[PATCH v2 13/13] KVM: Documentation: Add KVM_CAP_USERFAULT and KVM_MEM_USERFAULT details

[James Houghton <jthoughton@google.com>]

Include the note about memory ordering when clearing bits in
userfault_bitmap, as it may not be obvious for users.

Signed-off-by: James Houghton <jthoughton@google.com>
Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com>
---
 Documentation/virt/kvm/api.rst | 33 ++++++++++++++++++++++++++++++++-
 1 file changed, 32 insertions(+), 1 deletion(-)

diff --git a/Documentation/virt/kvm/api.rst b/Documentation/virt/kvm/api.rst
index 454c2aaa155e..eec485dcf0bc 100644
--- a/Documentation/virt/kvm/api.rst
+++ b/Documentation/virt/kvm/api.rst
@@ -6281,7 +6281,8 @@ bounds checks apply (use common sense).
 	__u64 guest_memfd_offset;
 	__u32 guest_memfd;
 	__u32 pad1;
-	__u64 pad2[14];
+	__u64 userfault_bitmap;
+	__u64 pad2[13];
   };
 
 A KVM_MEM_GUEST_MEMFD region _must_ have a valid guest_memfd (private memory) and
@@ -6297,6 +6298,25 @@ state.  At VM creation time, all memory is shared, i.e. the PRIVATE attribute
 is '0' for all gfns.  Userspace can control whether memory is shared/private by
 toggling KVM_MEMORY_ATTRIBUTE_PRIVATE via KVM_SET_MEMORY_ATTRIBUTES as needed.
 
+When the KVM_MEM_USERFAULT flag is set, userfault_bitmap points to the starting
+address for the bitmap that controls if vCPU memory faults should immediately
+exit to userspace. If an invalid pointer is provided, at fault time, KVM_RUN
+will return -EFAULT. KVM_MEM_USERFAULT is only supported when
+KVM_CAP_USERFAULT is supported.
+
+userfault_bitmap should point to an array of longs where each bit in the array
+linearly corresponds to a single gfn. Bit 0 in userfault_bitmap corresponds to
+guest_phys_addr, bit 1 corresponds to guest_phys_addr + PAGE_SIZE, etc. If the
+bit for a page is set, any vCPU access to that page will exit to userspace with
+KVM_MEMORY_EXIT_FLAG_USERFAULT.
+
+Setting bits in userfault_bitmap has no effect on pages that have already been
+mapped by KVM until KVM_MEM_USERFAULT is disabled and re-enabled again.
+
+Clearing bits in userfault_bitmap should usually be done with a store-release
+if changes to guest memory are being made available to the guest via
+userfault_bitmap.
+
 S390:
 ^^^^^
 
@@ -8251,6 +8271,17 @@ KVM exits with the register state of either the L1 or L2 guest
 depending on which executed at the time of an exit. Userspace must
 take care to differentiate between these cases.
 
+7.37 KVM_CAP_USERFAULT
+----------------------
+
+:Architectures: x86, arm64
+:Returns: Informational only, -EINVAL on direct KVM_ENABLE_CAP.
+
+The presence of this capability indicates that KVM_SET_USER_MEMORY_REGION2 will
+accept KVM_MEM_USERFAULT as a valid memslot flag.
+
+See KVM_SET_USER_MEMORY_REGION2 for more details.
+
 8. Other capabilities.
 ======================
 
-- 
2.47.1.613.gc27f4b7a9f-goog