* [PATCH v4 0/4] arm64: dts: add description for solidrun cn9130 som and clearfog boards
@ 2024-05-02 12:32 Josua Mayer
2024-05-02 12:32 ` [PATCH v4 1/4] dt-bindings: arm64: marvell: add solidrun cn9130 som based boards Josua Mayer
` (4 more replies)
0 siblings, 5 replies; 11+ messages in thread
From: Josua Mayer @ 2024-05-02 12:32 UTC (permalink / raw)
To: Andrew Lunn, Gregory Clement, Sebastian Hesselbarth, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Rob Herring
Cc: Yazan Shhady, linux-arm-kernel, devicetree, linux-kernel,
Josua Mayer, Krzysztof Kozlowski
SolidRun CN9130 SoM is a mostly pin-comptible replacement for Armada 388
SoM used in Clearfog and Clearfog Pro boards.
1. Add new binding for compatible strings closely matching the original.
2. Add device-tree includes for SoM and carrier shared design.
3. Add device-tree for both Clearfog Base and Pro.
While dtbs_check is happy with LED descriptions behind dsa switch,
functionally they require supporting code by Andrew Lunn:
https://lore.kernel.org/r/20240401-v6-8-0-net-next-mv88e6xxx-leds-v4-v3-0-221b3fa55f78@lunn.ch
NOTICE IN CASE ANYBODY WANTS TO SELF-UPGRADE:
CN9130 SoM has a different footprint from Armada 388 SoM.
Components on the carrier board below the SoM may collide causing
damage, such as on Clearfog Base.
Signed-off-by: Josua Mayer <josua@solid-run.com>
---
Changes in v4:
- Picked up reviewed-by tags by Andrew Lunn.
- fixed a typo and changed 3-line comment into single-line comment
for clearfog-base/-pro dts, but kept review tags since change was
minor.
- Updated SFP led labels to use "sfp?:colour" without "color" property,
to avoid duplicate labels while reflecting they are each dual-colour.
- Link to v3: https://lore.kernel.org/r/20240414-cn9130-som-v3-0-350a67d44e0a@solid-run.com
Changes in v3:
- picked up acked-by for dt-bindings
- skipped acked-by for dts because additional changes were made:
- moved legacy netdev aliases to carrier dts
- fix status property style errors
- add pinctrl for secondary spi chip-select on mikrobus header (& som)
- specify spi bus frequency limits for som
- Added CN9131 SolidWAN board
- Link to v2: https://lore.kernel.org/r/20240404-cn9130-som-v2-0-3af2229c7d2d@solid-run.com
Changes in v2:
- rewrote dt bindings dropping unnecessary compatibles
(Reported-By: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>)
- added bindings for two additional boards (cn9131/9132)
support planned for the coming weeks, mostly serves
illustrational purposes, to understand cn913x variants
- cf-pro: add description for LEDs behind DSA switch
- cf-base: add description for LEDs behind PHYs
(Reported-By: Andrew Lunn <andrew@lunn.ch>)
- Link to v1: https://lore.kernel.org/r/20240321-cn9130-som-v1-0-711127a409ae@solid-run.com
---
Josua Mayer (4):
dt-bindings: arm64: marvell: add solidrun cn9130 som based boards
dt-bindings: arm64: marvell: add solidrun cn9132 CEX-7 evaluation board
arm64: dts: add description for solidrun cn9130 som and clearfog boards
arm64: dts: add description for solidrun cn9131 solidwan board
.../bindings/arm/marvell/armada-7k-8k.yaml | 18 +
arch/arm64/boot/dts/marvell/Makefile | 3 +
arch/arm64/boot/dts/marvell/cn9130-cf-base.dts | 178 ++++++
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dts | 375 ++++++++++++
arch/arm64/boot/dts/marvell/cn9130-cf.dtsi | 197 +++++++
arch/arm64/boot/dts/marvell/cn9130-sr-som.dtsi | 160 +++++
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dts | 643 +++++++++++++++++++++
7 files changed, 1574 insertions(+)
---
base-commit: 4cece764965020c22cff7665b18a012006359095
change-id: 20240318-cn9130-som-848e86acb0ac
Sincerely,
--
Josua Mayer <josua@solid-run.com>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 11+ messages in thread
* [PATCH v4 1/4] dt-bindings: arm64: marvell: add solidrun cn9130 som based boards
2024-05-02 12:32 [PATCH v4 0/4] arm64: dts: add description for solidrun cn9130 som and clearfog boards Josua Mayer
@ 2024-05-02 12:32 ` Josua Mayer
2024-05-02 12:32 ` [PATCH v4 2/4] dt-bindings: arm64: marvell: add solidrun cn9132 CEX-7 evaluation board Josua Mayer
` (3 subsequent siblings)
4 siblings, 0 replies; 11+ messages in thread
From: Josua Mayer @ 2024-05-02 12:32 UTC (permalink / raw)
To: Andrew Lunn, Gregory Clement, Sebastian Hesselbarth, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Rob Herring
Cc: Yazan Shhady, linux-arm-kernel, devicetree, linux-kernel,
Josua Mayer, Krzysztof Kozlowski
Add bindings for SolidRun boards based on CN9130 SoM.
Three boards are added in total:
- Clearfog Base
- Clearfog Pro
- SolidWAN
The Clearfog boards are identical to the older Armada 388 based boards,
upgraded with a new SoM and SoC.
However the feature set and performance characteristics are different,
therefore compatible strings from armada 388 versions are not included.
SolidWAN uses the same SoM adding a southbridge on the carrier.
Since 2019 there are bindings in-tree for two boards based on cn9130 and
9131. These are extremely verbose by listing cn9132, cn9131, cn9130,
ap807-quad, ap807 for the SoC alone.
CN9130 SoC combines an application processor (ap807) and a
communication processor (cp115) in a single package.
The communication processor (short CP) is also available separately as a
southbridge. It only functions in combination with the CN9130 SoC.
Complete systems adding one or two southbridges are by convention called
CN9131 and CN9132 respectively.
Despite different naming all systems are built around the same SoC.
Therefore marvell,cn9131 and marvell,cn9132 can be omitted. The number
of CPs is part of a board's BoM and can be reflected in the board
compatible string instead.
Existing bindings also describe cn9130 as a specialisation of
ap807-quad. Usually board-level compatibles stop at the SoC without
going into silicon versions or individual dies.
There is no programming model at this layer, and in particular not for
parts of an SoC. Therefore the ap compatibles can also be omitted.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---
.../devicetree/bindings/arm/marvell/armada-7k-8k.yaml | 10 ++++++++++
1 file changed, 10 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.yaml b/Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.yaml
index 16d2e132d3d1..74d935ea279c 100644
--- a/Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.yaml
+++ b/Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.yaml
@@ -82,4 +82,14 @@ properties:
- const: marvell,armada-ap807-quad
- const: marvell,armada-ap807
+ - description:
+ SolidRun CN9130 SoM based single-board computers
+ items:
+ - enum:
+ - solidrun,cn9130-clearfog-base
+ - solidrun,cn9130-clearfog-pro
+ - solidrun,cn9131-solidwan
+ - const: solidrun,cn9130-sr-som
+ - const: marvell,cn9130
+
additionalProperties: true
--
2.35.3
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH v4 2/4] dt-bindings: arm64: marvell: add solidrun cn9132 CEX-7 evaluation board
2024-05-02 12:32 [PATCH v4 0/4] arm64: dts: add description for solidrun cn9130 som and clearfog boards Josua Mayer
2024-05-02 12:32 ` [PATCH v4 1/4] dt-bindings: arm64: marvell: add solidrun cn9130 som based boards Josua Mayer
@ 2024-05-02 12:32 ` Josua Mayer
2024-05-02 12:32 ` [PATCH v4 3/4] arm64: dts: add description for solidrun cn9130 som and clearfog boards Josua Mayer
` (2 subsequent siblings)
4 siblings, 0 replies; 11+ messages in thread
From: Josua Mayer @ 2024-05-02 12:32 UTC (permalink / raw)
To: Andrew Lunn, Gregory Clement, Sebastian Hesselbarth, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Rob Herring
Cc: Yazan Shhady, linux-arm-kernel, devicetree, linux-kernel,
Josua Mayer, Krzysztof Kozlowski
Add bindings for the SolidRun CN9132 COM-Express Type 7 evaluation board.
The CEX is based on CN9130 SoC and includes two southbridges.
Because CN9132 and 9131 are just names for different designs around the
same SoC, no soc compatibles beside marvell,cn9130 are needed.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---
Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.yaml | 8 ++++++++
1 file changed, 8 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.yaml b/Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.yaml
index 74d935ea279c..538d91be8857 100644
--- a/Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.yaml
+++ b/Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.yaml
@@ -92,4 +92,12 @@ properties:
- const: solidrun,cn9130-sr-som
- const: marvell,cn9130
+ - description:
+ SolidRun CN9132 COM-Express Type 7 based single-board computers
+ items:
+ - enum:
+ - solidrun,cn9132-clearfog
+ - const: solidrun,cn9132-sr-cex7
+ - const: marvell,cn9130
+
additionalProperties: true
--
2.35.3
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH v4 3/4] arm64: dts: add description for solidrun cn9130 som and clearfog boards
2024-05-02 12:32 [PATCH v4 0/4] arm64: dts: add description for solidrun cn9130 som and clearfog boards Josua Mayer
2024-05-02 12:32 ` [PATCH v4 1/4] dt-bindings: arm64: marvell: add solidrun cn9130 som based boards Josua Mayer
2024-05-02 12:32 ` [PATCH v4 2/4] dt-bindings: arm64: marvell: add solidrun cn9132 CEX-7 evaluation board Josua Mayer
@ 2024-05-02 12:32 ` Josua Mayer
2024-05-02 12:32 ` [PATCH v4 4/4] arm64: dts: add description for solidrun cn9131 solidwan board Josua Mayer
2024-05-02 15:08 ` [PATCH v4 0/4] arm64: dts: add description for solidrun cn9130 som and clearfog boards Rob Herring (Arm)
4 siblings, 0 replies; 11+ messages in thread
From: Josua Mayer @ 2024-05-02 12:32 UTC (permalink / raw)
To: Andrew Lunn, Gregory Clement, Sebastian Hesselbarth, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Rob Herring
Cc: Yazan Shhady, linux-arm-kernel, devicetree, linux-kernel,
Josua Mayer
Add description for the SolidRun CN9130 SoM, and Clearfog Base / Pro
reference boards.
The SoM has been designed as a pin-compatible replacement for the older
Armada 388 based SoM. Therefore it supports the same boards and a
similar feature set.
Most notable upgrades:
- 4x Cortex-A72
- 10Gbps SFP
- Both eMMC and SD supported at the same time
The developer first supporting this product at SolidRun decided to use
different filenames for the DTBs: Armada 388 uses the full
"clearfog" string while cn9130 uses the abbreviation "cf".
This name is already hard-coded in pre-installed vendor u-boot and can
not be changed easily.
NOTICE IN CASE ANYBODY WANTS TO SELF-UPGRADE:
CN9130 SoM has a different footprint from Armada 388 SoM.
Components on the carrier board below the SoM may collide causing
damage, such as on Clearfog Base.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---
arch/arm64/boot/dts/marvell/Makefile | 2 +
arch/arm64/boot/dts/marvell/cn9130-cf-base.dts | 178 ++++++++++++
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dts | 375 +++++++++++++++++++++++++
arch/arm64/boot/dts/marvell/cn9130-cf.dtsi | 197 +++++++++++++
arch/arm64/boot/dts/marvell/cn9130-sr-som.dtsi | 160 +++++++++++
5 files changed, 912 insertions(+)
diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
index 99b8cb3c49e1..019f2251d696 100644
--- a/arch/arm64/boot/dts/marvell/Makefile
+++ b/arch/arm64/boot/dts/marvell/Makefile
@@ -28,3 +28,5 @@ dtb-$(CONFIG_ARCH_MVEBU) += cn9130-crb-A.dtb
dtb-$(CONFIG_ARCH_MVEBU) += cn9130-crb-B.dtb
dtb-$(CONFIG_ARCH_MVEBU) += ac5x-rd-carrier-cn9131.dtb
dtb-$(CONFIG_ARCH_MVEBU) += ac5-98dx35xx-rd.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += cn9130-cf-base.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += cn9130-cf-pro.dtb
diff --git a/arch/arm64/boot/dts/marvell/cn9130-cf-base.dts b/arch/arm64/boot/dts/marvell/cn9130-cf-base.dts
new file mode 100644
index 000000000000..788a5c302b17
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/cn9130-cf-base.dts
@@ -0,0 +1,178 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2024 Josua Mayer <josua@solid-run.com>
+ *
+ * DTS for SolidRun CN9130 Clearfog Base.
+ *
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+#include "cn9130.dtsi"
+#include "cn9130-sr-som.dtsi"
+#include "cn9130-cf.dtsi"
+
+/ {
+ model = "SolidRun CN9130 Clearfog Base";
+ compatible = "solidrun,cn9130-clearfog-base",
+ "solidrun,cn9130-sr-som", "marvell,cn9130";
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&rear_button_pins>;
+ pinctrl-names = "default";
+
+ button-0 {
+ /* The rear SW3 button */
+ label = "Rear Button";
+ gpios = <&cp0_gpio1 31 GPIO_ACTIVE_LOW>;
+ linux,can-disable;
+ linux,code = <BTN_0>;
+ };
+ };
+
+ rfkill-m2-gnss {
+ compatible = "rfkill-gpio";
+ label = "m.2 GNSS";
+ radio-type = "gps";
+ /* rfkill-gpio inverts internally */
+ shutdown-gpios = <&expander0 9 GPIO_ACTIVE_HIGH>;
+ };
+
+ /* M.2 is B-keyed, so w-disable is for WWAN */
+ rfkill-m2-wwan {
+ compatible = "rfkill-gpio";
+ label = "m.2 WWAN";
+ radio-type = "wwan";
+ /* rfkill-gpio inverts internally */
+ shutdown-gpios = <&expander0 8 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+/* SRDS #3 - SGMII 1GE */
+&cp0_eth1 {
+ phy = <&phy1>;
+ phys = <&cp0_comphy3 1>;
+ phy-mode = "sgmii";
+ status = "okay";
+};
+
+&cp0_eth2_phy {
+ /*
+ * Configure LEDs default behaviour:
+ * - LED[0]: link/activity: On/blink (green)
+ * - LED[1]: link is 100/1000Mbps: On (yellow)
+ * - LED[2]: high impedance (floating)
+ */
+ marvell,reg-init = <3 16 0xf000 0x0a61>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_WAN;
+ default-state = "keep";
+ };
+
+ led@1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_YELLOW>;
+ function = LED_FUNCTION_WAN;
+ default-state = "keep";
+ };
+ };
+};
+
+&cp0_gpio1 {
+ sim-select-hog {
+ gpio-hog;
+ gpios = <27 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "sim-select";
+ };
+};
+
+&cp0_mdio {
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ /*
+ * Configure LEDs default behaviour:
+ * - LED[0]: link/activity: On/blink (green)
+ * - LED[1]: link is 100/1000Mbps: On (yellow)
+ * - LED[2]: high impedance (floating)
+ *
+ * Configure LEDs electrical polarity
+ * - on-state: low
+ * - off-state: high (not hi-z, to avoid residual glow)
+ */
+ marvell,reg-init = <3 16 0xf000 0x0a61>,
+ <3 17 0x003f 0x000a>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_LAN;
+ default-state = "keep";
+ };
+
+ led@1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_YELLOW>;
+ function = LED_FUNCTION_LAN;
+ default-state = "keep";
+ };
+ };
+ };
+};
+
+&cp0_pinctrl {
+ pinctrl-0 = <&sim_select_pins>;
+ pintrl-names = "default";
+
+ rear_button_pins: cp0-rear-button-pins {
+ marvell,pins = "mpp31";
+ marvell,function = "gpio";
+ };
+
+ sim_select_pins: cp0-sim-select-pins {
+ marvell,pins = "mpp27";
+ marvell,function = "gpio";
+ };
+};
+
+/*
+ * SRDS #4 - USB 3.0 host on M.2 connector
+ * USB-2.0 Host on Type-A connector
+ */
+&cp0_usb3_1 {
+ phys = <&cp0_comphy4 1>, <&cp0_utmi1>;
+ phy-names = "comphy", "utmi";
+ dr_mode = "host";
+ status = "okay";
+};
+
+&expander0 {
+ m2-full-card-power-off-hog {
+ gpio-hog;
+ gpios = <2 GPIO_ACTIVE_LOW>;
+ output-low;
+ line-name = "m2-full-card-power-off";
+ };
+
+ m2-reset-hog {
+ gpio-hog;
+ gpios = <10 GPIO_ACTIVE_LOW>;
+ output-low;
+ line-name = "m2-reset";
+ };
+};
diff --git a/arch/arm64/boot/dts/marvell/cn9130-cf-pro.dts b/arch/arm64/boot/dts/marvell/cn9130-cf-pro.dts
new file mode 100644
index 000000000000..a27fe0042867
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/cn9130-cf-pro.dts
@@ -0,0 +1,375 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2024 Josua Mayer <josua@solid-run.com>
+ *
+ * DTS for SolidRun CN9130 Clearfog Pro.
+ *
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+#include "cn9130.dtsi"
+#include "cn9130-sr-som.dtsi"
+#include "cn9130-cf.dtsi"
+
+/ {
+ model = "SolidRun CN9130 Clearfog Pro";
+ compatible = "solidrun,cn9130-clearfog-pro",
+ "solidrun,cn9130-sr-som", "marvell,cn9130";
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&rear_button_pins>;
+ pinctrl-names = "default";
+
+ button-0 {
+ /* The rear SW3 button */
+ label = "Rear Button";
+ gpios = <&cp0_gpio2 0 GPIO_ACTIVE_LOW>;
+ linux,can-disable;
+ linux,code = <BTN_0>;
+ };
+ };
+};
+
+/* SRDS #3 - SGMII 1GE to L2 switch */
+&cp0_eth1 {
+ phys = <&cp0_comphy3 1>;
+ phy-mode = "sgmii";
+ status = "okay";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&cp0_eth2_phy {
+ /*
+ * Configure LEDs default behaviour similar to switch ports:
+ * - LED[0]: link/activity: On/blink (green)
+ * - LED[1]: link is 100/1000Mbps: On (red)
+ * - LED[2]: high impedance (floating)
+ *
+ * Switch port defaults:
+ * - LED0: link/activity: On/blink (green)
+ * - LED1: link is 1000Mbps: On (red)
+ *
+ * Identical configuration is impossible with hardware offload.
+ */
+ marvell,reg-init = <3 16 0xf000 0x0a61>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_WAN;
+ label = "LED2";
+ default-state = "keep";
+ };
+
+ led@1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_RED>;
+ function = LED_FUNCTION_WAN;
+ label = "LED1";
+ default-state = "keep";
+ };
+ };
+};
+
+&cp0_mdio {
+ ethernet-switch@4 {
+ compatible = "marvell,mv88e6085";
+ reg = <4>;
+ pinctrl-0 = <&dsa_clk_pins &dsa_pins>;
+ pinctrl-names = "default";
+ reset-gpios = <&cp0_gpio1 27 GPIO_ACTIVE_LOW>;
+ interrupt-parent = <&cp0_gpio1>;
+ interrupts = <29 IRQ_TYPE_EDGE_FALLING>;
+
+ ethernet-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethernet-port@0 {
+ reg = <0>;
+ label = "lan5";
+ phy = <&switch0phy0>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_LAN;
+ label = "LED12";
+ default-state = "keep";
+ };
+
+ led@1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_RED>;
+ function = LED_FUNCTION_LAN;
+ label = "LED11";
+ default-state = "keep";
+ };
+ };
+ };
+
+ ethernet-port@1 {
+ reg = <1>;
+ label = "lan4";
+ phy = <&switch0phy1>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_LAN;
+ label = "LED10";
+ default-state = "keep";
+ };
+
+ led@1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_RED>;
+ function = LED_FUNCTION_LAN;
+ label = "LED9";
+ default-state = "keep";
+ };
+ };
+ };
+
+ ethernet-port@2 {
+ reg = <2>;
+ label = "lan3";
+ phy = <&switch0phy2>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_LAN;
+ label = "LED8";
+ default-state = "keep";
+ };
+
+ led@1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_RED>;
+ function = LED_FUNCTION_LAN;
+ label = "LED7";
+ default-state = "keep";
+ };
+ };
+ };
+
+ ethernet-port@3 {
+ reg = <3>;
+ label = "lan2";
+ phy = <&switch0phy3>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_LAN;
+ label = "LED6";
+ default-state = "keep";
+ };
+
+ led@1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_RED>;
+ function = LED_FUNCTION_LAN;
+ label = "LED5";
+ default-state = "keep";
+ };
+ };
+ };
+
+ ethernet-port@4 {
+ reg = <4>;
+ label = "lan1";
+ phy = <&switch0phy4>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_LAN;
+ label = "LED4";
+ default-state = "keep";
+ };
+
+ led@1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_RED>;
+ function = LED_FUNCTION_LAN;
+ label = "LED3";
+ default-state = "keep";
+ };
+ };
+ };
+
+ ethernet-port@5 {
+ reg = <5>;
+ label = "cpu";
+ ethernet = <&cp0_eth1>;
+ phy-mode = "sgmii";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ ethernet-port@6 {
+ reg = <6>;
+ label = "lan6";
+ phy-mode = "rgmii";
+
+ /*
+ * Because of mdio address conflict the
+ * external phy is not readable.
+ * Force a fixed link instead.
+ */
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ switch0phy0: ethernet-phy@0 {
+ reg = <0x0>;
+ };
+
+ switch0phy1: ethernet-phy@1 {
+ reg = <0x1>;
+ /*
+ * Indirectly configure default behaviour
+ * for port lan6 leds behind external phy.
+ * Internal PHYs are not using page 3,
+ * therefore writing to it is safe.
+ */
+ marvell,reg-init = <3 16 0xf000 0x0a61>;
+ };
+
+ switch0phy2: ethernet-phy@2 {
+ reg = <0x2>;
+ };
+
+ switch0phy3: ethernet-phy@3 {
+ reg = <0x3>;
+ };
+
+ switch0phy4: ethernet-phy@4 {
+ reg = <0x4>;
+ };
+ };
+
+ /*
+ * There is an external phy on the switch mdio bus.
+ * Because its mdio address collides with internal phys,
+ * it is not readable.
+ *
+ * mdio-external {
+ * compatible = "marvell,mv88e6xxx-mdio-external";
+ * #address-cells = <1>;
+ * #size-cells = <0>;
+ *
+ * ethernet-phy@1 {
+ * reg = <0x1>;
+ * };
+ * };
+ */
+ };
+};
+
+/* SRDS #4 - miniPCIe (CON2) */
+&cp0_pcie1 {
+ num-lanes = <1>;
+ phys = <&cp0_comphy4 1>;
+ /* dw-pcie inverts internally */
+ reset-gpios = <&expander0 2 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&cp0_pinctrl {
+ dsa_clk_pins: cp0-dsa-clk-pins {
+ marvell,pins = "mpp40";
+ marvell,function = "synce1";
+ };
+
+ dsa_pins: cp0-dsa-pins {
+ marvell,pins = "mpp27", "mpp29";
+ marvell,function = "gpio";
+ };
+
+ rear_button_pins: cp0-rear-button-pins {
+ marvell,pins = "mpp32";
+ marvell,function = "gpio";
+ };
+
+ cp0_spi1_cs1_pins: cp0-spi1-cs1-pins {
+ marvell,pins = "mpp12";
+ marvell,function = "spi1";
+ };
+};
+
+&cp0_spi1 {
+ /* add pin for chip-select 1 on mikrobus */
+ pinctrl-0 = <&cp0_spi1_pins &cp0_spi1_cs1_pins>;
+};
+
+/* USB-2.0 Host on Type-A connector */
+&cp0_usb3_1 {
+ phys = <&cp0_utmi1>;
+ phy-names = "utmi";
+ dr_mode = "host";
+ status = "okay";
+};
+
+&expander0 {
+ /* CON2 */
+ pcie1-0-clkreq-hog {
+ gpio-hog;
+ gpios = <4 GPIO_ACTIVE_LOW>;
+ input;
+ line-name = "pcie1.0-clkreq";
+ };
+
+ /* CON2 */
+ pcie1-0-w-disable-hog {
+ gpio-hog;
+ gpios = <7 GPIO_ACTIVE_LOW>;
+ output-low;
+ line-name = "pcie1.0-w-disable";
+ };
+};
diff --git a/arch/arm64/boot/dts/marvell/cn9130-cf.dtsi b/arch/arm64/boot/dts/marvell/cn9130-cf.dtsi
new file mode 100644
index 000000000000..0a0ba2fce537
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/cn9130-cf.dtsi
@@ -0,0 +1,197 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2024 Josua Mayer <josua@solid-run.com>
+ *
+ * DTS for common base of SolidRun CN9130 Clearfog Base and Pro.
+ *
+ */
+
+/ {
+ aliases {
+ /* label nics same order as armada 388 clearfog */
+ ethernet0 = &cp0_eth2;
+ ethernet1 = &cp0_eth1;
+ ethernet2 = &cp0_eth0;
+ i2c1 = &cp0_i2c1;
+ mmc1 = &cp0_sdhci0;
+ };
+
+ reg_usb3_vbus0: regulator-usb3-vbus0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vbus0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&expander0 6 GPIO_ACTIVE_LOW>;
+ };
+
+ sfp: sfp {
+ compatible = "sff,sfp";
+ i2c-bus = <&cp0_i2c1>;
+ los-gpios = <&expander0 12 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&expander0 15 GPIO_ACTIVE_LOW>;
+ tx-disable-gpios = <&expander0 14 GPIO_ACTIVE_HIGH>;
+ tx-fault-gpios = <&expander0 13 GPIO_ACTIVE_HIGH>;
+ maximum-power-milliwatt = <2000>;
+ };
+};
+
+/* SRDS #2 - SFP+ 10GE */
+&cp0_eth0 {
+ managed = "in-band-status";
+ phys = <&cp0_comphy2 0>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp>;
+ status = "okay";
+};
+
+&cp0_i2c0 {
+ expander0: gpio-expander@20 {
+ compatible = "nxp,pca9555";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ pinctrl-0 = <&expander0_pins>;
+ pinctrl-names = "default";
+ interrupt-parent = <&cp0_gpio1>;
+ interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+
+ /* CON3 */
+ pcie2-0-clkreq-hog {
+ gpio-hog;
+ gpios = <0 GPIO_ACTIVE_LOW>;
+ input;
+ line-name = "pcie2.0-clkreq";
+ };
+
+ /* CON3 */
+ pcie2-0-w-disable-hog {
+ gpio-hog;
+ gpios = <3 GPIO_ACTIVE_LOW>;
+ output-low;
+ line-name = "pcie2.0-w-disable";
+ };
+
+ usb3-ilimit-hog {
+ gpio-hog;
+ gpios = <5 GPIO_ACTIVE_LOW>;
+ input;
+ line-name = "usb3-current-limit";
+ };
+
+ m2-devslp-hog {
+ gpio-hog;
+ gpios = <11 GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "m.2 devslp";
+ };
+ };
+
+ /* The MCP3021 supports standard and fast modes */
+ adc@4c {
+ compatible = "microchip,mcp3021";
+ reg = <0x4c>;
+ };
+
+ carrier_eeprom: eeprom@52 {
+ compatible = "atmel,24c02";
+ reg = <0x52>;
+ pagesize = <8>;
+ };
+};
+
+&cp0_i2c1 {
+ /*
+ * Routed to SFP, M.2, mikrobus, and miniPCIe
+ * SFP limits this to 100kHz, and requires an AT24C01A/02/04 with
+ * address pins tied low, which takes addresses 0x50 and 0x51.
+ * Mikrobus doesn't specify beyond an I2C bus being present.
+ * PCIe uses ARP to assign addresses, or 0x63-0x64.
+ */
+ clock-frequency = <100000>;
+ pinctrl-0 = <&cp0_i2c1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+/* SRDS #5 - miniPCIe (CON3) */
+&cp0_pcie2 {
+ num-lanes = <1>;
+ phys = <&cp0_comphy5 2>;
+ /* dw-pcie inverts internally */
+ reset-gpios = <&expander0 1 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&cp0_pinctrl {
+ cp0_i2c1_pins: cp0-i2c1-pins {
+ marvell,pins = "mpp35", "mpp36";
+ marvell,function = "i2c1";
+ };
+
+ cp0_mmc0_pins: cp0-mmc0-pins {
+ marvell,pins = "mpp43", "mpp56", "mpp57", "mpp58",
+ "mpp59", "mpp60", "mpp61";
+ marvell,function = "sdio";
+ };
+
+ mikro_spi_pins: cp0-spi1-cs1-pins {
+ marvell,pins = "mpp12";
+ marvell,function = "spi1";
+ };
+
+ mikro_uart_pins: cp0-uart-pins {
+ marvell,pins = "mpp2", "mpp3";
+ marvell,function = "uart1";
+ };
+
+ expander0_pins: cp0-expander0-pins {
+ marvell,pins = "mpp4";
+ marvell,function = "gpio";
+ };
+};
+
+/* SRDS #0 - SATA on M.2 connector */
+&cp0_sata0 {
+ phys = <&cp0_comphy0 1>;
+ status = "okay";
+
+ /* only port 1 is available */
+ /delete-node/ sata-port@0;
+};
+
+/* microSD */
+&cp0_sdhci0 {
+ pinctrl-0 = <&cp0_mmc0_pins>;
+ pinctrl-names = "default";
+ bus-width = <4>;
+ no-1-8-v;
+ status = "okay";
+};
+
+&cp0_spi1 {
+ /* CS1 for mikrobus */
+ pinctrl-0 = <&cp0_spi1_pins &mikro_spi_pins>;
+};
+
+/*
+ * SRDS #1 - USB-3.0 Host on Type-A connector
+ * USB-2.0 Host on mPCI-e connector (CON3)
+ */
+&cp0_usb3_0 {
+ phys = <&cp0_comphy1 0>, <&cp0_utmi0>;
+ phy-names = "comphy", "utmi";
+ vbus-supply = <®_usb3_vbus0>;
+ dr_mode = "host";
+ status = "okay";
+};
+
+&cp0_utmi {
+ status = "okay";
+};
+
+/* mikrobus uart */
+&cp0_uart0 {
+ pinctrl-0 = <&mikro_uart_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/marvell/cn9130-sr-som.dtsi b/arch/arm64/boot/dts/marvell/cn9130-sr-som.dtsi
new file mode 100644
index 000000000000..8f0238a45a58
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/cn9130-sr-som.dtsi
@@ -0,0 +1,160 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2024 Josua Mayer <josua@solid-run.com>
+ *
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "SolidRun CN9130 SoM";
+ compatible = "solidrun,cn9130-sr-som", "marvell,cn9130";
+
+ aliases {
+ ethernet0 = &cp0_eth0;
+ ethernet1 = &cp0_eth1;
+ ethernet2 = &cp0_eth2;
+ i2c0 = &cp0_i2c0;
+ mmc0 = &ap_sdhci0;
+ rtc0 = &cp0_rtc;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ v_1_8: regulator-1-8 {
+ compatible = "regulator-fixed";
+ regulator-name = "1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ /* requires assembly of R9307 */
+ vhv: regulator-vhv-1-8 {
+ compatible = "regulator-fixed";
+ regulator-name = "vhv-1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ pinctrl-0 = <&cp0_reg_vhv_pins>;
+ pinctrl-names = "default";
+ gpio = <&cp0_gpio2 9 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+};
+
+&ap_pinctrl {
+ ap_mmc0_pins: ap-mmc0-pins {
+ marvell,pins = "mpp0", "mpp1", "mpp2", "mpp3", "mpp4", "mpp5",
+ "mpp6", "mpp7", "mpp8", "mpp9", "mpp10", "mpp12";
+ marvell,function = "sdio";
+ /*
+ * mpp12 is emmc reset, function should be sdio (hw_rst),
+ * but pinctrl-mvebu does not support this.
+ *
+ * From pinctrl-mvebu.h:
+ * "The name will be used to switch to this setting in DT description, e.g.
+ * marvell,function = "uart2". subname is only for debugging purposes."
+ */
+ };
+};
+
+&ap_sdhci0 {
+ bus-width = <8>;
+ pinctrl-0 = <&ap_mmc0_pins>;
+ pinctrl-names = "default";
+ vqmmc-supply = <&v_1_8>;
+ status = "okay";
+};
+
+&cp0_ethernet {
+ status = "okay";
+};
+
+/* for assembly with phy */
+&cp0_eth2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_eth2_pins>;
+ phy-mode = "rgmii-id";
+ phy = <&cp0_eth2_phy>;
+ status = "okay";
+};
+
+&cp0_i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_i2c0_pins>;
+ clock-frequency = <100000>;
+ status = "okay";
+
+ som_eeprom: eeprom@53 {
+ compatible = "atmel,24c02";
+ reg = <0x53>;
+ pagesize = <8>;
+ };
+};
+
+&cp0_mdio {
+ pinctrl-0 = <&cp0_mdio_pins>;
+ status = "okay";
+
+ /* assembly option */
+ cp0_eth2_phy: ethernet-phy@0 {
+ reg = <0>;
+ };
+};
+
+&cp0_spi1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_spi1_pins>;
+ /* max speed limited by a mux */
+ spi-max-frequency = <1800000000>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ /* read command supports max. 50MHz */
+ spi-max-frequency = <50000000>;
+ };
+};
+
+&cp0_syscon0 {
+ cp0_pinctrl: pinctrl {
+ compatible = "marvell,cp115-standalone-pinctrl";
+
+ cp0_eth2_pins: cp0-ge2-rgmii-pins {
+ marvell,pins = "mpp44", "mpp45", "mpp46", "mpp47",
+ "mpp48", "mpp49", "mpp50", "mpp51",
+ "mpp52", "mpp53", "mpp54", "mpp55";
+ /* docs call it "ge2", but cp110-pinctrl "ge1" */
+ marvell,function = "ge1";
+ };
+
+ cp0_i2c0_pins: cp0-i2c0-pins {
+ marvell,pins = "mpp37", "mpp38";
+ marvell,function = "i2c0";
+ };
+
+ cp0_mdio_pins: cp0-mdio-pins {
+ marvell,pins = "mpp40", "mpp41";
+ marvell,function = "ge";
+ };
+
+ cp0_spi1_pins: cp0-spi1-pins {
+ marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16";
+ marvell,function = "spi1";
+ };
+
+ cp0_reg_vhv_pins: cp0-reg-vhv-pins {
+ marvell,pins = "mpp41";
+ marvell,function = "gpio";
+ };
+ };
+};
+
+/* AP default console */
+&uart0 {
+ pinctrl-0 = <&uart0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
--
2.35.3
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH v4 4/4] arm64: dts: add description for solidrun cn9131 solidwan board
2024-05-02 12:32 [PATCH v4 0/4] arm64: dts: add description for solidrun cn9130 som and clearfog boards Josua Mayer
` (2 preceding siblings ...)
2024-05-02 12:32 ` [PATCH v4 3/4] arm64: dts: add description for solidrun cn9130 som and clearfog boards Josua Mayer
@ 2024-05-02 12:32 ` Josua Mayer
2024-05-02 15:20 ` Rob Herring
2024-05-02 17:35 ` Josua Mayer
2024-05-02 15:08 ` [PATCH v4 0/4] arm64: dts: add description for solidrun cn9130 som and clearfog boards Rob Herring (Arm)
4 siblings, 2 replies; 11+ messages in thread
From: Josua Mayer @ 2024-05-02 12:32 UTC (permalink / raw)
To: Andrew Lunn, Gregory Clement, Sebastian Hesselbarth, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Rob Herring
Cc: Yazan Shhady, linux-arm-kernel, devicetree, linux-kernel,
Josua Mayer
Add description for the SolidRun CN9131 SolidWAN, based on CN9130 SoM
with an extra communication processor on the carrier board.
This board differentiates itself from CN9130 Clearfog by providing
additional SoC native network interfaces and pci buses:
2x 10Gbps SFP+
4x 1Gbps RJ45
1x miniPCI-E
1x m.2 b-key with sata, usb-2.0 and usb-3.0
1x m.2 m-key with pcie and usb-2.0
1x m.2 b-key with pcie, usb-2.0, usb-3.0 and 2x sim slots
1x mpcie with pcie only
2x type-a usb-2.0/3.0
Signed-off-by: Josua Mayer <josua@solid-run.com>
---
arch/arm64/boot/dts/marvell/Makefile | 1 +
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dts | 643 +++++++++++++++++++++
2 files changed, 644 insertions(+)
diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
index 019f2251d696..16f9d7156d9f 100644
--- a/arch/arm64/boot/dts/marvell/Makefile
+++ b/arch/arm64/boot/dts/marvell/Makefile
@@ -30,3 +30,4 @@ dtb-$(CONFIG_ARCH_MVEBU) += ac5x-rd-carrier-cn9131.dtb
dtb-$(CONFIG_ARCH_MVEBU) += ac5-98dx35xx-rd.dtb
dtb-$(CONFIG_ARCH_MVEBU) += cn9130-cf-base.dtb
dtb-$(CONFIG_ARCH_MVEBU) += cn9130-cf-pro.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += cn9131-cf-solidwan.dtb
diff --git a/arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dts b/arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dts
new file mode 100644
index 000000000000..a63a8961bad0
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dts
@@ -0,0 +1,643 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2024 Josua Mayer <josua@solid-run.com>
+ *
+ * DTS for SolidRun CN9130 Clearfog Base.
+ *
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+#include "cn9130.dtsi"
+#include "cn9130-sr-som.dtsi"
+
+/*
+ * Instantiate the external CP115
+ */
+
+#define CP11X_NAME cp1
+#define CP11X_BASE f4000000
+#define CP11X_PCIEx_MEM_BASE(iface) (0xe2000000 + (iface * 0x1000000))
+#define CP11X_PCIEx_MEM_SIZE(iface) 0xf00000
+#define CP11X_PCIE0_BASE f4600000
+#define CP11X_PCIE1_BASE f4620000
+#define CP11X_PCIE2_BASE f4640000
+
+#include "armada-cp115.dtsi"
+
+#undef CP11X_NAME
+#undef CP11X_BASE
+#undef CP11X_PCIEx_MEM_BASE
+#undef CP11X_PCIEx_MEM_SIZE
+#undef CP11X_PCIE0_BASE
+#undef CP11X_PCIE1_BASE
+#undef CP11X_PCIE2_BASE
+
+/ {
+ model = "SolidRun CN9131 SolidWAN";
+ compatible = "solidrun,cn9131-solidwan",
+ "solidrun,cn9130-sr-som", "marvell,cn9130";
+
+ aliases {
+ ethernet0 = &cp1_eth1;
+ ethernet1 = &cp1_eth2;
+ ethernet2 = &cp0_eth1;
+ ethernet3 = &cp0_eth2;
+ ethernet4 = &cp0_eth0;
+ ethernet5 = &cp1_eth0;
+ gpio0 = &ap_gpio;
+ gpio1 = &cp0_gpio1;
+ gpio2 = &cp0_gpio2;
+ gpio3 = &cp1_gpio1;
+ gpio4 = &cp1_gpio2;
+ gpio5 = &expander0;
+ i2c0 = &cp0_i2c0;
+ i2c1 = &cp0_i2c1;
+ i2c2 = &cp1_i2c1;
+ mmc0 = &ap_sdhci0;
+ mmc1 = &cp0_sdhci0;
+ rtc0 = &cp0_rtc;
+ rtc1 = &carrier_rtc;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_led_pins &cp1_led_pins>;
+
+ /* for sfp-1 (J42) */
+ led-sfp1-activity {
+ label = "sfp1:green";
+ gpios = <&cp0_gpio1 7 GPIO_ACTIVE_HIGH>;
+ };
+
+ /* for sfp-1 (J42) */
+ led-sfp1-link {
+ label = "sfp1:yellow";
+ gpios = <&cp0_gpio1 4 GPIO_ACTIVE_HIGH>;
+ };
+
+ /* (J28) */
+ led-sfp0-activity {
+ label = "sfp0:green";
+ gpios = <&cp1_gpio2 22 GPIO_ACTIVE_HIGH>;
+ };
+
+ /* (J28) */
+ led-sfp0-link {
+ label = "sfp0:yellow";
+ gpios = <&cp1_gpio2 23 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ /* Type-A port on J53 */
+ reg_usb_a_vbus0: regulator-usb-a-vbus0 {
+ compatible = "regulator-fixed";
+ pinctrl-0 = <&cp0_reg_usb_a_vbus0_pins>;
+ pinctrl-names = "default";
+ regulator-name = "vbus0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-oc-protection-microamp = <1000000>;
+ gpio = <&cp0_gpio1 27 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ reg_usb_a_vbus1: regulator-usb-a-vbus1 {
+ compatible = "regulator-fixed";
+ pinctrl-0 = <&cp0_reg_usb_a_vbus1_pins>;
+ pinctrl-names = "default";
+ regulator-name = "vbus1";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-oc-protection-microamp = <1000000>;
+ gpio = <&cp0_gpio1 28 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ sfp0: sfp-0 {
+ compatible = "sff,sfp";
+ pinctrl-0 = <&cp0_sfp0_pins>;
+ pinctrl-names = "default";
+ i2c-bus = <&cp0_i2c1>;
+ los-gpio = <&cp0_gpio2 2 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpio = <&cp0_gpio2 0 GPIO_ACTIVE_LOW>;
+ tx-disable-gpio = <&cp0_gpio2 1 GPIO_ACTIVE_HIGH>;
+ tx-fault-gpio = <&cp0_gpio1 31 GPIO_ACTIVE_HIGH>;
+ maximum-power-milliwatt = <2000>;
+ };
+
+ sfp1: sfp-1 {
+ compatible = "sff,sfp";
+ pinctrl-0 = <&cp1_sfp1_pins>;
+ pinctrl-names = "default";
+ i2c-bus = <&cp1_i2c1>;
+ los-gpio = <&cp1_gpio2 2 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpio = <&cp1_gpio2 18 GPIO_ACTIVE_LOW>;
+ tx-disable-gpio = <&cp1_gpio2 1 GPIO_ACTIVE_HIGH>;
+ tx-fault-gpio = <&cp1_gpio2 17 GPIO_ACTIVE_HIGH>;
+ maximum-power-milliwatt = <2000>;
+ };
+};
+
+&cp0_ethernet {
+ status = "okay";
+};
+
+/* SRDS #2 - SFP+ 10GE */
+&cp0_eth0 {
+ managed = "in-band-status";
+ phy-mode = "10gbase-r";
+ phys = <&cp0_comphy2 0>;
+ sfp = <&sfp0>;
+ status = "okay";
+};
+
+/* SRDS #3 - SGMII 1GE */
+&cp0_eth1 {
+ managed = "in-band-status";
+ phy-mode = "sgmii";
+ /* Without mdio phy access rely on sgmii auto-negotiation. */
+ phys = <&cp0_comphy3 1>;
+ status = "okay";
+};
+
+/* SRDS #1 - SGMII */
+&cp0_eth2 {
+ /delete-property/ pinctrl-0;
+ /delete-property/ pinctrl-names;
+ managed = "in-band-status";
+ phy-mode = "sgmii";
+ phy = <&cp0_phy1>;
+ phys = <&cp0_comphy1 2>;
+};
+
+&cp0_gpio1 {
+ pcie0-0-w-disable-hog {
+ gpio-hog;
+ gpios = <6 GPIO_ACTIVE_LOW>;
+ output-low;
+ line-name = "pcie0.0-w-disable";
+ };
+
+ /* J34 */
+ m2-full-card-power-off-hog {
+ gpio-hog;
+ gpios = <8 GPIO_ACTIVE_LOW>;
+ output-low;
+ line-name = "m2-full-card-power-off";
+ };
+};
+
+&cp0_i2c0 {
+ /* assembly option */
+ fan-controller@18 {
+ compatible = "ti,amc6821";
+ reg = <0x18>;
+ };
+
+ expander0: gpio@41 {
+ compatible = "nxp,pca9536";
+ reg = <0x41>;
+
+ usb-a-vbus0-ilimit-hog {
+ gpio-hog;
+ gpios = <0 GPIO_ACTIVE_LOW>;
+ input;
+ line-name = "vbus0-ilimit";
+ };
+
+ /* duplicate connection, controlled by soc gpio */
+ usb-vbus0-enable-hog {
+ gpio-hog;
+ gpios = <1 GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "vbus0-enable";
+ };
+
+ usb-a-vbus1-ilimit-hog {
+ gpio-hog;
+ gpios = <2 GPIO_ACTIVE_LOW>;
+ input;
+ line-name = "vbus1-ilimit";
+ };
+
+ /* duplicate connection, controlled by soc gpio */
+ usb-vbus1-enable-hog {
+ gpio-hog;
+ gpios = <3 GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "vbus1-enable";
+ };
+ };
+
+ carrier_eeprom: eeprom@52 {
+ compatible = "atmel,24c02";
+ reg = <0x52>;
+ pagesize = <8>;
+ };
+
+ /* usb-hub@60 */
+
+ /* assembly option */
+ carrier_rtc: rtc@68 {
+ compatible = "st,m41t83";
+ reg = <0x68>;
+ pinctrl-0 = <&cp1_rtc_pins>;
+ pinctrl-names = "default";
+ interrupt-parent = <&cp1_gpio1>;
+ interrupts = <12 IRQ_TYPE_EDGE_FALLING>;
+ reset-gpios = <&cp1_gpio1 13 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&cp0_i2c1 {
+ /*
+ * Routed to SFP.
+ * Limit to 100kHz for compatibility with SFP modules,
+ * featuring AT24C01A/02/04 at addresses 0x50/0x51.
+ */
+ clock-frequency = <100000>;
+ pinctrl-0 = <&cp0_i2c1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&cp0_mdio {
+ /*
+ * SoM + Carrier each have a PHY at address 0.
+ * Remove the SoM phy node, and skip adding the carrier node.
+ * SGMII Auto-Negotation is enabled by bootloader for
+ * autonomous operation without mdio control.
+ */
+ /delete-node/ ethernet-phy@0;
+
+ /* U17016 */
+ cp0_phy1: ethernet-phy@1 {
+ reg = <1>;
+ /*
+ * Configure LEDs default behaviour:
+ * - LED[0]: link is 1000Mbps: On (yellow)
+ * - LED[1]: link/activity: On/blink (green)
+ * - LED[2]: high impedance (floating)
+ */
+ marvell,reg-init = <3 16 0xf000 0x0a17>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_YELLOW>;
+ function = LED_FUNCTION_LAN;
+ default-state = "keep";
+ };
+
+ led@1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_LAN;
+ default-state = "keep";
+ };
+ };
+ };
+};
+
+/* SRDS #0 - miniPCIe */
+&cp0_pcie0 {
+ num-lanes = <1>;
+ phys = <&cp0_comphy0 0>;
+ status = "okay";
+};
+
+/* SRDS #5 - M.2 B-Key (J34) */
+&cp0_pcie2 {
+ num-lanes = <1>;
+ phys = <&cp0_comphy5 2>;
+ status = "okay";
+};
+
+&cp0_pinctrl {
+ pinctrl-0 = <&cp0_m2_0_shutdown_pins &cp0_mpcie_rfkill_pins>;
+ pinctrl-names = "default";
+
+ cp0_i2c1_pins: cp0-i2c1-pins {
+ marvell,pins = "mpp35", "mpp36";
+ marvell,function = "i2c1";
+ };
+
+ cp0_led_pins: cp0-led-pins {
+ marvell,pins = "mpp4", "mpp7";
+ marvell,function = "gpio";
+ };
+
+ cp0_m2_0_shutdown_pins: cp0-m2-0-shutdown-pins {
+ marvell,pins = "mpp8";
+ marvell,function = "gpio";
+ };
+
+ cp0_mmc0_pins: cp0-mmc0-pins {
+ marvell,pins = "mpp43", "mpp56", "mpp57", "mpp58",
+ "mpp59", "mpp60", "mpp61";
+ marvell,function = "sdio";
+ };
+
+ cp0_mpcie_rfkill_pins: cp0-mpcie-rfkill-pins {
+ marvell,pins = "mpp6";
+ marvell,function = "gpio";
+ };
+
+ cp0_reg_usb_a_vbus0_pins: cp0-reg-usb-a-vbus0-pins {
+ marvell,pins = "mpp27";
+ marvell,function = "gpio";
+ };
+
+ cp0_reg_usb_a_vbus1_pins: cp0-reg-usb-a-vbus1-pins {
+ marvell,pins = "mpp28";
+ marvell,function = "gpio";
+ };
+
+ cp0_sfp0_pins: cp0-sfp0-pins {
+ marvell,pins = "mpp31", "mpp32", "mpp33", "mpp34";
+ marvell,function = "gpio";
+ };
+
+ cp0_spi1_cs1_pins: cp0-spi1-cs1-pins {
+ marvell,pins = "mpp12";
+ marvell,function = "spi1";
+ };
+};
+
+/* microSD */
+&cp0_sdhci0 {
+ pinctrl-0 = <&cp0_mmc0_pins>;
+ pinctrl-names = "default";
+ bus-width = <4>;
+ no-1-8-v;
+ status = "okay";
+};
+
+&cp0_spi1 {
+ /* add pin for chip-select 1 */
+ pinctrl-0 = <&cp0_spi1_pins &cp0_spi1_cs1_pins>;
+
+ flash@1 {
+ compatible = "jedec,spi-nor";
+ reg = <1>;
+ /* read command supports max. 50MHz */
+ spi-max-frequency = <50000000>;
+ };
+};
+
+/* USB-2.0 Host to USB-Hub */
+&cp0_usb3_0 {
+ phys = <&cp0_utmi0>;
+ phy-names = "utmi";
+ dr_mode = "host";
+ status = "okay";
+};
+
+/* SRDS #4 - USB-3.0 Host to USB-Hub */
+&cp0_usb3_1 {
+ phys = <&cp0_comphy4 1>, <&cp0_utmi1>;
+ phy-names = "comphy", "utmi";
+ dr_mode = "host";
+ status = "okay";
+};
+
+&cp0_utmi {
+ status = "okay";
+};
+
+&cp0_utmi {
+ status = "okay";
+};
+
+&cp0_utmi1 {
+ status = "disabled";
+};
+
+&cp1_ethernet {
+ status = "okay";
+};
+
+/* SRDS #4 - SFP+ 10GE */
+&cp1_eth0 {
+ managed = "in-band-status";
+ phy-mode = "10gbase-r";
+ phys = <&cp1_comphy4 0>;
+ sfp = <&sfp1>;
+ status = "okay";
+};
+
+/* SRDS #3 - SGMII 1GE */
+&cp1_eth1 {
+ managed = "in-band-status";
+ phy-mode = "sgmii";
+ phy = <&cp1_phy0>;
+ phys = <&cp0_comphy3 1>;
+ status = "okay";
+};
+
+/* SRDS #5 - SGMII 1GE */
+&cp1_eth2 {
+ managed = "in-band-status";
+ phy-mode = "sgmii";
+ phy = <&cp1_phy1>;
+ phys = <&cp0_comphy5 2>;
+ status = "okay";
+};
+
+&cp1_gpio1 {
+ status = "okay";
+
+ /* J30 */
+ m2-full-card-power-off-hog-0 {
+ gpio-hog;
+ gpios = <29 GPIO_ACTIVE_LOW>;
+ output-low;
+ line-name = "m2-full-card-power-off";
+ };
+
+ /* J44 */
+ m2-full-card-power-off-hog-1 {
+ gpio-hog;
+ gpios = <30 GPIO_ACTIVE_LOW>;
+ output-low;
+ line-name = "m2-full-card-power-off";
+ };
+};
+
+&cp1_gpio2 {
+ status = "okay";
+};
+
+&cp1_i2c1 {
+ /*
+ * Routed to SFP.
+ * Limit to 100kHz for compatibility with SFP modules,
+ * featuring AT24C01A/02/04 at addresses 0x50/0x51.
+ */
+ clock-frequency = <100000>;
+ pinctrl-0 = <&cp1_i2c1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&cp1_mdio {
+ pinctrl-0 = <&cp1_mdio_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ cp1_phy0: ethernet-phy@0 {
+ reg = <0>;
+ /*
+ * Configure LEDs default behaviour:
+ * - LED[0]: link is 1000Mbps: On (yellow)
+ * - LED[1]: link/activity: On/blink (green)
+ * - LED[2]: high impedance (floating)
+ */
+ marvell,reg-init = <3 16 0xf000 0x0a17>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_YELLOW>;
+ function = LED_FUNCTION_LAN;
+ default-state = "keep";
+ };
+
+ led@1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_LAN;
+ default-state = "keep";
+ };
+ };
+ };
+
+ cp1_phy1: ethernet-phy@1 {
+ reg = <1>;
+ /*
+ * Configure LEDs default behaviour:
+ * - LED[0]: link is 1000Mbps: On (yellow)
+ * - LED[1]: link/activity: On/blink (green)
+ * - LED[2]: high impedance (floating)
+ */
+ marvell,reg-init = <3 16 0xf000 0x0a17>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_YELLOW>;
+ function = LED_FUNCTION_LAN;
+ default-state = "keep";
+ };
+
+ led@1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_LAN;
+ default-state = "keep";
+ };
+ };
+ };
+};
+
+/* SRDS #0 - M.2 (J30) */
+&cp1_pcie0 {
+ num-lanes = <1>;
+ phys = <&cp1_comphy0 0>;
+ status = "okay";
+};
+
+&cp1_rtc {
+ status = "disabled";
+};
+
+/* SRDS #1 - SATA on M.2 (J44) */
+&cp1_sata0 {
+ phys = <&cp1_comphy1 0>;
+ status = "okay";
+
+ /* only port 0 is available */
+ /delete-node/ sata-port@1;
+};
+
+&cp1_syscon0 {
+ cp1_pinctrl: pinctrl {
+ compatible = "marvell,cp115-standalone-pinctrl";
+ pinctrl-0 = <&cp1_m2_1_shutdown_pins &cp1_m2_2_shutdown_pins>;
+ pinctrl-names = "default";
+
+ cp1_i2c1_pins: cp0-i2c1-pins {
+ marvell,pins = "mpp35", "mpp36";
+ marvell,function = "i2c1";
+ };
+
+ cp1_led_pins: cp1-led-pins {
+ marvell,pins = "mpp54", "mpp55";
+ marvell,function = "gpio";
+ };
+
+ cp1_m2_1_shutdown_pins: cp1-m2-1-shutdown-pins {
+ marvell,pins = "mpp29";
+ marvell,function = "gpio";
+ };
+
+ cp1_m2_2_shutdown_pins: cp1-m2-2-shutdown-pins {
+ marvell,pins = "mpp30";
+ marvell,function = "gpio";
+ };
+
+ cp1_mdio_pins: cp1-mdio-pins {
+ marvell,pins = "mpp37", "mpp38";
+ marvell,function = "ge";
+ };
+
+ cp1_rtc_pins: cp1-rtc-pins {
+ marvell,pins = "mpp12", "mpp13";
+ marvell,function = "gpio";
+ };
+
+ cp1_sfp1_pins: cp1-sfp1-pins {
+ marvell,pins = "mpp33", "mpp34", "mpp49", "mpp50";
+ marvell,function = "gpio";
+ };
+ };
+};
+
+/*
+ * SRDS #2 - USB-3.0 Host to M.2 (J44)
+ * USB-2.0 Host to M.2 (J30)
+ */
+&cp1_usb3_0 {
+ phys = <&cp1_comphy2 0>, <&cp1_utmi0>;
+ phy-names = "comphy", "utmi";
+ dr_mode = "host";
+ status = "okay";
+};
+
+/* USB-2.0 Host to M.2 (J44) */
+&cp1_usb3_1 {
+ phys = <&cp1_utmi1>;
+ phy-names = "utmi";
+ dr_mode = "host";
+ status = "okay";
+};
+
+&cp1_utmi {
+ status = "okay";
+};
--
2.35.3
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 11+ messages in thread
* Re: [PATCH v4 0/4] arm64: dts: add description for solidrun cn9130 som and clearfog boards
2024-05-02 12:32 [PATCH v4 0/4] arm64: dts: add description for solidrun cn9130 som and clearfog boards Josua Mayer
` (3 preceding siblings ...)
2024-05-02 12:32 ` [PATCH v4 4/4] arm64: dts: add description for solidrun cn9131 solidwan board Josua Mayer
@ 2024-05-02 15:08 ` Rob Herring (Arm)
4 siblings, 0 replies; 11+ messages in thread
From: Rob Herring (Arm) @ 2024-05-02 15:08 UTC (permalink / raw)
To: Josua Mayer
Cc: Conor Dooley, Krzysztof Kozlowski, linux-arm-kernel, Rob Herring,
Gregory Clement, Yazan Shhady, Krzysztof Kozlowski, devicetree,
Sebastian Hesselbarth, linux-kernel, Andrew Lunn
On Thu, 02 May 2024 14:32:14 +0200, Josua Mayer wrote:
> SolidRun CN9130 SoM is a mostly pin-comptible replacement for Armada 388
> SoM used in Clearfog and Clearfog Pro boards.
>
> 1. Add new binding for compatible strings closely matching the original.
>
> 2. Add device-tree includes for SoM and carrier shared design.
>
> 3. Add device-tree for both Clearfog Base and Pro.
>
> While dtbs_check is happy with LED descriptions behind dsa switch,
> functionally they require supporting code by Andrew Lunn:
> https://lore.kernel.org/r/20240401-v6-8-0-net-next-mv88e6xxx-leds-v4-v3-0-221b3fa55f78@lunn.ch
>
> NOTICE IN CASE ANYBODY WANTS TO SELF-UPGRADE:
> CN9130 SoM has a different footprint from Armada 388 SoM.
> Components on the carrier board below the SoM may collide causing
> damage, such as on Clearfog Base.
>
> Signed-off-by: Josua Mayer <josua@solid-run.com>
> ---
> Changes in v4:
> - Picked up reviewed-by tags by Andrew Lunn.
> - fixed a typo and changed 3-line comment into single-line comment
> for clearfog-base/-pro dts, but kept review tags since change was
> minor.
> - Updated SFP led labels to use "sfp?:colour" without "color" property,
> to avoid duplicate labels while reflecting they are each dual-colour.
> - Link to v3: https://lore.kernel.org/r/20240414-cn9130-som-v3-0-350a67d44e0a@solid-run.com
>
> Changes in v3:
> - picked up acked-by for dt-bindings
> - skipped acked-by for dts because additional changes were made:
> - moved legacy netdev aliases to carrier dts
> - fix status property style errors
> - add pinctrl for secondary spi chip-select on mikrobus header (& som)
> - specify spi bus frequency limits for som
> - Added CN9131 SolidWAN board
> - Link to v2: https://lore.kernel.org/r/20240404-cn9130-som-v2-0-3af2229c7d2d@solid-run.com
>
> Changes in v2:
> - rewrote dt bindings dropping unnecessary compatibles
> (Reported-By: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>)
> - added bindings for two additional boards (cn9131/9132)
> support planned for the coming weeks, mostly serves
> illustrational purposes, to understand cn913x variants
> - cf-pro: add description for LEDs behind DSA switch
> - cf-base: add description for LEDs behind PHYs
> (Reported-By: Andrew Lunn <andrew@lunn.ch>)
> - Link to v1: https://lore.kernel.org/r/20240321-cn9130-som-v1-0-711127a409ae@solid-run.com
>
> ---
> Josua Mayer (4):
> dt-bindings: arm64: marvell: add solidrun cn9130 som based boards
> dt-bindings: arm64: marvell: add solidrun cn9132 CEX-7 evaluation board
> arm64: dts: add description for solidrun cn9130 som and clearfog boards
> arm64: dts: add description for solidrun cn9131 solidwan board
>
> .../bindings/arm/marvell/armada-7k-8k.yaml | 18 +
> arch/arm64/boot/dts/marvell/Makefile | 3 +
> arch/arm64/boot/dts/marvell/cn9130-cf-base.dts | 178 ++++++
> arch/arm64/boot/dts/marvell/cn9130-cf-pro.dts | 375 ++++++++++++
> arch/arm64/boot/dts/marvell/cn9130-cf.dtsi | 197 +++++++
> arch/arm64/boot/dts/marvell/cn9130-sr-som.dtsi | 160 +++++
> arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dts | 643 +++++++++++++++++++++
> 7 files changed, 1574 insertions(+)
> ---
> base-commit: 4cece764965020c22cff7665b18a012006359095
> change-id: 20240318-cn9130-som-848e86acb0ac
>
> Sincerely,
> --
> Josua Mayer <josua@solid-run.com>
>
>
>
My bot found new DTB warnings on the .dts files added or changed in this
series.
Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
are fixed by another series. Ultimately, it is up to the platform
maintainer whether these warnings are acceptable or not. No need to reply
unless the platform maintainer has comments.
If you already ran DT checks and didn't see these error(s), then
make sure dt-schema is up to date:
pip3 install dtschema --upgrade
New warnings running 'make CHECK_DTBS=y marvell/cn9130-cf-base.dtb marvell/cn9130-cf-pro.dtb marvell/cn9131-cf-solidwan.dtb' for 20240502-cn9130-som-v4-0-0a2e2f1c70d8@solid-run.com:
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: ap807: $nodename:0: 'ap807' does not match '^([a-z][a-z0-9\-]+-bus|bus|localbus|soc|axi|ahb|apb)(@.+)?$'
from schema $id: http://devicetree.org/schemas/simple-bus.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: config-space@f0000000: $nodename:0: 'config-space@f0000000' does not match '^([a-z][a-z0-9\-]+-bus|bus|localbus|soc|axi|ahb|apb)(@.+)?$'
from schema $id: http://devicetree.org/schemas/simple-bus.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: config-space@f0000000: timer: {'compatible': ['arm,armv8-timer'], 'interrupts': [[1, 13, 3848], [1, 14, 3848], [1, 11, 3848], [1, 10, 3848]]} should not be valid under {'type': 'object'}
from schema $id: http://devicetree.org/schemas/simple-bus.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: config-space@f0000000: pmu: {'compatible': ['arm,cortex-a72-pmu'], 'interrupt-parent': [[2]], 'interrupts': [[17]]} should not be valid under {'type': 'object'}
from schema $id: http://devicetree.org/schemas/simple-bus.yaml#
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: ap807: $nodename:0: 'ap807' does not match '^([a-z][a-z0-9\-]+-bus|bus|localbus|soc|axi|ahb|apb)(@.+)?$'
from schema $id: http://devicetree.org/schemas/simple-bus.yaml#
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: config-space@f0000000: $nodename:0: 'config-space@f0000000' does not match '^([a-z][a-z0-9\-]+-bus|bus|localbus|soc|axi|ahb|apb)(@.+)?$'
from schema $id: http://devicetree.org/schemas/simple-bus.yaml#
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: config-space@f0000000: timer: {'compatible': ['arm,armv8-timer'], 'interrupts': [[1, 13, 3848], [1, 14, 3848], [1, 11, 3848], [1, 10, 3848]]} should not be valid under {'type': 'object'}
from schema $id: http://devicetree.org/schemas/simple-bus.yaml#
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: config-space@f0000000: pmu: {'compatible': ['arm,cortex-a72-pmu'], 'interrupt-parent': [[2]], 'interrupts': [[17]]} should not be valid under {'type': 'object'}
from schema $id: http://devicetree.org/schemas/simple-bus.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: ap807: $nodename:0: 'ap807' does not match '^([a-z][a-z0-9\-]+-bus|bus|localbus|soc|axi|ahb|apb)(@.+)?$'
from schema $id: http://devicetree.org/schemas/simple-bus.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: config-space@f0000000: $nodename:0: 'config-space@f0000000' does not match '^([a-z][a-z0-9\-]+-bus|bus|localbus|soc|axi|ahb|apb)(@.+)?$'
from schema $id: http://devicetree.org/schemas/simple-bus.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: config-space@f0000000: timer: {'compatible': ['arm,armv8-timer'], 'interrupts': [[1, 13, 3848], [1, 14, 3848], [1, 11, 3848], [1, 10, 3848]]} should not be valid under {'type': 'object'}
from schema $id: http://devicetree.org/schemas/simple-bus.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: config-space@f0000000: pmu: {'compatible': ['arm,cortex-a72-pmu'], 'interrupt-parent': [[2]], 'interrupts': [[17]]} should not be valid under {'type': 'object'}
from schema $id: http://devicetree.org/schemas/simple-bus.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: /ap807/config-space@f0000000/odmi@300000: failed to match any schema with compatible: ['marvell,odmi-controller']
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: /ap807/config-space@f0000000/gicp@3f0040: failed to match any schema with compatible: ['marvell,ap806-gicp']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /ap807/config-space@f0000000/odmi@300000: failed to match any schema with compatible: ['marvell,odmi-controller']
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: /ap807/config-space@f0000000/interrupt-controller@3f0100: failed to match any schema with compatible: ['marvell,armada-8k-pic']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /ap807/config-space@f0000000/gicp@3f0040: failed to match any schema with compatible: ['marvell,ap806-gicp']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /ap807/config-space@f0000000/interrupt-controller@3f0100: failed to match any schema with compatible: ['marvell,armada-8k-pic']
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: /ap807/config-space@f0000000/interrupt-controller@3f0200: failed to match any schema with compatible: ['marvell,ap806-sei']
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: /ap807/config-space@f0000000/xor@400000: failed to match any schema with compatible: ['marvell,armada-7k-xor', 'marvell,xor-v2']
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: /ap807/config-space@f0000000/odmi@300000: failed to match any schema with compatible: ['marvell,odmi-controller']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /ap807/config-space@f0000000/interrupt-controller@3f0200: failed to match any schema with compatible: ['marvell,ap806-sei']
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: /ap807/config-space@f0000000/xor@400000: failed to match any schema with compatible: ['marvell,armada-7k-xor', 'marvell,xor-v2']
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: /ap807/config-space@f0000000/gicp@3f0040: failed to match any schema with compatible: ['marvell,ap806-gicp']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /ap807/config-space@f0000000/xor@400000: failed to match any schema with compatible: ['marvell,armada-7k-xor', 'marvell,xor-v2']
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: /ap807/config-space@f0000000/xor@420000: failed to match any schema with compatible: ['marvell,armada-7k-xor', 'marvell,xor-v2']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /ap807/config-space@f0000000/xor@400000: failed to match any schema with compatible: ['marvell,armada-7k-xor', 'marvell,xor-v2']
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: /ap807/config-space@f0000000/xor@420000: failed to match any schema with compatible: ['marvell,armada-7k-xor', 'marvell,xor-v2']
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: /ap807/config-space@f0000000/interrupt-controller@3f0100: failed to match any schema with compatible: ['marvell,armada-8k-pic']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /ap807/config-space@f0000000/xor@420000: failed to match any schema with compatible: ['marvell,armada-7k-xor', 'marvell,xor-v2']
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: /ap807/config-space@f0000000/xor@440000: failed to match any schema with compatible: ['marvell,armada-7k-xor', 'marvell,xor-v2']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /ap807/config-space@f0000000/xor@420000: failed to match any schema with compatible: ['marvell,armada-7k-xor', 'marvell,xor-v2']
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: /ap807/config-space@f0000000/xor@440000: failed to match any schema with compatible: ['marvell,armada-7k-xor', 'marvell,xor-v2']
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: /ap807/config-space@f0000000/interrupt-controller@3f0200: failed to match any schema with compatible: ['marvell,ap806-sei']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /ap807/config-space@f0000000/xor@440000: failed to match any schema with compatible: ['marvell,armada-7k-xor', 'marvell,xor-v2']
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: /ap807/config-space@f0000000/xor@460000: failed to match any schema with compatible: ['marvell,armada-7k-xor', 'marvell,xor-v2']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /ap807/config-space@f0000000/xor@440000: failed to match any schema with compatible: ['marvell,armada-7k-xor', 'marvell,xor-v2']
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: /ap807/config-space@f0000000/xor@400000: failed to match any schema with compatible: ['marvell,armada-7k-xor', 'marvell,xor-v2']
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: /ap807/config-space@f0000000/xor@460000: failed to match any schema with compatible: ['marvell,armada-7k-xor', 'marvell,xor-v2']
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: /ap807/config-space@f0000000/xor@400000: failed to match any schema with compatible: ['marvell,armada-7k-xor', 'marvell,xor-v2']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /ap807/config-space@f0000000/xor@460000: failed to match any schema with compatible: ['marvell,armada-7k-xor', 'marvell,xor-v2']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /ap807/config-space@f0000000/xor@460000: failed to match any schema with compatible: ['marvell,armada-7k-xor', 'marvell,xor-v2']
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: /ap807/config-space@f0000000/spi@510600: failed to match any schema with compatible: ['marvell,armada-380-spi']
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: /ap807/config-space@f0000000/xor@420000: failed to match any schema with compatible: ['marvell,armada-7k-xor', 'marvell,xor-v2']
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: /ap807/config-space@f0000000/xor@420000: failed to match any schema with compatible: ['marvell,armada-7k-xor', 'marvell,xor-v2']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /ap807/config-space@f0000000/spi@510600: failed to match any schema with compatible: ['marvell,armada-380-spi']
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: /ap807/config-space@f0000000/xor@440000: failed to match any schema with compatible: ['marvell,armada-7k-xor', 'marvell,xor-v2']
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: /ap807/config-space@f0000000/xor@440000: failed to match any schema with compatible: ['marvell,armada-7k-xor', 'marvell,xor-v2']
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: /ap807/config-space@f0000000/xor@460000: failed to match any schema with compatible: ['marvell,armada-7k-xor', 'marvell,xor-v2']
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: /ap807/config-space@f0000000/xor@460000: failed to match any schema with compatible: ['marvell,armada-7k-xor', 'marvell,xor-v2']
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: mmc@6e0000: clocks: [[4, 4]] is too short
from schema $id: http://devicetree.org/schemas/mmc/marvell,xenon-sdhci.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: mmc@6e0000: clock-names: ['core'] is too short
from schema $id: http://devicetree.org/schemas/mmc/marvell,xenon-sdhci.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: mmc@6e0000: Unevaluated properties are not allowed ('dma-coherent' was unexpected)
from schema $id: http://devicetree.org/schemas/mmc/marvell,xenon-sdhci.yaml#
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: mmc@6e0000: clocks: [[4, 4]] is too short
from schema $id: http://devicetree.org/schemas/mmc/marvell,xenon-sdhci.yaml#arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: /ap807/config-space@f0000000/spi@510600: failed to match any schema with compatible: ['marvell,armada-380-spi']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: mmc@6e0000: clock-names: ['core'] is too short
from schema $id: http://devicetree.org/schemas/mmc/marvell,xenon-sdhci.yaml#
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: mmc@6e0000: Unevaluated properties are not allowed ('dma-coherent' was unexpected)
from schema $id: http://devicetree.org/schemas/mmc/marvell,xenon-sdhci.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: system-controller@6f4000: compatible: ['syscon', 'simple-mfd'] is too short
from schema $id: http://devicetree.org/schemas/mfd/syscon.yaml#
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: system-controller@6f4000: compatible: ['syscon', 'simple-mfd'] is too short
from schema $id: http://devicetree.org/schemas/mfd/syscon.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: /ap807/config-space@f0000000/system-controller@6f4000/pinctrl: failed to match any schema with compatible: ['marvell,ap806-pinctrl']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /ap807/config-space@f0000000/system-controller@6f4000/pinctrl: failed to match any schema with compatible: ['marvell,ap806-pinctrl']
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: gpio@1040: Unevaluated properties are not allowed ('gpio-ranges' was unexpected)
from schema $id: http://devicetree.org/schemas/gpio/gpio-mvebu.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: mmc@6e0000: clocks: [[4, 4]] is too short
from schema $id: http://devicetree.org/schemas/mmc/marvell,xenon-sdhci.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: mmc@6e0000: clock-names: ['core'] is too short
from schema $id: http://devicetree.org/schemas/mmc/marvell,xenon-sdhci.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: mmc@6e0000: Unevaluated properties are not allowed ('dma-coherent' was unexpected)
from schema $id: http://devicetree.org/schemas/mmc/marvell,xenon-sdhci.yaml#
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: gpio@1040: Unevaluated properties are not allowed ('gpio-ranges' was unexpected)
from schema $id: http://devicetree.org/schemas/gpio/gpio-mvebu.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: system-controller@6f4000: compatible: ['syscon', 'simple-mfd'] is too short
from schema $id: http://devicetree.org/schemas/mfd/syscon.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: /ap807/config-space@f0000000/system-controller@6f4000/clock: failed to match any schema with compatible: ['marvell,ap807-clock']
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: system-controller@6f8000: compatible: ['syscon', 'simple-mfd'] is too short
from schema $id: http://devicetree.org/schemas/mfd/syscon.yaml#
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /ap807/config-space@f0000000/system-controller@6f4000/clock: failed to match any schema with compatible: ['marvell,ap807-clock']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: system-controller@6f8000: compatible: ['syscon', 'simple-mfd'] is too short
from schema $id: http://devicetree.org/schemas/mfd/syscon.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: /ap807/config-space@f0000000/system-controller@6f4000/pinctrl: failed to match any schema with compatible: ['marvell,ap806-pinctrl']
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: /ap807/config-space@f0000000/system-controller@6f8000/thermal-sensor@80: failed to match any schema with compatible: ['marvell,armada-ap807-thermal']
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: gpio@1040: Unevaluated properties are not allowed ('gpio-ranges' was unexpected)
from schema $id: http://devicetree.org/schemas/gpio/gpio-mvebu.yaml#
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /ap807/config-space@f0000000/system-controller@6f8000/thermal-sensor@80: failed to match any schema with compatible: ['marvell,armada-ap807-thermal']
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: /ap807/config-space@f0000000/system-controller@6f8000/clock-cpu: failed to match any schema with compatible: ['marvell,ap807-cpu-clock']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /ap807/config-space@f0000000/system-controller@6f8000/clock-cpu: failed to match any schema with compatible: ['marvell,ap807-cpu-clock']
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: /ap807/config-space@f0000000/system-controller@6f4000/clock: failed to match any schema with compatible: ['marvell,ap807-clock']
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: system-controller@6f8000: compatible: ['syscon', 'simple-mfd'] is too short
from schema $id: http://devicetree.org/schemas/mfd/syscon.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: /ap807/config-space@f0000000/system-controller@6f8000/thermal-sensor@80: failed to match any schema with compatible: ['marvell,armada-ap807-thermal']
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: /ap807/config-space@f0000000/system-controller@6f8000/clock-cpu: failed to match any schema with compatible: ['marvell,ap807-cpu-clock']
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: cp0: $nodename:0: 'cp0' does not match '^([a-z][a-z0-9\-]+-bus|bus|localbus|soc|axi|ahb|apb)(@.+)?$'
from schema $id: http://devicetree.org/schemas/simple-bus.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: config-space@f2000000: $nodename:0: 'config-space@f2000000' does not match '^([a-z][a-z0-9\-]+-bus|bus|localbus|soc|axi|ahb|apb)(@.+)?$'
from schema $id: http://devicetree.org/schemas/simple-bus.yaml#
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: cp0: $nodename:0: 'cp0' does not match '^([a-z][a-z0-9\-]+-bus|bus|localbus|soc|axi|ahb|apb)(@.+)?$'
from schema $id: http://devicetree.org/schemas/simple-bus.yaml#
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: config-space@f2000000: $nodename:0: 'config-space@f2000000' does not match '^([a-z][a-z0-9\-]+-bus|bus|localbus|soc|axi|ahb|apb)(@.+)?$'
from schema $id: http://devicetree.org/schemas/simple-bus.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: cp0: $nodename:0: 'cp0' does not match '^([a-z][a-z0-9\-]+-bus|bus|localbus|soc|axi|ahb|apb)(@.+)?$'
from schema $id: http://devicetree.org/schemas/simple-bus.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: config-space@f2000000: $nodename:0: 'config-space@f2000000' does not match '^([a-z][a-z0-9\-]+-bus|bus|localbus|soc|axi|ahb|apb)(@.+)?$'
from schema $id: http://devicetree.org/schemas/simple-bus.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: /cp0/config-space@f2000000/phy@120000: failed to match any schema with compatible: ['marvell,comphy-cp110']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /cp0/config-space@f2000000/phy@120000: failed to match any schema with compatible: ['marvell,comphy-cp110']
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: /cp0/config-space@f2000000/phy@120000: failed to match any schema with compatible: ['marvell,comphy-cp110']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /cp0/config-space@f2000000/interrupt-controller@1e0000: failed to match any schema with compatible: ['marvell,cp110-icu']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /cp0/config-space@f2000000/interrupt-controller@1e0000/interrupt-controller@10: failed to match any schema with compatible: ['marvell,cp110-icu-nsr']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /cp0/config-space@f2000000/interrupt-controller@1e0000/interrupt-controller@50: failed to match any schema with compatible: ['marvell,cp110-icu-sei']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: system-controller@440000: compatible: ['syscon', 'simple-mfd'] is too short
from schema $id: http://devicetree.org/schemas/mfd/syscon.yaml#
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /cp0/config-space@f2000000/system-controller@440000/clock: failed to match any schema with compatible: ['marvell,cp110-clock']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: gpio@100: Unevaluated properties are not allowed ('gpio-ranges', 'm2-full-card-power-off-hog', 'pcie0-0-w-disable-hog' were unexpected)
from schema $id: http://devicetree.org/schemas/gpio/gpio-mvebu.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: /cp0/config-space@f2000000/interrupt-controller@1e0000: failed to match any schema with compatible: ['marvell,cp110-icu']
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: /cp0/config-space@f2000000/interrupt-controller@1e0000/interrupt-controller@10: failed to match any schema with compatible: ['marvell,cp110-icu-nsr']
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: /cp0/config-space@f2000000/interrupt-controller@1e0000/interrupt-controller@50: failed to match any schema with compatible: ['marvell,cp110-icu-sei']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: gpio@140: Unevaluated properties are not allowed ('gpio-ranges' was unexpected)
from schema $id: http://devicetree.org/schemas/gpio/gpio-mvebu.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: system-controller@440000: compatible: ['syscon', 'simple-mfd'] is too short
from schema $id: http://devicetree.org/schemas/mfd/syscon.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: /cp0/config-space@f2000000/system-controller@440000/clock: failed to match any schema with compatible: ['marvell,cp110-clock']
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: gpio@100: Unevaluated properties are not allowed ('gpio-ranges', 'sim-select-hog' were unexpected)
from schema $id: http://devicetree.org/schemas/gpio/gpio-mvebu.yaml#
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /cp0/config-space@f2000000/system-controller@440000/pinctrl: failed to match any schema with compatible: ['marvell,cp115-standalone-pinctrl']
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: gpio@140: Unevaluated properties are not allowed ('gpio-ranges' was unexpected)
from schema $id: http://devicetree.org/schemas/gpio/gpio-mvebu.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: /cp0/config-space@f2000000/system-controller@440000/pinctrl: failed to match any schema with compatible: ['marvell,cp115-standalone-pinctrl']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: system-controller@400000: compatible: ['syscon', 'simple-mfd'] is too short
from schema $id: http://devicetree.org/schemas/mfd/syscon.yaml#
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /cp0/config-space@f2000000/system-controller@400000/thermal-sensor@70: failed to match any schema with compatible: ['marvell,armada-cp110-thermal']
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: /cp0/config-space@f2000000/interrupt-controller@1e0000: failed to match any schema with compatible: ['marvell,cp110-icu']
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: system-controller@400000: compatible: ['syscon', 'simple-mfd'] is too short
from schema $id: http://devicetree.org/schemas/mfd/syscon.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: /cp0/config-space@f2000000/interrupt-controller@1e0000/interrupt-controller@10: failed to match any schema with compatible: ['marvell,cp110-icu-nsr']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: usb@500000: Unevaluated properties are not allowed ('dma-coherent', 'dr_mode' were unexpected)
from schema $id: http://devicetree.org/schemas/usb/generic-xhci.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: /cp0/config-space@f2000000/interrupt-controller@1e0000/interrupt-controller@50: failed to match any schema with compatible: ['marvell,cp110-icu-sei']
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: system-controller@440000: compatible: ['syscon', 'simple-mfd'] is too short
from schema $id: http://devicetree.org/schemas/mfd/syscon.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: /cp0/config-space@f2000000/system-controller@400000/thermal-sensor@70: failed to match any schema with compatible: ['marvell,armada-cp110-thermal']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: usb@510000: Unevaluated properties are not allowed ('dma-coherent', 'dr_mode' were unexpected)
from schema $id: http://devicetree.org/schemas/usb/generic-xhci.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: /cp0/config-space@f2000000/system-controller@440000/clock: failed to match any schema with compatible: ['marvell,cp110-clock']
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: gpio@100: Unevaluated properties are not allowed ('gpio-ranges' was unexpected)
from schema $id: http://devicetree.org/schemas/gpio/gpio-mvebu.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: usb@500000: Unevaluated properties are not allowed ('dma-coherent', 'dr_mode', 'vbus-supply' were unexpected)
from schema $id: http://devicetree.org/schemas/usb/generic-xhci.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: usb@510000: Unevaluated properties are not allowed ('dma-coherent', 'dr_mode' were unexpected)
from schema $id: http://devicetree.org/schemas/usb/generic-xhci.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: gpio@140: Unevaluated properties are not allowed ('gpio-ranges' was unexpected)
from schema $id: http://devicetree.org/schemas/gpio/gpio-mvebu.yaml#
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /cp0/config-space@f2000000/xor@6a0000: failed to match any schema with compatible: ['marvell,armada-7k-xor', 'marvell,xor-v2']
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: sata@540000: sata-port@1:
'anyOf' conditional failed, one must be fixed:
'phys' is a required property
'target-supply' is a required property
from schema $id: http://devicetree.org/schemas/ata/ahci-platform.yaml#
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /cp0/config-space@f2000000/xor@6a0000: failed to match any schema with compatible: ['marvell,armada-7k-xor', 'marvell,xor-v2']
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: /cp0/config-space@f2000000/system-controller@440000/pinctrl: failed to match any schema with compatible: ['marvell,cp115-standalone-pinctrl']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /cp0/config-space@f2000000/xor@6c0000: failed to match any schema with compatible: ['marvell,armada-7k-xor', 'marvell,xor-v2']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /cp0/config-space@f2000000/xor@6c0000: failed to match any schema with compatible: ['marvell,armada-7k-xor', 'marvell,xor-v2']
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: /cp0/config-space@f2000000/xor@6a0000: failed to match any schema with compatible: ['marvell,armada-7k-xor', 'marvell,xor-v2']
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: /cp0/config-space@f2000000/xor@6a0000: failed to match any schema with compatible: ['marvell,armada-7k-xor', 'marvell,xor-v2']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /cp0/config-space@f2000000/spi@700600: failed to match any schema with compatible: ['marvell,armada-380-spi']
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: /cp0/config-space@f2000000/xor@6c0000: failed to match any schema with compatible: ['marvell,armada-7k-xor', 'marvell,xor-v2']
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: /cp0/config-space@f2000000/xor@6c0000: failed to match any schema with compatible: ['marvell,armada-7k-xor', 'marvell,xor-v2']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /cp0/config-space@f2000000/spi@700680: failed to match any schema with compatible: ['marvell,armada-380-spi']
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: /cp0/config-space@f2000000/spi@700600: failed to match any schema with compatible: ['marvell,armada-380-spi']
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: /cp0/config-space@f2000000/spi@700680: failed to match any schema with compatible: ['marvell,armada-380-spi']
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: system-controller@400000: compatible: ['syscon', 'simple-mfd'] is too short
from schema $id: http://devicetree.org/schemas/mfd/syscon.yaml#
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: gpio@41: 'gpio-controller' is a required property
from schema $id: http://devicetree.org/schemas/gpio/gpio-pca95xx.yaml#
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: gpio@41: '#gpio-cells' is a required property
from schema $id: http://devicetree.org/schemas/gpio/gpio-pca95xx.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: /cp0/config-space@f2000000/system-controller@400000/thermal-sensor@70: failed to match any schema with compatible: ['marvell,armada-cp110-thermal']
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: usb@500000: Unevaluated properties are not allowed ('dma-coherent', 'dr_mode', 'vbus-supply' were unexpected)
from schema $id: http://devicetree.org/schemas/usb/generic-xhci.yaml#
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: rtc@68: Unevaluated properties are not allowed ('reset-gpios' was unexpected)
from schema $id: http://devicetree.org/schemas/rtc/st,m41t80.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: usb@510000: Unevaluated properties are not allowed ('dma-coherent', 'dr_mode' were unexpected)
from schema $id: http://devicetree.org/schemas/usb/generic-xhci.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: sata@540000: sata-port@1:
'anyOf' conditional failed, one must be fixed:
'phys' is a required property
'target-supply' is a required property
from schema $id: http://devicetree.org/schemas/ata/ahci-platform.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: /cp0/config-space@f2000000/xor@6a0000: failed to match any schema with compatible: ['marvell,armada-7k-xor', 'marvell,xor-v2']
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: /cp0/config-space@f2000000/xor@6a0000: failed to match any schema with compatible: ['marvell,armada-7k-xor', 'marvell,xor-v2']
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: /cp0/config-space@f2000000/xor@6c0000: failed to match any schema with compatible: ['marvell,armada-7k-xor', 'marvell,xor-v2']
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: /cp0/config-space@f2000000/xor@6c0000: failed to match any schema with compatible: ['marvell,armada-7k-xor', 'marvell,xor-v2']
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: /cp0/config-space@f2000000/spi@700600: failed to match any schema with compatible: ['marvell,armada-380-spi']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /cp0/config-space@f2000000/trng@760000: failed to match any schema with compatible: ['marvell,armada-8k-rng', 'inside-secure,safexcel-eip76']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: mmc@780000: Unevaluated properties are not allowed ('dma-coherent' was unexpected)
from schema $id: http://devicetree.org/schemas/mmc/marvell,xenon-sdhci.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: /cp0/config-space@f2000000/spi@700680: failed to match any schema with compatible: ['marvell,armada-380-spi']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: crypto@800000: 'dma-coherent' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/crypto/inside-secure,safexcel.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: /cp0/config-space@f2000000/trng@760000: failed to match any schema with compatible: ['marvell,armada-8k-rng', 'inside-secure,safexcel-eip76']
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: mmc@780000: Unevaluated properties are not allowed ('dma-coherent' was unexpected)
from schema $id: http://devicetree.org/schemas/mmc/marvell,xenon-sdhci.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: crypto@800000: 'dma-coherent' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/crypto/inside-secure,safexcel.yaml#
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /cp0/pcie@f2600000: failed to match any schema with compatible: ['marvell,armada8k-pcie', 'snps,dw-pcie']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /cp0/pcie@f2620000: failed to match any schema with compatible: ['marvell,armada8k-pcie', 'snps,dw-pcie']
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: /cp0/pcie@f2600000: failed to match any schema with compatible: ['marvell,armada8k-pcie', 'snps,dw-pcie']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /cp0/pcie@f2640000: failed to match any schema with compatible: ['marvell,armada8k-pcie', 'snps,dw-pcie']
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: /cp0/pcie@f2620000: failed to match any schema with compatible: ['marvell,armada8k-pcie', 'snps,dw-pcie']
arch/arm64/boot/dts/marvell/cn9130-cf-base.dtb: /cp0/pcie@f2640000: failed to match any schema with compatible: ['marvell,armada8k-pcie', 'snps,dw-pcie']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: cp1: $nodename:0: 'cp1' does not match '^([a-z][a-z0-9\-]+-bus|bus|localbus|soc|axi|ahb|apb)(@.+)?$'
from schema $id: http://devicetree.org/schemas/simple-bus.yaml#
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: config-space@f4000000: $nodename:0: 'config-space@f4000000' does not match '^([a-z][a-z0-9\-]+-bus|bus|localbus|soc|axi|ahb|apb)(@.+)?$'
from schema $id: http://devicetree.org/schemas/simple-bus.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: /cp0/config-space@f2000000/trng@760000: failed to match any schema with compatible: ['marvell,armada-8k-rng', 'inside-secure,safexcel-eip76']
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: mmc@780000: Unevaluated properties are not allowed ('dma-coherent' was unexpected)
from schema $id: http://devicetree.org/schemas/mmc/marvell,xenon-sdhci.yaml#
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /cp1/config-space@f4000000/phy@120000: failed to match any schema with compatible: ['marvell,comphy-cp110']
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: crypto@800000: 'dma-coherent' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/crypto/inside-secure,safexcel.yaml#
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: /cp0/pcie@f2600000: failed to match any schema with compatible: ['marvell,armada8k-pcie', 'snps,dw-pcie']
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: /cp0/pcie@f2620000: failed to match any schema with compatible: ['marvell,armada8k-pcie', 'snps,dw-pcie']
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dtb: /cp0/pcie@f2640000: failed to match any schema with compatible: ['marvell,armada8k-pcie', 'snps,dw-pcie']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /cp1/config-space@f4000000/interrupt-controller@1e0000: failed to match any schema with compatible: ['marvell,cp110-icu']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /cp1/config-space@f4000000/interrupt-controller@1e0000/interrupt-controller@10: failed to match any schema with compatible: ['marvell,cp110-icu-nsr']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /cp1/config-space@f4000000/interrupt-controller@1e0000/interrupt-controller@50: failed to match any schema with compatible: ['marvell,cp110-icu-sei']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: system-controller@440000: compatible: ['syscon', 'simple-mfd'] is too short
from schema $id: http://devicetree.org/schemas/mfd/syscon.yaml#
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /cp1/config-space@f4000000/system-controller@440000/clock: failed to match any schema with compatible: ['marvell,cp110-clock']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: gpio@100: Unevaluated properties are not allowed ('gpio-ranges', 'm2-full-card-power-off-hog-0', 'm2-full-card-power-off-hog-1' were unexpected)
from schema $id: http://devicetree.org/schemas/gpio/gpio-mvebu.yaml#
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: gpio@140: Unevaluated properties are not allowed ('gpio-ranges' was unexpected)
from schema $id: http://devicetree.org/schemas/gpio/gpio-mvebu.yaml#
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /cp1/config-space@f4000000/system-controller@440000/pinctrl: failed to match any schema with compatible: ['marvell,cp115-standalone-pinctrl']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: system-controller@400000: compatible: ['syscon', 'simple-mfd'] is too short
from schema $id: http://devicetree.org/schemas/mfd/syscon.yaml#
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /cp1/config-space@f4000000/system-controller@400000/thermal-sensor@70: failed to match any schema with compatible: ['marvell,armada-cp110-thermal']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: usb@500000: Unevaluated properties are not allowed ('dma-coherent', 'dr_mode' were unexpected)
from schema $id: http://devicetree.org/schemas/usb/generic-xhci.yaml#
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: usb@510000: Unevaluated properties are not allowed ('dma-coherent', 'dr_mode' were unexpected)
from schema $id: http://devicetree.org/schemas/usb/generic-xhci.yaml#
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: sata@540000: sata-port@0:
'anyOf' conditional failed, one must be fixed:
'phys' is a required property
'target-supply' is a required property
from schema $id: http://devicetree.org/schemas/ata/ahci-platform.yaml#
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /cp1/config-space@f4000000/xor@6a0000: failed to match any schema with compatible: ['marvell,armada-7k-xor', 'marvell,xor-v2']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /cp1/config-space@f4000000/xor@6a0000: failed to match any schema with compatible: ['marvell,armada-7k-xor', 'marvell,xor-v2']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /cp1/config-space@f4000000/xor@6c0000: failed to match any schema with compatible: ['marvell,armada-7k-xor', 'marvell,xor-v2']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /cp1/config-space@f4000000/xor@6c0000: failed to match any schema with compatible: ['marvell,armada-7k-xor', 'marvell,xor-v2']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /cp1/config-space@f4000000/spi@700600: failed to match any schema with compatible: ['marvell,armada-380-spi']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /cp1/config-space@f4000000/spi@700680: failed to match any schema with compatible: ['marvell,armada-380-spi']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /cp1/config-space@f4000000/trng@760000: failed to match any schema with compatible: ['marvell,armada-8k-rng', 'inside-secure,safexcel-eip76']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: crypto@800000: 'dma-coherent' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/crypto/inside-secure,safexcel.yaml#
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /cp1/pcie@f4600000: failed to match any schema with compatible: ['marvell,armada8k-pcie', 'snps,dw-pcie']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /cp1/pcie@f4620000: failed to match any schema with compatible: ['marvell,armada8k-pcie', 'snps,dw-pcie']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: /cp1/pcie@f4640000: failed to match any schema with compatible: ['marvell,armada8k-pcie', 'snps,dw-pcie']
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: sfp-0: 'los-gpio', 'mod-def0-gpio', 'tx-disable-gpio', 'tx-fault-gpio' do not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/net/sff,sfp.yaml#
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dtb: sfp-1: 'los-gpio', 'mod-def0-gpio', 'tx-disable-gpio', 'tx-fault-gpio' do not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/net/sff,sfp.yaml#
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [PATCH v4 4/4] arm64: dts: add description for solidrun cn9131 solidwan board
2024-05-02 12:32 ` [PATCH v4 4/4] arm64: dts: add description for solidrun cn9131 solidwan board Josua Mayer
@ 2024-05-02 15:20 ` Rob Herring
2024-05-02 17:24 ` Josua Mayer
2024-05-02 17:35 ` Josua Mayer
1 sibling, 1 reply; 11+ messages in thread
From: Rob Herring @ 2024-05-02 15:20 UTC (permalink / raw)
To: Josua Mayer
Cc: Andrew Lunn, Gregory Clement, Sebastian Hesselbarth,
Krzysztof Kozlowski, Conor Dooley, Yazan Shhady, linux-arm-kernel,
devicetree, linux-kernel
On Thu, May 2, 2024 at 7:32 AM Josua Mayer <josua@solid-run.com> wrote:
>
> Add description for the SolidRun CN9131 SolidWAN, based on CN9130 SoM
> with an extra communication processor on the carrier board.
>
> This board differentiates itself from CN9130 Clearfog by providing
> additional SoC native network interfaces and pci buses:
> 2x 10Gbps SFP+
> 4x 1Gbps RJ45
> 1x miniPCI-E
> 1x m.2 b-key with sata, usb-2.0 and usb-3.0
> 1x m.2 m-key with pcie and usb-2.0
> 1x m.2 b-key with pcie, usb-2.0, usb-3.0 and 2x sim slots
> 1x mpcie with pcie only
> 2x type-a usb-2.0/3.0
>
> Signed-off-by: Josua Mayer <josua@solid-run.com>
> ---
> arch/arm64/boot/dts/marvell/Makefile | 1 +
> arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dts | 643 +++++++++++++++++++++
> 2 files changed, 644 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
> index 019f2251d696..16f9d7156d9f 100644
> --- a/arch/arm64/boot/dts/marvell/Makefile
> +++ b/arch/arm64/boot/dts/marvell/Makefile
> @@ -30,3 +30,4 @@ dtb-$(CONFIG_ARCH_MVEBU) += ac5x-rd-carrier-cn9131.dtb
> dtb-$(CONFIG_ARCH_MVEBU) += ac5-98dx35xx-rd.dtb
> dtb-$(CONFIG_ARCH_MVEBU) += cn9130-cf-base.dtb
> dtb-$(CONFIG_ARCH_MVEBU) += cn9130-cf-pro.dtb
> +dtb-$(CONFIG_ARCH_MVEBU) += cn9131-cf-solidwan.dtb
> diff --git a/arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dts b/arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dts
> new file mode 100644
> index 000000000000..a63a8961bad0
> --- /dev/null
> +++ b/arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dts
> @@ -0,0 +1,643 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright (C) 2024 Josua Mayer <josua@solid-run.com>
> + *
> + * DTS for SolidRun CN9130 Clearfog Base.
> + *
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/leds/common.h>
> +
> +#include "cn9130.dtsi"
> +#include "cn9130-sr-som.dtsi"
> +
> +/*
> + * Instantiate the external CP115
> + */
> +
> +#define CP11X_NAME cp1
> +#define CP11X_BASE f4000000
> +#define CP11X_PCIEx_MEM_BASE(iface) (0xe2000000 + (iface * 0x1000000))
> +#define CP11X_PCIEx_MEM_SIZE(iface) 0xf00000
> +#define CP11X_PCIE0_BASE f4600000
> +#define CP11X_PCIE1_BASE f4620000
> +#define CP11X_PCIE2_BASE f4640000
> +
> +#include "armada-cp115.dtsi"
> +
> +#undef CP11X_NAME
> +#undef CP11X_BASE
> +#undef CP11X_PCIEx_MEM_BASE
> +#undef CP11X_PCIEx_MEM_SIZE
> +#undef CP11X_PCIE0_BASE
> +#undef CP11X_PCIE1_BASE
> +#undef CP11X_PCIE2_BASE
> +
> +/ {
> + model = "SolidRun CN9131 SolidWAN";
> + compatible = "solidrun,cn9131-solidwan",
> + "solidrun,cn9130-sr-som", "marvell,cn9130";
> +
> + aliases {
> + ethernet0 = &cp1_eth1;
> + ethernet1 = &cp1_eth2;
> + ethernet2 = &cp0_eth1;
> + ethernet3 = &cp0_eth2;
> + ethernet4 = &cp0_eth0;
> + ethernet5 = &cp1_eth0;
> + gpio0 = &ap_gpio;
> + gpio1 = &cp0_gpio1;
> + gpio2 = &cp0_gpio2;
> + gpio3 = &cp1_gpio1;
> + gpio4 = &cp1_gpio2;
> + gpio5 = &expander0;
> + i2c0 = &cp0_i2c0;
> + i2c1 = &cp0_i2c1;
> + i2c2 = &cp1_i2c1;
> + mmc0 = &ap_sdhci0;
> + mmc1 = &cp0_sdhci0;
> + rtc0 = &cp0_rtc;
> + rtc1 = &carrier_rtc;
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&cp0_led_pins &cp1_led_pins>;
> +
> + /* for sfp-1 (J42) */
> + led-sfp1-activity {
> + label = "sfp1:green";
> + gpios = <&cp0_gpio1 7 GPIO_ACTIVE_HIGH>;
> + };
> +
> + /* for sfp-1 (J42) */
> + led-sfp1-link {
> + label = "sfp1:yellow";
> + gpios = <&cp0_gpio1 4 GPIO_ACTIVE_HIGH>;
> + };
> +
> + /* (J28) */
> + led-sfp0-activity {
> + label = "sfp0:green";
> + gpios = <&cp1_gpio2 22 GPIO_ACTIVE_HIGH>;
> + };
> +
> + /* (J28) */
> + led-sfp0-link {
> + label = "sfp0:yellow";
> + gpios = <&cp1_gpio2 23 GPIO_ACTIVE_HIGH>;
> + };
> + };
> +
> + /* Type-A port on J53 */
> + reg_usb_a_vbus0: regulator-usb-a-vbus0 {
> + compatible = "regulator-fixed";
> + pinctrl-0 = <&cp0_reg_usb_a_vbus0_pins>;
> + pinctrl-names = "default";
> + regulator-name = "vbus0";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-oc-protection-microamp = <1000000>;
> + gpio = <&cp0_gpio1 27 GPIO_ACTIVE_HIGH>;
"gpio" is deprecated.
> + enable-active-high;
> + regulator-always-on;
> + };
> +
> + reg_usb_a_vbus1: regulator-usb-a-vbus1 {
> + compatible = "regulator-fixed";
> + pinctrl-0 = <&cp0_reg_usb_a_vbus1_pins>;
> + pinctrl-names = "default";
> + regulator-name = "vbus1";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-oc-protection-microamp = <1000000>;
> + gpio = <&cp0_gpio1 28 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-always-on;
> + };
> +
> + sfp0: sfp-0 {
> + compatible = "sff,sfp";
> + pinctrl-0 = <&cp0_sfp0_pins>;
> + pinctrl-names = "default";
> + i2c-bus = <&cp0_i2c1>;
> + los-gpio = <&cp0_gpio2 2 GPIO_ACTIVE_HIGH>;
> + mod-def0-gpio = <&cp0_gpio2 0 GPIO_ACTIVE_LOW>;
> + tx-disable-gpio = <&cp0_gpio2 1 GPIO_ACTIVE_HIGH>;
> + tx-fault-gpio = <&cp0_gpio1 31 GPIO_ACTIVE_HIGH>;
As is "-gpio" suffix. These are all pointed out with 'dtbs_check'
which I sent a report on v3. I haven't checked what else from that you
ignored... I don't expect warnings inherited from the SoC .dtsi to be
fixed in this series, but certainly the board level ones. Yes, it's
hard to pick out those, but that's the Marvell folks fault for not
fixing SoC level warnings.
Rob
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [PATCH v4 4/4] arm64: dts: add description for solidrun cn9131 solidwan board
2024-05-02 15:20 ` Rob Herring
@ 2024-05-02 17:24 ` Josua Mayer
0 siblings, 0 replies; 11+ messages in thread
From: Josua Mayer @ 2024-05-02 17:24 UTC (permalink / raw)
To: Rob Herring
Cc: Andrew Lunn, Gregory Clement, Sebastian Hesselbarth,
Krzysztof Kozlowski, Conor Dooley, Yazan Shhady,
linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org
Am 02.05.24 um 17:20 schrieb Rob Herring:
> On Thu, May 2, 2024 at 7:32 AM Josua Mayer <josua@solid-run.com> wrote:
>> Add description for the SolidRun CN9131 SolidWAN, based on CN9130 SoM
>> with an extra communication processor on the carrier board.
>>
>> This board differentiates itself from CN9130 Clearfog by providing
>> additional SoC native network interfaces and pci buses:
>> 2x 10Gbps SFP+
>> 4x 1Gbps RJ45
>> 1x miniPCI-E
>> 1x m.2 b-key with sata, usb-2.0 and usb-3.0
>> 1x m.2 m-key with pcie and usb-2.0
>> 1x m.2 b-key with pcie, usb-2.0, usb-3.0 and 2x sim slots
>> 1x mpcie with pcie only
>> 2x type-a usb-2.0/3.0
>>
>> Signed-off-by: Josua Mayer <josua@solid-run.com>
cut
>> + /* Type-A port on J53 */
>> + reg_usb_a_vbus0: regulator-usb-a-vbus0 {
>> + compatible = "regulator-fixed";
>> + pinctrl-0 = <&cp0_reg_usb_a_vbus0_pins>;
>> + pinctrl-names = "default";
>> + regulator-name = "vbus0";
>> + regulator-min-microvolt = <5000000>;
>> + regulator-max-microvolt = <5000000>;
>> + regulator-oc-protection-microamp = <1000000>;
>> + gpio = <&cp0_gpio1 27 GPIO_ACTIVE_HIGH>;
> "gpio" is deprecated.
Thank you for pointing this out.
I did actually think about it while reading the bindings,
and failed to figure this out. "gpio" occured to me as more correct:
gpio:
description: gpio to use for enable control
maxItems: 1
gpios:
maxItems: 1
I could of course have checked git log, and found
regulator: dt-bindings: fixed-regulator:allow gpios property
by Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
with the explanation:
"'gpios' is in general preferred"
>
>> + enable-active-high;
>> + regulator-always-on;
>> + };
>> +
>> + reg_usb_a_vbus1: regulator-usb-a-vbus1 {
>> + compatible = "regulator-fixed";
>> + pinctrl-0 = <&cp0_reg_usb_a_vbus1_pins>;
>> + pinctrl-names = "default";
>> + regulator-name = "vbus1";
>> + regulator-min-microvolt = <5000000>;
>> + regulator-max-microvolt = <5000000>;
>> + regulator-oc-protection-microamp = <1000000>;
>> + gpio = <&cp0_gpio1 28 GPIO_ACTIVE_HIGH>;
>> + enable-active-high;
>> + regulator-always-on;
>> + };
>> +
>> + sfp0: sfp-0 {
>> + compatible = "sff,sfp";
>> + pinctrl-0 = <&cp0_sfp0_pins>;
>> + pinctrl-names = "default";
>> + i2c-bus = <&cp0_i2c1>;
>> + los-gpio = <&cp0_gpio2 2 GPIO_ACTIVE_HIGH>;
>> + mod-def0-gpio = <&cp0_gpio2 0 GPIO_ACTIVE_LOW>;
>> + tx-disable-gpio = <&cp0_gpio2 1 GPIO_ACTIVE_HIGH>;
>> + tx-fault-gpio = <&cp0_gpio1 31 GPIO_ACTIVE_HIGH>;
> As is "-gpio" suffix. These are all pointed out with 'dtbs_check'
> which I sent a report on v3. I haven't checked what else from that you
> ignored... I don't expect warnings inherited from the SoC .dtsi to be
> fixed in this series, but certainly the board level ones. Yes, it's
> hard to pick out those, but that's the Marvell folks fault for not
> fixing SoC level warnings.
You are right, they were clearly pointed out by your bot
and I missed them. They will be corrected in v5.
Thanks
- Josua Mayer
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [PATCH v4 4/4] arm64: dts: add description for solidrun cn9131 solidwan board
2024-05-02 12:32 ` [PATCH v4 4/4] arm64: dts: add description for solidrun cn9131 solidwan board Josua Mayer
2024-05-02 15:20 ` Rob Herring
@ 2024-05-02 17:35 ` Josua Mayer
2024-05-03 13:24 ` Rob Herring
1 sibling, 1 reply; 11+ messages in thread
From: Josua Mayer @ 2024-05-02 17:35 UTC (permalink / raw)
To: Andrew Lunn, Gregory Clement, Sebastian Hesselbarth, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Rob Herring
Cc: Yazan Shhady, linux-arm-kernel@lists.infradead.org,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org
Am 02.05.24 um 14:32 schrieb Josua Mayer:
> Add description for the SolidRun CN9131 SolidWAN, based on CN9130 SoM
> with an extra communication processor on the carrier board.
>
> This board differentiates itself from CN9130 Clearfog by providing
> additional SoC native network interfaces and pci buses:
> 2x 10Gbps SFP+
> 4x 1Gbps RJ45
> 1x miniPCI-E
> 1x m.2 b-key with sata, usb-2.0 and usb-3.0
> 1x m.2 m-key with pcie and usb-2.0
> 1x m.2 b-key with pcie, usb-2.0, usb-3.0 and 2x sim slots
> 1x mpcie with pcie only
> 2x type-a usb-2.0/3.0
>
> Signed-off-by: Josua Mayer <josua@solid-run.com>
> ---
> arch/arm64/boot/dts/marvell/Makefile | 1 +
> arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dts | 643 +++++++++++++++++++++
> 2 files changed, 644 insertions(+)
>
cut
> + /* Type-A port on J53 */
> + reg_usb_a_vbus0: regulator-usb-a-vbus0 {
> + compatible = "regulator-fixed";
> + pinctrl-0 = <&cp0_reg_usb_a_vbus0_pins>;
> + pinctrl-names = "default";
> + regulator-name = "vbus0";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-oc-protection-microamp = <1000000>;
Is it correct to specify over-current protection for a regulator-fixed? It causes kernel messages:
[ 7.988337] vbus0: IC does not support requested over-current limits [ 7.994756] vbus0: IC does not support requested over voltage limits [ 7.998796] vbus1: IC does not support requested over-current limits ...
The reason I put the property was that the 1A limit is a property of the regulator component (NCP380-1.0A). Maybe that is the wrong property?
It also generates an interrupt for which I found no suitable description.
> + gpio = <&cp0_gpio1 27 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-always-on;
> + };
> +
> + reg_usb_a_vbus1: regulator-usb-a-vbus1 {
> + compatible = "regulator-fixed";
> + pinctrl-0 = <&cp0_reg_usb_a_vbus1_pins>;
> + pinctrl-names = "default";
> + regulator-name = "vbus1";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-oc-protection-microamp = <1000000>;
same here
> + gpio = <&cp0_gpio1 28 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-always-on;
> + };
> +
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [PATCH v4 4/4] arm64: dts: add description for solidrun cn9131 solidwan board
2024-05-02 17:35 ` Josua Mayer
@ 2024-05-03 13:24 ` Rob Herring
2024-05-05 10:27 ` Josua Mayer
0 siblings, 1 reply; 11+ messages in thread
From: Rob Herring @ 2024-05-03 13:24 UTC (permalink / raw)
To: Josua Mayer
Cc: Andrew Lunn, Gregory Clement, Sebastian Hesselbarth,
Krzysztof Kozlowski, Conor Dooley, Yazan Shhady,
linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org
On Thu, May 02, 2024 at 05:35:44PM +0000, Josua Mayer wrote:
> Am 02.05.24 um 14:32 schrieb Josua Mayer:
> > Add description for the SolidRun CN9131 SolidWAN, based on CN9130 SoM
> > with an extra communication processor on the carrier board.
> >
> > This board differentiates itself from CN9130 Clearfog by providing
> > additional SoC native network interfaces and pci buses:
> > 2x 10Gbps SFP+
> > 4x 1Gbps RJ45
> > 1x miniPCI-E
> > 1x m.2 b-key with sata, usb-2.0 and usb-3.0
> > 1x m.2 m-key with pcie and usb-2.0
> > 1x m.2 b-key with pcie, usb-2.0, usb-3.0 and 2x sim slots
> > 1x mpcie with pcie only
> > 2x type-a usb-2.0/3.0
> >
> > Signed-off-by: Josua Mayer <josua@solid-run.com>
> > ---
> > arch/arm64/boot/dts/marvell/Makefile | 1 +
> > arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dts | 643 +++++++++++++++++++++
> > 2 files changed, 644 insertions(+)
> >
> cut
> > + /* Type-A port on J53 */
> > + reg_usb_a_vbus0: regulator-usb-a-vbus0 {
> > + compatible = "regulator-fixed";
> > + pinctrl-0 = <&cp0_reg_usb_a_vbus0_pins>;
> > + pinctrl-names = "default";
> > + regulator-name = "vbus0";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + regulator-oc-protection-microamp = <1000000>;
>
> Is it correct to specify over-current protection for a
> regulator-fixed? It causes kernel messages:
>
> [ 7.988337] vbus0: IC does not support requested over-current limits
> [ 7.994756] vbus0: IC does not support requested over voltage limits
> [ 7.998796] vbus1: IC does not support requested over-current limits
> ...
Seems like you have your answer...
>
> The reason I put the property was that the 1A limit is a property of
> the regulator component (NCP380-1.0A). Maybe that is the wrong property?
>
> It also generates an interrupt for which I found no suitable description.
Then you should describe the actual device because it is not just a
regulator-fixed. I suppose we could consider adding an interrupt to
regulator-fixed, but then its function can only be for (presumably)
over-current. Even details on how to handle it could vary as well.
Rob
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [PATCH v4 4/4] arm64: dts: add description for solidrun cn9131 solidwan board
2024-05-03 13:24 ` Rob Herring
@ 2024-05-05 10:27 ` Josua Mayer
0 siblings, 0 replies; 11+ messages in thread
From: Josua Mayer @ 2024-05-05 10:27 UTC (permalink / raw)
To: Rob Herring
Cc: Andrew Lunn, Gregory Clement, Sebastian Hesselbarth,
Krzysztof Kozlowski, Conor Dooley, Yazan Shhady,
linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org
Am 03.05.24 um 15:24 schrieb Rob Herring:
> On Thu, May 02, 2024 at 05:35:44PM +0000, Josua Mayer wrote:
>> Am 02.05.24 um 14:32 schrieb Josua Mayer:
>>> Add description for the SolidRun CN9131 SolidWAN, based on CN9130 SoM
>>> with an extra communication processor on the carrier board.
>>>
>>> This board differentiates itself from CN9130 Clearfog by providing
>>> additional SoC native network interfaces and pci buses:
>>> 2x 10Gbps SFP+
>>> 4x 1Gbps RJ45
>>> 1x miniPCI-E
>>> 1x m.2 b-key with sata, usb-2.0 and usb-3.0
>>> 1x m.2 m-key with pcie and usb-2.0
>>> 1x m.2 b-key with pcie, usb-2.0, usb-3.0 and 2x sim slots
>>> 1x mpcie with pcie only
>>> 2x type-a usb-2.0/3.0
>>>
>>> Signed-off-by: Josua Mayer <josua@solid-run.com>
>>> ---
>>> arch/arm64/boot/dts/marvell/Makefile | 1 +
>>> arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dts | 643 +++++++++++++++++++++
>>> 2 files changed, 644 insertions(+)
>>>
>> cut
>>> + /* Type-A port on J53 */
>>> + reg_usb_a_vbus0: regulator-usb-a-vbus0 {
>>> + compatible = "regulator-fixed";
>>> + pinctrl-0 = <&cp0_reg_usb_a_vbus0_pins>;
>>> + pinctrl-names = "default";
>>> + regulator-name = "vbus0";
>>> + regulator-min-microvolt = <5000000>;
>>> + regulator-max-microvolt = <5000000>;
>>> + regulator-oc-protection-microamp = <1000000>;
>> Is it correct to specify over-current protection for a
>> regulator-fixed? It causes kernel messages:
>>
>> [ 7.988337] vbus0: IC does not support requested over-current limits
>> [ 7.994756] vbus0: IC does not support requested over voltage limits
>> [ 7.998796] vbus1: IC does not support requested over-current limits
>> ...
> Seems like you have your answer...
Okay, I will remove those for v5.
>
>> The reason I put the property was that the 1A limit is a property of
>> the regulator component (NCP380-1.0A). Maybe that is the wrong property?
>>
>> It also generates an interrupt for which I found no suitable description.
> Then you should describe the actual device because it is not just a
> regulator-fixed. I suppose we could consider adding an interrupt to
> regulator-fixed, but then its function can only be for (presumably)
> over-current. Even details on how to handle it could vary as well.
Beyond signaling to userspace I see no actions that can be taken.
The part operates autonomously, including turning off the output
temporarily, and merely signals any errors (e.g. over-current,
over-heating) on the interrupt line.
I would actually prefer to stick with fixed-regulator.
The interrupt could be very broad, for any regulator fault.
But I could also just omit it.
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 11+ messages in thread
end of thread, other threads:[~2024-05-05 10:28 UTC | newest]
Thread overview: 11+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2024-05-02 12:32 [PATCH v4 0/4] arm64: dts: add description for solidrun cn9130 som and clearfog boards Josua Mayer
2024-05-02 12:32 ` [PATCH v4 1/4] dt-bindings: arm64: marvell: add solidrun cn9130 som based boards Josua Mayer
2024-05-02 12:32 ` [PATCH v4 2/4] dt-bindings: arm64: marvell: add solidrun cn9132 CEX-7 evaluation board Josua Mayer
2024-05-02 12:32 ` [PATCH v4 3/4] arm64: dts: add description for solidrun cn9130 som and clearfog boards Josua Mayer
2024-05-02 12:32 ` [PATCH v4 4/4] arm64: dts: add description for solidrun cn9131 solidwan board Josua Mayer
2024-05-02 15:20 ` Rob Herring
2024-05-02 17:24 ` Josua Mayer
2024-05-02 17:35 ` Josua Mayer
2024-05-03 13:24 ` Rob Herring
2024-05-05 10:27 ` Josua Mayer
2024-05-02 15:08 ` [PATCH v4 0/4] arm64: dts: add description for solidrun cn9130 som and clearfog boards Rob Herring (Arm)
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).