kcalloc(kproc->dev, num_mems,
> +				  sizeof(*kproc->mem), GFP_KERNEL);
> +	if (!kproc->mem)
> +		return -ENOMEM;
> +
> +	for (i = 0; i < num_mems; i++) {
> +		res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
> +						   data->mems[i].name);
> +		if (!res) {
> +			dev_err(dev, "found no memory resource for %s\n",
> +				data->mems[i].name);
> +			return -EINVAL;
> +		}
> +		if (!devm_request_mem_region(dev, res->start,
> +					     resource_size(res),
> +					     dev_name(dev))) {
> +			dev_err(dev, "could not request %s region for resource\n",
> +				data->mems[i].name);
> +			return -EBUSY;
> +		}
> +
> +		kproc->mem[i].cpu_addr = devm_ioremap_wc(dev, res->start,
> +							 resource_size(res));
> +		if (!kproc->mem[i].cpu_addr) {
> +			dev_err(dev, "failed to map %s memory\n",
> +				data->mems[i].name);
> +			return -ENOMEM;
> +		}
> +		kproc->mem[i].bus_addr = res->start;
> +		kproc->mem[i].dev_addr = data->mems[i].dev_addr;
> +		kproc->mem[i].size = resource_size(res);
> +
> +		dev_dbg(dev, "memory %8s: bus addr %pa size 0x%zx va %pK da 0x%x\n",
> +			data->mems[i].name, &kproc->mem[i].bus_addr,
> +			kproc->mem[i].size, kproc->mem[i].cpu_addr,
> +			kproc->mem[i].dev_addr);
> +	}
> +	kproc->num_mems = num_mems;
> +
> +	return 0;
> +}
> +EXPORT_SYMBOL_GPL(k3_rproc_of_get_memories);
> +
> +int k3_rproc_of_get_sram_memories(struct platform_device *pdev,
> +					   struct k3_rproc *kproc)
> +{
> +	struct device_node *np = pdev->dev.of_node;
> +	struct device *dev = &pdev->dev;
> +	struct device_node *sram_np;
> +	struct resource res;
> +	int num_sram;
> +	int i, ret;
> +
> +	num_sram = of_property_count_elems_of_size(np, "sram", sizeof(phandle));
> +	if (num_sram <= 0) {
> +		dev_dbg(dev, "device does not use reserved on-chip memories, num_sram = %d\n",
> +			num_sram);
> +		return 0;
> +	}
> +
> +	kproc->sram = devm_kcalloc(dev, num_sram, sizeof(*kproc->sram), GFP_KERNEL);
> +	if (!kproc->sram)
> +		return -ENOMEM;
> +
> +	for (i = 0; i < num_sram; i++) {
> +		sram_np = of_parse_phandle(np, "sram", i);
> +		if (!sram_np)
> +			return -EINVAL;
> +
> +		if (!of_device_is_available(sram_np)) {
> +			of_node_put(sram_np);
> +			return -EINVAL;
> +		}
> +
> +		ret = of_address_to_resource(sram_np, 0, &res);
> +		of_node_put(sram_np);
> +		if (ret)
> +			return -EINVAL;
> +
> +		kproc->sram[i].bus_addr = res.start;
> +		kproc->sram[i].dev_addr = res.start;
> +		kproc->sram[i].size = resource_size(&res);
> +		kproc->sram[i].cpu_addr = devm_ioremap_wc(dev, res.start,
> +							 resource_size(&res));
> +		if (!kproc->sram[i].cpu_addr) {
> +			dev_err(dev, "failed to parse and map sram%d memory at %pad\n",
> +				i, &res.start);
> +			return -ENOMEM;
> +		}
> +
> +		dev_dbg(dev, "memory sram%d: bus addr %pa size 0x%zx va %pK da 0x%x\n",
> +			i, &kproc->sram[i].bus_addr,
> +			kproc->sram[i].size, kproc->sram[i].cpu_addr,
> +			kproc->sram[i].dev_addr);
> +	}
> +	kproc->num_sram = num_sram;
> +
> +	return 0;
> +}
> +EXPORT_SYMBOL_GPL(k3_rproc_of_get_sram_memories);
> +int k3_reserved_mem_init(struct k3_rproc *kproc)
> +{
> +	struct device *dev = kproc->dev;
> +	struct device_node *np = dev->of_node;
> +	struct device_node *rmem_np;
> +	struct reserved_mem *rmem;
> +	int num_rmems;
> +	int ret, i;
> +
> +	num_rmems = of_property_count_elems_of_size(np, "memory-region",
> +						    sizeof(phandle));
> +	if (num_rmems <= 0) {
> +		dev_err(dev, "device does not reserved memory regions, ret = %d\n",
> +			num_rmems);
> +		return -EINVAL;
> +	}
> +	if (num_rmems < 2) {
> +		dev_err(dev, "device needs at least two memory regions to be defined, num = %d\n",
> +			num_rmems);
> +		return -EINVAL;
> +	}
> +
> +	/* use reserved memory region 0 for vring DMA allocations */
> +	ret = of_reserved_mem_device_init_by_idx(dev, np, 0);
> +	if (ret) {
> +		dev_err(dev, "device cannot initialize DMA pool, ret = %d\n",
> +			ret);
> +		return ret;
> +	}
> +
> +	num_rmems--;
> +	kproc->rmem = kcalloc(num_rmems, sizeof(*kproc->rmem), GFP_KERNEL);
> +	if (!kproc->rmem) {
> +		ret = -ENOMEM;
> +		goto release_rmem;
> +	}
> +
> +	/* use remaining reserved memory regions for static carveouts */
> +	for (i = 0; i < num_rmems; i++) {
> +		rmem_np = of_parse_phandle(np, "memory-region", i + 1);
> +		if (!rmem_np) {
> +			ret = -EINVAL;
> +			goto unmap_rmem;
> +		}
> +
> +		rmem = of_reserved_mem_lookup(rmem_np);
> +		if (!rmem) {
> +			of_node_put(rmem_np);
> +			ret = -EINVAL;
> +			goto unmap_rmem;
> +		}
> +		of_node_put(rmem_np);
> +
> +		kproc->rmem[i].bus_addr = rmem->base;
> +		/* 64-bit address regions currently not supported */
> +		kproc->rmem[i].dev_addr = (u32)rmem->base;
> +		kproc->rmem[i].size = rmem->size;
> +		kproc->rmem[i].cpu_addr = ioremap_wc(rmem->base, rmem->size);
> +		if (!kproc->rmem[i].cpu_addr) {
> +			dev_err(dev, "failed to map reserved memory#%d at %pa of size %pa\n",
> +				i + 1, &rmem->base, &rmem->size);
> +			ret = -ENOMEM;
> +			goto unmap_rmem;
> +		}
> +
> +		dev_dbg(dev, "reserved memory%d: bus addr %pa size 0x%zx va %pK da 0x%x\n",
> +			i + 1, &kproc->rmem[i].bus_addr,
> +			kproc->rmem[i].size, kproc->rmem[i].cpu_addr,
> +			kproc->rmem[i].dev_addr);
> +	}
> +	kproc->num_rmems = num_rmems;
> +
> +	return 0;
> +
> +unmap_rmem:
> +	for (i--; i >= 0; i--)
> +		iounmap(kproc->rmem[i].cpu_addr);
> +	kfree(kproc->rmem);
> +release_rmem:
> +	of_reserved_mem_device_release(kproc->dev);
> +	return ret;
> +}
> +EXPORT_SYMBOL_GPL(k3_reserved_mem_init);
> +
> +void k3_reserved_mem_exit(struct k3_rproc *kproc)
> +{
> +	int i;
> +
> +	for (i = 0; i < kproc->num_rmems; i++)
> +		iounmap(kproc->rmem[i].cpu_addr);
> +	kfree(kproc->rmem);
> +
> +	of_reserved_mem_device_release(kproc->dev);
> +}
> +EXPORT_SYMBOL_GPL(k3_reserved_mem_exit);
> +
> +struct ti_sci_proc *k3_rproc_of_get_tsp(struct device *dev,
> +					const struct ti_sci_handle *sci)
> +{
> +	struct ti_sci_proc *tsp;
> +	u32 temp[2];
> +	int ret;
> +
> +	ret = of_property_read_u32_array(dev->of_node, "ti,sci-proc-ids",
> +					 temp, 2);
> +	if (ret < 0)
> +		return ERR_PTR(ret);
> +
> +	tsp = kzalloc(sizeof(*tsp), GFP_KERNEL);
> +	if (!tsp)
> +		return ERR_PTR(-ENOMEM);
> +
> +	tsp->dev = dev;
> +	tsp->sci = sci;
> +	tsp->ops = &sci->ops.proc_ops;
> +	tsp->proc_id = temp[0];
> +	tsp->host_id = temp[1];
> +
> +	return tsp;
> +}
> +EXPORT_SYMBOL_GPL(k3_rproc_of_get_tsp);
> +
> +MODULE_LICENSE("GPL v2");
> +MODULE_DESCRIPTION("TI K3 common Remoteproc support");
> diff --git a/drivers/remoteproc/ti_k3_dsp_remoteproc.c b/drivers/remoteproc/ti_k3_dsp_remoteproc.c
> dissimilarity index 67%
> index ab882e3b7130..ebe23fc5ca44 100644
> --- a/drivers/remoteproc/ti_k3_dsp_remoteproc.c
> +++ b/drivers/remoteproc/ti_k3_dsp_remoteproc.c
> @@ -1,909 +1,368 @@
> -// SPDX-License-Identifier: GPL-2.0-only
> -/*
> - * TI K3 DSP Remote Processor(s) driver
> - *
> - * Copyright (C) 2018-2022 Texas Instruments Incorporated - https://www.ti.com/
> - *	Suman Anna <s-anna@ti.com>
> - */
> -
> -#include <linux/io.h>
> -#include <linux/mailbox_client.h>
> -#include <linux/module.h>
> -#include <linux/of.h>
> -#include <linux/of_reserved_mem.h>
> -#include <linux/omap-mailbox.h>
> -#include <linux/platform_device.h>
> -#include <linux/remoteproc.h>
> -#include <linux/reset.h>
> -#include <linux/slab.h>
> -
> -#include "omap_remoteproc.h"
> -#include "remoteproc_internal.h"
> -#include "ti_sci_proc.h"
> -
> -#define KEYSTONE_RPROC_LOCAL_ADDRESS_MASK	(SZ_16M - 1)
> -
> -/**
> - * struct k3_dsp_mem - internal memory structure
> - * @cpu_addr: MPU virtual address of the memory region
> - * @bus_addr: Bus address used to access the memory region
> - * @dev_addr: Device address of the memory region from DSP view
> - * @size: Size of the memory region
> - */
> -struct k3_dsp_mem {
> -	void __iomem *cpu_addr;
> -	phys_addr_t bus_addr;
> -	u32 dev_addr;
> -	size_t size;
> -};
> -
> -/**
> - * struct k3_dsp_mem_data - memory definitions for a DSP
> - * @name: name for this memory entry
> - * @dev_addr: device address for the memory entry
> - */
> -struct k3_dsp_mem_data {
> -	const char *name;
> -	const u32 dev_addr;
> -};
> -
> -/**
> - * struct k3_dsp_dev_data - device data structure for a DSP
> - * @mems: pointer to memory definitions for a DSP
> - * @num_mems: number of memory regions in @mems
> - * @boot_align_addr: boot vector address alignment granularity
> - * @uses_lreset: flag to denote the need for local reset management
> - */
> -struct k3_dsp_dev_data {
> -	const struct k3_dsp_mem_data *mems;
> -	u32 num_mems;
> -	u32 boot_align_addr;
> -	bool uses_lreset;
> -};
> -
> -/**
> - * struct k3_dsp_rproc - k3 DSP remote processor driver structure
> - * @dev: cached device pointer
> - * @rproc: remoteproc device handle
> - * @mem: internal memory regions data
> - * @num_mems: number of internal memory regions
> - * @rmem: reserved memory regions data
> - * @num_rmems: number of reserved memory regions
> - * @reset: reset control handle
> - * @data: pointer to DSP-specific device data
> - * @tsp: TI-SCI processor control handle
> - * @ti_sci: TI-SCI handle
> - * @ti_sci_id: TI-SCI device identifier
> - * @mbox: mailbox channel handle
> - * @client: mailbox client to request the mailbox channel
> - */
> -struct k3_dsp_rproc {
> -	struct device *dev;
> -	struct rproc *rproc;
> -	struct k3_dsp_mem *mem;
> -	int num_mems;
> -	struct k3_dsp_mem *rmem;
> -	int num_rmems;
> -	struct reset_control *reset;
> -	const struct k3_dsp_dev_data *data;
> -	struct ti_sci_proc *tsp;
> -	const struct ti_sci_handle *ti_sci;
> -	u32 ti_sci_id;
> -	struct mbox_chan *mbox;
> -	struct mbox_client client;
> -};
> -
> -/**
> - * k3_dsp_rproc_mbox_callback() - inbound mailbox message handler
> - * @client: mailbox client pointer used for requesting the mailbox channel
> - * @data: mailbox payload
> - *
> - * This handler is invoked by the OMAP mailbox driver whenever a mailbox
> - * message is received. Usually, the mailbox payload simply contains
> - * the index of the virtqueue that is kicked by the remote processor,
> - * and we let remoteproc core handle it.
> - *
> - * In addition to virtqueue indices, we also have some out-of-band values
> - * that indicate different events. Those values are deliberately very
> - * large so they don't coincide with virtqueue indices.
> - */
> -static void k3_dsp_rproc_mbox_callback(struct mbox_client *client, void *data)
> -{
> -	struct k3_dsp_rproc *kproc = container_of(client, struct k3_dsp_rproc,
> -						  client);
> -	struct device *dev = kproc->rproc->dev.parent;
> -	const char *name = kproc->rproc->name;
> -	u32 msg = omap_mbox_message(data);
> -
> -	dev_dbg(dev, "mbox msg: 0x%x\n", msg);
> -
> -	switch (msg) {
> -	case RP_MBOX_CRASH:
> -		/*
> -		 * remoteproc detected an exception, but error recovery is not
> -		 * supported. So, just log this for now
> -		 */
> -		dev_err(dev, "K3 DSP rproc %s crashed\n", name);
> -		break;
> -	case RP_MBOX_ECHO_REPLY:
> -		dev_info(dev, "received echo reply from %s\n", name);
> -		break;
> -	default:
> -		/* silently handle all other valid messages */
> -		if (msg >= RP_MBOX_READY && msg < RP_MBOX_END_MSG)
> -			return;
> -		if (msg > kproc->rproc->max_notifyid) {
> -			dev_dbg(dev, "dropping unknown message 0x%x", msg);
> -			return;
> -		}
> -		/* msg contains the index of the triggered vring */
> -		if (rproc_vq_interrupt(kproc->rproc, msg) == IRQ_NONE)
> -			dev_dbg(dev, "no message was found in vqid %d\n", msg);
> -	}
> -}
> -
> -/*
> - * Kick the remote processor to notify about pending unprocessed messages.
> - * The vqid usage is not used and is inconsequential, as the kick is performed
> - * through a simulated GPIO (a bit in an IPC interrupt-triggering register),
> - * the remote processor is expected to process both its Tx and Rx virtqueues.
> - */
> -static void k3_dsp_rproc_kick(struct rproc *rproc, int vqid)
> -{
> -	struct k3_dsp_rproc *kproc = rproc->priv;
> -	struct device *dev = rproc->dev.parent;
> -	mbox_msg_t msg = (mbox_msg_t)vqid;
> -	int ret;
> -
> -	/* send the index of the triggered virtqueue in the mailbox payload */
> -	ret = mbox_send_message(kproc->mbox, (void *)msg);
> -	if (ret < 0)
> -		dev_err(dev, "failed to send mailbox message (%pe)\n",
> -			ERR_PTR(ret));
> -}
> -
> -/* Put the DSP processor into reset */
> -static int k3_dsp_rproc_reset(struct k3_dsp_rproc *kproc)
> -{
> -	struct device *dev = kproc->dev;
> -	int ret;
> -
> -	ret = reset_control_assert(kproc->reset);
> -	if (ret) {
> -		dev_err(dev, "local-reset assert failed (%pe)\n", ERR_PTR(ret));
> -		return ret;
> -	}
> -
> -	if (kproc->data->uses_lreset)
> -		return ret;
> -
> -	ret = kproc->ti_sci->ops.dev_ops.put_device(kproc->ti_sci,
> -						    kproc->ti_sci_id);
> -	if (ret) {
> -		dev_err(dev, "module-reset assert failed (%pe)\n", ERR_PTR(ret));
> -		if (reset_control_deassert(kproc->reset))
> -			dev_warn(dev, "local-reset deassert back failed\n");
> -	}
> -
> -	return ret;
> -}
> -
> -/* Release the DSP processor from reset */
> -static int k3_dsp_rproc_release(struct k3_dsp_rproc *kproc)
> -{
> -	struct device *dev = kproc->dev;
> -	int ret;
> -
> -	if (kproc->data->uses_lreset)
> -		goto lreset;
> -
> -	ret = kproc->ti_sci->ops.dev_ops.get_device(kproc->ti_sci,
> -						    kproc->ti_sci_id);
> -	if (ret) {
> -		dev_err(dev, "module-reset deassert failed (%pe)\n", ERR_PTR(ret));
> -		return ret;
> -	}
> -
> -lreset:
> -	ret = reset_control_deassert(kproc->reset);
> -	if (ret) {
> -		dev_err(dev, "local-reset deassert failed, (%pe)\n", ERR_PTR(ret));
> -		if (kproc->ti_sci->ops.dev_ops.put_device(kproc->ti_sci,
> -							  kproc->ti_sci_id))
> -			dev_warn(dev, "module-reset assert back failed\n");
> -	}
> -
> -	return ret;
> -}
> -
> -static int k3_dsp_rproc_request_mbox(struct rproc *rproc)
> -{
> -	struct k3_dsp_rproc *kproc = rproc->priv;
> -	struct mbox_client *client = &kproc->client;
> -	struct device *dev = kproc->dev;
> -	int ret;
> -
> -	client->dev = dev;
> -	client->tx_done = NULL;
> -	client->rx_callback = k3_dsp_rproc_mbox_callback;
> -	client->tx_block = false;
> -	client->knows_txdone = false;
> -
> -	kproc->mbox = mbox_request_channel(client, 0);
> -	if (IS_ERR(kproc->mbox)) {
> -		ret = -EBUSY;
> -		dev_err(dev, "mbox_request_channel failed: %ld\n",
> -			PTR_ERR(kproc->mbox));
> -		return ret;
> -	}
> -
> -	/*
> -	 * Ping the remote processor, this is only for sanity-sake for now;
> -	 * there is no functional effect whatsoever.
> -	 *
> -	 * Note that the reply will _not_ arrive immediately: this message
> -	 * will wait in the mailbox fifo until the remote processor is booted.
> -	 */
> -	ret = mbox_send_message(kproc->mbox, (void *)RP_MBOX_ECHO_REQUEST);
> -	if (ret < 0) {
> -		dev_err(dev, "mbox_send_message failed (%pe)\n", ERR_PTR(ret));
> -		mbox_free_channel(kproc->mbox);
> -		return ret;
> -	}
> -
> -	return 0;
> -}
> -/*
> - * The C66x DSP cores have a local reset that affects only the CPU, and a
> - * generic module reset that powers on the device and allows the DSP internal
> - * memories to be accessed while the local reset is asserted. This function is
> - * used to release the global reset on C66x DSPs to allow loading into the DSP
> - * internal RAMs. The .prepare() ops is invoked by remoteproc core before any
> - * firmware loading, and is followed by the .start() ops after loading to
> - * actually let the C66x DSP cores run. This callback is invoked only in
> - * remoteproc mode.
> - */
> -static int k3_dsp_rproc_prepare(struct rproc *rproc)
> -{
> -	struct k3_dsp_rproc *kproc = rproc->priv;
> -	struct device *dev = kproc->dev;
> -	int ret;
> -
> -	ret = kproc->ti_sci->ops.dev_ops.get_device(kproc->ti_sci,
> -						    kproc->ti_sci_id);
> -	if (ret)
> -		dev_err(dev, "module-reset deassert failed, cannot enable internal RAM loading (%pe)\n",
> -			ERR_PTR(ret));
> -
> -	return ret;
> -}
> -
> -/*
> - * This function implements the .unprepare() ops and performs the complimentary
> - * operations to that of the .prepare() ops. The function is used to assert the
> - * global reset on applicable C66x cores. This completes the second portion of
> - * powering down the C66x DSP cores. The cores themselves are only halted in the
> - * .stop() callback through the local reset, and the .unprepare() ops is invoked
> - * by the remoteproc core after the remoteproc is stopped to balance the global
> - * reset. This callback is invoked only in remoteproc mode.
> - */
> -static int k3_dsp_rproc_unprepare(struct rproc *rproc)
> -{
> -	struct k3_dsp_rproc *kproc = rproc->priv;
> -	struct device *dev = kproc->dev;
> -	int ret;
> -
> -	ret = kproc->ti_sci->ops.dev_ops.put_device(kproc->ti_sci,
> -						    kproc->ti_sci_id);
> -	if (ret)
> -		dev_err(dev, "module-reset assert failed (%pe)\n", ERR_PTR(ret));
> -
> -	return ret;
> -}
> -
> -/*
> - * Power up the DSP remote processor.
> - *
> - * This function will be invoked only after the firmware for this rproc
> - * was loaded, parsed successfully, and all of its resource requirements
> - * were met. This callback is invoked only in remoteproc mode.
> - */
> -static int k3_dsp_rproc_start(struct rproc *rproc)
> -{
> -	struct k3_dsp_rproc *kproc = rproc->priv;
> -	struct device *dev = kproc->dev;
> -	u32 boot_addr;
> -	int ret;
> -
> -	ret = k3_dsp_rproc_request_mbox(rproc);
> -	if (ret)
> -		return ret;
> -
> -	boot_addr = rproc->bootaddr;
> -	if (boot_addr & (kproc->data->boot_align_addr - 1)) {
> -		dev_err(dev, "invalid boot address 0x%x, must be aligned on a 0x%x boundary\n",
> -			boot_addr, kproc->data->boot_align_addr);
> -		ret = -EINVAL;
> -		goto put_mbox;
> -	}
> -
> -	dev_err(dev, "booting DSP core using boot addr = 0x%x\n", boot_addr);
> -	ret = ti_sci_proc_set_config(kproc->tsp, boot_addr, 0, 0);
> -	if (ret)
> -		goto put_mbox;
> -
> -	ret = k3_dsp_rproc_release(kproc);
> -	if (ret)
> -		goto put_mbox;
> -
> -	return 0;
> -
> -put_mbox:
> -	mbox_free_channel(kproc->mbox);
> -	return ret;
> -}
> -
> -/*
> - * Stop the DSP remote processor.
> - *
> - * This function puts the DSP processor into reset, and finishes processing
> - * of any pending messages. This callback is invoked only in remoteproc mode.
> - */
> -static int k3_dsp_rproc_stop(struct rproc *rproc)
> -{
> -	struct k3_dsp_rproc *kproc = rproc->priv;
> -
> -	mbox_free_channel(kproc->mbox);
> -
> -	k3_dsp_rproc_reset(kproc);
> -
> -	return 0;
> -}
> -
> -/*
> - * Attach to a running DSP remote processor (IPC-only mode)
> - *
> - * This rproc attach callback only needs to request the mailbox, the remote
> - * processor is already booted, so there is no need to issue any TI-SCI
> - * commands to boot the DSP core. This callback is invoked only in IPC-only
> - * mode.
> - */
> -static int k3_dsp_rproc_attach(struct rproc *rproc)
> -{
> -	struct k3_dsp_rproc *kproc = rproc->priv;
> -	struct device *dev = kproc->dev;
> -	int ret;
> -
> -	ret = k3_dsp_rproc_request_mbox(rproc);
> -	if (ret)
> -		return ret;
> -
> -	dev_info(dev, "DSP initialized in IPC-only mode\n");
> -	return 0;
> -}
> -
> -/*
> - * Detach from a running DSP remote processor (IPC-only mode)
> - *
> - * This rproc detach callback performs the opposite operation to attach callback
> - * and only needs to release the mailbox, the DSP core is not stopped and will
> - * be left to continue to run its booted firmware. This callback is invoked only
> - * in IPC-only mode.
> - */
> -static int k3_dsp_rproc_detach(struct rproc *rproc)
> -{
> -	struct k3_dsp_rproc *kproc = rproc->priv;
> -	struct device *dev = kproc->dev;
> -
> -	mbox_free_channel(kproc->mbox);
> -	dev_info(dev, "DSP deinitialized in IPC-only mode\n");
> -	return 0;
> -}
> -
> -/*
> - * This function implements the .get_loaded_rsc_table() callback and is used
> - * to provide the resource table for a booted DSP in IPC-only mode. The K3 DSP
> - * firmwares follow a design-by-contract approach and are expected to have the
> - * resource table at the base of the DDR region reserved for firmware usage.
> - * This provides flexibility for the remote processor to be booted by different
> - * bootloaders that may or may not have the ability to publish the resource table
> - * address and size through a DT property. This callback is invoked only in
> - * IPC-only mode.
> - */
> -static struct resource_table *k3_dsp_get_loaded_rsc_table(struct rproc *rproc,
> -							  size_t *rsc_table_sz)
> -{
> -	struct k3_dsp_rproc *kproc = rproc->priv;
> -	struct device *dev = kproc->dev;
> -
> -	if (!kproc->rmem[0].cpu_addr) {
> -		dev_err(dev, "memory-region #1 does not exist, loaded rsc table can't be found");
> -		return ERR_PTR(-ENOMEM);
> -	}
> -
> -	/*
> -	 * NOTE: The resource table size is currently hard-coded to a maximum
> -	 * of 256 bytes. The most common resource table usage for K3 firmwares
> -	 * is to only have the vdev resource entry and an optional trace entry.
> -	 * The exact size could be computed based on resource table address, but
> -	 * the hard-coded value suffices to support the IPC-only mode.
> -	 */
> -	*rsc_table_sz = 256;
> -	return (struct resource_table *)kproc->rmem[0].cpu_addr;
> -}
> -
> -/*
> - * Custom function to translate a DSP device address (internal RAMs only) to a
> - * kernel virtual address.  The DSPs can access their RAMs at either an internal
> - * address visible only from a DSP, or at the SoC-level bus address. Both these
> - * addresses need to be looked through for translation. The translated addresses
> - * can be used either by the remoteproc core for loading (when using kernel
> - * remoteproc loader), or by any rpmsg bus drivers.
> - */
> -static void *k3_dsp_rproc_da_to_va(struct rproc *rproc, u64 da, size_t len, bool *is_iomem)
> -{
> -	struct k3_dsp_rproc *kproc = rproc->priv;
> -	void __iomem *va = NULL;
> -	phys_addr_t bus_addr;
> -	u32 dev_addr, offset;
> -	size_t size;
> -	int i;
> -
> -	if (len == 0)
> -		return NULL;
> -
> -	for (i = 0; i < kproc->num_mems; i++) {
> -		bus_addr = kproc->mem[i].bus_addr;
> -		dev_addr = kproc->mem[i].dev_addr;
> -		size = kproc->mem[i].size;
> -
> -		if (da < KEYSTONE_RPROC_LOCAL_ADDRESS_MASK) {
> -			/* handle DSP-view addresses */
> -			if (da >= dev_addr &&
> -			    ((da + len) <= (dev_addr + size))) {
> -				offset = da - dev_addr;
> -				va = kproc->mem[i].cpu_addr + offset;
> -				return (__force void *)va;
> -			}
> -		} else {
> -			/* handle SoC-view addresses */
> -			if (da >= bus_addr &&
> -			    (da + len) <= (bus_addr + size)) {
> -				offset = da - bus_addr;
> -				va = kproc->mem[i].cpu_addr + offset;
> -				return (__force void *)va;
> -			}
> -		}
> -	}
> -
> -	/* handle static DDR reserved memory regions */
> -	for (i = 0; i < kproc->num_rmems; i++) {
> -		dev_addr = kproc->rmem[i].dev_addr;
> -		size = kproc->rmem[i].size;
> -
> -		if (da >= dev_addr && ((da + len) <= (dev_addr + size))) {
> -			offset = da - dev_addr;
> -			va = kproc->rmem[i].cpu_addr + offset;
> -			return (__force void *)va;
> -		}
> -	}
> -
> -	return NULL;
> -}
> -
> -static const struct rproc_ops k3_dsp_rproc_ops = {
> -	.start		= k3_dsp_rproc_start,
> -	.stop		= k3_dsp_rproc_stop,
> -	.kick		= k3_dsp_rproc_kick,
> -	.da_to_va	= k3_dsp_rproc_da_to_va,
> -};
> -
> -static int k3_dsp_rproc_of_get_memories(struct platform_device *pdev,
> -					struct k3_dsp_rproc *kproc)
> -{
> -	const struct k3_dsp_dev_data *data = kproc->data;
> -	struct device *dev = &pdev->dev;
> -	struct resource *res;
> -	int num_mems = 0;
> -	int i;
> -
> -	num_mems = kproc->data->num_mems;
> -	kproc->mem = devm_kcalloc(kproc->dev, num_mems,
> -				  sizeof(*kproc->mem), GFP_KERNEL);
> -	if (!kproc->mem)
> -		return -ENOMEM;
> -
> -	for (i = 0; i < num_mems; i++) {
> -		res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
> -						   data->mems[i].name);
> -		if (!res) {
> -			dev_err(dev, "found no memory resource for %s\n",
> -				data->mems[i].name);
> -			return -EINVAL;
> -		}
> -		if (!devm_request_mem_region(dev, res->start,
> -					     resource_size(res),
> -					     dev_name(dev))) {
> -			dev_err(dev, "could not request %s region for resource\n",
> -				data->mems[i].name);
> -			return -EBUSY;
> -		}
> -
> -		kproc->mem[i].cpu_addr = devm_ioremap_wc(dev, res->start,
> -							 resource_size(res));
> -		if (!kproc->mem[i].cpu_addr) {
> -			dev_err(dev, "failed to map %s memory\n",
> -				data->mems[i].name);
> -			return -ENOMEM;
> -		}
> -		kproc->mem[i].bus_addr = res->start;
> -		kproc->mem[i].dev_addr = data->mems[i].dev_addr;
> -		kproc->mem[i].size = resource_size(res);
> -
> -		dev_dbg(dev, "memory %8s: bus addr %pa size 0x%zx va %pK da 0x%x\n",
> -			data->mems[i].name, &kproc->mem[i].bus_addr,
> -			kproc->mem[i].size, kproc->mem[i].cpu_addr,
> -			kproc->mem[i].dev_addr);
> -	}
> -	kproc->num_mems = num_mems;
> -
> -	return 0;
> -}
> -
> -static int k3_dsp_reserved_mem_init(struct k3_dsp_rproc *kproc)
> -{
> -	struct device *dev = kproc->dev;
> -	struct device_node *np = dev->of_node;
> -	struct device_node *rmem_np;
> -	struct reserved_mem *rmem;
> -	int num_rmems;
> -	int ret, i;
> -
> -	num_rmems = of_property_count_elems_of_size(np, "memory-region",
> -						    sizeof(phandle));
> -	if (num_rmems < 0) {
> -		dev_err(dev, "device does not reserved memory regions (%pe)\n",
> -			ERR_PTR(num_rmems));
> -		return -EINVAL;
> -	}
> -	if (num_rmems < 2) {
> -		dev_err(dev, "device needs at least two memory regions to be defined, num = %d\n",
> -			num_rmems);
> -		return -EINVAL;
> -	}
> -
> -	/* use reserved memory region 0 for vring DMA allocations */
> -	ret = of_reserved_mem_device_init_by_idx(dev, np, 0);
> -	if (ret) {
> -		dev_err(dev, "device cannot initialize DMA pool (%pe)\n",
> -			ERR_PTR(ret));
> -		return ret;
> -	}
> -
> -	num_rmems--;
> -	kproc->rmem = kcalloc(num_rmems, sizeof(*kproc->rmem), GFP_KERNEL);
> -	if (!kproc->rmem) {
> -		ret = -ENOMEM;
> -		goto release_rmem;
> -	}
> -
> -	/* use remaining reserved memory regions for static carveouts */
> -	for (i = 0; i < num_rmems; i++) {
> -		rmem_np = of_parse_phandle(np, "memory-region", i + 1);
> -		if (!rmem_np) {
> -			ret = -EINVAL;
> -			goto unmap_rmem;
> -		}
> -
> -		rmem = of_reserved_mem_lookup(rmem_np);
> -		if (!rmem) {
> -			of_node_put(rmem_np);
> -			ret = -EINVAL;
> -			goto unmap_rmem;
> -		}
> -		of_node_put(rmem_np);
> -
> -		kproc->rmem[i].bus_addr = rmem->base;
> -		/* 64-bit address regions currently not supported */
> -		kproc->rmem[i].dev_addr = (u32)rmem->base;
> -		kproc->rmem[i].size = rmem->size;
> -		kproc->rmem[i].cpu_addr = ioremap_wc(rmem->base, rmem->size);
> -		if (!kproc->rmem[i].cpu_addr) {
> -			dev_err(dev, "failed to map reserved memory#%d at %pa of size %pa\n",
> -				i + 1, &rmem->base, &rmem->size);
> -			ret = -ENOMEM;
> -			goto unmap_rmem;
> -		}
> -
> -		dev_dbg(dev, "reserved memory%d: bus addr %pa size 0x%zx va %pK da 0x%x\n",
> -			i + 1, &kproc->rmem[i].bus_addr,
> -			kproc->rmem[i].size, kproc->rmem[i].cpu_addr,
> -			kproc->rmem[i].dev_addr);
> -	}
> -	kproc->num_rmems = num_rmems;
> -
> -	return 0;
> -
> -unmap_rmem:
> -	for (i--; i >= 0; i--)
> -		iounmap(kproc->rmem[i].cpu_addr);
> -	kfree(kproc->rmem);
> -release_rmem:
> -	of_reserved_mem_device_release(kproc->dev);
> -	return ret;
> -}
> -
> -static void k3_dsp_reserved_mem_exit(struct k3_dsp_rproc *kproc)
> -{
> -	int i;
> -
> -	for (i = 0; i < kproc->num_rmems; i++)
> -		iounmap(kproc->rmem[i].cpu_addr);
> -	kfree(kproc->rmem);
> -
> -	of_reserved_mem_device_release(kproc->dev);
> -}
> -
> -static
> -struct ti_sci_proc *k3_dsp_rproc_of_get_tsp(struct device *dev,
> -					    const struct ti_sci_handle *sci)
> -{
> -	struct ti_sci_proc *tsp;
> -	u32 temp[2];
> -	int ret;
> -
> -	ret = of_property_read_u32_array(dev->of_node, "ti,sci-proc-ids",
> -					 temp, 2);
> -	if (ret < 0)
> -		return ERR_PTR(ret);
> -
> -	tsp = kzalloc(sizeof(*tsp), GFP_KERNEL);
> -	if (!tsp)
> -		return ERR_PTR(-ENOMEM);
> -
> -	tsp->dev = dev;
> -	tsp->sci = sci;
> -	tsp->ops = &sci->ops.proc_ops;
> -	tsp->proc_id = temp[0];
> -	tsp->host_id = temp[1];
> -
> -	return tsp;
> -}
> -
> -static int k3_dsp_rproc_probe(struct platform_device *pdev)
> -{
> -	struct device *dev = &pdev->dev;
> -	struct device_node *np = dev->of_node;
> -	const struct k3_dsp_dev_data *data;
> -	struct k3_dsp_rproc *kproc;
> -	struct rproc *rproc;
> -	const char *fw_name;
> -	bool p_state = false;
> -	int ret = 0;
> -	int ret1;
> -
> -	data = of_device_get_match_data(dev);
> -	if (!data)
> -		return -ENODEV;
> -
> -	ret = rproc_of_parse_firmware(dev, 0, &fw_name);
> -	if (ret)
> -		return dev_err_probe(dev, ret, "failed to parse firmware-name property\n");
> -
> -	rproc = rproc_alloc(dev, dev_name(dev), &k3_dsp_rproc_ops, fw_name,
> -			    sizeof(*kproc));
> -	if (!rproc)
> -		return -ENOMEM;
> -
> -	rproc->has_iommu = false;
> -	rproc->recovery_disabled = true;
> -	if (data->uses_lreset) {
> -		rproc->ops->prepare = k3_dsp_rproc_prepare;
> -		rproc->ops->unprepare = k3_dsp_rproc_unprepare;
> -	}
> -	kproc = rproc->priv;
> -	kproc->rproc = rproc;
> -	kproc->dev = dev;
> -	kproc->data = data;
> -
> -	kproc->ti_sci = ti_sci_get_by_phandle(np, "ti,sci");
> -	if (IS_ERR(kproc->ti_sci)) {
> -		ret = dev_err_probe(dev, PTR_ERR(kproc->ti_sci),
> -				    "failed to get ti-sci handle\n");
> -		kproc->ti_sci = NULL;
> -		goto free_rproc;
> -	}
> -
> -	ret = of_property_read_u32(np, "ti,sci-dev-id", &kproc->ti_sci_id);
> -	if (ret) {
> -		dev_err_probe(dev, ret, "missing 'ti,sci-dev-id' property\n");
> -		goto put_sci;
> -	}
> -
> -	kproc->reset = devm_reset_control_get_exclusive(dev, NULL);
> -	if (IS_ERR(kproc->reset)) {
> -		ret = dev_err_probe(dev, PTR_ERR(kproc->reset),
> -				    "failed to get reset\n");
> -		goto put_sci;
> -	}
> -
> -	kproc->tsp = k3_dsp_rproc_of_get_tsp(dev, kproc->ti_sci);
> -	if (IS_ERR(kproc->tsp)) {
> -		ret = dev_err_probe(dev, PTR_ERR(kproc->tsp),
> -				    "failed to construct ti-sci proc control\n");
> -		goto put_sci;
> -	}
> -
> -	ret = ti_sci_proc_request(kproc->tsp);
> -	if (ret < 0) {
> -		dev_err_probe(dev, ret, "ti_sci_proc_request failed\n");
> -		goto free_tsp;
> -	}
> -
> -	ret = k3_dsp_rproc_of_get_memories(pdev, kproc);
> -	if (ret)
> -		goto release_tsp;
> -
> -	ret = k3_dsp_reserved_mem_init(kproc);
> -	if (ret) {
> -		dev_err_probe(dev, ret, "reserved memory init failed\n");
> -		goto release_tsp;
> -	}
> -
> -	ret = kproc->ti_sci->ops.dev_ops.is_on(kproc->ti_sci, kproc->ti_sci_id,
> -					       NULL, &p_state);
> -	if (ret) {
> -		dev_err_probe(dev, ret, "failed to get initial state, mode cannot be determined\n");
> -		goto release_mem;
> -	}
> -
> -	/* configure J721E devices for either remoteproc or IPC-only mode */
> -	if (p_state) {
> -		dev_info(dev, "configured DSP for IPC-only mode\n");
> -		rproc->state = RPROC_DETACHED;
> -		/* override rproc ops with only required IPC-only mode ops */
> -		rproc->ops->prepare = NULL;
> -		rproc->ops->unprepare = NULL;
> -		rproc->ops->start = NULL;
> -		rproc->ops->stop = NULL;
> -		rproc->ops->attach = k3_dsp_rproc_attach;
> -		rproc->ops->detach = k3_dsp_rproc_detach;
> -		rproc->ops->get_loaded_rsc_table = k3_dsp_get_loaded_rsc_table;
> -	} else {
> -		dev_info(dev, "configured DSP for remoteproc mode\n");
> -		/*
> -		 * ensure the DSP local reset is asserted to ensure the DSP
> -		 * doesn't execute bogus code in .prepare() when the module
> -		 * reset is released.
> -		 */
> -		if (data->uses_lreset) {
> -			ret = reset_control_status(kproc->reset);
> -			if (ret < 0) {
> -				dev_err_probe(dev, ret, "failed to get reset status\n");
> -				goto release_mem;
> -			} else if (ret == 0) {
> -				dev_warn(dev, "local reset is deasserted for device\n");
> -				k3_dsp_rproc_reset(kproc);
> -			}
> -		}
> -	}
> -
> -	ret = rproc_add(rproc);
> -	if (ret) {
> -		dev_err_probe(dev, ret, "failed to add register device with remoteproc core\n");
> -		goto release_mem;
> -	}
> -
> -	platform_set_drvdata(pdev, kproc);
> -
> -	return 0;
> -
> -release_mem:
> -	k3_dsp_reserved_mem_exit(kproc);
> -release_tsp:
> -	ret1 = ti_sci_proc_release(kproc->tsp);
> -	if (ret1)
> -		dev_err(dev, "failed to release proc (%pe)\n", ERR_PTR(ret1));
> -free_tsp:
> -	kfree(kproc->tsp);
> -put_sci:
> -	ret1 = ti_sci_put_handle(kproc->ti_sci);
> -	if (ret1)
> -		dev_err(dev, "failed to put ti_sci handle (%pe)\n", ERR_PTR(ret1));
> -free_rproc:
> -	rproc_free(rproc);
> -	return ret;
> -}
> -
> -static void k3_dsp_rproc_remove(struct platform_device *pdev)
> -{
> -	struct k3_dsp_rproc *kproc = platform_get_drvdata(pdev);
> -	struct rproc *rproc = kproc->rproc;
> -	struct device *dev = &pdev->dev;
> -	int ret;
> -
> -	if (rproc->state == RPROC_ATTACHED) {
> -		ret = rproc_detach(rproc);
> -		if (ret) {
> -			/* Note this error path leaks resources */
> -			dev_err(dev, "failed to detach proc (%pe)\n", ERR_PTR(ret));
> -			return;
> -		}
> -	}
> -
> -	rproc_del(kproc->rproc);
> -
> -	ret = ti_sci_proc_release(kproc->tsp);
> -	if (ret)
> -		dev_err(dev, "failed to release proc (%pe)\n", ERR_PTR(ret));
> -
> -	kfree(kproc->tsp);
> -
> -	ret = ti_sci_put_handle(kproc->ti_sci);
> -	if (ret)
> -		dev_err(dev, "failed to put ti_sci handle (%pe)\n", ERR_PTR(ret));
> -
> -	k3_dsp_reserved_mem_exit(kproc);
> -	rproc_free(kproc->rproc);
> -}
> -
> -static const struct k3_dsp_mem_data c66_mems[] = {
> -	{ .name = "l2sram", .dev_addr = 0x800000 },
> -	{ .name = "l1pram", .dev_addr = 0xe00000 },
> -	{ .name = "l1dram", .dev_addr = 0xf00000 },
> -};
> -
> -/* C71x cores only have a L1P Cache, there are no L1P SRAMs */
> -static const struct k3_dsp_mem_data c71_mems[] = {
> -	{ .name = "l2sram", .dev_addr = 0x800000 },
> -	{ .name = "l1dram", .dev_addr = 0xe00000 },
> -};
> -
> -static const struct k3_dsp_mem_data c7xv_mems[] = {
> -	{ .name = "l2sram", .dev_addr = 0x800000 },
> -};
> -
> -static const struct k3_dsp_dev_data c66_data = {
> -	.mems = c66_mems,
> -	.num_mems = ARRAY_SIZE(c66_mems),
> -	.boot_align_addr = SZ_1K,
> -	.uses_lreset = true,
> -};
> -
> -static const struct k3_dsp_dev_data c71_data = {
> -	.mems = c71_mems,
> -	.num_mems = ARRAY_SIZE(c71_mems),
> -	.boot_align_addr = SZ_2M,
> -	.uses_lreset = false,
> -};
> -
> -static const struct k3_dsp_dev_data c7xv_data = {
> -	.mems = c7xv_mems,
> -	.num_mems = ARRAY_SIZE(c7xv_mems),
> -	.boot_align_addr = SZ_2M,
> -	.uses_lreset = false,
> -};
> -
> -static const struct of_device_id k3_dsp_of_match[] = {
> -	{ .compatible = "ti,j721e-c66-dsp", .data = &c66_data, },
> -	{ .compatible = "ti,j721e-c71-dsp", .data = &c71_data, },
> -	{ .compatible = "ti,j721s2-c71-dsp", .data = &c71_data, },
> -	{ .compatible = "ti,am62a-c7xv-dsp", .data = &c7xv_data, },
> -	{ /* sentinel */ },
> -};
> -MODULE_DEVICE_TABLE(of, k3_dsp_of_match);
> -
> -static struct platform_driver k3_dsp_rproc_driver = {
> -	.probe	= k3_dsp_rproc_probe,
> -	.remove_new = k3_dsp_rproc_remove,
> -	.driver	= {
> -		.name = "k3-dsp-rproc",
> -		.of_match_table = k3_dsp_of_match,
> -	},
> -};
> -
> -module_platform_driver(k3_dsp_rproc_driver);
> -
> -MODULE_AUTHOR("Suman Anna <s-anna@ti.com>");
> -MODULE_LICENSE("GPL v2");
> -MODULE_DESCRIPTION("TI K3 DSP Remoteproc driver");
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * TI K3 DSP Remote Processor(s) driver
> + *
> + * Copyright (C) 2018-2022 Texas Instruments Incorporated - https://www.ti.com/
> + *	Suman Anna <s-anna@ti.com>
> + */
> +
> +#include <linux/io.h>
> +#include <linux/mailbox_client.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_reserved_mem.h>
> +#include <linux/omap-mailbox.h>
> +#include <linux/platform_device.h>
> +#include <linux/remoteproc.h>
> +#include <linux/reset.h>
> +#include <linux/slab.h>
> +
> +#include "omap_remoteproc.h"
> +#include "remoteproc_internal.h"
> +#include "ti_sci_proc.h"
> +#include "ti_k3_common.h"
> +
> +/*
> + * Power up the DSP remote processor.
> + *
> + * This function will be invoked only after the firmware for this rproc
> + * was loaded, parsed successfully, and all of its resource requirements
> + * were met. This callback is invoked only in remoteproc mode.
> + */
> +static int k3_dsp_rproc_start(struct rproc *rproc)
> +{
> +	struct k3_rproc *kproc = rproc->priv;
> +	struct device *dev = kproc->dev;
> +	u32 boot_addr;
> +	int ret;
> +
> +	ret = k3_rproc_request_mbox(rproc);
> +	if (ret)
> +		return ret;
> +
> +	boot_addr = rproc->bootaddr;
> +	if (boot_addr & (kproc->data->boot_align_addr - 1)) {
> +		dev_err(dev, "invalid boot address 0x%x, must be aligned on a 0x%x boundary\n",
> +			boot_addr, kproc->data->boot_align_addr);
> +		ret = -EINVAL;
> +		goto put_mbox;
> +	}
> +
> +	dev_err(dev, "booting DSP core using boot addr = 0x%x\n", boot_addr);
> +	ret = ti_sci_proc_set_config(kproc->tsp, boot_addr, 0, 0);
> +	if (ret)
> +		goto put_mbox;
> +
> +	ret = k3_rproc_release(kproc);
> +	if (ret)
> +		goto put_mbox;
> +
> +	return 0;
> +
> +put_mbox:
> +	mbox_free_channel(kproc->mbox);
> +	return ret;
> +}
> +
> +/*
> + * Stop the DSP remote processor.
> + *
> + * This function puts the DSP processor into reset, and finishes processing
> + * of any pending messages. This callback is invoked only in remoteproc mode.
> + */
> +static int k3_dsp_rproc_stop(struct rproc *rproc)
> +{
> +	struct k3_rproc *kproc = rproc->priv;
> +
> +	mbox_free_channel(kproc->mbox);
> +
> +	k3_rproc_reset(kproc);
> +
> +	return 0;
> +}
> +
> +/*
> + * Attach to a running DSP remote processor (IPC-only mode)
> + *
> + * This rproc attach callback only needs to request the mailbox, the remote
> + * processor is already booted, so there is no need to issue any TI-SCI
> + * commands to boot the DSP core. This callback is invoked only in IPC-only
> + * mode.
> + */
> +static int k3_dsp_rproc_attach(struct rproc *rproc)
> +{
> +	struct k3_rproc *kproc = rproc->priv;
> +	struct device *dev = kproc->dev;
> +	int ret;
> +
> +	ret = k3_rproc_request_mbox(rproc);
> +	if (ret)
> +		return ret;
> +
> +	dev_info(dev, "DSP initialized in IPC-only mode\n");
> +	return 0;
> +}
> +
> +/*
> + * Detach from a running DSP remote processor (IPC-only mode)
> + *
> + * This rproc detach callback performs the opposite operation to attach callback
> + * and only needs to release the mailbox, the DSP core is not stopped and will
> + * be left to continue to run its booted firmware. This callback is invoked only
> + * in IPC-only mode.
> + */
> +static int k3_dsp_rproc_detach(struct rproc *rproc)
> +{
> +	struct k3_rproc *kproc = rproc->priv;
> +	struct device *dev = kproc->dev;
> +
> +	mbox_free_channel(kproc->mbox);
> +	dev_info(dev, "DSP deinitialized in IPC-only mode\n");
> +	return 0;
> +}
> +
> +
> +static const struct rproc_ops k3_dsp_rproc_ops = {
> +	.start		= k3_dsp_rproc_start,
> +	.stop		= k3_dsp_rproc_stop,
> +	.kick		= k3_rproc_kick,
> +	.da_to_va	= k3_rproc_da_to_va,
> +};
> +
> +static int k3_dsp_rproc_probe(struct platform_device *pdev)
> +{
> +	struct device *dev = &pdev->dev;
> +	struct device_node *np = dev->of_node;
> +	const struct k3_rproc_dev_data *data;
> +	struct k3_rproc *kproc;
> +	struct rproc *rproc;
> +	const char *fw_name;
> +	bool p_state = false;
> +	int ret = 0;
> +	int ret1;
> +
> +	data = of_device_get_match_data(dev);
> +	if (!data)
> +		return -ENODEV;
> +
> +	ret = rproc_of_parse_firmware(dev, 0, &fw_name);
> +	if (ret)
> +		return dev_err_probe(dev, ret, "failed to parse firmware-name property\n");
> +
> +	rproc = rproc_alloc(dev, dev_name(dev), &k3_dsp_rproc_ops, fw_name,
> +			    sizeof(*kproc));
> +	if (!rproc)
> +		return -ENOMEM;
> +
> +	rproc->has_iommu = false;
> +	rproc->recovery_disabled = true;
> +	if (data->uses_lreset) {
> +		rproc->ops->prepare = k3_rproc_prepare;
> +		rproc->ops->unprepare = k3_rproc_unprepare;
> +	}
> +	kproc = rproc->priv;
> +	kproc->rproc = rproc;
> +	kproc->dev = dev;
> +	kproc->data = data;
> +
> +	kproc->ti_sci = ti_sci_get_by_phandle(np, "ti,sci");
> +	if (IS_ERR(kproc->ti_sci)) {
> +		ret = dev_err_probe(dev, PTR_ERR(kproc->ti_sci),
> +				    "failed to get ti-sci handle\n");
> +		kproc->ti_sci = NULL;
> +		goto free_rproc;
> +	}
> +
> +	ret = of_property_read_u32(np, "ti,sci-dev-id", &kproc->ti_sci_id);
> +	if (ret) {
> +		dev_err_probe(dev, ret, "missing 'ti,sci-dev-id' property\n");
> +		goto put_sci;
> +	}
> +
> +	kproc->reset = devm_reset_control_get_exclusive(dev, NULL);
> +	if (IS_ERR(kproc->reset)) {
> +		ret = dev_err_probe(dev, PTR_ERR(kproc->reset),
> +				    "failed to get reset\n");
> +		goto put_sci;
> +	}
> +
> +	kproc->tsp = k3_rproc_of_get_tsp(dev, kproc->ti_sci);
> +	if (IS_ERR(kproc->tsp)) {
> +		ret = dev_err_probe(dev, PTR_ERR(kproc->tsp),
> +				    "failed to construct ti-sci proc control\n");
> +		goto put_sci;
> +	}
> +
> +	ret = ti_sci_proc_request(kproc->tsp);
> +	if (ret < 0) {
> +		dev_err_probe(dev, ret, "ti_sci_proc_request failed\n");
> +		goto free_tsp;
> +	}
> +
> +	ret = k3_rproc_of_get_memories(pdev, kproc);
> +	if (ret)
> +		goto release_tsp;
> +
> +	ret = k3_reserved_mem_init(kproc);
> +	if (ret) {
> +		dev_err_probe(dev, ret, "reserved memory init failed\n");
> +		goto release_tsp;
> +	}
> +
> +	ret = kproc->ti_sci->ops.dev_ops.is_on(kproc->ti_sci, kproc->ti_sci_id,
> +					       NULL, &p_state);
> +	if (ret) {
> +		dev_err_probe(dev, ret, "failed to get initial state, mode cannot be determined\n");
> +		goto release_mem;
> +	}
> +
> +	/* configure J721E devices for either remoteproc or IPC-only mode */
> +	if (p_state) {
> +		dev_info(dev, "configured DSP for IPC-only mode\n");
> +		rproc->state = RPROC_DETACHED;
> +		/* override rproc ops with only required IPC-only mode ops */
> +		rproc->ops->prepare = NULL;
> +		rproc->ops->unprepare = NULL;
> +		rproc->ops->start = NULL;
> +		rproc->ops->stop = NULL;
> +		rproc->ops->attach = k3_dsp_rproc_attach;
> +		rproc->ops->detach = k3_dsp_rproc_detach;
> +		rproc->ops->get_loaded_rsc_table = k3_get_loaded_rsc_table;
> +	} else {
> +		dev_info(dev, "configured DSP for remoteproc mode\n");
> +		/*
> +		 * ensure the DSP local reset is asserted to ensure the DSP
> +		 * doesn't execute bogus code in .prepare() when the module
> +		 * reset is released.
> +		 */
> +		if (data->uses_lreset) {
> +			ret = reset_control_status(kproc->reset);
> +			if (ret < 0) {
> +				dev_err_probe(dev, ret, "failed to get reset status\n");
> +				goto release_mem;
> +			} else if (ret == 0) {
> +				dev_warn(dev, "local reset is deasserted for device\n");
> +				k3_rproc_reset(kproc);
> +			}
> +		}
> +	}
> +
> +	ret = rproc_add(rproc);
> +	if (ret) {
> +		dev_err_probe(dev, ret, "failed to add register device with remoteproc core\n");
> +		goto release_mem;
> +	}
> +
> +	platform_set_drvdata(pdev, kproc);
> +
> +	return 0;
> +
> +release_mem:
> +	k3_reserved_mem_exit(kproc);
> +release_tsp:
> +	ret1 = ti_sci_proc_release(kproc->tsp);
> +	if (ret1)
> +		dev_err(dev, "failed to release proc (%pe)\n", ERR_PTR(ret1));
> +free_tsp:
> +	kfree(kproc->tsp);
> +put_sci:
> +	ret1 = ti_sci_put_handle(kproc->ti_sci);
> +	if (ret1)
> +		dev_err(dev, "failed to put ti_sci handle (%pe)\n", ERR_PTR(ret1));
> +free_rproc:
> +	rproc_free(rproc);
> +	return ret;
> +}
> +
> +static void k3_dsp_rproc_remove(struct platform_device *pdev)
> +{
> +	struct k3_rproc *kproc = platform_get_drvdata(pdev);
> +	struct rproc *rproc = kproc->rproc;
> +	struct device *dev = &pdev->dev;
> +	int ret;
> +
> +	if (rproc->state == RPROC_ATTACHED) {
> +		ret = rproc_detach(rproc);
> +		if (ret) {
> +			/* Note this error path leaks resources */
> +			dev_err(dev, "failed to detach proc (%pe)\n", ERR_PTR(ret));
> +			return;
> +		}
> +	}
> +
> +	rproc_del(kproc->rproc);
> +
> +	ret = ti_sci_proc_release(kproc->tsp);
> +	if (ret)
> +		dev_err(dev, "failed to release proc (%pe)\n", ERR_PTR(ret));
> +
> +	kfree(kproc->tsp);
> +
> +	ret = ti_sci_put_handle(kproc->ti_sci);
> +	if (ret)
> +		dev_err(dev, "failed to put ti_sci handle (%pe)\n", ERR_PTR(ret));
> +
> +	k3_reserved_mem_exit(kproc);
> +	rproc_free(kproc->rproc);
> +}
> +
> +static const struct k3_rproc_mem_data c66_mems[] = {
> +	{ .name = "l2sram", .dev_addr = 0x800000 },
> +	{ .name = "l1pram", .dev_addr = 0xe00000 },
> +	{ .name = "l1dram", .dev_addr = 0xf00000 },
> +};
> +
> +/* C71x cores only have a L1P Cache, there are no L1P SRAMs */
> +static const struct k3_rproc_mem_data c71_mems[] = {
> +	{ .name = "l2sram", .dev_addr = 0x800000 },
> +	{ .name = "l1dram", .dev_addr = 0xe00000 },
> +};
> +
> +static const struct k3_rproc_mem_data c7xv_mems[] = {
> +	{ .name = "l2sram", .dev_addr = 0x800000 },
> +};
> +
> +static const struct k3_rproc_dev_data c66_data = {
> +	.mems = c66_mems,
> +	.num_mems = ARRAY_SIZE(c66_mems),
> +	.boot_align_addr = SZ_1K,
> +	.uses_lreset = true,
> +};
> +
> +static const struct k3_rproc_dev_data c71_data = {
> +	.mems = c71_mems,
> +	.num_mems = ARRAY_SIZE(c71_mems),
> +	.boot_align_addr = SZ_2M,
> +	.uses_lreset = false,
> +};
> +
> +static const struct k3_rproc_dev_data c7xv_data = {
> +	.mems = c7xv_mems,
> +	.num_mems = ARRAY_SIZE(c7xv_mems),
> +	.boot_align_addr = SZ_2M,
> +	.uses_lreset = false,
> +};
> +
> +static const struct of_device_id k3_dsp_of_match[] = {
> +	{ .compatible = "ti,j721e-c66-dsp", .data = &c66_data, },
> +	{ .compatible = "ti,j721e-c71-dsp", .data = &c71_data, },
> +	{ .compatible = "ti,j721s2-c71-dsp", .data = &c71_data, },
> +	{ .compatible = "ti,am62a-c7xv-dsp", .data = &c7xv_data, },
> +	{ /* sentinel */ },
> +};
> +MODULE_DEVICE_TABLE(of, k3_dsp_of_match);
> +
> +static struct platform_driver k3_dsp_rproc_driver = {
> +	.probe	= k3_dsp_rproc_probe,
> +	.remove_new = k3_dsp_rproc_remove,
> +	.driver	= {
> +		.name = "k3-dsp-rproc",
> +		.of_match_table = k3_dsp_of_match,
> +	},
> +};
> +
> +module_platform_driver(k3_dsp_rproc_driver);
> +
> +MODULE_AUTHOR("Suman Anna <s-anna@ti.com>");
> +MODULE_LICENSE("GPL v2");
> +MODULE_DESCRIPTION("TI K3 DSP Remoteproc driver");

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v7 4/5] remoteproc: k3-m4: Add a remoteproc driver for M4F subsystem

[Hari Nagalla]

From: Martyn Welch <martyn.welch@collabora.com>

The AM62x and AM64x SoCs of the TI K3 family has a Cortex M4F core in
the MCU domain. This core is typically used for safety applications in a
stand alone mode. However, some application (non safety related) may
want to use the M4F core as a generic remote processor with IPC to the
host processor. The M4F core has internal IRAM and DRAM memories and are
exposed to the system bus for code and data loading.

A remote processor driver is added to support this subsystem, including
being able to load and boot the M4F core. Loading includes to M4F
internal memories and predefined external code/data memories. The
carve outs for external contiguous memory is defined in the M4F device
node and should match with the external memory declarations in the M4F
image binary. The M4F subsystem has two resets. One reset is for the
entire subsystem i.e including the internal memories and the other, a
local reset is only for the M4F processing core. When loading the image,
the driver first releases the subsystem reset, loads the firmware image
and then releases the local reset to let the M4F processing core run.

Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
---
changes since v6:
 - Added compile testing.
 - replaced 'dev_err' with 'dev_err_probe'
 - removed redundant calls to existing code

link to v6:
https://lore.kernel.org/all/20230913111644.29889-5-hnagalla@ti.com/

build logs: https://paste.sr.ht/~hnagalla/be9d1c45e176ea8fa274ab13a3da43a9853fcf7f 

 drivers/remoteproc/Kconfig               |  13 +
 drivers/remoteproc/Makefile              |   1 +
 drivers/remoteproc/ti_k3_m4_remoteproc.c | 327 +++++++++++++++++++++++
 3 files changed, 341 insertions(+)
 create mode 100644 drivers/remoteproc/ti_k3_m4_remoteproc.c

diff --git a/drivers/remoteproc/Kconfig b/drivers/remoteproc/Kconfig
index 48845dc8fa85..1a7c0330c91a 100644
--- a/drivers/remoteproc/Kconfig
+++ b/drivers/remoteproc/Kconfig
@@ -339,6 +339,19 @@ config TI_K3_DSP_REMOTEPROC
 	  It's safe to say N here if you're not interested in utilizing
 	  the DSP slave processors.
 
+config TI_K3_M4_REMOTEPROC
+	tristate "TI K3 M4 remoteproc support"
+	depends on ARCH_K3 || COMPILE_TEST
+	select MAILBOX
+	select OMAP2PLUS_MBOX
+	help
+	  Say m here to support TI's M4 remote processor subsystems
+	  on various TI K3 family of SoCs through the remote processor
+	  framework.
+
+	  It's safe to say N here if you're not interested in utilizing
+	  a remote processor.
+
 config TI_K3_R5_REMOTEPROC
 	tristate "TI K3 R5 remoteproc support"
 	depends on ARCH_K3
diff --git a/drivers/remoteproc/Makefile b/drivers/remoteproc/Makefile
index 55c552e27a45..e30908ca4bfc 100644
--- a/drivers/remoteproc/Makefile
+++ b/drivers/remoteproc/Makefile
@@ -37,5 +37,6 @@ obj-$(CONFIG_ST_REMOTEPROC)		+= st_remoteproc.o
 obj-$(CONFIG_ST_SLIM_REMOTEPROC)	+= st_slim_rproc.o
 obj-$(CONFIG_STM32_RPROC)		+= stm32_rproc.o
 obj-$(CONFIG_TI_K3_DSP_REMOTEPROC)	+= ti_k3_dsp_remoteproc.o ti_k3_common.o
+obj-$(CONFIG_TI_K3_M4_REMOTEPROC)	+= ti_k3_m4_remoteproc.o ti_k3_common.o
 obj-$(CONFIG_TI_K3_R5_REMOTEPROC)	+= ti_k3_r5_remoteproc.o
 obj-$(CONFIG_XLNX_R5_REMOTEPROC)	+= xlnx_r5_remoteproc.o
diff --git a/drivers/remoteproc/ti_k3_m4_remoteproc.c b/drivers/remoteproc/ti_k3_m4_remoteproc.c
new file mode 100644
index 000000000000..9eb313ce0325
--- /dev/null
+++ b/drivers/remoteproc/ti_k3_m4_remoteproc.c
@@ -0,0 +1,327 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * TI K3 Cortex-M4 Remote Processor(s) driver
+ *
+ * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/
+ *	Hari Nagalla <hnagalla@ti.com>
+ */
+
+#include <linux/io.h>
+#include <linux/mailbox_client.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/of_reserved_mem.h>
+#include <linux/omap-mailbox.h>
+#include <linux/platform_device.h>
+#include <linux/remoteproc.h>
+#include <linux/reset.h>
+#include <linux/slab.h>
+
+#include "omap_remoteproc.h"
+#include "remoteproc_internal.h"
+#include "ti_sci_proc.h"
+#include "ti_k3_common.h"
+
+/*
+ * Power up the M4F remote processor.
+ *
+ * This function will be invoked only after the firmware for this rproc
+ * was loaded, parsed successfully, and all of its resource requirements
+ * were met. This callback is invoked only in remoteproc mode.
+ */
+static int k3_m4_rproc_start(struct rproc *rproc)
+{
+	struct k3_rproc *kproc = rproc->priv;
+	u32 boot_addr;
+	int ret;
+
+	ret = k3_rproc_request_mbox(rproc);
+	if (ret)
+		return ret;
+
+	boot_addr = rproc->bootaddr;
+	ret = k3_rproc_release(kproc);
+	if (ret)
+		goto put_mbox;
+
+	return 0;
+
+put_mbox:
+	mbox_free_channel(kproc->mbox);
+	return ret;
+}
+
+/*
+ * Stop the M4 remote processor.
+ *
+ * This function puts the M4 processor into reset, and finishes processing
+ * of any pending messages. This callback is invoked only in remoteproc mode.
+ */
+static int k3_m4_rproc_stop(struct rproc *rproc)
+{
+	struct k3_rproc *kproc = rproc->priv;
+
+	mbox_free_channel(kproc->mbox);
+
+	k3_rproc_reset(kproc);
+
+	return 0;
+}
+
+/*
+ * Attach to a running M4 remote processor (IPC-only mode)
+ *
+ * This rproc attach callback only needs to request the mailbox, the remote
+ * processor is already booted, so there is no need to issue any TI-SCI
+ * commands to boot the M4 core. This callback is used only in IPC-only mode.
+ */
+static int k3_m4_rproc_attach(struct rproc *rproc)
+{
+	struct k3_rproc *kproc = rproc->priv;
+	struct device *dev = kproc->dev;
+	int ret;
+
+	ret = k3_rproc_request_mbox(rproc);
+	if (ret)
+		return ret;
+
+	dev_info(dev, "M4 initialized in IPC-only mode\n");
+	return 0;
+}
+
+/*
+ * Detach from a running M4 remote processor (IPC-only mode)
+ *
+ * This rproc detach callback performs the opposite operation to attach callback
+ * and only needs to release the mailbox, the M4 core is not stopped and will
+ * be left to continue to run its booted firmware. This callback is invoked only in
+ * IPC-only mode.
+ */
+static int k3_m4_rproc_detach(struct rproc *rproc)
+{
+	struct k3_rproc *kproc = rproc->priv;
+	struct device *dev = kproc->dev;
+
+	mbox_free_channel(kproc->mbox);
+	dev_info(dev, "M4 deinitialized in IPC-only mode\n");
+	return 0;
+}
+
+static const struct rproc_ops k3_m4_rproc_ops = {
+	.start		= k3_m4_rproc_start,
+	.stop		= k3_m4_rproc_stop,
+	.attach		= k3_m4_rproc_attach,
+	.detach		= k3_m4_rproc_detach,
+	.kick		= k3_rproc_kick,
+	.da_to_va	= k3_rproc_da_to_va,
+	.get_loaded_rsc_table = k3_get_loaded_rsc_table,
+};
+
+static int k3_m4_rproc_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	const struct k3_rproc_dev_data *data;
+	struct k3_rproc *kproc;
+	struct rproc *rproc;
+	const char *fw_name;
+	bool r_state = false;
+	bool p_state = false;
+	int ret = 0;
+	int ret1;
+
+	data = of_device_get_match_data(dev);
+	if (!data)
+		return -ENODEV;
+
+	ret = rproc_of_parse_firmware(dev, 0, &fw_name);
+	if (ret) {
+		dev_err_probe(dev, ret, "failed to parse firmware-name property\n");
+		return ret;
+	}
+
+	rproc = rproc_alloc(dev, dev_name(dev), &k3_m4_rproc_ops, fw_name,
+			    sizeof(*kproc));
+	if (!rproc)
+		return -ENOMEM;
+
+	rproc->has_iommu = false;
+	rproc->recovery_disabled = true;
+	if (data->uses_lreset) {
+		rproc->ops->prepare = k3_rproc_prepare;
+		rproc->ops->unprepare = k3_rproc_unprepare;
+	}
+	kproc = rproc->priv;
+	kproc->rproc = rproc;
+	kproc->dev = dev;
+	kproc->data = data;
+
+	kproc->ti_sci = ti_sci_get_by_phandle(np, "ti,sci");
+	if (IS_ERR(kproc->ti_sci)) {
+		ret = PTR_ERR(kproc->ti_sci);
+		dev_err_probe(dev, ret, "failed to get ti-sci handle\n");
+		kproc->ti_sci = NULL;
+		goto free_rproc;
+	}
+
+	ret = of_property_read_u32(np, "ti,sci-dev-id", &kproc->ti_sci_id);
+	if (ret) {
+		dev_err_probe(dev, ret, "missing 'ti,sci-dev-id' property\n");
+		goto put_sci;
+	}
+
+	kproc->reset = devm_reset_control_get_exclusive(dev, NULL);
+	if (IS_ERR(kproc->reset)) {
+		ret = PTR_ERR(kproc->reset);
+		dev_err_probe(dev, ret, "failed to get reset\n");
+		goto put_sci;
+	}
+
+	kproc->tsp = k3_rproc_of_get_tsp(dev, kproc->ti_sci);
+	if (IS_ERR(kproc->tsp)) {
+		dev_err_probe(dev, PTR_ERR(kproc->tsp), "failed to construct ti-sci proc control\n");
+		ret = PTR_ERR(kproc->tsp);
+		goto put_sci;
+	}
+
+	ret = ti_sci_proc_request(kproc->tsp);
+	if (ret < 0) {
+		dev_err_probe(dev, ret, "ti_sci_proc_request failed\n");
+		goto free_tsp;
+	}
+
+	ret = k3_rproc_of_get_memories(pdev, kproc);
+	if (ret)
+		goto release_tsp;
+
+	ret = k3_rproc_of_get_sram_memories(pdev, kproc);
+	if (ret)
+		goto release_tsp;
+
+	ret = k3_reserved_mem_init(kproc);
+	if (ret) {
+		dev_err_probe(dev, ret, "reserved memory init failed\n");
+		goto release_tsp;
+	}
+
+	ret = kproc->ti_sci->ops.dev_ops.is_on(kproc->ti_sci, kproc->ti_sci_id,
+					       &r_state, &p_state);
+	if (ret) {
+		dev_err_probe(dev, ret, "failed to get initial state, mode cannot be determined\n");
+		goto release_mem;
+	}
+
+	/* configure devices for either remoteproc or IPC-only mode */
+	if (p_state) {
+		dev_info(dev, "configured M4 for IPC-only mode\n");
+		rproc->state = RPROC_DETACHED;
+		/* override rproc ops with only required IPC-only mode ops */
+		rproc->ops->prepare = NULL;
+		rproc->ops->unprepare = NULL;
+		rproc->ops->start = NULL;
+		rproc->ops->stop = NULL;
+		rproc->ops->attach = k3_m4_rproc_attach;
+		rproc->ops->detach = k3_m4_rproc_detach;
+		rproc->ops->get_loaded_rsc_table = k3_get_loaded_rsc_table;
+	} else {
+		dev_info(dev, "configured M4 for remoteproc mode\n");
+		/*
+		 * ensure the M4 local reset is asserted to ensure the core
+		 * doesn't execute bogus code in .prepare() when the module
+		 * reset is released.
+		 */
+		if (data->uses_lreset) {
+			ret = reset_control_status(kproc->reset);
+			if (ret < 0) {
+				dev_err_probe(dev, ret, "failed to get reset status\n");
+				goto release_mem;
+			} else if (ret == 0) {
+				dev_warn(dev, "local reset is deasserted for device\n");
+				k3_rproc_reset(kproc);
+			}
+		}
+	}
+
+	ret = rproc_add(rproc);
+	if (ret) {
+		dev_err_probe(dev, ret, "failed to add register device with remoteproc core\n");
+		goto release_mem;
+	}
+
+	platform_set_drvdata(pdev, kproc);
+
+	return 0;
+
+release_mem:
+	k3_reserved_mem_exit(kproc);
+release_tsp:
+	ret1 = ti_sci_proc_release(kproc->tsp);
+	if (ret1)
+		dev_err_probe(dev, ret1, "failed to release proc\n");
+free_tsp:
+	kfree(kproc->tsp);
+put_sci:
+	ret1 = ti_sci_put_handle(kproc->ti_sci);
+	if (ret1)
+		dev_err_probe(dev, ret1, "failed to put ti_sci handle\n");
+free_rproc:
+	rproc_free(rproc);
+	return ret;
+}
+
+static int k3_m4_rproc_remove(struct platform_device *pdev)
+{
+	struct k3_rproc *kproc = platform_get_drvdata(pdev);
+	struct device *dev = &pdev->dev;
+	int ret;
+
+	rproc_del(kproc->rproc);
+
+	ret = ti_sci_proc_release(kproc->tsp);
+	if (ret)
+		dev_err(dev, "failed to release proc, ret = %d\n", ret);
+
+	kfree(kproc->tsp);
+
+	ret = ti_sci_put_handle(kproc->ti_sci);
+	if (ret)
+		dev_err(dev, "failed to put ti_sci handle, ret = %d\n", ret);
+
+	k3_reserved_mem_exit(kproc);
+	rproc_free(kproc->rproc);
+
+	return 0;
+}
+
+static const struct k3_rproc_mem_data am64_m4_mems[] = {
+	{ .name = "iram", .dev_addr = 0x0 },
+	{ .name = "dram", .dev_addr = 0x30000 },
+};
+
+static const struct k3_rproc_dev_data am64_m4_data = {
+	.mems = am64_m4_mems,
+	.num_mems = ARRAY_SIZE(am64_m4_mems),
+	.boot_align_addr = SZ_1K,
+	.uses_lreset = true,
+};
+
+static const struct of_device_id k3_m4_of_match[] = {
+	{ .compatible = "ti,am64-m4fss", .data = &am64_m4_data, },
+	{ /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, k3_m4_of_match);
+
+static struct platform_driver k3_m4_rproc_driver = {
+	.probe	= k3_m4_rproc_probe,
+	.remove	= k3_m4_rproc_remove,
+	.driver	= {
+		.name = "k3-m4-rproc",
+		.of_match_table = k3_m4_of_match,
+	},
+};
+
+module_platform_driver(k3_m4_rproc_driver);
+
+MODULE_AUTHOR("Hari Nagalla <hnagalla@ti.com>");
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("TI K3 M4 Remoteproc driver");
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v7 5/5] arm64: defconfig: Enable TI K3 M4 remote proc driver

[Hari Nagalla]

Enable CONFIG_TI_K3_M4_REMOTEPROC

Some K3 platform devices (AM64x, AM62x) have a Cortex M4 core. Build
the M4 remote proc driver as a module for these platforms.

Signed-off-by: Hari Nagalla <hnagalla@ti.com>
---
 arch/arm64/configs/defconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index 2064e7bc529e..c3941821e812 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -1337,6 +1337,7 @@ CONFIG_QCOM_Q6V5_PAS=m
 CONFIG_QCOM_SYSMON=m
 CONFIG_QCOM_WCNSS_PIL=m
 CONFIG_TI_K3_DSP_REMOTEPROC=m
+CONFIG_TI_K3_M4_REMOTEPROC=m
 CONFIG_TI_K3_R5_REMOTEPROC=m
 CONFIG_RPMSG_CHAR=m
 CONFIG_RPMSG_CTRL=m
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel