[PATCH v2 0/4] Add display support for stm32mp135f-dk board

[PATCH v2 0/4] Add display support for stm32mp135f-dk board

[Raphael Gallais-Pou]

This serie aims to enable display support for the stm32mp135f-dk board

Those are only patches of the device-tree since the driver support has
already been added [1].

It respectivelly:
	- adds support for the display controller on stm32mp135
	- adds pinctrl for the display controller
	- enables panel, backlight and display controller on
	  stm32mp135f-dk

Finally it fixes the flags on the panel default mode in the
'panel-simple' driver, allowing to override the default mode by one
described in the device tree, and push further the blanking limit on the
panel.

[1] commit 1726cee3d053 ("drm/stm: ltdc: support of new hardware version")

Changes in v2:
  - Removed already merged patches
https://lore.kernel.org/lkml/170729755552.1647630.4818786052103823648.b4-ty@linaro.org/
https://lore.kernel.org/lkml/170729755662.1647630.425379349649657352.b4-ty@linaro.org/
  - Fixed CHECK_DTBS warnings
  - Added missing properties in panel-simple.yaml

Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
---
Raphael Gallais-Pou (4):
      ARM: dts: stm32: add LTDC support for STM32MP13x SoC family
      ARM: dts: stm32: add LTDC pinctrl on STM32MP13x SoC family
      ARM: dts: stm32: enable display support on stm32mp135f-dk board
      dt-bindings: display: simple: hardware can use several properties

 .../bindings/display/panel/panel-simple.yaml       |  3 ++
 arch/arm/boot/dts/st/stm32mp13-pinctrl.dtsi        | 57 ++++++++++++++++++++++
 arch/arm/boot/dts/st/stm32mp135.dtsi               | 11 +++++
 arch/arm/boot/dts/st/stm32mp135f-dk.dts            | 53 ++++++++++++++++++++
 4 files changed, 124 insertions(+)
---
base-commit: 6613476e225e090cc9aad49be7fa504e290dd33d
change-id: 20240124-ltdc_mp13-2f86a782424c

Best regards,
-- 
Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 1/4] ARM: dts: stm32: add LTDC support for STM32MP13x SoC family

[Raphael Gallais-Pou]

STM32MP13x SoC family embeds a new version of LTDC (Liquid crystal
display - Thin film transistor) Display Controller.

It provides a parallel digital RGB (red, green, blue) and signals for
horizontal, vertical synchronization, pixel clock and data enable as
output to interface directly to a variety of LCD-TFT panels.

Main features
  * 2 input layers blended together to compose the display
  * Cropping of layers from any input size and location
  * Multiple input pixel formats:
    – Predefined ARGB, with 7 formats: ARGB8888, ABGR8888, RGBA8888,
    BGRA8888, RGB565, BGR565, RGB888packed.
    – Flexible ARGB, allowing any width and location for A,R,G,B
    components.
    – Predefined YUV, with 3 formats: YUV422-1L (FourCC: YUYV,
    Interleaved), YUV420-2L (FourCC: NV12, semi planar), YUV420-3L
    (FourCC: Yxx, full planar) with some flexibility on the sequence of
    the component.
  * Color look-up table (CLUT) up to 256 colors (256x24 bits) per layer
  * Color transparency keying
  * Composition with flexible window position and size versus output
  display
  * Blending with flexible layer order and alpha value (per pixel or
  constant)
  * Background underlying color
  * Gamma with non-linear configurable table
  * Dithering for output with less bits per component (pseudo-random on
  2 bits)
  * Polarity inversion for HSync, VSync, and DataEnable outputs
  * Output as RGB888 24 bpp or YUV422 16 bpp
  * Secure layer (using Layer2) capability, with grouped regs and
  additional interrupt set
  * Interrupts based on 7 different events
  * AXI master interface with long efficient bursts (64 or 128 bytes)

Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
Signed-off-by: Yannick Fertre <yannick.fertre@foss.st.com>
---
 arch/arm/boot/dts/st/stm32mp135.dtsi | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/arch/arm/boot/dts/st/stm32mp135.dtsi b/arch/arm/boot/dts/st/stm32mp135.dtsi
index 68d32f9f5314..834a4d545fe4 100644
--- a/arch/arm/boot/dts/st/stm32mp135.dtsi
+++ b/arch/arm/boot/dts/st/stm32mp135.dtsi
@@ -19,5 +19,16 @@ dcmipp: dcmipp@5a000000 {
 			port {
 			};
 		};
+
+		ltdc: display-controller@5a001000 {
+			compatible = "st,stm32-ltdc";
+			reg = <0x5a001000 0x400>;
+			interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc LTDC_PX>;
+			clock-names = "lcd";
+			resets = <&scmi_reset RST_SCMI_LTDC>;
+			status = "disabled";
+		};
 	};
 };

-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 2/4] ARM: dts: stm32: add LTDC pinctrl on STM32MP13x SoC family

[Raphael Gallais-Pou]

Adds LTDC pinctrl support and assigns dedicated GPIO pins.

Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
---
 arch/arm/boot/dts/st/stm32mp13-pinctrl.dtsi | 57 +++++++++++++++++++++++++++++
 1 file changed, 57 insertions(+)

diff --git a/arch/arm/boot/dts/st/stm32mp13-pinctrl.dtsi b/arch/arm/boot/dts/st/stm32mp13-pinctrl.dtsi
index 27e0c3826789..32c5d8a1e06a 100644
--- a/arch/arm/boot/dts/st/stm32mp13-pinctrl.dtsi
+++ b/arch/arm/boot/dts/st/stm32mp13-pinctrl.dtsi
@@ -47,6 +47,63 @@ pins {
 		};
 	};
 
+	ltdc_pins_a: ltdc-0 {
+		pins {
+			pinmux = <STM32_PINMUX('D',  9, AF13)>, /* LCD_CLK */
+				 <STM32_PINMUX('C',  6, AF14)>, /* LCD_HSYNC */
+				 <STM32_PINMUX('G',  4, AF11)>, /* LCD_VSYNC */
+				 <STM32_PINMUX('H',  9, AF11)>, /* LCD_DE */
+				 <STM32_PINMUX('G',  7, AF14)>, /* LCD_R2 */
+				 <STM32_PINMUX('B', 12, AF13)>, /* LCD_R3 */
+				 <STM32_PINMUX('D', 14, AF14)>, /* LCD_R4 */
+				 <STM32_PINMUX('E',  7, AF14)>, /* LCD_R5 */
+				 <STM32_PINMUX('E', 13, AF14)>, /* LCD_R6 */
+				 <STM32_PINMUX('E',  9, AF14)>, /* LCD_R7 */
+				 <STM32_PINMUX('H', 13, AF14)>, /* LCD_G2 */
+				 <STM32_PINMUX('F',  3, AF14)>, /* LCD_G3 */
+				 <STM32_PINMUX('D',  5, AF14)>, /* LCD_G4 */
+				 <STM32_PINMUX('G',  0, AF14)>, /* LCD_G5 */
+				 <STM32_PINMUX('C',  7, AF14)>, /* LCD_G6 */
+				 <STM32_PINMUX('A', 15, AF11)>, /* LCD_G7 */
+				 <STM32_PINMUX('D', 10, AF14)>, /* LCD_B2 */
+				 <STM32_PINMUX('F',  2, AF14)>, /* LCD_B3 */
+				 <STM32_PINMUX('H', 14, AF11)>, /* LCD_B4 */
+				 <STM32_PINMUX('E',  0, AF14)>, /* LCD_B5 */
+				 <STM32_PINMUX('B',  6, AF7)>,  /* LCD_B6 */
+				 <STM32_PINMUX('F',  1, AF13)>; /* LCD_B7 */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	ltdc_sleep_pins_a: ltdc-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('D',  9, ANALOG)>, /* LCD_CLK */
+				 <STM32_PINMUX('C',  6, ANALOG)>, /* LCD_HSYNC */
+				 <STM32_PINMUX('G',  4, ANALOG)>, /* LCD_VSYNC */
+				 <STM32_PINMUX('H',  9, ANALOG)>, /* LCD_DE */
+				 <STM32_PINMUX('G',  7, ANALOG)>, /* LCD_R2 */
+				 <STM32_PINMUX('B', 12, ANALOG)>, /* LCD_R3 */
+				 <STM32_PINMUX('D', 14, ANALOG)>, /* LCD_R4 */
+				 <STM32_PINMUX('E',  7, ANALOG)>, /* LCD_R5 */
+				 <STM32_PINMUX('E', 13, ANALOG)>, /* LCD_R6 */
+				 <STM32_PINMUX('E',  9, ANALOG)>, /* LCD_R7 */
+				 <STM32_PINMUX('H', 13, ANALOG)>, /* LCD_G2 */
+				 <STM32_PINMUX('F',  3, ANALOG)>, /* LCD_G3 */
+				 <STM32_PINMUX('D',  5, ANALOG)>, /* LCD_G4 */
+				 <STM32_PINMUX('G',  0, ANALOG)>, /* LCD_G5 */
+				 <STM32_PINMUX('C',  7, ANALOG)>, /* LCD_G6 */
+				 <STM32_PINMUX('A', 15, ANALOG)>, /* LCD_G7 */
+				 <STM32_PINMUX('D', 10, ANALOG)>, /* LCD_B2 */
+				 <STM32_PINMUX('F',  2, ANALOG)>, /* LCD_B3 */
+				 <STM32_PINMUX('H', 14, ANALOG)>, /* LCD_B4 */
+				 <STM32_PINMUX('E',  0, ANALOG)>, /* LCD_B5 */
+				 <STM32_PINMUX('B',  6, ANALOG)>, /* LCD_B6 */
+				 <STM32_PINMUX('F',  1, ANALOG)>; /* LCD_B7 */
+		};
+	};
+
 	mcp23017_pins_a: mcp23017-0 {
 		pins {
 			pinmux = <STM32_PINMUX('G', 12, GPIO)>;

-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 3/4] ARM: dts: stm32: enable display support on stm32mp135f-dk board

[Raphael Gallais-Pou]

Link panel and display controller.
Enable panel, backlight and display controller.

Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>

---
Changes in v2:
  - Fixed dtbs_check warnings :
arch/arm/boot/dts/st/stm32mp135f-dk.dtb: panel-backlight: 'default-brightness-level' does not match any of the regexes: 'pinctrl-[0-9]+'
  from schema $id: http://devicetree.org/schemas/leds/backlight/gpio-backlight.yaml#
arch/arm/boot/dts/st/stm32mp135f-dk.dtb: panel-rgb: data-mapping:0: 'bgr666' is not one of ['jeida-18', 'jeida-24', 'vesa-24']
  from schema $id: http://devicetree.org/schemas/display/panel/panel-simple.yaml#
arch/arm/boot/dts/st/stm32mp135f-dk.dtb: panel-rgb: compatible: ['rocktech,rk043fn48h', 'panel-dpi'] is too long
  from schema $id: http://devicetree.org/schemas/display/panel/panel-simple.yaml#
arch/arm/boot/dts/st/stm32mp135f-dk.dtb: panel-rgb: data-mapping: False schema does not allow ['bgr666']
  from schema $id: http://devicetree.org/schemas/display/panel/panel-simple.yaml#
---
 arch/arm/boot/dts/st/stm32mp135f-dk.dts | 53 +++++++++++++++++++++++++++++++++
 1 file changed, 53 insertions(+)

diff --git a/arch/arm/boot/dts/st/stm32mp135f-dk.dts b/arch/arm/boot/dts/st/stm32mp135f-dk.dts
index eea740d097c7..c918f332cbfd 100644
--- a/arch/arm/boot/dts/st/stm32mp135f-dk.dts
+++ b/arch/arm/boot/dts/st/stm32mp135f-dk.dts
@@ -66,6 +66,46 @@ led-blue {
 			default-state = "off";
 		};
 	};
+
+	panel_backlight: panel-backlight {
+		compatible = "gpio-backlight";
+		gpios = <&gpioe 12 GPIO_ACTIVE_HIGH>;
+		default-on;
+		status = "okay";
+	};
+
+	panel_rgb: panel-rgb {
+		compatible = "rocktech,rk043fn48h";
+		enable-gpios = <&gpioi 7 GPIO_ACTIVE_HIGH>;
+		backlight = <&panel_backlight>;
+		power-supply = <&scmi_v3v3_sw>;
+		status = "okay";
+
+		width-mm = <105>;
+		height-mm = <67>;
+
+		panel-timing {
+			clock-frequency = <10000000>;
+			hactive = <480>;
+			hback-porch = <43>;
+			hfront-porch = <10>;
+			hsync-len = <1>;
+			hsync-active = <0>;
+			vactive = <272>;
+			vback-porch = <26>;
+			vfront-porch = <4>;
+			vsync-len = <10>;
+			vsync-active = <0>;
+			de-active = <1>;
+			pixelclk-active = <1>;
+		};
+
+		port {
+			panel_in_rgb: endpoint {
+				remote-endpoint = <&ltdc_out_rgb>;
+			};
+		};
+	};
 };
 
 &adc_1 {
@@ -160,6 +200,19 @@ &iwdg2 {
 	status = "okay";
 };
 
+&ltdc {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&ltdc_pins_a>;
+	pinctrl-1 = <&ltdc_sleep_pins_a>;
+	status = "okay";
+
+	port {
+		ltdc_out_rgb: endpoint {
+			remote-endpoint = <&panel_in_rgb>;
+		};
+	};
+};
+
 &rtc {
 	status = "okay";
 };

-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 4/4] dt-bindings: display: simple: hardware can use several properties

[Raphael Gallais-Pou]

Setting a panel-timing in the device-tree overwrite the one specified in
the driver and set it as preferred.  In that case 'height-mm',
'width-mm' and 'panel-timing' are properties that can be use for simple
panels, according to panel-common.yaml

Fixes following warnings:
arch/arm/boot/dts/st/stm32mp135f-dk.dtb: panel-rgb: 'height-mm', 'panel-timing', 'width-mm' do not match any of the regexes: 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/display/panel/panel-simple.yaml#

Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
---
 Documentation/devicetree/bindings/display/panel/panel-simple.yaml | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
index 634a10c6f2dd..c02cbbc7a100 100644
--- a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
+++ b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
@@ -352,6 +352,9 @@ properties:
   no-hpd: true
   hpd-gpios: true
   data-mapping: true
+  height-mm: true
+  width-mm: true
+  panel-timing: true
 
 if:
   not:

-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v2 4/4] dt-bindings: display: simple: hardware can use several properties

[Rob Herring]

On Sat, Feb 17, 2024 at 12:02:58PM +0100, Raphael Gallais-Pou wrote:
> Setting a panel-timing in the device-tree overwrite the one specified in
> the driver and set it as preferred.  In that case 'height-mm',
> 'width-mm' and 'panel-timing' are properties that can be use for simple
> panels, according to panel-common.yaml
> 
> Fixes following warnings:
> arch/arm/boot/dts/st/stm32mp135f-dk.dtb: panel-rgb: 'height-mm', 'panel-timing', 'width-mm' do not match any of the regexes: 'pinctrl-[0-9]+'
> 	from schema $id: http://devicetree.org/schemas/display/panel/panel-simple.yaml#
> 
> Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
> ---
>  Documentation/devicetree/bindings/display/panel/panel-simple.yaml | 3 +++
>  1 file changed, 3 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
> index 634a10c6f2dd..c02cbbc7a100 100644
> --- a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
> +++ b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
> @@ -352,6 +352,9 @@ properties:
>    no-hpd: true
>    hpd-gpios: true
>    data-mapping: true
> +  height-mm: true
> +  width-mm: true
> +  panel-timing: true

Instead, just change 'additionalProperties' to 'unevaluateProperties' 
and drop all these 'prop: true' lines. Pretty much anything from 
panel-common.yaml should be allowed.

Rob

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v2 4/4] dt-bindings: display: simple: hardware can use several properties

[Raphael Gallais-Pou]

On 2/23/24 01:09, Rob Herring wrote:
> On Sat, Feb 17, 2024 at 12:02:58PM +0100, Raphael Gallais-Pou wrote:
>> Setting a panel-timing in the device-tree overwrite the one specified in
>> the driver and set it as preferred.  In that case 'height-mm',
>> 'width-mm' and 'panel-timing' are properties that can be use for simple
>> panels, according to panel-common.yaml
>>
>> Fixes following warnings:
>> arch/arm/boot/dts/st/stm32mp135f-dk.dtb: panel-rgb: 'height-mm', 'panel-timing', 'width-mm' do not match any of the regexes: 'pinctrl-[0-9]+'
>> 	from schema $id: http://devicetree.org/schemas/display/panel/panel-simple.yaml#
>>
>> Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
>> ---
>>  Documentation/devicetree/bindings/display/panel/panel-simple.yaml | 3 +++
>>  1 file changed, 3 insertions(+)
>>
>> diff --git a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
>> index 634a10c6f2dd..c02cbbc7a100 100644
>> --- a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
>> +++ b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
>> @@ -352,6 +352,9 @@ properties:
>>    no-hpd: true
>>    hpd-gpios: true
>>    data-mapping: true
>> +  height-mm: true
>> +  width-mm: true
>> +  panel-timing: true
Hi Rob,
> Instead, just change 'additionalProperties' to 'unevaluateProperties' 
> and drop all these 'prop: true' lines. Pretty much anything from 
> panel-common.yaml should be allowed.


Will do, thanks :)


Best regards,

Raphaël

>
> Rob

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel