public inbox for linux-arm-kernel@lists.infradead.org
 help / color / mirror / Atom feed
From: Siddharth Vadapalli <s-vadapalli@ti.com>
To: <peter.chen@kernel.org>, <pawell@cadence.com>,
	<rogerq@kernel.org>, <gregkh@linuxfoundation.org>,
	<balbi@kernel.org>, <jun.li@nxp.com>
Cc: <linux-usb@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
	<stable@vger.kernel.org>, <linux-arm-kernel@lists.infradead.org>,
	<srk@ti.com>, <s-vadapalli@ti.com>
Subject: [PATCH] usb: cdns3: exit cdns3_gadget_udc_start if FAST_REG_ACCESS cannot be set
Date: Thu, 6 Feb 2025 18:29:36 +0530	[thread overview]
Message-ID: <20250206125943.786949-1-s-vadapalli@ti.com> (raw)

When the device is in a low power state, access to the following
registers takes a long time:
- EP_CFG
- EP_TRADDR
- EP_CMD
- EP_SEL
- EP_STS
- USB_CONF

To address this, the fast register access feature can be enabled by
setting PUSB_PWR_FST_REG_ACCESS bit of the USB_PWR register, which
allows quick access by software. Software is expected to poll on
PUSB_PWR_FST_REG_ACCESS_STAT to ensure that fast register access has
been enabled by the controller. Attempting to access any of the
aforementioned registers after setting PUSB_PWR_FST_REG_ACCESS but
before PUSB_PWR_FST_REG_ACCESS_STAT has been set will result in
undefined behavior and potentially result in system hang.

Hence, poll on PUSB_PWR_FST_REG_ACCESS_STAT before proceeding with
gadget configuration, and exit if it cannot be enabled.

Fixes: b5148d946f45 ("usb: cdns3: gadget: set fast access bit")
Cc: <stable@vger.kernel.org>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
---

Hello,

This patch is based on commit
92514ef226f5 Merge tag 'for-6.14-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
of Mainline Linux.

Regards,
Siddharth.

 drivers/usb/cdns3/cdns3-gadget.c | 18 ++++++++++++++++--
 1 file changed, 16 insertions(+), 2 deletions(-)

diff --git a/drivers/usb/cdns3/cdns3-gadget.c b/drivers/usb/cdns3/cdns3-gadget.c
index fd1beb10bba7..b62691944272 100644
--- a/drivers/usb/cdns3/cdns3-gadget.c
+++ b/drivers/usb/cdns3/cdns3-gadget.c
@@ -2971,8 +2971,6 @@ static void cdns3_gadget_config(struct cdns3_device *priv_dev)
 	/* enable generic interrupt*/
 	writel(USB_IEN_INIT, &regs->usb_ien);
 	writel(USB_CONF_CLK2OFFDS | USB_CONF_L1DS, &regs->usb_conf);
-	/*  keep Fast Access bit */
-	writel(PUSB_PWR_FST_REG_ACCESS, &priv_dev->regs->usb_pwr);
 
 	cdns3_configure_dmult(priv_dev, NULL);
 }
@@ -2990,6 +2988,8 @@ static int cdns3_gadget_udc_start(struct usb_gadget *gadget,
 	struct cdns3_device *priv_dev = gadget_to_cdns3_device(gadget);
 	unsigned long flags;
 	enum usb_device_speed max_speed = driver->max_speed;
+	int ret;
+	u32 reg;
 
 	spin_lock_irqsave(&priv_dev->lock, flags);
 	priv_dev->gadget_driver = driver;
@@ -2997,6 +2997,20 @@ static int cdns3_gadget_udc_start(struct usb_gadget *gadget,
 	/* limit speed if necessary */
 	max_speed = min(driver->max_speed, gadget->max_speed);
 
+	/*  keep Fast Access bit */
+	writel(PUSB_PWR_FST_REG_ACCESS, &priv_dev->regs->usb_pwr);
+	reg = readl(&priv_dev->regs->usb_pwr);
+	if (!(reg & PUSB_PWR_FST_REG_ACCESS_STAT)) {
+		ret = readl_poll_timeout_atomic(&priv_dev->regs->usb_pwr, reg,
+						(reg & PUSB_PWR_FST_REG_ACCESS_STAT),
+						10, 1000);
+		if (ret) {
+			dev_err(priv_dev->dev, "Failed to enable fast access\n");
+			spin_unlock_irqrestore(&priv_dev->lock, flags);
+			return ret;
+		}
+	}
+
 	switch (max_speed) {
 	case USB_SPEED_FULL:
 		writel(USB_CONF_SFORCE_FS, &priv_dev->regs->usb_conf);
-- 
2.43.0



             reply	other threads:[~2025-02-06 13:01 UTC|newest]

Thread overview: 5+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2025-02-06 12:59 Siddharth Vadapalli [this message]
2025-02-07  2:25 ` [PATCH] usb: cdns3: exit cdns3_gadget_udc_start if FAST_REG_ACCESS cannot be set Peter Chen
2025-02-07  5:42   ` Siddharth Vadapalli
2025-02-08  5:39     ` Peter Chen
2025-02-08  7:12       ` Siddharth Vadapalli

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20250206125943.786949-1-s-vadapalli@ti.com \
    --to=s-vadapalli@ti.com \
    --cc=balbi@kernel.org \
    --cc=gregkh@linuxfoundation.org \
    --cc=jun.li@nxp.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-usb@vger.kernel.org \
    --cc=pawell@cadence.com \
    --cc=peter.chen@kernel.org \
    --cc=rogerq@kernel.org \
    --cc=srk@ti.com \
    --cc=stable@vger.kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox