[PATCH v4 1/2] dt-bindings: arm: ti: Add BeagleY-AI

[PATCH v4 1/2] dt-bindings: arm: ti: Add BeagleY-AI

[Robert Nelson]

This board is based on ti,j722s family using the am67a variation.

https://beagley-ai.org/
https://openbeagle.org/beagley-ai/beagley-ai

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
CC: Nishanth Menon <nm@ti.com>
CC: Vignesh Raghavendra <vigneshr@ti.com>
CC: Tero Kristo <kristo@kernel.org>
CC: Rob Herring <robh@kernel.org>
CC: Conor Dooley <conor+dt@kernel.org>
CC: Andrew Davis <afd@ti.com>
CC: Jared McArthur <j-mcarthur@ti.com>
CC: Andrei Aldea <a-aldea@ti.com>
CC: Jason Kridner <jkridner@beagleboard.org>
CC: Deepak Khatri <lorforlinux@beagleboard.org>
CC: Drew Fustini <drew@beagleboard.org>
---
Changes since v3:
 - Apply acked-bys from Krzysztof Kozlowski
Changes since v2:
 - cc more maintainers and devicetree@vger.kernel.org
Changes since v1:
 - switched to the TI model am67a over the family name j722s
---
 Documentation/devicetree/bindings/arm/ti/k3.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/ti/k3.yaml b/Documentation/devicetree/bindings/arm/ti/k3.yaml
index 4d9c5fbb4c26..5df99e361c21 100644
--- a/Documentation/devicetree/bindings/arm/ti/k3.yaml
+++ b/Documentation/devicetree/bindings/arm/ti/k3.yaml
@@ -140,6 +140,7 @@ properties:
       - description: K3 J722S SoC and Boards
         items:
           - enum:
+              - beagle,am67a-beagley-ai
               - ti,j722s-evm
           - const: ti,j722s
 
-- 
2.39.2

[PATCH v4 2/2] arm64: dts: ti: Add k3-am67a-beagley-ai

[Robert Nelson]

BeagleBoard.org BeagleY-AI is an easy to use, affordable open source
hardware single board computer based on the Texas Instruments AM67A,
which features a quad-core 64-bit Arm CPU subsystem, 2 general-purpose
digital-signal-processors (DSP) and matrix-multiply-accelerators (MMA),
GPU, vision and deep learning accelerators, and multiple Arm Cortex-R5
cores for low-power, low-latency GPIO control.

https://beagley-ai.org/
https://openbeagle.org/beagley-ai/beagley-ai

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Rob Herring <robh@kernel.org>
CC: Krzysztof Kozlowski <krzk+dt@kernel.org>
CC: Conor Dooley <conor+dt@kernel.org>
CC: Vignesh Raghavendra <vigneshr@ti.com>
CC: Nishanth Menon <nm@ti.com>
CC: Andrew Davis <afd@ti.com>
CC: Jai Luthra <j-luthra@ti.com>
CC: Roger Quadros <rogerq@kernel.org>
CC: Siddharth Vadapalli <s-vadapalli@ti.com>
CC: Jared McArthur <j-mcarthur@ti.com>
CC: Andrei Aldea <a-aldea@ti.com>
CC: Jason Kridner <jkridner@beagleboard.org>
CC: Deepak Khatri <lorforlinux@beagleboard.org>
CC: Drew Fustini <drew@beagleboard.org>
---
Changes since v3:
 - removed extra blank lines
 - Krzysztof/Nishanth: switch to consistent regulator-x syntax along with dropping uppercase
 - Roger: removed un-used internal network clock: OBSCLK
 - Nishanth: fixed order of bootph-all before vendor prefixes
 - Nishanth: removed unused default-trigger with led-0 (dtbs_check failure)
Changes since v2:
 - added led indictors
 - sdhci1 use MMC1_SDCD.GPIO1_48 for card detect
 - cleaned up order of status = "okay"
 - wkup_i2c0 moved to 100000
 - eeprom added atmel,24c32
 - rtc added dallas,ds1340
 - sdhci1 use ti,fails-without-test-cd
Changes since v1:
 - fixed incorrect vdd-3v3-sd-pins-default name
 - updated hdmi VDD_1V2 regulator for production pcb
 - switched device tree name from k3-j722s-beagley-ai to k3-am67a-beagley-ai
 - removed cpsw_port2 node
 - enable UHS support for MMCSD
---
 arch/arm64/boot/dts/ti/Makefile               |   1 +
 .../arm64/boot/dts/ti/k3-am67a-beagley-ai.dts | 393 ++++++++++++++++++
 2 files changed, 394 insertions(+)
 create mode 100644 arch/arm64/boot/dts/ti/k3-am67a-beagley-ai.dts

diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index 8dbe7b4979c7..bcd392c3206e 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -116,6 +116,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-j721s2-evm.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-j721s2-evm-pcie1-ep.dtbo
 
 # Boards with J722s SoC
+dtb-$(CONFIG_ARCH_K3) += k3-am67a-beagley-ai.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-j722s-evm.dtb
 
 # Boards with J784s4 SoC
diff --git a/arch/arm64/boot/dts/ti/k3-am67a-beagley-ai.dts b/arch/arm64/boot/dts/ti/k3-am67a-beagley-ai.dts
new file mode 100644
index 000000000000..44dfbdf89277
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am67a-beagley-ai.dts
@@ -0,0 +1,393 @@
+// SPDX-License-Identifier: GPL-2.0-only OR MIT
+/*
+ * https://beagley-ai.org/
+ *
+ * Copyright (C) 2024 Texas Instruments Incorporated - https://www.ti.com/
+ * Copyright (C) 2024 Robert Nelson, BeagleBoard.org Foundation
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/net/ti-dp83867.h>
+#include "k3-j722s.dtsi"
+
+/ {
+	compatible = "beagle,am67a-beagley-ai", "ti,j722s";
+	model = "BeagleBoard.org BeagleY-AI";
+
+	aliases {
+		serial0 = &wkup_uart0;
+		serial2 = &main_uart0;
+		mmc1 = &sdhci1;
+		rtc0 = &rtc;
+	};
+
+	chosen {
+		stdout-path = &main_uart0;
+	};
+
+	memory@80000000 {
+		/* 4G RAM */
+		reg = <0x00000000 0x80000000 0x00000000 0x80000000>,
+		      <0x00000008 0x80000000 0x00000000 0x80000000>;
+		device_type = "memory";
+		bootph-pre-ram;
+	};
+
+	reserved_memory: reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		secure_tfa_ddr: tfa@9e780000 {
+			reg = <0x00 0x9e780000 0x00 0x80000>;
+			no-map;
+		};
+
+		secure_ddr: optee@9e800000 {
+			reg = <0x00 0x9e800000 0x00 0x01800000>;
+			no-map;
+		};
+
+		wkup_r5fss0_core0_memory_region: r5f-memory@a0100000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa0100000 0x00 0xf00000>;
+			no-map;
+		};
+	};
+
+	vsys_5v0: regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "vsys_5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+		bootph-all;
+	};
+
+	vdd_3v3: regulator-2 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vsys_5v0>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vdd_mmc1: regulator-3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_mmc1";
+		pinctrl-names = "default";
+		pinctrl-0 = <&vdd_3v3_sd_pins_default>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&main_gpio1 50 GPIO_ACTIVE_HIGH>;
+		bootph-all;
+	};
+
+	vdd_sd_dv: regulator-4 {
+		compatible = "regulator-gpio";
+		regulator-name = "tlv71033";
+		pinctrl-names = "default";
+		pinctrl-0 = <&vdd_sd_dv_pins_default>;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		vin-supply = <&vsys_5v0>;
+		gpios = <&main_gpio1 49 GPIO_ACTIVE_HIGH>;
+		states = <1800000 0x0>,
+			 <3300000 0x1>;
+		bootph-all;
+	};
+
+	vsys_io_1v8: regulator-5 {
+		compatible = "regulator-fixed";
+		regulator-name = "vsys_io_1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vsys_io_1v2: regulator-6 {
+		compatible = "regulator-fixed";
+		regulator-name = "vsys_io_1v2";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_pins_default>;
+
+		led-0 {
+			gpios = <&main_gpio0 11 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-1 {
+			gpios = <&main_gpio0 12 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			function = LED_FUNCTION_HEARTBEAT;
+			default-state = "on";
+		};
+	};
+};
+
+&main_pmx0 {
+	main_i2c0_pins_default: main-i2c0-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x01e0, PIN_INPUT_PULLUP, 0) /* (D23) I2C0_SCL */
+			J722S_IOPAD(0x01e4, PIN_INPUT_PULLUP, 0) /* (B22) I2C0_SDA */
+		>;
+		bootph-all;
+	};
+
+	main_uart0_pins_default: main-uart0-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x01c8, PIN_INPUT, 0)	/* (A22) UART0_RXD */
+			J722S_IOPAD(0x01cc, PIN_OUTPUT, 0)	/* (B22) UART0_TXD */
+		>;
+		bootph-all;
+	};
+
+	vdd_sd_dv_pins_default: vdd-sd-dv-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x0244, PIN_OUTPUT, 7) /* (A24) MMC1_SDWP.GPIO1_49 */
+		>;
+		bootph-all;
+	};
+
+	main_mmc1_pins_default: main-mmc1-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x023c, PIN_INPUT, 0) /* (H22) MMC1_CMD */
+			J722S_IOPAD(0x0234, PIN_OUTPUT, 0) /* (H24) MMC1_CLK */
+			J722S_IOPAD(0x0230, PIN_INPUT, 0) /* (H23) MMC1_DAT0 */
+			J722S_IOPAD(0x022c, PIN_INPUT_PULLUP, 0) /* (H20) MMC1_DAT1 */
+			J722S_IOPAD(0x0228, PIN_INPUT_PULLUP, 0) /* (J23) MMC1_DAT2 */
+			J722S_IOPAD(0x0224, PIN_INPUT_PULLUP, 0) /* (H25) MMC1_DAT3 */
+			J722S_IOPAD(0x0240, PIN_INPUT, 7) /* (B24) MMC1_SDCD.GPIO1_48 */
+		>;
+		bootph-all;
+	};
+
+	mdio_pins_default: mdio-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x0160, PIN_OUTPUT, 0) /* (AC24) MDIO0_MDC */
+			J722S_IOPAD(0x015c, PIN_INPUT, 0) /* (AD25) MDIO0_MDIO */
+		>;
+	};
+
+	rgmii1_pins_default: rgmii1-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x014c, PIN_INPUT, 0) /* (AC25) RGMII1_RD0 */
+			J722S_IOPAD(0x0150, PIN_INPUT, 0) /* (AD27) RGMII1_RD1 */
+			J722S_IOPAD(0x0154, PIN_INPUT, 0) /* (AE24) RGMII1_RD2 */
+			J722S_IOPAD(0x0158, PIN_INPUT, 0) /* (AE26) RGMII1_RD3 */
+			J722S_IOPAD(0x0148, PIN_INPUT, 0) /* (AE27) RGMII1_RXC */
+			J722S_IOPAD(0x0144, PIN_INPUT, 0) /* (AD23) RGMII1_RX_CTL */
+			J722S_IOPAD(0x0134, PIN_OUTPUT, 0) /* (AF27) RGMII1_TD0 */
+			J722S_IOPAD(0x0138, PIN_OUTPUT, 0) /* (AE23) RGMII1_TD1 */
+			J722S_IOPAD(0x013c, PIN_OUTPUT, 0) /* (AG25) RGMII1_TD2 */
+			J722S_IOPAD(0x0140, PIN_OUTPUT, 0) /* (AF24) RGMII1_TD3 */
+			J722S_IOPAD(0x0130, PIN_OUTPUT, 0) /* (AG26) RGMII1_TXC */
+			J722S_IOPAD(0x012c, PIN_OUTPUT, 0) /* (AF25) RGMII1_TX_CTL */
+		>;
+	};
+
+	led_pins_default: led-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x002c, PIN_OUTPUT, 7) /* (K26) OSPI0_CSn0.GPIO0_11 */
+			J722S_IOPAD(0x0030, PIN_OUTPUT, 7) /* (K23) OSPI0_CSn1.GPIO0_12 */
+		>;
+	};
+
+	pmic_irq_pins_default: pmic-irq-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x01f4, PIN_INPUT_PULLUP, 0) /* (B23) EXTINTn */
+		>;
+	};
+
+	vdd_3v3_sd_pins_default: vdd-3v3-sd-default-pins {
+		pinctrl-single,pins = <
+			J722S_IOPAD(0x0254, PIN_OUTPUT, 7) /* (E25) USB0_DRVVBUS.GPIO1_50 */
+		>;
+	};
+};
+
+&cpsw3g {
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii1_pins_default>;
+	status = "okay";
+};
+
+&cpsw3g_mdio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mdio_pins_default>;
+	status = "okay";
+
+	cpsw3g_phy0: ethernet-phy@0 {
+		reg = <0>;
+		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+		ti,min-output-impedance;
+	};
+};
+
+&cpsw_port1 {
+	phy-mode = "rgmii-rxid";
+	phy-handle = <&cpsw3g_phy0>;
+	status = "okay";
+};
+
+&main_gpio1 {
+	status = "okay";
+};
+
+&main_uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_uart0_pins_default>;
+	bootph-all;
+	status = "okay";
+};
+
+&mcu_pmx0 {
+	wkup_uart0_pins_default: wkup-uart0-default-pins {
+		pinctrl-single,pins = <
+			J722S_MCU_IOPAD(0x02c, PIN_INPUT, 0)	/* (C7) WKUP_UART0_CTSn */
+			J722S_MCU_IOPAD(0x030, PIN_OUTPUT, 0)	/* (C6) WKUP_UART0_RTSn */
+			J722S_MCU_IOPAD(0x024, PIN_INPUT, 0)	/* (D8) WKUP_UART0_RXD */
+			J722S_MCU_IOPAD(0x028, PIN_OUTPUT, 0)	/* (D7) WKUP_UART0_TXD */
+		>;
+		bootph-all;
+	};
+
+	wkup_i2c0_pins_default: wkup-i2c0-default-pins {
+		pinctrl-single,pins = <
+			J722S_MCU_IOPAD(0x04c, PIN_INPUT_PULLUP, 0)	/* (C7) WKUP_I2C0_SCL */
+			J722S_MCU_IOPAD(0x050, PIN_INPUT_PULLUP, 0)	/* (C6) WKUP_I2C1_SDA */
+		>;
+		bootph-all;
+	};
+};
+
+&wkup_uart0 {
+	/* WKUP UART0 is used by Device Manager firmware */
+	pinctrl-names = "default";
+	pinctrl-0 = <&wkup_uart0_pins_default>;
+	bootph-all;
+	status = "reserved";
+};
+
+&wkup_i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&wkup_i2c0_pins_default>;
+	clock-frequency = <100000>;
+	bootph-all;
+	status = "okay";
+
+	tps65219: pmic@30 {
+		compatible = "ti,tps65219";
+		reg = <0x30>;
+		buck1-supply = <&vsys_5v0>;
+		buck2-supply = <&vsys_5v0>;
+		buck3-supply = <&vsys_5v0>;
+		ldo1-supply = <&vdd_3v3>;
+		ldo3-supply = <&vdd_3v3>;
+		ldo4-supply = <&vdd_3v3>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_irq_pins_default>;
+		interrupt-parent = <&gic500>;
+		interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		bootph-all;
+		system-power-controller;
+		ti,power-button;
+
+		regulators {
+			buck1_reg: buck1 {
+				regulator-name = "VDD_3V3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck2_reg: buck2 {
+				regulator-name = "VDD_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo1_reg: ldo1 {
+				regulator-name = "VDDSHV5_SDIO";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-allow-bypass;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo2_reg: ldo2 {
+				regulator-name = "VDD_1V2";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo3_reg: ldo3 {
+				regulator-name = "VDDA_PHY_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo4_reg: ldo4 {
+				regulator-name = "VDDA_PLL_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c32";
+		reg = <0x50>;
+	};
+
+	rtc: rtc@68 {
+		compatible = "dallas,ds1340";
+		reg = <0x68>;
+	};
+};
+
+&sdhci1 {
+	/* SD/MMC */
+	vmmc-supply = <&vdd_mmc1>;
+	vqmmc-supply = <&vdd_sd_dv>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_mmc1_pins_default>;
+	disable-wp;
+	cd-gpios = <&main_gpio1 48 GPIO_ACTIVE_LOW>;
+	cd-debounce-delay-ms = <100>;
+	bootph-all;
+	ti,fails-without-test-cd;
+	status = "okay";
+};
-- 
2.39.2

Re: [PATCH v4 2/2] arm64: dts: ti: Add k3-am67a-beagley-ai

[Roger Quadros]

On 30/08/2024 00:39, Robert Nelson wrote:
> BeagleBoard.org BeagleY-AI is an easy to use, affordable open source
> hardware single board computer based on the Texas Instruments AM67A,
> which features a quad-core 64-bit Arm CPU subsystem, 2 general-purpose
> digital-signal-processors (DSP) and matrix-multiply-accelerators (MMA),
> GPU, vision and deep learning accelerators, and multiple Arm Cortex-R5
> cores for low-power, low-latency GPIO control.
> 
> https://beagley-ai.org/
> https://openbeagle.org/beagley-ai/beagley-ai
> 
> Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
> CC: Rob Herring <robh@kernel.org>
> CC: Krzysztof Kozlowski <krzk+dt@kernel.org>
> CC: Conor Dooley <conor+dt@kernel.org>
> CC: Vignesh Raghavendra <vigneshr@ti.com>
> CC: Nishanth Menon <nm@ti.com>
> CC: Andrew Davis <afd@ti.com>
> CC: Jai Luthra <j-luthra@ti.com>
> CC: Roger Quadros <rogerq@kernel.org>
> CC: Siddharth Vadapalli <s-vadapalli@ti.com>
> CC: Jared McArthur <j-mcarthur@ti.com>
> CC: Andrei Aldea <a-aldea@ti.com>
> CC: Jason Kridner <jkridner@beagleboard.org>
> CC: Deepak Khatri <lorforlinux@beagleboard.org>
> CC: Drew Fustini <drew@beagleboard.org>

Reviewed-by: Roger Quadros <rogerq@kernel.org>

Re: [PATCH v4 2/2] arm64: dts: ti: Add k3-am67a-beagley-ai

[Jared McArthur]

On 8/29/24 16:39, Robert Nelson wrote:
> BeagleBoard.org BeagleY-AI is an easy to use, affordable open source
> hardware single board computer based on the Texas Instruments AM67A,
> which features a quad-core 64-bit Arm CPU subsystem, 2 general-purpose
> digital-signal-processors (DSP) and matrix-multiply-accelerators (MMA),
> GPU, vision and deep learning accelerators, and multiple Arm Cortex-R5
> cores for low-power, low-latency GPIO control.
>
> https://beagley-ai.org/
> https://openbeagle.org/beagley-ai/beagley-ai
>
> Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
> CC: Rob Herring <robh@kernel.org>
> CC: Krzysztof Kozlowski <krzk+dt@kernel.org>
> CC: Conor Dooley <conor+dt@kernel.org>
> CC: Vignesh Raghavendra <vigneshr@ti.com>
> CC: Nishanth Menon <nm@ti.com>
> CC: Andrew Davis <afd@ti.com>
> CC: Jai Luthra <j-luthra@ti.com>
> CC: Roger Quadros <rogerq@kernel.org>
> CC: Siddharth Vadapalli <s-vadapalli@ti.com>
> CC: Jared McArthur <j-mcarthur@ti.com>
> CC: Andrei Aldea <a-aldea@ti.com>
> CC: Jason Kridner <jkridner@beagleboard.org>
> CC: Deepak Khatri <lorforlinux@beagleboard.org>
> CC: Drew Fustini <drew@beagleboard.org>

Reviewed-by: Jared McArthur <j-mcarthur@ti.com>

-- 
Best,
Jared McArthur

Re: [PATCH v4 1/2] dt-bindings: arm: ti: Add BeagleY-AI

[Jared McArthur]

On 8/29/24 16:39, Robert Nelson wrote:
> This board is based on ti,j722s family using the am67a variation.
>
> https://beagley-ai.org/
> https://openbeagle.org/beagley-ai/beagley-ai
>
> Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> CC: Nishanth Menon <nm@ti.com>
> CC: Vignesh Raghavendra <vigneshr@ti.com>
> CC: Tero Kristo <kristo@kernel.org>
> CC: Rob Herring <robh@kernel.org>
> CC: Conor Dooley <conor+dt@kernel.org>
> CC: Andrew Davis <afd@ti.com>
> CC: Jared McArthur <j-mcarthur@ti.com>
> CC: Andrei Aldea <a-aldea@ti.com>
> CC: Jason Kridner <jkridner@beagleboard.org>
> CC: Deepak Khatri <lorforlinux@beagleboard.org>
> CC: Drew Fustini <drew@beagleboard.org>

Reviewed-by: Jared McArthur <j-mcarthur@ti.com>
-- 
Best,
Jared McArthur

Re: [PATCH v4 1/2] dt-bindings: arm: ti: Add BeagleY-AI

[Nishanth Menon]

Hi Robert Nelson,

On Thu, 29 Aug 2024 16:39:28 -0500, Robert Nelson wrote:
> This board is based on ti,j722s family using the am67a variation.
> 
> https://beagley-ai.org/
> https://openbeagle.org/beagley-ai/beagley-ai
> 
> 

I have applied the following to branch ti-k3-dts-next on [1].
Thank you!

[1/2] dt-bindings: arm: ti: Add BeagleY-AI
      commit: b8c773f556936577f8fd7be29c5e579422436784
[2/2] arm64: dts: ti: Add k3-am67a-beagley-ai
      commit: c5e615963bbeda0bdb0a97a33bcba46d6eea8a96

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent up the chain during
the next merge window (or sooner if it is a relevant bug fix), however if
problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux.git
-- 
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3  1A34 DDB5 849D 1736 249D