From: Xianwei Zhao via B4 Relay <devnull+xianwei.zhao.amlogic.com@kernel.org>
To: Neil Armstrong <neil.armstrong@linaro.org>,
Jerome Brunet <jbrunet@baylibre.com>,
Michael Turquette <mturquette@baylibre.com>,
Stephen Boyd <sboyd@kernel.org>, Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
Chuan Liu <chuan.liu@amlogic.com>,
Kevin Hilman <khilman@baylibre.com>,
Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>,
linux-amlogic@lists.infradead.org, linux-clk@vger.kernel.org,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
Xianwei Zhao <xianwei.zhao@amlogic.com>
Subject: [PATCH 3/3] arm64: dts: amlogic: add C3 AW419 board
Date: Tue, 06 Aug 2024 18:27:16 +0800 [thread overview]
Message-ID: <20240806-c3_add_node-v1-3-c0de41341632@amlogic.com> (raw)
In-Reply-To: <20240806-c3_add_node-v1-0-c0de41341632@amlogic.com>
From: Xianwei Zhao <xianwei.zhao@amlogic.com>
Add Amlogic C3 C308L AW419 board.
Signed-off-by: Xianwei Zhao <xianwei.zhao@amlogic.com>
---
arch/arm64/boot/dts/amlogic/Makefile | 1 +
.../boot/dts/amlogic/amlogic-c3-c308l-aw419.dts | 278 +++++++++++++++++++++
2 files changed, 279 insertions(+)
diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index 29417f04f886..2fbda8419c65 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -2,6 +2,7 @@
dtb-$(CONFIG_ARCH_MESON) += amlogic-a4-a113l2-ba400.dtb
dtb-$(CONFIG_ARCH_MESON) += amlogic-a5-a113x2-av400.dtb
dtb-$(CONFIG_ARCH_MESON) += amlogic-c3-c302x-aw409.dtb
+dtb-$(CONFIG_ARCH_MESON) += amlogic-c3-c308l-aw419.dtb
dtb-$(CONFIG_ARCH_MESON) += amlogic-t7-a311d2-an400.dtb
dtb-$(CONFIG_ARCH_MESON) += amlogic-t7-a311d2-khadas-vim4.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-a1-ad401.dtb
diff --git a/arch/arm64/boot/dts/amlogic/amlogic-c3-c308l-aw419.dts b/arch/arm64/boot/dts/amlogic/amlogic-c3-c308l-aw419.dts
new file mode 100644
index 000000000000..d28fd2a1acf0
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/amlogic-c3-c308l-aw419.dts
@@ -0,0 +1,278 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2024 Amlogic, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include "amlogic-c3.dtsi"
+
+/ {
+ model = "Amlogic C308l aw419 Development Board";
+ compatible = "amlogic,aw419", "amlogic,c3";
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ aliases {
+ serial0 = &uart_b;
+ spi0 = &spifc;
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>;
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ /* 9 MiB reserved for ARM Trusted Firmware */
+ secmon_reserved: secmon@7f00000 {
+ compatible = "shared-dma-pool";
+ reg = <0x0 0x07f00000 0x0 0x900000>;
+ no-map;
+ };
+ };
+
+ main_12v: regulator-main-12v {
+ compatible = "regulator-fixed";
+ regulator-name = "12V";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vcc_5v: regulator-vcc-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&main_12v>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vddq: regulator-vddq {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDQ";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ vin-supply = <&main_12v>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vddao_3v3: regulator-vddao-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&main_12v>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vddao_1v8: regulator-vddao-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ddr4_2v5: regulator-ddr4-2v5 {
+ compatible = "regulator-fixed";
+ regulator-name = "DDR4_2V5";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vcc_3v3: regulator-vcc-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vcc_1v8: regulator-vcc-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_3v3>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vdd_1v8: regulator-vdd-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDD1V8_BOOT";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_3v3>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vddio_b: regulator-vddio-3v3-b {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_B";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_3v3>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sdcard: regulator-sdcard {
+ compatible = "regulator-fixed";
+ regulator-name = "SDCARD_POWER";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vddao_3v3>;
+ gpio = <&gpio GPIOA_4 GPIO_ACTIVE_LOW>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+};
+
+&uart_b {
+ status = "okay";
+};
+
+&nand {
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+
+ nand@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ nand-on-flash-bbt;
+
+ partition@0 {
+ label = "boot";
+ reg = <0x0 0x00200000>;
+ };
+ partition@200000 {
+ label = "env";
+ reg = <0x00200000 0x00400000>;
+ };
+ partition@600000 {
+ label = "system";
+ reg = <0x00600000 0x00a00000>;
+ };
+ partition@1000000 {
+ label = "rootfs";
+ reg = <0x01000000 0x03000000>;
+ };
+ partition@4000000 {
+ label = "media";
+ reg = <0x04000000 0x8000000>;
+ };
+ };
+};
+
+ðmac {
+ status = "okay";
+ phy-handle = <&internal_ephy>;
+ phy-mode = "rmii";
+};
+
+&spifc {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pinctrl-0 = <&spifc_pins>;
+ pinctrl-names = "default";
+
+ nand@0 {
+ compatible = "spi-nand";
+ reg = <0>;
+ spi-max-frequency = <83000000>;
+ spi-tx-bus-width = <4>;
+ spi-rx-bus-width = <4>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ status = "disabled";
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "boot";
+ reg = <0 0x200000>;
+ };
+
+ partition@200000 {
+ label = "env";
+ reg = <0x200000 0x400000>;
+ };
+
+ partition@600000 {
+ label = "system";
+ reg = <0x600000 0xa00000>;
+ };
+
+ partition@1000000 {
+ label = "rootfs";
+ reg = <0x1000000 0x3000000>;
+ };
+
+ partition@4000000 {
+ label = "data";
+ reg = <0x4000000 0x8000000>;
+ };
+ };
+ };
+};
+
+&sd {
+ status = "okay";
+ pinctrl-0 = <&sdcard_pins>;
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default","clk-gate";
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ max-frequency = <50000000>;
+ disable-wp;
+
+ cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <&sdcard>;
+ vqmmc-supply = <&sdcard>;
+};
+
+&sdio {
+ pinctrl-0 = <&sdio_m_pins>;
+ pinctrl-1 = <&sdio_m_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+ bus-width = <4>;
+ cap-sd-highspeed;
+ non-removable;
+ max-frequency = <200000000>;
+ disable-wp;
+ cap-sdio-irq;
+ keep-power-in-suspend;
+
+ vmmc-supply = <&sdcard>;
+ vqmmc-supply = <&sdcard>;
+};
--
2.37.1
next prev parent reply other threads:[~2024-08-06 10:28 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-08-06 10:27 [PATCH 0/3] add some node for amlogic c3 Xianwei Zhao via B4 Relay
2024-08-06 10:27 ` [PATCH 1/3] dt-bindings: clock: fix C3 PLL input parameter Xianwei Zhao via B4 Relay
2024-08-06 13:10 ` Krzysztof Kozlowski
2024-08-07 1:55 ` Xianwei Zhao
2024-08-07 5:44 ` Krzysztof Kozlowski
2024-08-07 6:40 ` Xianwei Zhao
2024-08-07 7:01 ` Krzysztof Kozlowski
2024-08-07 7:56 ` Jerome Brunet
2024-08-07 8:07 ` Krzysztof Kozlowski
2024-08-07 8:23 ` Xianwei Zhao
2024-08-06 10:27 ` [PATCH 2/3] arm64: dts: amlogic: add some device nodes for C3 Xianwei Zhao via B4 Relay
2024-08-06 13:13 ` Krzysztof Kozlowski
2024-08-07 5:54 ` Xianwei Zhao
2024-08-07 6:38 ` Krzysztof Kozlowski
2024-08-06 10:27 ` Xianwei Zhao via B4 Relay [this message]
2024-08-06 13:14 ` [PATCH 3/3] arm64: dts: amlogic: add C3 AW419 board Krzysztof Kozlowski
2024-08-07 2:37 ` Xianwei Zhao
2024-08-07 5:44 ` Krzysztof Kozlowski
2024-08-07 7:25 ` Xianwei Zhao
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20240806-c3_add_node-v1-3-c0de41341632@amlogic.com \
--to=devnull+xianwei.zhao.amlogic.com@kernel.org \
--cc=chuan.liu@amlogic.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=jbrunet@baylibre.com \
--cc=khilman@baylibre.com \
--cc=krzk+dt@kernel.org \
--cc=krzysztof.kozlowski@linaro.org \
--cc=linux-amlogic@lists.infradead.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=martin.blumenstingl@googlemail.com \
--cc=mturquette@baylibre.com \
--cc=neil.armstrong@linaro.org \
--cc=robh@kernel.org \
--cc=sboyd@kernel.org \
--cc=xianwei.zhao@amlogic.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).