[PATCH 3/3] arm64: dts: allwinner: h616: add YuzukiHD Chameleon support

[Andre Przywara <andre.przywara@arm.com>]

The Chameleon board is an OpenHardware devboard made by YuzukiTsuru.
The form factor resembles the Raspberry Pi Model A boards, though it
differs significantly in its features:

  - Allwinner H618 SoC (4 * Arm Cortex-A53 cores, 1MB L2 cache, 1.4 GHz)
  - between 512MiB and 2GiB DDR3 DRAM
  - up to 128 GiB eMMC flash
  - AXP313a PMIC
  - 100 Mbit/s Ethernet pins on a header
  - XR829 WIFI+Bluetooth chip
  - 4 * USB 2.0 USB-C ports
  - microSD card slot
  - 3.5mm A/V port

Add the devicetree describing the board's peripherals and their
connections.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
 arch/arm64/boot/dts/allwinner/Makefile        |   1 +
 .../sun50i-h618-yuzukihd-chameleon.dts        | 222 ++++++++++++++++++
 2 files changed, 223 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h618-yuzukihd-chameleon.dts

diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index 00bed412ee31c..448698fed5f79 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -48,6 +48,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-longanpi-3h.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-orangepi-zero2w.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-orangepi-zero3.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-transpeed-8k618-t.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-yuzukihd-chameleon.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h700-anbernic-rg35xx-2024.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h700-anbernic-rg35xx-h.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h700-anbernic-rg35xx-plus.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h618-yuzukihd-chameleon.dts b/arch/arm64/boot/dts/allwinner/sun50i-h618-yuzukihd-chameleon.dts
new file mode 100644
index 0000000000000..c60d42130cf79
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h618-yuzukihd-chameleon.dts
@@ -0,0 +1,222 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2024 Arm Ltd.
+ */
+
+/dts-v1/;
+
+#include "sun50i-h616.dtsi"
+#include "sun50i-h616-cpu-opp.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	model = "Yuzuki Chameleon";
+	compatible = "yuzukihd,chameleon", "allwinner,sun50i-h618";
+
+	aliases {
+		ethernet1 = &sdio_wifi;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reg_vcc5v: vcc5v {
+		/* board wide 5V supply directly from the USB-C socket */
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	wifi_pwrseq: pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
+		clock-names = "ext_clock";
+		pinctrl-0 = <&x32clk_fanout_pin>;
+		pinctrl-names = "default";
+		reset-gpios = <&pio 6 11 GPIO_ACTIVE_LOW>; /* PG11 */
+	};
+};
+
+&codec {
+	allwinner,audio-routing = "Line Out", "LINEOUT";
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&ehci2 {
+	status = "okay";
+};
+
+&ehci3 {
+	status = "okay";
+};
+
+&mmc0 {
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;	/* PF6 */
+	disable-wp;
+	vmmc-supply = <&reg_dldo1>;
+	status = "okay";
+};
+
+&mmc1 {
+	bus-width = <4>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	non-removable;
+	vmmc-supply = <&reg_dldo1>;
+	vqmmc-supply = <&reg_dldo1>;
+	status = "okay";
+
+	sdio_wifi: wifi@1 {
+		reg = <1>;
+		interrupt-parent = <&pio>;
+		interrupts = <6 12 IRQ_TYPE_LEVEL_LOW>;  /* PG12 */
+		interrupt-names = "host-wake";
+	};
+};
+
+&mmc2 {
+	bus-width = <8>;
+	cap-mmc-hw-reset;
+	mmc-ddr-3_3v;
+	non-removable;
+	vmmc-supply = <&reg_dldo1>;
+	vqmmc-supply = <&reg_dldo1>;
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&ohci2 {
+	status = "okay";
+};
+
+&ohci3 {
+	status = "okay";
+};
+
+&pio {
+	vcc-pc-supply = <&reg_dldo1>;
+	vcc-pf-supply = <&reg_dldo1>;	/* via VCC_IO */
+	vcc-pg-supply = <&reg_dldo1>;
+	vcc-ph-supply = <&reg_dldo1>;	/* via VCC_IO */
+	vcc-pi-supply = <&reg_dldo1>;
+};
+
+&r_i2c {
+	status = "okay";
+
+	axp313: pmic@36 {
+		compatible = "x-powers,axp313a";
+		reg = <0x36>;
+		#interrupt-cells = <1>;
+		interrupt-controller;
+		interrupt-parent = <&pio>;
+		interrupts = <2 2 IRQ_TYPE_LEVEL_LOW>;	/* PC2 */
+
+		vin1-supply = <&reg_vcc5v>;
+		vin2-supply = <&reg_vcc5v>;
+		vin3-supply = <&reg_vcc5v>;
+
+		regulators {
+			/* Supplies VCC-PLL, so needs to be always on. */
+			reg_aldo1: aldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc1v8";
+			};
+
+			/* Supplies VCC-IO, so needs to be always on. */
+			reg_dldo1: dldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc3v3";
+			};
+
+			reg_dcdc1: dcdc1 {
+				regulator-always-on;
+				regulator-min-microvolt = <810000>;
+				regulator-max-microvolt = <990000>;
+				regulator-name = "vdd-gpu-sys";
+			};
+
+			reg_dcdc2: dcdc2 {
+				regulator-always-on;
+				regulator-min-microvolt = <810000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-name = "vdd-cpu";
+			};
+
+			reg_dcdc3: dcdc3 {
+				regulator-always-on;
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-name = "vdd-dram";
+			};
+		};
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_ph_pins>;
+	status = "okay";
+};
+
+/* Connected to the Bluetooth UART pins of the XR829 Wifi/BT chip. */
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usbotg {
+	/*
+	 * PHY0 pins are connected to a USB-C socket, but a role switch
+	 * is not implemented: both CC pins are pulled to GND.
+	 * The VBUS pins power the device, so a fixed peripheral mode
+	 * is the best choice.
+	 * The board can be powered via GPIOs, in this case port0 *can*
+	 * act as a host (with a cable/adapter ignoring CC), as VBUS is
+	 * then provided by the GPIOs. Any user of this setup would
+	 * need to adjust the DT accordingly: dr_mode set to "host",
+	 * enabling OHCI0 and EHCI0.
+	 */
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 6 18 GPIO_ACTIVE_HIGH>; /* PG18 */
+	usb0_vbus-supply = <&reg_vcc5v>;
+	usb1_vbus-supply = <&reg_vcc5v>;
+	usb2_vbus-supply = <&reg_vcc5v>;
+	usb3_vbus-supply = <&reg_vcc5v>;
+	status = "okay";
+};
-- 
2.46.3