[PATCH v8 0/9] Add support for sam9x7 SoC family

[PATCH v8 0/9] Add support for sam9x7 SoC family

[Varshini Rajendran]

This patch series adds support for the new SoC family - sam9x7.
 - The device tree, configs and drivers are added
 - Clock driver for sam9x7 is added
 - Support for basic peripherals is added
 - Target board SAM9X75 Curiosity is added

 Changes in v8:
 --------------

 - Dropped patches that are applied from the series
 - Picked up Reviewed-by tags
 - Changed the node name from leds to led-controller in the board dts
   file.

 Changes in v7:
 --------------

 - Addressed all the review comments in the patches
 - Dropped patches that are applied from the series
 - Removed sfr node from the DT to add it later after creating the right
   DT documentation for microchip sfr IPs.
 - All the specific changes are captured in the corresponding patches

 Changes in v6:
 --------------

 - Addressed all the review comments in the patches
 - Picked up all Acked-by and Reviewed-by tags
 - Reverted the IRQ patch to that of version 3 of the same series
 - All the specific changes are captured in the corresponding patches

 Changes in v5:
 --------------

 - Addressed all the review comments in the patches
 - Picked up all Acked-by and Reviewed-by tags
 - Dropped applied patches from the series
 - Addressed the ABI breakage reported in the IRQ patch
 - All the specific changes are captured in the corresponding patches

 Changes in v4:
 --------------

 - Addressed all the review comments in the patches
 - Picked up all Acked-by and Reviewed-by tags
 - Dropped applied patches from the series
 - Added pwm node and related dt binding documentation
 - Added support for exporting some clocks to DT
 - Dropped USB related patches and changes. See NOTE.
 - All the specific changes are captured in the corresponding patches

 NOTE: Owing to the discussion here
 https://lore.kernel.org/linux-devicetree/CAL_JsqJ9PrX6fj-EbffeJce09MXs=B7t+KS_kOinxaRx38=WxA@mail.gmail.com/
 the USB related changes are dropped from this series in order to enable
 us to work on the mentioned issues before adding new compatibles as
 said. The issues/warnings will be addressed in subsequent patches.
 After which the USB related support for sam9x7 SoCs will be added. Hope
 this works out fine.

 Changes in v3:
 --------------

 - Fixed the DT documentation errors pointed out in v2.
 - Dropped Acked-by tag in tcb DT doc patch as it had to be adapted
   according to sam9x7 correctly.
 - Picked by the previously missed tags.
 - Dropped this patch "dt-bindings: usb: generic-ehci: Document clock-names
   property" as the warning was not found while validating DT-schema for
   at91-sam9x75_curiosity.dtb.
 - Dropped redundant words in the commit message.
 - Fixed the CHECK_DTBS warnings validated against
   at91-sam9x75_curiosity.dtb.
 - Renamed dt nodes according to naming convention.
 - Dropped unwanted status property in dts.
 - Removed nodes that are not in use from the board dts.
 - Removed spi DT doc patch from the series as it was already applied
   and a fix patch was applied subsequently. Added a patch to remove the
   compatible to adapt sam9x7.
 - Added sam9x7 compatibles in usb dt documentation.


 Changes in v2:
 --------------

 - Added sam9x7 specific compatibles in DT with fallbacks
 - Documented all the newly added DT compatible strings
 - Added device tree for the target board sam9x75 curiosity and
   documented the same in the DT bindings documentation
 - Removed the dt nodes that are not supported at the moment
 - Removed the configs added by previous version that are not supported
   at the moment
 - Fixed all the corrections in the commit message
 - Changed all the instances of copyright year to 2023
 - Added sam9x7 flag in PIT64B configuration
 - Moved macro definitions to header file
 - Added another divider in mck characteristics in the pmc driver
 - Fixed the memory leak in the pmc driver
 - Dropped patches that are no longer needed
 - Picked up Acked-by and Reviewed-by tags

Varshini Rajendran (9):
  dt-bindings: atmel-ssc: add microchip,sam9x7-ssc
  power: reset: at91-poweroff: lookup for proper pmc dt node for sam9x7
  power: reset: at91-reset: add reset support for sam9x7 SoC
  power: reset: at91-reset: add sdhwc support for sam9x7 SoC
  dt-bindings: reset: atmel,at91sam9260-reset: add sam9x7
  dt-bindings: power: reset: atmel,sama5d2-shdwc: add sam9x7
  ARM: dts: at91: sam9x7: add device tree for SoC
  dt-bindings: arm: add sam9x75 curiosity board
  ARM: dts: microchip: sam9x75_curiosity: add sam9x75 curiosity board

 .../devicetree/bindings/arm/atmel-at91.yaml   |    6 +
 .../devicetree/bindings/misc/atmel-ssc.txt    |    1 +
 .../power/reset/atmel,sama5d2-shdwc.yaml      |    3 +
 .../reset/atmel,at91sam9260-reset.yaml        |    4 +
 arch/arm/boot/dts/microchip/Makefile          |    3 +
 .../dts/microchip/at91-sam9x75_curiosity.dts  |  324 +++++
 arch/arm/boot/dts/microchip/sam9x7.dtsi       | 1220 +++++++++++++++++
 drivers/power/reset/Kconfig                   |    4 +-
 drivers/power/reset/at91-sama5d2_shdwc.c      |    1 +
 9 files changed, 1564 insertions(+), 2 deletions(-)
 create mode 100644 arch/arm/boot/dts/microchip/at91-sam9x75_curiosity.dts
 create mode 100644 arch/arm/boot/dts/microchip/sam9x7.dtsi

-- 
2.25.1

[PATCH v8 1/9] dt-bindings: atmel-ssc: add microchip,sam9x7-ssc

[Varshini Rajendran]

Add microchip,sam9x7-ssc to DT bindings documentation.

Signed-off-by: Varshini Rajendran <varshini.rajendran@microchip.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 Documentation/devicetree/bindings/misc/atmel-ssc.txt | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/misc/atmel-ssc.txt b/Documentation/devicetree/bindings/misc/atmel-ssc.txt
index f9fb412642fe..894875826de9 100644
--- a/Documentation/devicetree/bindings/misc/atmel-ssc.txt
+++ b/Documentation/devicetree/bindings/misc/atmel-ssc.txt
@@ -2,6 +2,7 @@
 
 Required properties:
 - compatible: "atmel,at91rm9200-ssc" or "atmel,at91sam9g45-ssc"
+	       or "microchip,sam9x7-ssc", "atmel,at91sam9g45-ssc"
 	- atmel,at91rm9200-ssc: support pdc transfer
 	- atmel,at91sam9g45-ssc: support dma transfer
 - reg: Should contain SSC registers location and length
-- 
2.25.1

[PATCH v8 2/9] power: reset: at91-poweroff: lookup for proper pmc dt node for sam9x7

[Varshini Rajendran]

Use sam9x7 pmc's compatible to lookup for in the SHDWC driver.

Signed-off-by: Varshini Rajendran <varshini.rajendran@microchip.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
---
 drivers/power/reset/at91-sama5d2_shdwc.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/power/reset/at91-sama5d2_shdwc.c b/drivers/power/reset/at91-sama5d2_shdwc.c
index 959ce0dbe91d..2121d7e74e12 100644
--- a/drivers/power/reset/at91-sama5d2_shdwc.c
+++ b/drivers/power/reset/at91-sama5d2_shdwc.c
@@ -326,6 +326,7 @@ static const struct of_device_id at91_pmc_ids[] = {
 	{ .compatible = "atmel,sama5d2-pmc" },
 	{ .compatible = "microchip,sam9x60-pmc" },
 	{ .compatible = "microchip,sama7g5-pmc" },
+	{ .compatible = "microchip,sam9x7-pmc" },
 	{ /* Sentinel. */ }
 };
 
-- 
2.25.1

[PATCH v8 5/9] dt-bindings: reset: atmel,at91sam9260-reset: add sam9x7

[Varshini Rajendran]

Add documentation for SAM9X7 reset controller.

Signed-off-by: Varshini Rajendran <varshini.rajendran@microchip.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
---
 .../devicetree/bindings/reset/atmel,at91sam9260-reset.yaml    | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/Documentation/devicetree/bindings/reset/atmel,at91sam9260-reset.yaml b/Documentation/devicetree/bindings/reset/atmel,at91sam9260-reset.yaml
index 98465d26949e..c3b33bbc7319 100644
--- a/Documentation/devicetree/bindings/reset/atmel,at91sam9260-reset.yaml
+++ b/Documentation/devicetree/bindings/reset/atmel,at91sam9260-reset.yaml
@@ -26,6 +26,10 @@ properties:
       - items:
           - const: atmel,sama5d3-rstc
           - const: atmel,at91sam9g45-rstc
+      - items:
+          - enum:
+              - microchip,sam9x7-rstc
+          - const: microchip,sam9x60-rstc
 
   reg:
     minItems: 1
-- 
2.25.1

Re: [PATCH v8 5/9] dt-bindings: reset: atmel,at91sam9260-reset: add sam9x7

[Philipp Zabel]

On Di, 2025-01-21 at 10:41 +0000, Varshini.Rajendran@microchip.com
wrote:
> Hi,
> 
> A gentle reminder to merge this patch. It has been left out while the 
> other patches in the series have been merged. Please do the needful.

Applied to reset/next, thanks!

[5/9] dt-bindings: reset: atmel,at91sam9260-reset: add sam9x7
      https://git.pengutronix.de/cgit/pza/linux/commit/?id=d41f0d0bbd79

regards
Philipp

[PATCH v8 6/9] dt-bindings: power: reset: atmel,sama5d2-shdwc: add sam9x7

[Varshini Rajendran]

Add shutdown controller DT bindings.

Signed-off-by: Varshini Rajendran <varshini.rajendran@microchip.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
 .../devicetree/bindings/power/reset/atmel,sama5d2-shdwc.yaml   | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/Documentation/devicetree/bindings/power/reset/atmel,sama5d2-shdwc.yaml b/Documentation/devicetree/bindings/power/reset/atmel,sama5d2-shdwc.yaml
index 8c58e12cdb60..0735ceb7c103 100644
--- a/Documentation/devicetree/bindings/power/reset/atmel,sama5d2-shdwc.yaml
+++ b/Documentation/devicetree/bindings/power/reset/atmel,sama5d2-shdwc.yaml
@@ -22,6 +22,9 @@ properties:
       - enum:
           - atmel,sama5d2-shdwc
           - microchip,sam9x60-shdwc
+      - items:
+          - const: microchip,sam9x7-shdwc
+          - const: microchip,sam9x60-shdwc
 
   reg:
     maxItems: 1
-- 
2.25.1

[PATCH v8 7/9] ARM: dts: at91: sam9x7: add device tree for SoC

[Varshini Rajendran]

Add device tree file for SAM9X7 SoC family.

Co-developed-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Varshini Rajendran <varshini.rajendran@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
---
 arch/arm/boot/dts/microchip/sam9x7.dtsi | 1220 +++++++++++++++++++++++
 1 file changed, 1220 insertions(+)
 create mode 100644 arch/arm/boot/dts/microchip/sam9x7.dtsi

diff --git a/arch/arm/boot/dts/microchip/sam9x7.dtsi b/arch/arm/boot/dts/microchip/sam9x7.dtsi
new file mode 100644
index 000000000000..beb1f34b38d3
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/sam9x7.dtsi
@@ -0,0 +1,1220 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * sam9x7.dtsi - Device Tree Include file for Microchip SAM9X7 SoC family
+ *
+ * Copyright (C) 2023 Microchip Technology Inc. and its subsidiaries
+ *
+ * Author: Varshini Rajendran <varshini.rajendran@microchip.com>
+ */
+
+#include <dt-bindings/clock/at91.h>
+#include <dt-bindings/dma/at91.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/mfd/at91-usart.h>
+#include <dt-bindings/mfd/atmel-flexcom.h>
+#include <dt-bindings/pinctrl/at91.h>
+
+/ {
+	model = "Microchip SAM9X7 SoC";
+	compatible = "microchip,sam9x7";
+	#address-cells = <1>;
+	#size-cells = <1>;
+	interrupt-parent = <&aic>;
+
+	aliases {
+		serial0 = &dbgu;
+		gpio0 = &pioA;
+		gpio1 = &pioB;
+		gpio2 = &pioC;
+		gpio3 = &pioD;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			compatible = "arm,arm926ej-s";
+			reg = <0>;
+			device_type = "cpu";
+		};
+	};
+
+	clocks {
+		slow_xtal: clock-slowxtal {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+		};
+
+		main_xtal: clock-mainxtal {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+		};
+	};
+
+	sram: sram@300000 {
+		compatible = "mmio-sram";
+		reg = <0x300000 0x10000>;
+		ranges = <0 0x300000 0x10000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+
+	ahb {
+		compatible = "simple-bus";
+		ranges;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		sdmmc0: mmc@80000000 {
+			compatible = "microchip,sam9x7-sdhci", "microchip,sam9x60-sdhci";
+			reg = <0x80000000 0x300>;
+			interrupts = <12 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 12>, <&pmc PMC_TYPE_GCK 12>;
+			clock-names = "hclock", "multclk";
+			assigned-clocks = <&pmc PMC_TYPE_GCK 12>;
+			assigned-clock-rates = <100000000>;
+			status = "disabled";
+		};
+
+		sdmmc1: mmc@90000000 {
+			compatible = "microchip,sam9x7-sdhci", "microchip,sam9x60-sdhci";
+			reg = <0x90000000 0x300>;
+			interrupts = <26 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 26>, <&pmc PMC_TYPE_GCK 26>;
+			clock-names = "hclock", "multclk";
+			assigned-clocks = <&pmc PMC_TYPE_GCK 26>;
+			assigned-clock-rates = <100000000>;
+			status = "disabled";
+		};
+	};
+
+	apb {
+		compatible = "simple-bus";
+		ranges;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		flx4: flexcom@f0000000 {
+			compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xf0000000 0x200>;
+			ranges = <0x0 0xf0000000 0x800>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
+			status = "disabled";
+
+			uart4: serial@200 {
+				compatible = "microchip,sam9x7-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
+				clock-names = "usart";
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(8))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(9))>;
+				dma-names = "tx", "rx";
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				atmel,fifo-size = <16>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+
+			spi4: spi@400 {
+				compatible = "microchip,sam9x7-spi", "atmel,at91rm9200-spi";
+				reg = <0x400 0x200>;
+				interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
+				clock-names = "spi_clk";
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(8))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(9))>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <16>;
+				status = "disabled";
+			};
+
+			i2c4: i2c@600 {
+				compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(8))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(9))>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <16>;
+				status = "disabled";
+			};
+		};
+
+		flx5: flexcom@f0004000 {
+			compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xf0004000 0x200>;
+			ranges = <0x0 0xf0004000 0x800>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
+			status = "disabled";
+
+			uart5: serial@200 {
+				compatible = "microchip,sam9x7-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
+				clock-names = "usart";
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(10))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(11))>;
+				dma-names = "tx", "rx";
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				atmel,fifo-size = <16>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+
+			spi5: spi@400 {
+				compatible = "microchip,sam9x7-spi", "atmel,at91rm9200-spi";
+				reg = <0x400 0x200>;
+				interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
+				clock-names = "spi_clk";
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(10))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(11))>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <16>;
+				status = "disabled";
+			};
+
+			i2c5: i2c@600 {
+				compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(10))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(11))>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <16>;
+				status = "disabled";
+			};
+		};
+
+		dma0: dma-controller@f0008000 {
+			compatible = "microchip,sam9x7-dma", "atmel,sama5d4-dma";
+			reg = <0xf0008000 0x1000>;
+			interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>;
+			#dma-cells = <1>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 20>;
+			clock-names = "dma_clk";
+			status = "disabled";
+		};
+
+		ssc: ssc@f0010000 {
+			compatible = "microchip,sam9x7-ssc", "atmel,at91sam9g45-ssc";
+			reg = <0xf0010000 0x4000>;
+			interrupts = <28 IRQ_TYPE_LEVEL_HIGH 5>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 28>;
+			clock-names = "pclk";
+			dmas = <&dma0
+				(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+				 AT91_XDMAC_DT_PERID(38))>,
+			       <&dma0
+				(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+				 AT91_XDMAC_DT_PERID(39))>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		i2s: i2s@f001c000 {
+			compatible = "microchip,sam9x7-i2smcc", "microchip,sam9x60-i2smcc";
+			reg = <0xf001c000 0x100>;
+			interrupts = <34 IRQ_TYPE_LEVEL_HIGH 7>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 34>, <&pmc PMC_TYPE_GCK 34>;
+			clock-names = "pclk", "gclk";
+			dmas = <&dma0
+				(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+				 AT91_XDMAC_DT_PERID(36))>,
+			       <&dma0
+				(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+				 AT91_XDMAC_DT_PERID(37))>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		flx11: flexcom@f0020000 {
+			compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xf0020000 0x200>;
+			ranges = <0x0 0xf0020000 0x800>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 32>;
+			status = "disabled";
+
+			uart11: serial@200 {
+				compatible = "microchip,sam9x7-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <32 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 32>;
+				clock-names = "usart";
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(22))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(23))>;
+				dma-names = "tx", "rx";
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				atmel,fifo-size = <16>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+
+			i2c11: i2c@600 {
+				compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <32 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 32>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(22))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(23))>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <16>;
+				status = "disabled";
+			};
+		};
+
+		flx12: flexcom@f0024000 {
+			compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xf0024000 0x200>;
+			ranges = <0x0 0xf0024000 0x800>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 33>;
+			status = "disabled";
+
+			uart12: serial@200 {
+				compatible = "microchip,sam9x7-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <33 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 33>;
+				clock-names = "usart";
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(24))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(25))>;
+				dma-names = "tx", "rx";
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				atmel,fifo-size = <16>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+
+			i2c12: i2c@600 {
+				compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <33 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 33>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(24))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(25))>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <16>;
+				status = "disabled";
+			};
+		};
+
+		pit64b0: timer@f0028000 {
+			compatible = "microchip,sam9x7-pit64b", "microchip,sam9x60-pit64b";
+			reg = <0xf0028000 0x100>;
+			interrupts = <37 IRQ_TYPE_LEVEL_HIGH 7>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 37>, <&pmc PMC_TYPE_GCK 37>;
+			clock-names = "pclk", "gclk";
+		};
+
+		sha: crypto@f002c000 {
+			compatible = "microchip,sam9x7-sha", "atmel,at91sam9g46-sha";
+			reg = <0xf002c000 0x100>;
+			interrupts = <41 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 41>;
+			clock-names = "sha_clk";
+			dmas = <&dma0
+				(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+				 AT91_XDMAC_DT_PERID(34))>;
+			dma-names = "tx";
+		};
+
+		trng: rng@f0030000 {
+			compatible = "microchip,sam9x7-trng", "microchip,sam9x60-trng";
+			reg = <0xf0030000 0x100>;
+			interrupts = <38 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 38>;
+			status = "disabled";
+		};
+
+		aes: crypto@f0034000 {
+			compatible = "microchip,sam9x7-aes", "atmel,at91sam9g46-aes";
+			reg = <0xf0034000 0x100>;
+			interrupts = <39 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 39>;
+			clock-names = "aes_clk";
+			dmas = <&dma0
+				(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+				 AT91_XDMAC_DT_PERID(32))>,
+			       <&dma0
+				(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+				 AT91_XDMAC_DT_PERID(33))>;
+			dma-names = "tx", "rx";
+		};
+
+		tdes: crypto@f0038000 {
+			compatible = "microchip,sam9x7-tdes", "atmel,at91sam9g46-tdes";
+			reg = <0xf0038000 0x100>;
+			interrupts = <40 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 40>;
+			clock-names = "tdes_clk";
+			dmas = <&dma0
+				(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+				 AT91_XDMAC_DT_PERID(31))>,
+			       <&dma0
+				(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+				 AT91_XDMAC_DT_PERID(30))>;
+			dma-names = "tx", "rx";
+		};
+
+		classd: sound@f003c000 {
+			compatible = "microchip,sam9x7-classd", "atmel,sama5d2-classd";
+			reg = <0xf003c000 0x100>;
+			interrupts = <42 IRQ_TYPE_LEVEL_HIGH 7>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 42>, <&pmc PMC_TYPE_GCK 42>;
+			clock-names = "pclk", "gclk";
+			dmas = <&dma0
+				(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+				 AT91_XDMAC_DT_PERID(35))>;
+			dma-names = "tx";
+			status = "disabled";
+		};
+
+		pit64b1: timer@f0040000 {
+			compatible = "microchip,sam9x7-pit64b", "microchip,sam9x60-pit64b";
+			reg = <0xf0040000 0x100>;
+			interrupts = <58 IRQ_TYPE_LEVEL_HIGH 7>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 58>, <&pmc PMC_TYPE_GCK 58>;
+			clock-names = "pclk", "gclk";
+		};
+
+		can0: can@f8000000 {
+			compatible = "bosch,m_can";
+			reg = <0xf8000000 0x100>, <0x300000 0x7800>;
+			reg-names = "m_can", "message_ram";
+			interrupts = <29 IRQ_TYPE_LEVEL_HIGH 0>,
+				     <68 IRQ_TYPE_LEVEL_HIGH 0>;
+			interrupt-names = "int0", "int1";
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 29>, <&pmc PMC_TYPE_GCK 29>;
+			clock-names = "hclk", "cclk";
+			assigned-clocks = <&pmc PMC_TYPE_CORE PMC_UTMI>, <&pmc PMC_TYPE_GCK 29>;
+			assigned-clock-rates = <480000000>, <40000000>;
+			assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_UTMI>, <&pmc PMC_TYPE_CORE PMC_UTMI>;
+			bosch,mram-cfg = <0x3400 0 0 64 0 0 32 32>;
+			status = "disabled";
+		};
+
+		can1: can@f8004000 {
+			compatible = "bosch,m_can";
+			reg = <0xf8004000 0x100>, <0x300000 0xbc00>;
+			reg-names = "m_can", "message_ram";
+			interrupts = <30 IRQ_TYPE_LEVEL_HIGH 0>,
+				     <69 IRQ_TYPE_LEVEL_HIGH 0>;
+			interrupt-names = "int0", "int1";
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 30>, <&pmc PMC_TYPE_GCK 30>;
+			clock-names = "hclk", "cclk";
+			assigned-clocks = <&pmc PMC_TYPE_CORE PMC_UTMI>, <&pmc PMC_TYPE_GCK 30>;
+			assigned-clock-rates = <480000000>, <40000000>;
+			assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_UTMI>, <&pmc PMC_TYPE_CORE PMC_UTMI>;
+			bosch,mram-cfg = <0x7800 0 0 64 0 0 32 32>;
+			status = "disabled";
+		};
+
+		tcb: timer@f8008000 {
+			compatible = "microchip,sam9x7-tcb","atmel,sama5d2-tcb", "simple-mfd", "syscon";
+			reg = <0xf8008000 0x100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 17>, <&pmc PMC_TYPE_GCK 17>, <&clk32k 0>;
+			clock-names = "t0_clk", "gclk", "slow_clk";
+		};
+
+		flx6: flexcom@f8010000 {
+			compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xf8010000 0x200>;
+			ranges = <0x0 0xf8010000 0x800>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
+			status = "disabled";
+
+			uart6: serial@200 {
+				compatible = "microchip,sam9x7-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
+				clock-names = "usart";
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(12))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(13))>;
+				dma-names = "tx", "rx";
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				atmel,fifo-size = <16>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+
+			i2c6: i2c@600 {
+				compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(12))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(13))>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <16>;
+				status = "disabled";
+			};
+		};
+
+		flx7: flexcom@f8014000 {
+			compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xf8014000 0x200>;
+			ranges = <0x0 0xf8014000 0x800>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 10>;
+			status = "disabled";
+
+			uart7: serial@200 {
+				compatible = "microchip,sam9x7-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <10 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 10>;
+				clock-names = "usart";
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(14))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(15))>;
+				dma-names = "tx", "rx";
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				atmel,fifo-size = <16>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+
+			i2c7: i2c@600 {
+				compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <10 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 10>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(14))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(15))>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <16>;
+				status = "disabled";
+			};
+		};
+
+		flx8: flexcom@f8018000 {
+			compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xf8018000 0x200>;
+			ranges = <0x0 0xf8018000 0x800>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
+			status = "disabled";
+
+			uart8: serial@200 {
+				compatible = "microchip,sam9x7-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <11 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
+				clock-names = "usart";
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(16))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(17))>;
+				dma-names = "tx", "rx";
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				atmel,fifo-size = <16>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+
+			i2c8: i2c@600 {
+				compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <11 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(16))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(17))>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <16>;
+				status = "disabled";
+			};
+		};
+
+		flx0: flexcom@f801c000 {
+			compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xf801c000 0x200>;
+			ranges = <0x0 0xf801c000 0x800>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
+			status = "disabled";
+
+			uart0: serial@200 {
+				compatible = "microchip,sam9x7-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
+				clock-names = "usart";
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(0))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(1))>;
+				dma-names = "tx", "rx";
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				atmel,fifo-size = <16>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+
+			spi0: spi@400 {
+				compatible = "microchip,sam9x7-spi", "atmel,at91rm9200-spi";
+				reg = <0x400 0x200>;
+				interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
+				clock-names = "spi_clk";
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(0))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(1))>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <16>;
+				status = "disabled";
+			};
+
+			i2c0: i2c@600 {
+				compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(0))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(1))>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <16>;
+				status = "disabled";
+			};
+		};
+
+		flx1: flexcom@f8020000 {
+			compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xf8020000 0x200>;
+			ranges = <0x0 0xf8020000 0x800>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
+			status = "disabled";
+
+			uart1: serial@200 {
+				compatible = "microchip,sam9x7-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <6 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
+				clock-names = "usart";
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(2))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(3))>;
+				dma-names = "tx", "rx";
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				atmel,fifo-size = <16>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+
+			spi1: spi@400 {
+				compatible = "microchip,sam9x7-spi", "atmel,at91rm9200-spi";
+				reg = <0x400 0x200>;
+				interrupts = <6 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
+				clock-names = "spi_clk";
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(2))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(3))>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <16>;
+				status = "disabled";
+			};
+
+			i2c1: i2c@600 {
+				compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <6 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(2))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(3))>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <16>;
+				status = "disabled";
+			};
+		};
+
+		flx2: flexcom@f8024000 {
+			compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xf8024000 0x200>;
+			ranges = <0x0 0xf8024000 0x800>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
+			status = "disabled";
+
+			uart2: serial@200 {
+				compatible = "microchip,sam9x7-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <7 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
+				clock-names = "usart";
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(4))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(5))>;
+				dma-names = "tx", "rx";
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				atmel,fifo-size = <16>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+
+			spi2: spi@400 {
+				compatible = "microchip,sam9x7-spi", "atmel,at91rm9200-spi";
+				reg = <0x400 0x200>;
+				interrupts = <7 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
+				clock-names = "spi_clk";
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(4))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(5))>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <16>;
+				status = "disabled";
+			};
+
+			i2c2: i2c@600 {
+				compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <7 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(4))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(5))>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <16>;
+				status = "disabled";
+			};
+		};
+
+		flx3: flexcom@f8028000 {
+			compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xf8028000 0x200>;
+			ranges = <0x0 0xf8028000 0x800>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
+			status = "disabled";
+
+			uart3: serial@200 {
+				compatible = "microchip,sam9x7-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <8 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
+				clock-names = "usart";
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(6))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(7))>;
+				dma-names = "tx", "rx";
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				atmel,fifo-size = <16>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+
+			spi3: spi@400 {
+				compatible = "microchip,sam9x7-spi", "atmel,at91rm9200-spi";
+				reg = <0x400 0x200>;
+				interrupts = <8 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
+				clock-names = "spi_clk";
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(6))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(7))>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <16>;
+				status = "disabled";
+			};
+
+			i2c3: i2c@600 {
+				compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <8 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(6))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(7))>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <16>;
+				status = "disabled";
+			};
+		};
+
+		gmac: ethernet@f802c000 {
+			compatible = "microchip,sam9x7-gem", "microchip,sama7g5-gem";
+			reg = <0xf802c000 0x1000>;
+			interrupts = <24 IRQ_TYPE_LEVEL_HIGH 3>,	/* Queue 0 */
+				     <60 IRQ_TYPE_LEVEL_HIGH 3>,	/* Queue 1 */
+				     <61 IRQ_TYPE_LEVEL_HIGH 3>,	/* Queue 2 */
+				     <62 IRQ_TYPE_LEVEL_HIGH 3>,	/* Queue 3 */
+				     <63 IRQ_TYPE_LEVEL_HIGH 3>,	/* Queue 4 */
+				     <64 IRQ_TYPE_LEVEL_HIGH 3>;	/* Queue 5 */
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 24>, <&pmc PMC_TYPE_PERIPHERAL 24>, <&pmc PMC_TYPE_GCK 24>, <&pmc PMC_TYPE_GCK 67>;
+			clock-names = "hclk", "pclk", "tx_clk", "tsu_clk";
+			assigned-clocks = <&pmc PMC_TYPE_GCK 67>;
+			assigned-clock-rates = <266666666>;
+			status = "disabled";
+		};
+
+		pwm0: pwm@f8034000 {
+			compatible = "microchip,sam9x7-pwm", "microchip,sam9x60-pwm";
+			reg = <0xf8034000 0x300>;
+			interrupts = <18 IRQ_TYPE_LEVEL_HIGH 4>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 18>;
+			#pwm-cells = <3>;
+			status = "disabled";
+		};
+
+		flx9: flexcom@f8040000 {
+			compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xf8040000 0x200>;
+			ranges = <0x0 0xf8040000 0x800>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 15>;
+			status = "disabled";
+
+			uart9: serial@200 {
+				compatible = "microchip,sam9x7-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <15 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 15>;
+				clock-names = "usart";
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(18))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(19))>;
+				dma-names = "tx", "rx";
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				atmel,fifo-size = <16>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+
+			i2c9: i2c@600 {
+				compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <15 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 15>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(18))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(19))>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <16>;
+				status = "disabled";
+			};
+		};
+
+		flx10: flexcom@f8044000 {
+			compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xf8044000 0x200>;
+			ranges = <0x0 0xf8044000 0x800>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 16>;
+			status = "disabled";
+
+			uart10: serial@200 {
+				compatible = "microchip,sam9x7-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <16 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 16>;
+				clock-names = "usart";
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(20))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(21))>;
+				dma-names = "tx", "rx";
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				atmel,fifo-size = <16>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+
+			i2c10: i2c@600 {
+				compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <16 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 16>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(20))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(21))>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <16>;
+				status = "disabled";
+			};
+		};
+
+		matrix: matrix@ffffde00 {
+			compatible = "microchip,sam9x7-matrix", "atmel,at91sam9x5-matrix", "syscon";
+			reg = <0xffffde00 0x200>;
+		};
+
+		pmecc: ecc-engine@ffffe000 {
+			compatible = "microchip,sam9x7-pmecc", "atmel,at91sam9g45-pmecc";
+			reg = <0xffffe000 0x300>, <0xffffe600 0x100>;
+		};
+
+		mpddrc: mpddrc@ffffe800 {
+			compatible = "microchip,sam9x7-ddramc", "atmel,sama5d3-ddramc";
+			reg = <0xffffe800 0x200>;
+			clocks = <&pmc PMC_TYPE_SYSTEM 2>, <&pmc PMC_TYPE_CORE PMC_MCK>;
+			clock-names = "ddrck", "mpddr";
+		};
+
+		smc: smc@ffffea00 {
+			compatible = "microchip,sam9x7-smc", "atmel,at91sam9260-smc", "syscon";
+			reg = <0xffffea00 0x100>;
+		};
+
+		aic: interrupt-controller@fffff100 {
+			compatible = "microchip,sam9x7-aic";
+			reg = <0xfffff100 0x100>;
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			atmel,external-irqs = <31>;
+		};
+
+		dbgu: serial@fffff200 {
+			compatible = "microchip,sam9x7-dbgu", "atmel,at91sam9260-dbgu", "microchip,sam9x7-usart", "atmel,at91sam9260-usart";
+			reg = <0xfffff200 0x200>;
+			interrupts = <47 IRQ_TYPE_LEVEL_HIGH 7>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 47>;
+			clock-names = "usart";
+			dmas = <&dma0
+				(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+				 AT91_XDMAC_DT_PERID(28))>,
+			       <&dma0
+				(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+				 AT91_XDMAC_DT_PERID(29))>;
+			dma-names = "tx", "rx";
+			atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+			status = "disabled";
+		};
+
+		pinctrl: pinctrl@fffff400 {
+			compatible = "microchip,sam9x7-pinctrl", "microchip,sam9x60-pinctrl", "simple-mfd";
+			ranges = <0xfffff400 0xfffff400 0x800>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			/* mux-mask corresponding to sam9x7 SoC in TFBGA228L package */
+			atmel,mux-mask = <
+					 /*  A		B	   C	      D	  */
+					 0xffffffff 0xffffefc0 0xc0ffd000 0x00000000	/* pioA */
+					 0x07ffffff 0x0805fe7f 0x01ff9f81 0x06078000	/* pioB */
+					 0xffffffff 0x07dfffff 0xfa3fffff 0x00000000	/* pioC */
+					 0x00003fff 0x00003fe0 0x0000003f 0x00000000	/* pioD */
+					 >;
+
+			pioA: gpio@fffff400 {
+				compatible = "microchip,sam9x7-gpio", "microchip,sam9x60-gpio", "atmel,at91rm9200-gpio";
+				reg = <0xfffff400 0x200>;
+				interrupts = <2 IRQ_TYPE_LEVEL_HIGH 1>;
+				#interrupt-cells = <2>;
+				interrupt-controller;
+				#gpio-cells = <2>;
+				gpio-controller;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 2>;
+			};
+
+			pioB: gpio@fffff600 {
+				compatible = "microchip,sam9x7-gpio", "microchip,sam9x60-gpio", "atmel,at91rm9200-gpio";
+				reg = <0xfffff600 0x200>;
+				interrupts = <3 IRQ_TYPE_LEVEL_HIGH 1>;
+				#interrupt-cells = <2>;
+				interrupt-controller;
+				#gpio-cells = <2>;
+				gpio-controller;
+				#gpio-lines = <26>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 3>;
+			};
+
+			pioC: gpio@fffff800 {
+				compatible = "microchip,sam9x7-gpio", "microchip,sam9x60-gpio", "atmel,at91rm9200-gpio";
+				reg = <0xfffff800 0x200>;
+				interrupts = <4 IRQ_TYPE_LEVEL_HIGH 1>;
+				#interrupt-cells = <2>;
+				interrupt-controller;
+				#gpio-cells = <2>;
+				gpio-controller;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 4>;
+			};
+
+			pioD: gpio@fffffa00 {
+				compatible = "microchip,sam9x7-gpio", "microchip,sam9x60-gpio", "atmel,at91rm9200-gpio";
+				reg = <0xfffffa00 0x200>;
+				interrupts = <44 IRQ_TYPE_LEVEL_HIGH 1>;
+				#interrupt-cells = <2>;
+				interrupt-controller;
+				#gpio-cells = <2>;
+				gpio-controller;
+				#gpio-lines = <22>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 44>;
+			};
+		};
+
+		pmc: clock-controller@fffffc00 {
+			compatible = "microchip,sam9x7-pmc", "syscon";
+			reg = <0xfffffc00 0x200>;
+			interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+			#clock-cells = <2>;
+			clocks = <&clk32k 1>, <&clk32k 0>, <&main_xtal>;
+			clock-names = "td_slck", "md_slck", "main_xtal";
+		};
+
+		reset_controller: reset-controller@fffffe00 {
+			compatible = "microchip,sam9x7-rstc", "microchip,sam9x60-rstc";
+			reg = <0xfffffe00 0x10>;
+			clocks = <&clk32k 0>;
+		};
+
+		poweroff: poweroff@fffffe10 {
+			compatible = "microchip,sam9x7-shdwc", "microchip,sam9x60-shdwc";
+			reg = <0xfffffe10 0x10>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&clk32k 0>;
+			atmel,wakeup-rtc-timer;
+			atmel,wakeup-rtt-timer;
+			status = "disabled";
+		};
+
+		rtt: rtc@fffffe20 {
+			compatible = "microchip,sam9x7-rtt", "atmel,at91sam9260-rtt";
+			reg = <0xfffffe20 0x20>;
+			interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+			clocks = <&clk32k 0>;
+		};
+
+		clk32k: clock-controller@fffffe50 {
+			compatible = "microchip,sam9x7-sckc", "microchip,sam9x60-sckc";
+			reg = <0xfffffe50 0x4>;
+			clocks = <&slow_xtal>;
+			#clock-cells = <1>;
+		};
+
+		gpbr: syscon@fffffe60 {
+			compatible = "microchip,sam9x7-gpbr", "atmel,at91sam9260-gpbr", "syscon";
+			reg = <0xfffffe60 0x10>;
+		};
+
+		rtc: rtc@fffffea8 {
+			compatible = "microchip,sam9x7-rtc", "microchip,sam9x60-rtc";
+			reg = <0xfffffea8 0x100>;
+			interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+			clocks = <&clk32k 0>;
+		};
+
+		watchdog: watchdog@ffffff80 {
+			compatible = "microchip,sam9x7-wdt", "microchip,sam9x60-wdt";
+			reg = <0xffffff80 0x24>;
+			interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+			status = "disabled";
+		};
+	};
+};
-- 
2.25.1

[PATCH v8 8/9] dt-bindings: arm: add sam9x75 curiosity board

[Varshini Rajendran]

Add documentation for SAM9X75 Curiosity board.

Signed-off-by: Varshini Rajendran <varshini.rajendran@microchip.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
---
 Documentation/devicetree/bindings/arm/atmel-at91.yaml | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.yaml b/Documentation/devicetree/bindings/arm/atmel-at91.yaml
index 82f37328cc69..7160ec80ac1b 100644
--- a/Documentation/devicetree/bindings/arm/atmel-at91.yaml
+++ b/Documentation/devicetree/bindings/arm/atmel-at91.yaml
@@ -106,6 +106,12 @@ properties:
           - const: microchip,sam9x60
           - const: atmel,at91sam9
 
+      - description: Microchip SAM9X7 Evaluation Boards
+        items:
+          - const: microchip,sam9x75-curiosity
+          - const: microchip,sam9x7
+          - const: atmel,at91sam9
+
       - description: Nattis v2 board with Natte v2 power board
         items:
           - const: axentia,nattis-2
-- 
2.25.1

[PATCH v8 9/9] ARM: dts: microchip: sam9x75_curiosity: add sam9x75 curiosity board

[Varshini Rajendran]

Add device tree file for sam9x75 curiosity board.

Signed-off-by: Varshini Rajendran <varshini.rajendran@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Reviewed-by: Hari Prasath Gujulan Elango <hari.prasathge@microchip.com>
---
 arch/arm/boot/dts/microchip/Makefile          |   3 +
 .../dts/microchip/at91-sam9x75_curiosity.dts  | 324 ++++++++++++++++++
 2 files changed, 327 insertions(+)
 create mode 100644 arch/arm/boot/dts/microchip/at91-sam9x75_curiosity.dts

diff --git a/arch/arm/boot/dts/microchip/Makefile b/arch/arm/boot/dts/microchip/Makefile
index 0c45c8d17468..470fe46433a9 100644
--- a/arch/arm/boot/dts/microchip/Makefile
+++ b/arch/arm/boot/dts/microchip/Makefile
@@ -2,6 +2,7 @@
 # Enables support for device-tree overlays
 DTC_FLAGS_at91-sam9x60_curiosity := -@
 DTC_FLAGS_at91-sam9x60ek := -@
+DTC_FLAGS_at91-sam9x75_curiosity := -@
 DTC_FLAGS_at91-sama5d27_som1_ek := -@
 DTC_FLAGS_at91-sama5d27_wlsom1_ek := -@
 DTC_FLAGS_at91-sama5d29_curiosity := -@
@@ -60,6 +61,8 @@ dtb-$(CONFIG_SOC_AT91SAM9) += \
 dtb-$(CONFIG_SOC_SAM9X60) += \
 	at91-sam9x60_curiosity.dtb \
 	at91-sam9x60ek.dtb
+dtb-$(CONFIG_SOC_SAM9X7) += \
+	at91-sam9x75_curiosity.dtb
 dtb-$(CONFIG_SOC_SAM_V7) += \
 	at91-kizbox2-2.dtb \
 	at91-kizbox3-hs.dtb \
diff --git a/arch/arm/boot/dts/microchip/at91-sam9x75_curiosity.dts b/arch/arm/boot/dts/microchip/at91-sam9x75_curiosity.dts
new file mode 100644
index 000000000000..87b6ea97590b
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/at91-sam9x75_curiosity.dts
@@ -0,0 +1,324 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * at91-sam9x75_curiosity.dts - Device Tree file for Microchip SAM9X75 Curiosity board
+ *
+ * Copyright (C) 2023 Microchip Technology Inc. and its subsidiaries
+ *
+ * Author: Varshini Rajendran <varshini.rajendran@microchip.com>
+ */
+/dts-v1/;
+#include "sam9x7.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Microchip SAM9X75 Curiosity";
+	compatible = "microchip,sam9x75-curiosity", "microchip,sam9x7", "atmel,at91sam9";
+
+	aliases {
+		i2c0 = &i2c6;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_key_gpio_default>;
+
+		button-user {
+			label = "USER";
+			gpios = <&pioC 9 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_0>;
+			wakeup-source;
+		};
+	};
+
+	led-controller {
+		compatible = "gpio-leds";
+
+		led_red: led-red {
+			label = "red";
+			gpios = <&pioC 14 GPIO_ACTIVE_HIGH>;
+			pinctrl-0 = <&pinctrl_red_led_gpio_default>;
+		};
+
+		led_green: led-green {
+			label = "green";
+			gpios = <&pioC 21 GPIO_ACTIVE_HIGH>;
+			pinctrl-0 = <&pinctrl_green_led_gpio_default>;
+		};
+
+		led_blue: led-blue {
+			label = "blue";
+			gpios = <&pioC 20 GPIO_ACTIVE_HIGH>;
+			pinctrl-0 = <&pinctrl_blue_led_gpio_default>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	memory@20000000 {
+		reg = <0x20000000 0x10000000>;
+		device_type = "memory";
+	};
+};
+
+&classd {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_classd_default>;
+	atmel,pwm-type = "diff";
+	atmel,non-overlap-time = <10>;
+	status = "okay";
+};
+
+&dbgu {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_dbgu_default>;
+	status = "okay";
+};
+
+&dma0 {
+	status = "okay";
+};
+
+&flx6 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+	status = "okay";
+};
+
+&i2c6 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flx6_default>;
+	i2c-analog-filter;
+	i2c-digital-filter;
+	i2c-digital-filter-width-ns = <35>;
+	status = "okay";
+
+	pmic@5b {
+		compatible = "microchip,mcp16502";
+		reg = <0x5b>;
+
+		regulators {
+			vdd_3v3: VDD_IO {
+				regulator-name = "VDD_IO";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-initial-mode = <2>;
+				regulator-allowed-modes = <2>, <4>;
+				regulator-always-on;
+
+				regulator-state-standby {
+					regulator-on-in-suspend;
+					regulator-mode = <4>;
+				};
+
+				regulator-state-mem {
+					regulator-mode = <4>;
+				};
+			};
+
+			vddioddr: VDD_DDR {
+				regulator-name = "VDD_DDR";
+				regulator-min-microvolt = <1350000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-initial-mode = <2>;
+				regulator-allowed-modes = <2>, <4>;
+				regulator-always-on;
+
+				regulator-state-standby {
+					regulator-on-in-suspend;
+					regulator-mode = <4>;
+				};
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-mode = <4>;
+				};
+			};
+
+			vddcore: VDD_CORE {
+				regulator-name = "VDD_CORE";
+				regulator-min-microvolt = <1150000>;
+				regulator-max-microvolt = <1150000>;
+				regulator-initial-mode = <2>;
+				regulator-allowed-modes = <2>, <4>;
+				regulator-always-on;
+
+				regulator-state-standby {
+					regulator-on-in-suspend;
+					regulator-mode = <4>;
+				};
+
+				regulator-state-mem {
+					regulator-mode = <4>;
+				};
+			};
+
+			dcdc4: VDD_OTHER {
+				regulator-name = "VDD_OTHER";
+				regulator-min-microvolt = <1150000>;
+				regulator-max-microvolt = <1150000>;
+				regulator-initial-mode = <2>;
+				regulator-allowed-modes = <2>, <4>;
+				regulator-ramp-delay = <3125>;
+				regulator-always-on;
+
+				regulator-state-standby {
+					regulator-on-in-suspend;
+					regulator-mode = <4>;
+				};
+
+				regulator-state-mem {
+					regulator-mode = <4>;
+				};
+			};
+
+			vldo1: LDO1 {
+				regulator-name = "LDO1";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+
+				regulator-state-standby {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vldo2: LDO2 {
+				regulator-name = "LDO2";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-standby {
+					regulator-on-in-suspend;
+				};
+			};
+		};
+	};
+};
+
+&i2s {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2s_default>;
+	#sound-dai-cells = <0>;
+	status = "okay";
+};
+
+&main_xtal {
+	clock-frequency = <24000000>;
+};
+
+&pinctrl {
+	classd {
+		pinctrl_classd_default: classd-default {
+			atmel,pins =
+				<AT91_PIOA 18 AT91_PERIPH_C AT91_PINCTRL_PULL_UP>,
+				<AT91_PIOA 19 AT91_PERIPH_C AT91_PINCTRL_PULL_DOWN>;
+		};
+	};
+
+	dbgu {
+		pinctrl_dbgu_default: dbgu-default {
+			atmel,pins = <AT91_PIOA 26 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
+				     <AT91_PIOA 27 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+		};
+	};
+
+	flexcom {
+		pinctrl_flx6_default: flx6-default {
+			atmel,pins =
+				<AT91_PIOA 24 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
+				<AT91_PIOA 25 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
+		};
+	};
+
+	gpio-keys {
+		pinctrl_key_gpio_default: key-gpio-default {
+			atmel,pins = <AT91_PIOC 9 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+	};
+
+	i2s {
+		pinctrl_i2s_default: i2s-default {
+			atmel,pins =
+				<AT91_PIOB 26 AT91_PERIPH_D AT91_PINCTRL_NONE>,		/* I2SCK */
+				<AT91_PIOB 15 AT91_PERIPH_D AT91_PINCTRL_NONE>,		/* I2SWS */
+				<AT91_PIOB 16 AT91_PERIPH_D AT91_PINCTRL_NONE>,		/* I2SDIN */
+				<AT91_PIOB 17 AT91_PERIPH_D AT91_PINCTRL_NONE>,		/* I2SDOUT */
+				<AT91_PIOB 25 AT91_PERIPH_D AT91_PINCTRL_NONE>;		/* I2SMCK */
+		};
+	};
+
+	led-controller {
+		pinctrl_red_led_gpio_default: red-led-gpio-default {
+			atmel,pins = <AT91_PIOC 14 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+		pinctrl_green_led_gpio_default: green-led-gpio-default {
+			atmel,pins = <AT91_PIOC 21 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+		pinctrl_blue_led_gpio_default: blue-led-gpio-default {
+			atmel,pins = <AT91_PIOC 20 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+	};
+
+	sdmmc0 {
+		pinctrl_sdmmc0_default: sdmmc0-default {
+			atmel,pins =
+				<AT91_PIOA 2 AT91_PERIPH_A (AT91_PINCTRL_DRIVE_STRENGTH_HI | AT91_PINCTRL_SLEWRATE_ENA)>,				/* PA2 CK  periph A with pullup */
+				<AT91_PIOA 1 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI | AT91_PINCTRL_SLEWRATE_ENA)>,	/* PA1 CMD periph A with pullup */
+				<AT91_PIOA 0 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI | AT91_PINCTRL_SLEWRATE_ENA)>,	/* PA0 DAT0 periph A */
+				<AT91_PIOA 3 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI | AT91_PINCTRL_SLEWRATE_ENA)>,	/* PA3 DAT1 periph A with pullup */
+				<AT91_PIOA 4 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI | AT91_PINCTRL_SLEWRATE_ENA)>,	/* PA4 DAT2 periph A with pullup */
+				<AT91_PIOA 5 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI | AT91_PINCTRL_SLEWRATE_ENA)>;	/* PA5 DAT3 periph A with pullup */
+		};
+	};
+}; /* pinctrl */
+
+&poweroff {
+	debounce-delay-us = <976>;
+	status = "okay";
+
+	input@0 {
+		reg = <0>;
+	};
+};
+
+&rtt {
+	atmel,rtt-rtc-time-reg = <&gpbr 0x0>;
+};
+
+&sdmmc0 {
+	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdmmc0_default>;
+	cd-gpios = <&pioA 23 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	status = "okay";
+};
+
+&slow_xtal {
+	clock-frequency = <32768>;
+};
+
+&tcb {
+	timer0: timer@0 {
+		compatible = "atmel,tcb-timer";
+		reg = <0>;
+	};
+
+	timer1: timer@1 {
+		compatible = "atmel,tcb-timer";
+		reg = <1>;
+	};
+};
+
+&trng {
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
-- 
2.25.1

Re: [PATCH v8 0/9] Add support for sam9x7 SoC family

[Rob Herring (Arm)]

On Thu, 10 Oct 2024 17:31:42 +0530, Varshini Rajendran wrote:
> This patch series adds support for the new SoC family - sam9x7.
>  - The device tree, configs and drivers are added
>  - Clock driver for sam9x7 is added
>  - Support for basic peripherals is added
>  - Target board SAM9X75 Curiosity is added
> 
>  Changes in v8:
>  --------------
> 
>  - Dropped patches that are applied from the series
>  - Picked up Reviewed-by tags
>  - Changed the node name from leds to led-controller in the board dts
>    file.
> 
>  Changes in v7:
>  --------------
> 
>  - Addressed all the review comments in the patches
>  - Dropped patches that are applied from the series
>  - Removed sfr node from the DT to add it later after creating the right
>    DT documentation for microchip sfr IPs.
>  - All the specific changes are captured in the corresponding patches
> 
>  Changes in v6:
>  --------------
> 
>  - Addressed all the review comments in the patches
>  - Picked up all Acked-by and Reviewed-by tags
>  - Reverted the IRQ patch to that of version 3 of the same series
>  - All the specific changes are captured in the corresponding patches
> 
>  Changes in v5:
>  --------------
> 
>  - Addressed all the review comments in the patches
>  - Picked up all Acked-by and Reviewed-by tags
>  - Dropped applied patches from the series
>  - Addressed the ABI breakage reported in the IRQ patch
>  - All the specific changes are captured in the corresponding patches
> 
>  Changes in v4:
>  --------------
> 
>  - Addressed all the review comments in the patches
>  - Picked up all Acked-by and Reviewed-by tags
>  - Dropped applied patches from the series
>  - Added pwm node and related dt binding documentation
>  - Added support for exporting some clocks to DT
>  - Dropped USB related patches and changes. See NOTE.
>  - All the specific changes are captured in the corresponding patches
> 
>  NOTE: Owing to the discussion here
>  https://lore.kernel.org/linux-devicetree/CAL_JsqJ9PrX6fj-EbffeJce09MXs=B7t+KS_kOinxaRx38=WxA@mail.gmail.com/
>  the USB related changes are dropped from this series in order to enable
>  us to work on the mentioned issues before adding new compatibles as
>  said. The issues/warnings will be addressed in subsequent patches.
>  After which the USB related support for sam9x7 SoCs will be added. Hope
>  this works out fine.
> 
>  Changes in v3:
>  --------------
> 
>  - Fixed the DT documentation errors pointed out in v2.
>  - Dropped Acked-by tag in tcb DT doc patch as it had to be adapted
>    according to sam9x7 correctly.
>  - Picked by the previously missed tags.
>  - Dropped this patch "dt-bindings: usb: generic-ehci: Document clock-names
>    property" as the warning was not found while validating DT-schema for
>    at91-sam9x75_curiosity.dtb.
>  - Dropped redundant words in the commit message.
>  - Fixed the CHECK_DTBS warnings validated against
>    at91-sam9x75_curiosity.dtb.
>  - Renamed dt nodes according to naming convention.
>  - Dropped unwanted status property in dts.
>  - Removed nodes that are not in use from the board dts.
>  - Removed spi DT doc patch from the series as it was already applied
>    and a fix patch was applied subsequently. Added a patch to remove the
>    compatible to adapt sam9x7.
>  - Added sam9x7 compatibles in usb dt documentation.
> 
> 
>  Changes in v2:
>  --------------
> 
>  - Added sam9x7 specific compatibles in DT with fallbacks
>  - Documented all the newly added DT compatible strings
>  - Added device tree for the target board sam9x75 curiosity and
>    documented the same in the DT bindings documentation
>  - Removed the dt nodes that are not supported at the moment
>  - Removed the configs added by previous version that are not supported
>    at the moment
>  - Fixed all the corrections in the commit message
>  - Changed all the instances of copyright year to 2023
>  - Added sam9x7 flag in PIT64B configuration
>  - Moved macro definitions to header file
>  - Added another divider in mck characteristics in the pmc driver
>  - Fixed the memory leak in the pmc driver
>  - Dropped patches that are no longer needed
>  - Picked up Acked-by and Reviewed-by tags
> 
> Varshini Rajendran (9):
>   dt-bindings: atmel-ssc: add microchip,sam9x7-ssc
>   power: reset: at91-poweroff: lookup for proper pmc dt node for sam9x7
>   power: reset: at91-reset: add reset support for sam9x7 SoC
>   power: reset: at91-reset: add sdhwc support for sam9x7 SoC
>   dt-bindings: reset: atmel,at91sam9260-reset: add sam9x7
>   dt-bindings: power: reset: atmel,sama5d2-shdwc: add sam9x7
>   ARM: dts: at91: sam9x7: add device tree for SoC
>   dt-bindings: arm: add sam9x75 curiosity board
>   ARM: dts: microchip: sam9x75_curiosity: add sam9x75 curiosity board
> 
>  .../devicetree/bindings/arm/atmel-at91.yaml   |    6 +
>  .../devicetree/bindings/misc/atmel-ssc.txt    |    1 +
>  .../power/reset/atmel,sama5d2-shdwc.yaml      |    3 +
>  .../reset/atmel,at91sam9260-reset.yaml        |    4 +
>  arch/arm/boot/dts/microchip/Makefile          |    3 +
>  .../dts/microchip/at91-sam9x75_curiosity.dts  |  324 +++++
>  arch/arm/boot/dts/microchip/sam9x7.dtsi       | 1220 +++++++++++++++++
>  drivers/power/reset/Kconfig                   |    4 +-
>  drivers/power/reset/at91-sama5d2_shdwc.c      |    1 +
>  9 files changed, 1564 insertions(+), 2 deletions(-)
>  create mode 100644 arch/arm/boot/dts/microchip/at91-sam9x75_curiosity.dts
>  create mode 100644 arch/arm/boot/dts/microchip/sam9x7.dtsi
> 
> --
> 2.25.1
> 
> 
> 


My bot found new DTB warnings on the .dts files added or changed in this
series.

Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
are fixed by another series. Ultimately, it is up to the platform
maintainer whether these warnings are acceptable or not. No need to reply
unless the platform maintainer has comments.

If you already ran DT checks and didn't see these error(s), then
make sure dt-schema is up to date:

  pip3 install dtschema --upgrade


New warnings running 'make CHECK_DTBS=y microchip/at91-sam9x75_curiosity.dtb' for 20241010120142.92057-1-varshini.rajendran@microchip.com:

arch/arm/boot/dts/microchip/at91-sam9x75_curiosity.dtb: /apb/dma-controller@f0008000: failed to match any schema with compatible: ['microchip,sam9x7-dma', 'atmel,sama5d4-dma']
arch/arm/boot/dts/microchip/at91-sam9x75_curiosity.dtb: /apb/dma-controller@f0008000: failed to match any schema with compatible: ['microchip,sam9x7-dma', 'atmel,sama5d4-dma']
arch/arm/boot/dts/microchip/at91-sam9x75_curiosity.dtb: /apb/ssc@f0010000: failed to match any schema with compatible: ['microchip,sam9x7-ssc', 'atmel,at91sam9g45-ssc']
arch/arm/boot/dts/microchip/at91-sam9x75_curiosity.dtb: /apb/ssc@f0010000: failed to match any schema with compatible: ['microchip,sam9x7-ssc', 'atmel,at91sam9g45-ssc']
arch/arm/boot/dts/microchip/at91-sam9x75_curiosity.dtb: /apb/timer@f0028000: failed to match any schema with compatible: ['microchip,sam9x7-pit64b', 'microchip,sam9x60-pit64b']
arch/arm/boot/dts/microchip/at91-sam9x75_curiosity.dtb: /apb/timer@f0028000: failed to match any schema with compatible: ['microchip,sam9x7-pit64b', 'microchip,sam9x60-pit64b']
arch/arm/boot/dts/microchip/at91-sam9x75_curiosity.dtb: /apb/timer@f0040000: failed to match any schema with compatible: ['microchip,sam9x7-pit64b', 'microchip,sam9x60-pit64b']
arch/arm/boot/dts/microchip/at91-sam9x75_curiosity.dtb: /apb/timer@f0040000: failed to match any schema with compatible: ['microchip,sam9x7-pit64b', 'microchip,sam9x60-pit64b']
arch/arm/boot/dts/microchip/at91-sam9x75_curiosity.dtb: /apb/matrix@ffffde00: failed to match any schema with compatible: ['microchip,sam9x7-matrix', 'atmel,at91sam9x5-matrix', 'syscon']
arch/arm/boot/dts/microchip/at91-sam9x75_curiosity.dtb: /apb/matrix@ffffde00: failed to match any schema with compatible: ['microchip,sam9x7-matrix', 'atmel,at91sam9x5-matrix', 'syscon']
arch/arm/boot/dts/microchip/at91-sam9x75_curiosity.dtb: /apb/ecc-engine@ffffe000: failed to match any schema with compatible: ['microchip,sam9x7-pmecc', 'atmel,at91sam9g45-pmecc']
arch/arm/boot/dts/microchip/at91-sam9x75_curiosity.dtb: /apb/ecc-engine@ffffe000: failed to match any schema with compatible: ['microchip,sam9x7-pmecc', 'atmel,at91sam9g45-pmecc']
arch/arm/boot/dts/microchip/at91-sam9x75_curiosity.dtb: /apb/mpddrc@ffffe800: failed to match any schema with compatible: ['microchip,sam9x7-ddramc', 'atmel,sama5d3-ddramc']
arch/arm/boot/dts/microchip/at91-sam9x75_curiosity.dtb: /apb/mpddrc@ffffe800: failed to match any schema with compatible: ['microchip,sam9x7-ddramc', 'atmel,sama5d3-ddramc']
arch/arm/boot/dts/microchip/at91-sam9x75_curiosity.dtb: /apb/smc@ffffea00: failed to match any schema with compatible: ['microchip,sam9x7-smc', 'atmel,at91sam9260-smc', 'syscon']
arch/arm/boot/dts/microchip/at91-sam9x75_curiosity.dtb: /apb/smc@ffffea00: failed to match any schema with compatible: ['microchip,sam9x7-smc', 'atmel,at91sam9260-smc', 'syscon']
arch/arm/boot/dts/microchip/at91-sam9x75_curiosity.dtb: /apb/syscon@fffffe60: failed to match any schema with compatible: ['microchip,sam9x7-gpbr', 'atmel,at91sam9260-gpbr', 'syscon']
arch/arm/boot/dts/microchip/at91-sam9x75_curiosity.dtb: /apb/syscon@fffffe60: failed to match any schema with compatible: ['microchip,sam9x7-gpbr', 'atmel,at91sam9260-gpbr', 'syscon']

Re: (subset) [PATCH v8 0/9] Add support for sam9x7 SoC family

[Sebastian Reichel]

On Thu, 10 Oct 2024 17:31:42 +0530, Varshini Rajendran wrote:
> This patch series adds support for the new SoC family - sam9x7.
>  - The device tree, configs and drivers are added
>  - Clock driver for sam9x7 is added
>  - Support for basic peripherals is added
>  - Target board SAM9X75 Curiosity is added
> 
>  Changes in v8:
>  --------------
> 
> [...]

Applied, thanks!

[2/9] power: reset: at91-poweroff: lookup for proper pmc dt node for sam9x7
      commit: 2a16675e254a35f13203c6738a1137093c773056
[3/9] power: reset: at91-reset: add reset support for sam9x7 SoC
      commit: ef4f3ac4be990511a2c958443744d0c0c97deb5b
[4/9] power: reset: at91-reset: add sdhwc support for sam9x7 SoC
      commit: 250bbd612bb1103745ea6c891a2a1d5f5e1576a3
[6/9] dt-bindings: power: reset: atmel,sama5d2-shdwc: add sam9x7
      commit: 2d656827a0fc9ca4982c245f1bec3b606fab30d8

Best regards,
-- 
Sebastian Reichel <sebastian.reichel@collabora.com>