Re: [PATCH 1/5] dt-bindings: iio: dac: ti,dac5571: Add DAC081C081 support

From: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
To: Jonathan Cameron <jic23@kernel.org>
Cc: devicetree@vger.kernel.org, imx@lists.linux.dev,
	linux-arm-kernel@lists.infradead.org,
	Trevor Zaharichuk <trevor@au-zone.com>,
	Greg Lytle <greg@au-zone.com>,
	Lars-Peter Clausen <lars@metafoo.de>,
	Rob Herring <robh@kernel.org>,
	Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
	Conor Dooley <conor+dt@kernel.org>,
	Sean Nyekjaer <sean@geanix.com>,
	linux-iio@vger.kernel.org
Subject: Re: [PATCH 1/5] dt-bindings: iio: dac: ti,dac5571: Add DAC081C081 support
Date: Mon, 25 Mar 2024 22:56:41 +0200	[thread overview]
Message-ID: <20240325205641.GD23988@pendragon.ideasonboard.com> (raw)
In-Reply-To: <20240325204857.4f2fd468@jic23-huawei>

Hi Jonathan,

On Mon, Mar 25, 2024 at 08:48:57PM +0000, Jonathan Cameron wrote:
> On Mon, 25 Mar 2024 22:32:41 +0200 Laurent Pinchart wrote:
> 
> > The DAC081C081 is a TI DAC whose software interface is compatible with
> > the DAC5571. It is the 8-bit version of the DAC121C081, already
> > supported by the DAC5571 bindings. Extends the bindings to support this
> > chip.
> > 
> > Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> 
> Hi Laurent,
> 
> Given it's a part number where no one is going to guess it is compatible
> with the DAC5571 and that we don't have a history of fallback compatibles
> I'm fine with this change, but just wanted to ask is a fallback compatible
> useful to you to run with older kernels?
> 
> I should have noticed when Peter added the dac121c081. If we add a fallback
> should do that one as well.

I've indeed noticed that there should have been a fallback for
dac121c081, but didn't stop to ponder why that wasn't the case, and just
went along with the flow :-) I agree a fallback could be useful, which
would then allow dropping patch 2/5 from this series (*). I can do so if
you prefer.

* This is not entirely true. While the DAC1081C081 is largely compatible
with the DAC5573, they have different values for one of the power-down
resistors (2.5kΩ instead of 1kΩ if I recall correctly). To be completely
accurate, the driver should report that. We could still use the fallback
compatible, reporting the wrong power-down resistor value.

> > ---
> >  Documentation/devicetree/bindings/iio/dac/ti,dac5571.yaml | 1 +
> >  1 file changed, 1 insertion(+)
> > 
> > diff --git a/Documentation/devicetree/bindings/iio/dac/ti,dac5571.yaml b/Documentation/devicetree/bindings/iio/dac/ti,dac5571.yaml
> > index 79da0323c327..e59db861e2eb 100644
> > --- a/Documentation/devicetree/bindings/iio/dac/ti,dac5571.yaml
> > +++ b/Documentation/devicetree/bindings/iio/dac/ti,dac5571.yaml
> > @@ -21,6 +21,7 @@ properties:
> >        - ti,dac5573
> >        - ti,dac6573
> >        - ti,dac7573
> > +      - ti,dac081c081
> >        - ti,dac121c081
> >  
> >    reg:

-- 
Regards,

Laurent Pinchart

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel