Linux-ARM-Kernel Archive on lore.kernel.org
 help / color / mirror / Atom feed
From: Frank Li <Frank.Li@nxp.com>
To: Rob Herring <robh@kernel.org>,
	Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
	Conor Dooley <conor+dt@kernel.org>,
	Shawn Guo <shawnguo@kernel.org>,
	Sascha Hauer <s.hauer@pengutronix.de>,
	Pengutronix Kernel Team <kernel@pengutronix.de>,
	Fabio Estevam <festevam@gmail.com>,
	devicetree@vger.kernel.org (open list:OPEN FIRMWARE AND
	FLATTENED DEVICE TREE BINDINGS),
	imx@lists.linux.dev (open list:ARM/FREESCALE IMX / MXC ARM
	ARCHITECTURE),
	linux-arm-kernel@lists.infradead.org (moderated
	list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE),
	linux-kernel@vger.kernel.org (open list)
Subject: [PATCH 1/1] arm64: dts: imx8qxp-mek: add cm40_i2c, wm8960/wm8962 and sai[0,1,4,5]
Date: Thu,  4 Apr 2024 12:19:13 -0400	[thread overview]
Message-ID: <20240404161914.1655305-1-Frank.Li@nxp.com> (raw)

imx8qxp-mek use two kind audio codec, wm8960 and wm8962. Using dummy gpio
i2c bus mux to connect both i2c devices. One will probe failure and other
will probe success when devices driver check whoami. So one dtb can cover
both board configuration.

Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
 arch/arm64/boot/dts/freescale/imx8qxp-mek.dts | 210 ++++++++++++++++++
 1 file changed, 210 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx8qxp-mek.dts b/arch/arm64/boot/dts/freescale/imx8qxp-mek.dts
index 8360bb851ac03..adff87c7cf305 100644
--- a/arch/arm64/boot/dts/freescale/imx8qxp-mek.dts
+++ b/arch/arm64/boot/dts/freescale/imx8qxp-mek.dts
@@ -30,6 +30,13 @@ reg_usdhc2_vmmc: usdhc2-vmmc {
 		enable-active-high;
 	};
 
+	reg_audio: regulator-wm8962 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3_aud";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
 	gpio-sbu-mux {
 		compatible = "nxp,cbdtu02043", "gpio-sbu-mux";
 		pinctrl-names = "default";
@@ -44,6 +51,105 @@ usb3_data_ss: endpoint {
 			};
 		};
 	};
+
+	sound-wm8960 {
+		compatible = "fsl,imx-audio-wm8960";
+		model = "wm8960-audio";
+		audio-cpu = <&sai1>;
+		audio-codec = <&wm8960>;
+		hp-det-gpio = <&lsio_gpio1 0 GPIO_ACTIVE_HIGH>;
+		audio-routing =
+			"Headphone Jack", "HP_L",
+			"Headphone Jack", "HP_R",
+			"Ext Spk", "SPK_LP",
+			"Ext Spk", "SPK_LN",
+			"Ext Spk", "SPK_RP",
+			"Ext Spk", "SPK_RN",
+			"LINPUT1", "Mic Jack",
+			"Mic Jack", "MICB";
+	};
+
+	sound-wm8962 {
+		compatible = "fsl,imx-audio-wm8962";
+		model = "wm8962-audio";
+		audio-cpu = <&sai1>;
+		audio-codec = <&wm8962>;
+		hp-det-gpio = <&lsio_gpio1 0 GPIO_ACTIVE_HIGH>;
+		audio-routing =
+			"Headphone Jack", "HPOUTL",
+			"Headphone Jack", "HPOUTR",
+			"Ext Spk", "SPKOUTL",
+			"Ext Spk", "SPKOUTR",
+			"AMIC", "MICBIAS",
+			"IN3R", "AMIC",
+			"IN1R", "AMIC";
+	};
+
+	/*
+	 * This dummy i2c mux. GPIO actually will not impact selection. At actual boards, only 1
+	 * device connectted. I2C client driver will check ID when probe. Only matched ID's driver
+	 * probe successfully.
+	 */
+	i2cvmux: i2cmux {
+		compatible = "i2c-mux-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		mux-gpios = <&lsio_gpio5 0 GPIO_ACTIVE_HIGH>; /* use an unused gpio */
+		i2c-parent = <&cm40_i2c>;
+
+		i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			/* WCPU boards SCH-54536 */
+			wm8962: wm8962@1a {
+				compatible = "wlf,wm8962";
+				reg = <0x1a>;
+				clocks = <&mclkout0_lpcg IMX_LPCG_CLK_0>;
+				assigned-clocks = <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_PLL>,
+						  <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_SLV_BUS>,
+						  <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_MST_BUS>,
+						  <&mclkout0_lpcg IMX_LPCG_CLK_0>;
+				assigned-clock-rates = <786432000>,
+						       <49152000>,
+						       <12288000>,
+						       <12288000>;
+				DCVDD-supply = <&reg_audio>;
+				DBVDD-supply = <&reg_audio>;
+				AVDD-supply = <&reg_audio>;
+				CPVDD-supply = <&reg_audio>;
+				MICVDD-supply = <&reg_audio>;
+				PLLVDD-supply = <&reg_audio>;
+				SPKVDD1-supply = <&reg_audio>;
+				SPKVDD2-supply = <&reg_audio>;
+			};
+		};
+
+		i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			wm8960: wm8960@1a {
+				compatible = "wlf,wm8960";
+				reg = <0x1a>;
+				clocks = <&mclkout0_lpcg IMX_LPCG_CLK_0>;
+				clock-names = "mclk";
+				wlf,shared-lrclk;
+				wlf,hp-cfg = <2 2 3>;
+				wlf,gpio-cfg = <1 3>;
+				assigned-clocks = <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_PLL>,
+						  <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_SLV_BUS>,
+						  <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_MST_BUS>,
+						  <&mclkout0_lpcg IMX_LPCG_CLK_0>;
+				assigned-clock-rates = <786432000>,
+						       <49152000>,
+						       <12288000>,
+						       <12288000>;
+			};
+		};
+	};
 };
 
 &dsp {
@@ -188,6 +294,29 @@ typec_con_ss: endpoint {
 
 };
 
+&cm40_i2c {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_cm40_i2c>;
+	pinctrl-1 = <&pinctrl_cm40_i2c_gpio>;
+	scl-gpios = <&lsio_gpio1 10 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&lsio_gpio1 9 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+
+	pca6416: gpio@20 {
+		compatible = "ti,tca6416";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+};
+
+&cm40_intmux {
+	status = "okay";
+};
+
 &lpuart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_lpuart0>;
@@ -218,6 +347,53 @@ &scu_key {
 	status = "okay";
 };
 
+&sai0 {
+	#sound-dai-cells = <0>;
+	assigned-clocks = <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_PLL>,
+			  <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_SLV_BUS>,
+			  <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_MST_BUS>,
+			  <&sai0_lpcg IMX_LPCG_CLK_0>;
+	assigned-clock-rates = <786432000>, <49152000>, <12288000>, <49152000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai0>;
+	status = "okay";
+};
+
+&sai1 {
+	assigned-clocks = <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_PLL>,
+			  <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_SLV_BUS>,
+			  <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_MST_BUS>,
+			  <&sai1_lpcg IMX_LPCG_CLK_0>;
+	assigned-clock-rates = <786432000>, <49152000>, <12288000>, <49152000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai1>;
+	status = "okay";
+};
+
+&sai4 {
+	assigned-clocks = <&acm IMX_ADMA_ACM_SAI4_MCLK_SEL>,
+			  <&clk IMX_SC_R_AUDIO_PLL_1 IMX_SC_PM_CLK_PLL>,
+			  <&clk IMX_SC_R_AUDIO_PLL_1 IMX_SC_PM_CLK_SLV_BUS>,
+			  <&clk IMX_SC_R_AUDIO_PLL_1 IMX_SC_PM_CLK_MST_BUS>,
+			  <&sai4_lpcg IMX_LPCG_CLK_0>;
+	assigned-clock-parents = <&aud_pll_div1_lpcg IMX_LPCG_CLK_0>;
+	assigned-clock-rates = <0>, <786432000>, <98304000>, <12288000>, <98304000>;
+	fsl,sai-asynchronous;
+	status = "okay";
+};
+
+&sai5 {
+	assigned-clocks = <&acm IMX_ADMA_ACM_SAI5_MCLK_SEL>,
+			  <&clk IMX_SC_R_AUDIO_PLL_1 IMX_SC_PM_CLK_PLL>,
+			  <&clk IMX_SC_R_AUDIO_PLL_1 IMX_SC_PM_CLK_SLV_BUS>,
+			  <&clk IMX_SC_R_AUDIO_PLL_1 IMX_SC_PM_CLK_MST_BUS>,
+			  <&sai5_lpcg IMX_LPCG_CLK_0>;
+	assigned-clock-parents = <&aud_pll_div1_lpcg IMX_LPCG_CLK_0>;
+	assigned-clock-rates = <0>, <786432000>, <98304000>, <12288000>, <98304000>;
+	fsl,sai-asynchronous;
+	status = "okay";
+};
+
 &thermal_zones {
 	pmic-thermal {
 		polling-delay-passive = <250>;
@@ -314,6 +490,21 @@ &vpu_core1 {
 };
 
 &iomuxc {
+
+	pinctrl_cm40_i2c: cm40i2cgrp {
+		fsl,pins = <
+			IMX8QXP_ADC_IN1_M40_I2C0_SDA                            0x0600004c
+			IMX8QXP_ADC_IN0_M40_I2C0_SCL                            0x0600004c
+		>;
+	};
+
+	pinctrl_cm40_i2c_gpio: cm40i2cgpio-grp {
+		fsl,pins = <
+			IMX8QXP_ADC_IN1_LSIO_GPIO1_IO09				0xc600004c
+			IMX8QXP_ADC_IN0_LSIO_GPIO1_IO10				0xc600004c
+		>;
+	};
+
 	pinctrl_fec1: fec1grp {
 		fsl,pins = <
 			IMX8QXP_ENET0_MDC_CONN_ENET0_MDC			0x06000020
@@ -385,6 +576,25 @@ IMX8QXP_ENET0_REFCLK_125M_25M_LSIO_GPIO5_IO09           0x60
 		>;
 	};
 
+	pinctrl_sai0: sai0grp {
+		fsl,pins = <
+			IMX8QXP_SAI0_TXD_ADMA_SAI0_TXD		0x06000060
+			IMX8QXP_SAI0_RXD_ADMA_SAI0_RXD		0x06000040
+			IMX8QXP_SAI0_TXC_ADMA_SAI0_TXC		0x06000040
+			IMX8QXP_SAI0_TXFS_ADMA_SAI0_TXFS	0x06000040
+		>;
+	};
+
+	pinctrl_sai1: sai1grp {
+		fsl,pins = <
+			IMX8QXP_SAI1_RXD_ADMA_SAI1_RXD     0x06000040
+			IMX8QXP_SAI1_RXC_ADMA_SAI1_TXC     0x06000040
+			IMX8QXP_SAI1_RXFS_ADMA_SAI1_TXFS   0x06000040
+			IMX8QXP_SPI0_CS1_ADMA_SAI1_TXD     0x06000060
+			IMX8QXP_SPI2_CS0_LSIO_GPIO1_IO00   0x06000040
+		>;
+	};
+
 	pinctrl_usdhc1: usdhc1grp {
 		fsl,pins = <
 			IMX8QXP_EMMC0_CLK_CONN_EMMC0_CLK			0x06000041
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

             reply	other threads:[~2024-04-04 16:20 UTC|newest]

Thread overview: 9+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2024-04-04 16:19 Frank Li [this message]
2024-04-05  6:36 ` [PATCH 1/1] arm64: dts: imx8qxp-mek: add cm40_i2c, wm8960/wm8962 and sai[0,1,4,5] Francesco Dolcini
2024-04-05 14:56   ` Frank Li
2024-04-05  6:41 ` Krzysztof Kozlowski
2024-04-05 14:46   ` Frank Li
2024-04-05 18:21     ` Krzysztof Kozlowski
2024-04-08 15:36       ` Frank Li
2024-04-09  6:33         ` Krzysztof Kozlowski
2024-04-09 16:02           ` Frank Li

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20240404161914.1655305-1-Frank.Li@nxp.com \
    --to=frank.li@nxp.com \
    --cc=conor+dt@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=festevam@gmail.com \
    --cc=imx@lists.linux.dev \
    --cc=kernel@pengutronix.de \
    --cc=krzysztof.kozlowski+dt@linaro.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=robh@kernel.org \
    --cc=s.hauer@pengutronix.de \
    --cc=shawnguo@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox