From: Dmitry Torokhov <dmitry.torokhov@gmail.com>
To: Haojian Zhuang <haojian.zhuang@gmail.com>,
Daniel Mack <daniel@zonque.org>,
Robert Jarzmik <robert.jarzmik@free.fr>,
Arnd Bergmann <arnd@arndb.de>,
Linus Walleij <linus.walleij@linaro.org>,
soc@kernel.org
Cc: linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org
Subject: [PATCH 00/10] ARM: pxa: use software nodes/properties for GPIOs
Date: Fri, 28 Jun 2024 11:08:40 -0700 [thread overview]
Message-ID: <20240628180852.1738922-1-dmitry.torokhov@gmail.com> (raw)
This series converts legacy pxa boards (spitz, gumstix) to use software
nodes/properties to describe various GPIOs instead of relying on GPIO
lookup tables. The benefit is that structure and behavior is closer to
DT-described GPIOs.
The very first patch ("ARM: spitz: fix GPIO assignment for backlight")
is actually a fix that IMO should be applied sooner rather than later,
the rest of patches are enhancements. The reason it is sent with the
rest of the series is that later changes contextually depend on it.
The last patch ("ARM: spitz: Use software nodes for the ADS7846
touchscreen") soft-depends on corresponding changes by Linus Walleij to
the ads7846 driver in input tree. It compiles without it, but the device
will not sync with display refreshes. I have created an immutable branch
(branched from v6.9) at:
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input.git ib/ads7846-hsync
in case you wish to pull it in.
Regretfully it was only compiled as I do not have access to the relevant
hardware.
Dmitry Torokhov (8):
ARM: spitz: fix GPIO assignment for backlight
ARM: pxa: consolidate GPIO chip platform data
ARM: pxa/gumstix: convert vbus gpio to use software nodes
ARM: spitz: Simplify instantiating SPI controller
ARM: spitz: Use software nodes to describe audio GPIOs
ARM: spitz: Use software nodes to describe LCD GPIOs
ARM: spitz: Use software nodes to describe MMC GPIOs
ARM: spitz: Use software nodes to describe LED GPIOs
Linus Walleij (2):
ARM: spitz: Use software nodes to describe SPI CS lines
ARM: spitz: Use software nodes for the ADS7846 touchscreen
arch/arm/mach-pxa/devices.c | 53 +++--
arch/arm/mach-pxa/devices.h | 5 +-
arch/arm/mach-pxa/gumstix.c | 24 +-
arch/arm/mach-pxa/pxa25x.c | 8 +-
arch/arm/mach-pxa/pxa27x.c | 9 +-
arch/arm/mach-pxa/spitz.c | 284 ++++++++++++-----------
include/linux/platform_data/mmc-pxamci.h | 4 +-
7 files changed, 208 insertions(+), 179 deletions(-)
Thanks.
--
2.45.2.803.g4e1b14247a-goog
next reply other threads:[~2024-06-28 18:09 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-06-28 18:08 Dmitry Torokhov [this message]
2024-06-28 18:08 ` [PATCH 01/10] ARM: spitz: fix GPIO assignment for backlight Dmitry Torokhov
2024-06-28 18:08 ` [PATCH 02/10] ARM: pxa: consolidate GPIO chip platform data Dmitry Torokhov
2024-06-28 18:08 ` [PATCH 03/10] ARM: pxa/gumstix: convert vbus gpio to use software nodes Dmitry Torokhov
2024-08-06 7:19 ` Arnd Bergmann
2024-08-06 16:58 ` Dmitry Torokhov
2024-08-06 20:36 ` Arnd Bergmann
2024-06-28 18:08 ` [PATCH 04/10] ARM: spitz: Simplify instantiating SPI controller Dmitry Torokhov
2024-06-28 18:08 ` [PATCH 05/10] ARM: spitz: Use software nodes to describe SPI CS lines Dmitry Torokhov
2024-06-28 18:08 ` [PATCH 06/10] ARM: spitz: Use software nodes to describe audio GPIOs Dmitry Torokhov
2024-06-28 18:08 ` [PATCH 07/10] ARM: spitz: Use software nodes to describe LCD GPIOs Dmitry Torokhov
2024-06-28 18:08 ` [PATCH 08/10] ARM: spitz: Use software nodes to describe MMC GPIOs Dmitry Torokhov
2024-06-28 18:08 ` [PATCH 09/10] ARM: spitz: Use software nodes to describe LED GPIOs Dmitry Torokhov
2024-06-28 18:08 ` [PATCH 10/10] ARM: spitz: Use software nodes for the ADS7846 touchscreen Dmitry Torokhov
2024-06-28 20:59 ` [PATCH 00/10] ARM: pxa: use software nodes/properties for GPIOs Arnd Bergmann
2024-06-28 21:08 ` Arnd Bergmann
2024-06-28 21:44 ` Dmitry Torokhov
2024-06-29 7:34 ` Arnd Bergmann
2024-06-30 8:07 ` Linus Walleij
2024-06-30 8:41 ` Arnd Bergmann
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20240628180852.1738922-1-dmitry.torokhov@gmail.com \
--to=dmitry.torokhov@gmail.com \
--cc=arnd@arndb.de \
--cc=daniel@zonque.org \
--cc=haojian.zhuang@gmail.com \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robert.jarzmik@free.fr \
--cc=soc@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).