Re: [RFC v2 PATCH 03/10] net: ti: prueth: Adds PRUETH HW and SW configuration

[Simon Horman <horms@kernel.org>]

On Fri, Jan 24, 2025 at 05:53:46PM +0530, Basharath Hussain Khaja wrote:
> From: Roger Quadros <rogerq@ti.com>
> 
> Updates for MII_RT hardware peripheral configuration such as RX and TX
> configuration for PRU0 and PRU1, frame sizes, and MUX config.
> 
> Updates for PRU-ICSS firmware register configuration and DRAM, SRAM and
> OCMC memory initialization, which will be used in the runtime for packet
> reception and transmission.
> 
> DUAL-EMAC memory allocation for software queues and its supporting
> components such as the buffer descriptors and queue discriptors. These

nit: descriptors

> software queues are placed in OCMC memory and are shared with CPU by
> PRU-ICSS for packet receive and transmit.
> 
> All declarations and macros are being used from common header file
> for various protocols.
> 
> Signed-off-by: Roger Quadros <rogerq@ti.com>
> Signed-off-by: Andrew F. Davis <afd@ti.com>
> Signed-off-by: Parvathi Pudi <parvathi@couthit.com>
> Signed-off-by: Basharath Hussain Khaja <basharath@couthit.com>

...

> diff --git a/drivers/net/ethernet/ti/icssm/icssm_prueth.c b/drivers/net/ethernet/ti/icssm/icssm_prueth.c

...

> +static void icssm_prueth_mii_init(struct prueth *prueth)
> +{
> +	struct regmap *mii_rt;
> +	u32 rxcfg_reg, rxcfg;
> +	u32 txcfg_reg, txcfg;
> +
> +	mii_rt = prueth->mii_rt;
> +
> +	rxcfg = PRUSS_MII_RT_RXCFG_RX_ENABLE |
> +		PRUSS_MII_RT_RXCFG_RX_DATA_RDY_MODE_DIS |
> +		PRUSS_MII_RT_RXCFG_RX_L2_EN |
> +		PRUSS_MII_RT_RXCFG_RX_CUT_PREAMBLE |
> +		PRUSS_MII_RT_RXCFG_RX_L2_EOF_SCLR_DIS;
> +
> +	/* Configuration of Port 0 Rx */
> +	rxcfg_reg = PRUSS_MII_RT_RXCFG0;
> +
> +	regmap_write(mii_rt, rxcfg_reg, rxcfg);
> +
> +	/* Configuration of Port 1 Rx */
> +	rxcfg_reg = PRUSS_MII_RT_RXCFG1;
> +
> +	rxcfg |= PRUSS_MII_RT_RXCFG_RX_MUX_SEL;
> +
> +	regmap_write(mii_rt, rxcfg_reg, rxcfg);
> +
> +	txcfg = PRUSS_MII_RT_TXCFG_TX_ENABLE |
> +		PRUSS_MII_RT_TXCFG_TX_AUTO_PREAMBLE |
> +		PRUSS_MII_RT_TXCFG_TX_32_MODE_EN |
> +		(TX_START_DELAY << PRUSS_MII_RT_TXCFG_TX_START_DELAY_SHIFT) |
> +		(TX_CLK_DELAY_100M << PRUSS_MII_RT_TXCFG_TX_CLK_DELAY_SHIFT);
> +
> +	/* Configuration of Port 0 Tx */
> +	txcfg_reg = PRUSS_MII_RT_TXCFG0;
> +
> +	regmap_write(mii_rt, txcfg_reg, txcfg);
> +
> +	txcfg	|= PRUSS_MII_RT_TXCFG_TX_MUX_SEL;

nit: a space seems more appropriate than a tab before '|='

> +
> +	/* Configuration of Port 1 Tx */
> +	txcfg_reg = PRUSS_MII_RT_TXCFG1;
> +
> +	regmap_write(mii_rt, txcfg_reg, txcfg);
> +
> +	txcfg_reg = PRUSS_MII_RT_RX_FRMS0;
> +
> +	/* Min frame length should be set to 64 to allow receive of standard
> +	 * Ethernet frames such as PTP, LLDP that will not have the tag/rct.
> +	 * Actual size written to register is size - 1 per TRM. This also
> +	 * includes CRC/FCS.
> +	 */
> +	txcfg = (((PRUSS_MII_RT_RX_FRMS_MIN_FRM - 1) <<
> +			PRUSS_MII_RT_RX_FRMS_MIN_FRM_SHIFT) &
> +			PRUSS_MII_RT_RX_FRMS_MIN_FRM_MASK);
> +
> +	/* For EMAC, set Max frame size to 1528 i.e size with VLAN.
> +	 * Actual size written to register is size - 1 as per TRM.
> +	 * Since driver support run time change of protocol, driver
> +	 * must overwrite the values based on Ethernet type.
> +	 */
> +	txcfg |= (((PRUSS_MII_RT_RX_FRMS_MAX_SUPPORT_EMAC - 1) <<
> +			   PRUSS_MII_RT_RX_FRMS_MAX_FRM_SHIFT)	&
> +			   PRUSS_MII_RT_RX_FRMS_MAX_FRM_MASK);
> +
> +	regmap_write(mii_rt, txcfg_reg, txcfg);
> +
> +	txcfg_reg = PRUSS_MII_RT_RX_FRMS1;
> +
> +	regmap_write(mii_rt, txcfg_reg, txcfg);
> +}

...

> @@ -377,6 +705,70 @@ static int icssm_prueth_probe(struct platform_device *pdev)
>  		}
>  	}
>  
> +	pruss = pruss_get(prueth->pru0 ? prueth->pru0 : prueth->pru1);
> +	if (IS_ERR(pruss)) {
> +		ret = PTR_ERR(pruss);
> +		dev_err(dev, "unable to get pruss handle\n");
> +		goto put_pru;
> +	}
> +	prueth->pruss = pruss;
> +
> +	ret = pruss_cfg_ocp_master_ports(prueth->pruss, 1);
> +	if (ret) {
> +		dev_err(dev, "couldn't enabled ocp master port: %d\n", ret);
> +		goto put_pruss;
> +	}

FTR, I applied this patch set on top of the patch at the link below
so that pruss_cfg_ocp_master_ports() is present.

- [PATCH v2 1/1] soc: ti: PRUSS OCP configuration
  https://lore.kernel.org/all/20250108125937.10604-2-basharath@couthit.com/

  ...

> diff --git a/drivers/net/ethernet/ti/icssm/icssm_prueth.h b/drivers/net/ethernet/ti/icssm/icssm_prueth.h

...

> +/**
> + * struct prueth_queue - Information about a queue in memory

struct prueth_queue_info

> + * @buffer_offset: buffer offset in OCMC RAM
> + * @queue_desc_offset: queue descriptor offset in Shared RAM
> + * @buffer_desc_offset: buffer descriptors offset in Shared RAM
> + * @buffer_desc_end: end address of buffer descriptors in Shared RAM
> + */
> +struct prueth_queue_info {
> +	u16 buffer_offset;
> +	u16 queue_desc_offset;
> +	u16 buffer_desc_offset;
> +	u16 buffer_desc_end;
> +} __packed;

...