[net-next PATCH v13 00/14] net: dsa: Add Airoha AN8855 support

[net-next PATCH v13 00/14] net: dsa: Add Airoha AN8855 support

[Christian Marangi]

This small series add the initial support for the Airoha AN8855 Switch.

It's a 5 port Gigabit Switch with SGMII/HSGMII upstream port.

This is starting to get in the wild and there are already some router
having this switch chip.

It's conceptually similar to mediatek switch but register and bits
are different. And there is that massive Hell that is the PCS
configuration.
Saddly for that part we have absolutely NO documentation currently.

There is this special thing where PHY needs to be calibrated with values
from the switch efuse. (the thing have a whole cpu timer and MCU)

From v8 Driver is now evaluated with Kernel selftest scripts for DSA:

Additional info about the test bridge_vlan_aware.sh.

It was discovered that the Airoha Switch (and probably the Mediatek one
that produce the same test results) hardcode checking for 802.1ad when
the port is configured in VLAN-Aware mode (aka Security mode).

In such mode, both 802.1q and 802.1ad TPID are checked, hence the
bridge_vlan_aware.sh test fails as packets with 802.1ad TPID are rejected
(in the case where a wrong VLAN ID is forwarded)

This was confirmed by Airoha and multiple try were done to try to
workaround this problem. No solution were found to this as ACL mechanism
can't work on receiving packets and the Switch doesn't support turning off
this.

The current driver is in use from 2 month on OpenWrt with all kind of
scenario confirming working in VLAN bridge. By tweaking the
bridge_vlan_aware.sh test with setting the TPID to 0x9100, the test
correctly pass as packets gets classified as untagged and the default PVID
applied. It's also confirmed that switch correctly parse the 802.1ad tag
and make the packet pass only when allowed by VLAN table rules.

Output local_termination.sh
TEST: lan2: Unicast IPv4 to primary MAC address                     [ OK ]
TEST: lan2: Unicast IPv4 to macvlan MAC address                     [ OK ]
TEST: lan2: Unicast IPv4 to unknown MAC address                     [ OK ]
TEST: lan2: Unicast IPv4 to unknown MAC address, promisc            [ OK ]
TEST: lan2: Unicast IPv4 to unknown MAC address, allmulti           [ OK ]
TEST: lan2: Multicast IPv4 to joined group                          [ OK ]
TEST: lan2: Multicast IPv4 to unknown group                         [XFAIL]
        reception succeeded, but should have failed
TEST: lan2: Multicast IPv4 to unknown group, promisc                [ OK ]
TEST: lan2: Multicast IPv4 to unknown group, allmulti               [ OK ]
TEST: lan2: Multicast IPv6 to joined group                          [ OK ]
TEST: lan2: Multicast IPv6 to unknown group                         [XFAIL]
        reception succeeded, but should have failed
TEST: lan2: Multicast IPv6 to unknown group, promisc                [ OK ]
TEST: lan2: Multicast IPv6 to unknown group, allmulti               [ OK ]
TEST: lan2: 1588v2 over L2 transport, Sync                          [ OK ]
TEST: lan2: 1588v2 over L2 transport, Follow-Up                     [ OK ]
TEST: lan2: 1588v2 over L2 transport, Peer Delay Request            [ OK ]
TEST: lan2: 1588v2 over IPv4, Sync                                  [FAIL]
        reception failed
TEST: lan2: 1588v2 over IPv4, Follow-Up                             [FAIL]
        reception failed
TEST: lan2: 1588v2 over IPv4, Peer Delay Request                    [FAIL]
        reception failed
TEST: lan2: 1588v2 over IPv6, Sync                                  [FAIL]
        reception failed
TEST: lan2: 1588v2 over IPv6, Follow-Up                             [FAIL]
        reception failed
TEST: lan2: 1588v2 over IPv6, Peer Delay Request                    [FAIL]
        reception failed
TEST: vlan_filtering=0 bridge: Unicast IPv4 to primary MAC address   [ OK ]
TEST: vlan_filtering=0 bridge: Unicast IPv4 to macvlan MAC address   [ OK ]
TEST: vlan_filtering=0 bridge: Unicast IPv4 to unknown MAC address   [ OK ]
TEST: vlan_filtering=0 bridge: Unicast IPv4 to unknown MAC address, promisc   [ OK ]
TEST: vlan_filtering=0 bridge: Unicast IPv4 to unknown MAC address, allmulti   [ OK ]
TEST: vlan_filtering=0 bridge: Multicast IPv4 to joined group       [ OK ]
TEST: vlan_filtering=0 bridge: Multicast IPv4 to unknown group      [XFAIL]
        reception succeeded, but should have failed
TEST: vlan_filtering=0 bridge: Multicast IPv4 to unknown group, promisc   [ OK ]
TEST: vlan_filtering=0 bridge: Multicast IPv4 to unknown group, allmulti   [ OK ]
TEST: vlan_filtering=0 bridge: Multicast IPv6 to joined group       [ OK ]
TEST: vlan_filtering=0 bridge: Multicast IPv6 to unknown group      [XFAIL]
        reception succeeded, but should have failed
TEST: vlan_filtering=0 bridge: Multicast IPv6 to unknown group, promisc   [ OK ]
TEST: vlan_filtering=0 bridge: Multicast IPv6 to unknown group, allmulti   [ OK ]
TEST: vlan_filtering=1 bridge: Unicast IPv4 to primary MAC address   [ OK ]
TEST: vlan_filtering=1 bridge: Unicast IPv4 to macvlan MAC address   [ OK ]
TEST: vlan_filtering=1 bridge: Unicast IPv4 to unknown MAC address   [ OK ]
TEST: vlan_filtering=1 bridge: Unicast IPv4 to unknown MAC address, promisc   [ OK ]
TEST: vlan_filtering=1 bridge: Unicast IPv4 to unknown MAC address, allmulti   [ OK ]
TEST: vlan_filtering=1 bridge: Multicast IPv4 to joined group       [ OK ]
TEST: vlan_filtering=1 bridge: Multicast IPv4 to unknown group      [XFAIL]
        reception succeeded, but should have failed
TEST: vlan_filtering=1 bridge: Multicast IPv4 to unknown group, promisc   [ OK ]
TEST: vlan_filtering=1 bridge: Multicast IPv4 to unknown group, allmulti   [ OK ]
TEST: vlan_filtering=1 bridge: Multicast IPv6 to joined group       [ OK ]
TEST: vlan_filtering=1 bridge: Multicast IPv6 to unknown group      [XFAIL]
        reception succeeded, but should have failed
TEST: vlan_filtering=1 bridge: Multicast IPv6 to unknown group, promisc   [ OK ]
TEST: vlan_filtering=1 bridge: Multicast IPv6 to unknown group, allmulti   [ OK ]
TEST: VLAN upper: Unicast IPv4 to primary MAC address               [ OK ]
TEST: VLAN upper: Unicast IPv4 to macvlan MAC address               [ OK ]
TEST: VLAN upper: Unicast IPv4 to unknown MAC address               [ OK ]
TEST: VLAN upper: Unicast IPv4 to unknown MAC address, promisc      [ OK ]
TEST: VLAN upper: Unicast IPv4 to unknown MAC address, allmulti     [ OK ]
TEST: VLAN upper: Multicast IPv4 to joined group                    [ OK ]
TEST: VLAN upper: Multicast IPv4 to unknown group                   [XFAIL]
        reception succeeded, but should have failed
TEST: VLAN upper: Multicast IPv4 to unknown group, promisc          [ OK ]
TEST: VLAN upper: Multicast IPv4 to unknown group, allmulti         [ OK ]
TEST: VLAN upper: Multicast IPv6 to joined group                    [ OK ]
TEST: VLAN upper: Multicast IPv6 to unknown group                   [XFAIL]
        reception succeeded, but should have failed
TEST: VLAN upper: Multicast IPv6 to unknown group, promisc          [ OK ]
TEST: VLAN upper: Multicast IPv6 to unknown group, allmulti         [ OK ]
TEST: VLAN upper: 1588v2 over L2 transport, Sync                    [ OK ]
TEST: VLAN upper: 1588v2 over L2 transport, Follow-Up               [FAIL]
        reception failed
TEST: VLAN upper: 1588v2 over L2 transport, Peer Delay Request      [ OK ]
TEST: VLAN upper: 1588v2 over IPv4, Sync                            [FAIL]
        reception failed
;TEST: VLAN upper: 1588v2 over IPv4, Follow-Up                       [FAIL]
        reception failed
TEST: VLAN upper: 1588v2 over IPv4, Peer Delay Request              [FAIL]
        reception failed
TEST: VLAN upper: 1588v2 over IPv6, Sync                            [FAIL]
        reception failed
TEST: VLAN upper: 1588v2 over IPv6, Follow-Up                       [FAIL]
        reception failed
TEST: VLAN upper: 1588v2 over IPv6, Peer Delay Request              [FAIL]
        reception failed
TEST: VLAN over vlan_filtering=0 bridged port: Unicast IPv4 to primary MAC address   [ OK ]
TEST: VLAN over vlan_filtering=0 bridged port: Unicast IPv4 to macvlan MAC address   [ OK ]
TEST: VLAN over vlan_filtering=0 bridged port: Unicast IPv4 to unknown MAC address   [ OK ]
TEST: VLAN over vlan_filtering=0 bridged port: Unicast IPv4 to unknown MAC address, promisc   [ OK ]
TEST: VLAN over vlan_filtering=0 bridged port: Unicast IPv4 to unknown MAC address, allmulti   [ OK ]
TEST: VLAN over vlan_filtering=0 bridged port: Multicast IPv4 to joined group   [ OK ]
TEST: VLAN over vlan_filtering=0 bridged port: Multicast IPv4 to unknown group   [XFAIL]
        reception succeeded, but should have failed
TEST: VLAN over vlan_filtering=0 bridged port: Multicast IPv4 to unknown group, promisc   [ OK ]
TEST: VLAN over vlan_filtering=0 bridged port: Multicast IPv4 to unknown group, allmulti   [ OK ]
TEST: VLAN over vlan_filtering=0 bridged port: Multicast IPv6 to joined group   [ OK ]
TEST: VLAN over vlan_filtering=0 bridged port: Multicast IPv6 to unknown group   [XFAIL]
        reception succeeded, but should have failed
TEST: VLAN over vlan_filtering=0 bridged port: Multicast IPv6 to unknown group, promisc   [ OK ]
TEST: VLAN over vlan_filtering=0 bridged port: Multicast IPv6 to unknown group, allmulti   [ OK ]
TEST: VLAN over vlan_filtering=0 bridged port: 1588v2 over L2 transport, Sync   [ OK ]
TEST: VLAN over vlan_filtering=0 bridged port: 1588v2 over L2 transport, Follow-Up   [ OK ]
TEST: VLAN over vlan_filtering=0 bridged port: 1588v2 over L2 transport, Peer Delay Request   [ OK ]
TEST: VLAN over vlan_filtering=0 bridged port: 1588v2 over IPv4, Sync   [FAIL]
        reception failed
TEST: VLAN over vlan_filtering=0 bridged port: 1588v2 over IPv4, Follow-Up   [FAIL]
        reception failed
TEST: VLAN over vlan_filtering=0 bridged port: 1588v2 over IPv4, Peer Delay Request   [FAIL]
        reception failed
TEST: VLAN over vlan_filtering=0 bridged port: 1588v2 over IPv6, Sync   [FAIL]
        reception failed
TEST: VLAN over vlan_filtering=0 bridged port: 1588v2 over IPv6, Follow-Up   [FAIL]
        reception failed
TEST: VLAN over vlan_filtering=0 bridged port: 1588v2 over IPv6, Peer Delay Request   [FAIL]
        reception failed
TEST: VLAN over vlan_filtering=1 bridged port: Unicast IPv4 to primary MAC address   [ OK ]
TEST: VLAN over vlan_filtering=1 bridged port: Unicast IPv4 to macvlan MAC address   [ OK ]
TEST: VLAN over vlan_filtering=1 bridged port: Unicast IPv4 to unknown MAC address   [FAIL]
        reception succeeded, but should have failed
TEST: VLAN over vlan_filtering=1 bridged port: Unicast IPv4 to unknown MAC address, promisc   [ OK ]
TEST: VLAN over vlan_filtering=1 bridged port: Unicast IPv4 to unknown MAC address, allmulti   [FAIL]
        reception succeeded, but should have failed
TEST: VLAN over vlan_filtering=1 bridged port: Multicast IPv4 to joined group   [ OK ]
TEST: VLAN over vlan_filtering=1 bridged port: Multicast IPv4 to unknown group   [XFAIL]
        reception succeeded, but should have failed
TEST: VLAN over vlan_filtering=1 bridged port: Multicast IPv4 to unknown group, promisc   [ OK ]
TEST: VLAN over vlan_filtering=1 bridged port: Multicast IPv4 to unknown group, allmulti   [ OK ]
TEST: VLAN over vlan_filtering=1 bridged port: Multicast IPv6 to joined group   [ OK ]
TEST: VLAN over vlan_filtering=1 bridged port: Multicast IPv6 to unknown group   [XFAIL]
        reception succeeded, but should have failed
TEST: VLAN over vlan_filtering=1 bridged port: Multicast IPv6 to unknown group, promisc   [ OK ]
TEST: VLAN over vlan_filtering=1 bridged port: Multicast IPv6 to unknown group, allmulti   [ OK ]
TEST: VLAN over vlan_filtering=1 bridged port: 1588v2 over L2 transport, Sync   [ OK ]
TEST: VLAN over vlan_filtering=1 bridged port: 1588v2 over L2 transport, Follow-Up   [ OK ]
TEST: VLAN over vlan_filtering=1 bridged port: 1588v2 over L2 transport, Peer Delay Request   [ OK ]
TEST: VLAN over vlan_filtering=1 bridged port: 1588v2 over IPv4, Sync   [FAIL]
        reception failed
TEST: VLAN over vlan_filtering=1 bridged port: 1588v2 over IPv4, Follow-Up   [FAIL]
        reception failed
TEST: VLAN over vlan_filtering=1 bridged port: 1588v2 over IPv4, Peer Delay Request   [FAIL]
        reception failed
TEST: VLAN over vlan_filtering=1 bridged port: 1588v2 over IPv6, Sync   [FAIL]
        reception failed
TEST: VLAN over vlan_filtering=1 bridged port: 1588v2 over IPv6, Follow-Up   [FAIL]
        reception failed
TEST: VLAN over vlan_filtering=1 bridged port: 1588v2 over IPv6, Peer Delay Request   [FAIL]
        reception failed
TEST: VLAN over vlan_filtering=0 bridge: Unicast IPv4 to primary MAC address   [ OK ]
TEST: VLAN over vlan_filtering=0 bridge: Unicast IPv4 to macvlan MAC address   [ OK ]
TEST: VLAN over vlan_filtering=0 bridge: Unicast IPv4 to unknown MAC address   [ OK ]
TEST: VLAN over vlan_filtering=0 bridge: Unicast IPv4 to unknown MAC address, promisc   [ OK ]
TEST: VLAN over vlan_filtering=0 bridge: Unicast IPv4 to unknown MAC address, allmulti   [ OK ]
TEST: VLAN over vlan_filtering=0 bridge: Multicast IPv4 to joined group   [ OK ]
TEST: VLAN over vlan_filtering=0 bridge: Multicast IPv4 to unknown group   [XFAIL]
        reception succeeded, but should have failed
TEST: VLAN over vlan_filtering=0 bridge: Multicast IPv4 to unknown group, promisc   [ OK ]
TEST: VLAN over vlan_filtering=0 bridge: Multicast IPv4 to unknown group, allmulti   [ OK ]
TEST: VLAN over vlan_filtering=0 bridge: Multicast IPv6 to joined group   [ OK ]
TEST: VLAN over vlan_filtering=0 bridge: Multicast IPv6 to unknown group   [XFAIL]
        reception succeeded, but should have failed
TEST: VLAN over vlan_filtering=0 bridge: Multicast IPv6 to unknown group, promisc   [ OK ]
TEST: VLAN over vlan_filtering=0 bridge: Multicast IPv6 to unknown group, allmulti   [ OK ]
TEST: VLAN over vlan_filtering=1 bridge: Unicast IPv4 to primary MAC address   [ OK ]
TEST: VLAN over vlan_filtering=1 bridge: Unicast IPv4 to macvlan MAC address   [ OK ]
TEST: VLAN over vlan_filtering=1 bridge: Unicast IPv4 to unknown MAC address   [ OK ]
TEST: VLAN over vlan_filtering=1 bridge: Unicast IPv4 to unknown MAC address, promisc   [ OK ]
TEST: VLAN over vlan_filtering=1 bridge: Unicast IPv4 to unknown MAC address, allmulti   [ OK ]
TEST: VLAN over vlan_filtering=1 bridge: Multicast IPv4 to joined group   [ OK ]
TEST: VLAN over vlan_filtering=1 bridge: Multicast IPv4 to unknown group   [XFAIL]
        reception succeeded, but should have failed
TEST: VLAN over vlan_filtering=1 bridge: Multicast IPv4 to unknown group, promisc   [ OK ]
TEST: VLAN over vlan_filtering=1 bridge: Multicast IPv4 to unknown group, allmulti   [ OK ]
TEST: VLAN over vlan_filtering=1 bridge: Multicast IPv6 to joined group   [ OK ]
TEST: VLAN over vlan_filtering=1 bridge: Multicast IPv6 to unknown group   [XFAIL]
        reception succeeded, but should have failed
TEST: VLAN over vlan_filtering=1 bridge: Multicast IPv6 to unknown group, promisc   [ OK ]
TEST: VLAN over vlan_filtering=1 bridge: Multicast IPv6 to unknown group, allmulti   [ OK ]

Output bridge_vlan_unaware.sh
TEST: ping                                                          [ OK ]
TEST: ping6                                                         [ OK ]
TEST: FDB learning                                                  [ OK ]
TEST: Unknown unicast flood                                         [ OK ]
TEST: Unregistered multicast flood                                  [ OK ]

Output bridge_vlan_aware.sh
TEST: ping                                                          [ OK ]
TEST: ping6                                                         [ OK ]
TEST: FDB learning                                                  [ OK ]
TEST: Unknown unicast flood                                         [ OK ]
TEST: Unregistered multicast flood                                  [ OK ]
INFO: Add and delete a VLAN on bridge port lan2
TEST: ping                                                          [ OK ]
TEST: ping6                                                         [ OK ]
TEST: Externally learned FDB entry - ageing & roaming               [ OK ]
TEST: FDB entry in PVID for VLAN-tagged with other TPID             [FAIL]
        FDB entry was not learned when it should
TEST: Reception of VLAN with other TPID as untagged                 [FAIL]
        Packet was not forwarded when it should
TEST: Reception of VLAN with other TPID as untagged (no PVID)       [FAIL]
        Packet was forwarded when should not

[ For Vladimir, I still have to implement fdb_isolation but posting to
start the ball rolling for the multiple subsystem this patch affect
and for the dubious DT schema ]

Changes v13:
- Reimplement tx_lpi OPs
- Rework mdio-regmap to internally encode/decode address
- Fix error in Documentation
- Drop ext-surge property (assume calibration with declared nvmem cell)
- Fix comments from Lee on MFD driver
- Improve print error and drop extra space in DSA driver
Changes v12:
- Update on top of net-next
- Add additional info on conver-letter about slefttests and HW limitation
- Introduce mdio-regmap generalization for multiple address
- Drop dev flags and define PHY calibration in PHY node directly
Changes v11:
- Address reviews from Christophe (spell mistake + dev_err_probe)
- Fix kconfig dependency for MFD driver (depends on MDIO_DEVICE instead of MDIO)
  (indirectly fix link error for mdio APIs)
- Fix copy-paste error for MFD driver of_table
- Fix compilation error for PHY (move NVMEM to .config)
- Drop unneeded NVMEM node from MDIO example schema (from Andrew)
- Adapt MFD example schema to MDIO reg property restrictions
Changes v10:
- Entire rework to MFD + split to MDIO, EFUSE, SWITCH separate drivers
- Drop EEE OPs (while Russell finish RFC for EEE changes)
- Use new pcs_inpand OPs
- Drop AN restart function and move to pcs_config
- Enable assisted_learning and disable CPU learn (preparation for fdb_isolation)
- Move EFUSE read in Internal PHY driver to .config to handle EPROBE_DEFER
  (needed now that NVMEM driver is register externally instead of internally to switch
   node)
Changes v9:
- Error out on using 5G speed as currently not supported
- Add missing MAC_2500FD in phylink mac_capabilities
- Add comment and improve if condition for an8855_phylink_mac_config
Changes v8:
- Add port Fast Age support
- Add support for Port Isolation
- Use correct register for Learning Disable
- Add support for Ageing Time OP
- Set default PVID to 0 by default
- Add mdb OPs
- Add port change MTU
- Fix support for Upper VLAN
Changes v7:
- Fix devm_dsa_register_switch wrong export symbol
Changes v6:
- Drop standard MIB and handle with ethtool OPs (as requested by Jakub)
- Cosmetic: use bool instead of 0 or 1
Changes v5:
- Add devm_dsa_register_switch() patch
- Add Reviewed-by tag for DT patch
Changes v4:
- Set regmap readable_table static (mute compilation warning)
- Add support for port_bridge flags (LEARNING, FLOOD)
- Reset fdb struct in fdb_dump
- Drop support_asym_pause in port_enable
- Add define for get_phy_flags
- Fix bug for port not inititially part of a bridge
  (in an8855_setup the port matrix was always cleared but
   the CPU port was never initially added)
- Disable learning and flood for user port by default
- Set CPU port to flood and learning by default
- Correctly AND force duplex and flow control in an8855_phylink_mac_link_up
- Drop RGMII from pcs_config
- Check ret in "Disable AN if not in autoneg"
- Use devm_mutex_init
- Fix typo for AN8855_PORT_CHECK_MODE
- Better define AN8855_STP_LISTENING = AN8855_STP_BLOCKING
- Fix typo in AN8855_PHY_EN_DOWN_SHIFT
- Use paged helper for PHY
- Skip calibration in config_init if priv not defined
Changes v3:
- Out of RFC
- Switch PHY code to select_page API
- Better describe masks and bits in PHY driver for ADC register
- Drop raw values and use define for mii read/write
- Switch to absolute PHY address
- Replace raw values with mask and bits for pcs_config
- Fix typo for ext-surge property name
- Drop support for relocating Switch base PHY address on the bus
Changes v2:
- Drop mutex guard patch
- Drop guard usage in DSA driver
- Use __mdiobus_write/read
- Check return condition and return errors for mii read/write
- Fix wrong logic for EEE
- Fix link_down (don't force link down with autoneg)
- Fix forcing speed on sgmii autoneg
- Better document link speed for sgmii reg
- Use standard define for sgmii reg
- Imlement nvmem support to expose switch EFUSE
- Rework PHY calibration with the use of NVMEM producer/consumer
- Update DT with new NVMEM property
- Move aneg validation for 2500-basex in pcs_config
- Move r50Ohm table and function to PHY driver

Christian Marangi (14):
  dt-bindings: nvmem: Document support for Airoha AN8855 Switch EFUSE
  dt-bindings: net: Document support for Airoha AN8855 Switch Virtual
    MDIO
  dt-bindings: net: dsa: Document support for Airoha AN8855 DSA Switch
  dt-bindings: net: Document support for AN8855 Switch Internal PHY
  dt-bindings: mfd: Document support for Airoha AN8855 Switch SoC
  net: mdio: regmap: prepare support for multiple valid addr
  net: mdio: regmap: add support for C45 read/write
  net: mdio: regmap: add support for multiple valid addr
  net: mdio: regmap: add OF support
  mfd: an8855: Add support for Airoha AN8855 Switch MFD
  net: mdio: Add Airoha AN8855 Switch MDIO Passtrough
  nvmem: an8855: Add support for Airoha AN8855 Switch EFUSE
  net: dsa: Add Airoha AN8855 5-Port Gigabit DSA Switch driver
  net: phy: Add Airoha AN8855 Internal Switch Gigabit PHY

 .../bindings/mfd/airoha,an8855.yaml           |  182 ++
 .../bindings/net/airoha,an8855-mdio.yaml      |   56 +
 .../bindings/net/airoha,an8855-phy.yaml       |   83 +
 .../net/dsa/airoha,an8855-switch.yaml         |   86 +
 .../bindings/nvmem/airoha,an8855-efuse.yaml   |  123 +
 MAINTAINERS                                   |   18 +
 drivers/mfd/Kconfig                           |   12 +
 drivers/mfd/Makefile                          |    1 +
 drivers/mfd/airoha-an8855.c                   |  429 +++
 drivers/net/dsa/Kconfig                       |    9 +
 drivers/net/dsa/Makefile                      |    1 +
 drivers/net/dsa/an8855.c                      | 2395 +++++++++++++++++
 drivers/net/dsa/an8855.h                      |  773 ++++++
 drivers/net/mdio/Kconfig                      |   10 +
 drivers/net/mdio/Makefile                     |    1 +
 drivers/net/mdio/mdio-an8855.c                |   49 +
 drivers/net/mdio/mdio-regmap.c                |  188 +-
 drivers/net/phy/Kconfig                       |    5 +
 drivers/net/phy/Makefile                      |    1 +
 drivers/net/phy/air_an8855.c                  |  261 ++
 drivers/nvmem/Kconfig                         |   11 +
 drivers/nvmem/Makefile                        |    2 +
 drivers/nvmem/an8855-efuse.c                  |   63 +
 include/linux/mdio/mdio-regmap.h              |   16 +
 24 files changed, 4761 insertions(+), 14 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/mfd/airoha,an8855.yaml
 create mode 100644 Documentation/devicetree/bindings/net/airoha,an8855-mdio.yaml
 create mode 100644 Documentation/devicetree/bindings/net/airoha,an8855-phy.yaml
 create mode 100644 Documentation/devicetree/bindings/net/dsa/airoha,an8855-switch.yaml
 create mode 100644 Documentation/devicetree/bindings/nvmem/airoha,an8855-efuse.yaml
 create mode 100644 drivers/mfd/airoha-an8855.c
 create mode 100644 drivers/net/dsa/an8855.c
 create mode 100644 drivers/net/dsa/an8855.h
 create mode 100644 drivers/net/mdio/mdio-an8855.c
 create mode 100644 drivers/net/phy/air_an8855.c
 create mode 100644 drivers/nvmem/an8855-efuse.c

-- 
2.48.1

[net-next PATCH v13 01/14] dt-bindings: nvmem: Document support for Airoha AN8855 Switch EFUSE

[Christian Marangi]

Document support for Airoha AN8855 Switch EFUSE used to calibrate
internal PHYs and store additional configuration info.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
---
 .../bindings/nvmem/airoha,an8855-efuse.yaml   | 123 ++++++++++++++++++
 MAINTAINERS                                   |   8 ++
 2 files changed, 131 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/nvmem/airoha,an8855-efuse.yaml

diff --git a/Documentation/devicetree/bindings/nvmem/airoha,an8855-efuse.yaml b/Documentation/devicetree/bindings/nvmem/airoha,an8855-efuse.yaml
new file mode 100644
index 000000000000..9802d9ea2176
--- /dev/null
+++ b/Documentation/devicetree/bindings/nvmem/airoha,an8855-efuse.yaml
@@ -0,0 +1,123 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/nvmem/airoha,an8855-efuse.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Airoha AN8855 Switch EFUSE
+
+maintainers:
+  - Christian Marangi <ansuelsmth@gmail.com>
+
+description:
+  Airoha AN8855 EFUSE used to calibrate internal PHYs and store additional
+  configuration info.
+
+$ref: nvmem.yaml#
+
+properties:
+  compatible:
+    const: airoha,an8855-efuse
+
+  '#nvmem-cell-cells':
+    const: 0
+
+required:
+  - compatible
+  - '#nvmem-cell-cells'
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    efuse {
+        compatible = "airoha,an8855-efuse";
+
+        #nvmem-cell-cells = <0>;
+
+        nvmem-layout {
+            compatible = "fixed-layout";
+            #address-cells = <1>;
+            #size-cells = <1>;
+
+            shift_sel_port0_tx_a: shift-sel-port0-tx-a@c {
+               reg = <0xc 0x4>;
+            };
+
+            shift_sel_port0_tx_b: shift-sel-port0-tx-b@10 {
+                reg = <0x10 0x4>;
+            };
+
+            shift_sel_port0_tx_c: shift-sel-port0-tx-c@14 {
+                reg = <0x14 0x4>;
+            };
+
+            shift_sel_port0_tx_d: shift-sel-port0-tx-d@18 {
+               reg = <0x18 0x4>;
+            };
+
+            shift_sel_port1_tx_a: shift-sel-port1-tx-a@1c {
+               reg = <0x1c 0x4>;
+            };
+
+            shift_sel_port1_tx_b: shift-sel-port1-tx-b@20 {
+               reg = <0x20 0x4>;
+            };
+
+            shift_sel_port1_tx_c: shift-sel-port1-tx-c@24 {
+               reg = <0x24 0x4>;
+            };
+
+            shift_sel_port1_tx_d: shift-sel-port1-tx-d@28 {
+               reg = <0x28 0x4>;
+            };
+
+            shift_sel_port2_tx_a: shift-sel-port2-tx-a@2c {
+                reg = <0x2c 0x4>;
+            };
+
+            shift_sel_port2_tx_b: shift-sel-port2-tx-b@30 {
+                reg = <0x30 0x4>;
+            };
+
+            shift_sel_port2_tx_c: shift-sel-port2-tx-c@34 {
+                reg = <0x34 0x4>;
+            };
+
+            shift_sel_port2_tx_d: shift-sel-port2-tx-d@38 {
+                reg = <0x38 0x4>;
+            };
+
+            shift_sel_port3_tx_a: shift-sel-port3-tx-a@4c {
+                reg = <0x4c 0x4>;
+            };
+
+            shift_sel_port3_tx_b: shift-sel-port3-tx-b@50 {
+                reg = <0x50 0x4>;
+            };
+
+            shift_sel_port3_tx_c: shift-sel-port3-tx-c@54 {
+               reg = <0x54 0x4>;
+            };
+
+            shift_sel_port3_tx_d: shift-sel-port3-tx-d@58 {
+               reg = <0x58 0x4>;
+            };
+
+            shift_sel_port4_tx_a: shift-sel-port4-tx-a@5c {
+                reg = <0x5c 0x4>;
+            };
+
+            shift_sel_port4_tx_b: shift-sel-port4-tx-b@60 {
+                reg = <0x60 0x4>;
+            };
+
+            shift_sel_port4_tx_c: shift-sel-port4-tx-c@64 {
+                reg = <0x64 0x4>;
+            };
+
+            shift_sel_port4_tx_d: shift-sel-port4-tx-d@68 {
+                reg = <0x68 0x4>;
+            };
+        };
+    };
diff --git a/MAINTAINERS b/MAINTAINERS
index ffbcd072fb14..576fa7eb7b55 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -719,6 +719,14 @@ S:	Supported
 F:	fs/aio.c
 F:	include/linux/*aio*.h
 
+AIROHA DSA DRIVER
+M:	Christian Marangi <ansuelsmth@gmail.com>
+L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
+L:	linux-mediatek@lists.infradead.org (moderated for non-subscribers)
+L:	netdev@vger.kernel.org
+S:	Maintained
+F:	Documentation/devicetree/bindings/nvmem/airoha,an8855-efuse.yaml
+
 AIROHA ETHERNET DRIVER
 M:	Lorenzo Bianconi <lorenzo@kernel.org>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-- 
2.48.1

[net-next PATCH v13 02/14] dt-bindings: net: Document support for Airoha AN8855 Switch Virtual MDIO

[Christian Marangi]

Document support for Airoha AN8855 Virtual MDIO Passtrough. This is needed
as AN8855 require special handling as the same address on the MDIO bus is
shared for both Switch and PHY and special handling for the page
configuration is needed to switch accessing to Switch address space
or PHY.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
---
 .../bindings/net/airoha,an8855-mdio.yaml      | 56 +++++++++++++++++++
 MAINTAINERS                                   |  1 +
 2 files changed, 57 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/net/airoha,an8855-mdio.yaml

diff --git a/Documentation/devicetree/bindings/net/airoha,an8855-mdio.yaml b/Documentation/devicetree/bindings/net/airoha,an8855-mdio.yaml
new file mode 100644
index 000000000000..3078277bf478
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/airoha,an8855-mdio.yaml
@@ -0,0 +1,56 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/airoha,an8855-mdio.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Airoha AN8855 MDIO Passtrough
+
+maintainers:
+  - Christian Marangi <ansuelsmth@gmail.com>
+
+description:
+  Airoha AN8855 Virtual MDIO Passtrough. This is needed as AN8855
+  require special handling as the same address on the MDIO bus is
+  shared for both Switch and PHY and special handling for the page
+  configuration is needed to switch accessing to Switch address space
+  or PHY.
+
+$ref: /schemas/net/mdio.yaml#
+
+properties:
+  compatible:
+    const: airoha,an8855-mdio
+
+required:
+  - compatible
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    mdio {
+        compatible = "airoha,an8855-mdio";
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        internal_phy1: phy@1 {
+            reg = <1>;
+        };
+
+        internal_phy2: phy@2 {
+            reg = <2>;
+        };
+
+        internal_phy3: phy@3 {
+            reg = <3>;
+        };
+
+        internal_phy4: phy@4 {
+            reg = <4>;
+        };
+
+        internal_phy5: phy@5 {
+            reg = <5>;
+        };
+    };
diff --git a/MAINTAINERS b/MAINTAINERS
index 576fa7eb7b55..1e8055b5e162 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -725,6 +725,7 @@ L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 L:	linux-mediatek@lists.infradead.org (moderated for non-subscribers)
 L:	netdev@vger.kernel.org
 S:	Maintained
+F:	Documentation/devicetree/bindings/net/airoha,an8855-mdio.yaml
 F:	Documentation/devicetree/bindings/nvmem/airoha,an8855-efuse.yaml
 
 AIROHA ETHERNET DRIVER
-- 
2.48.1

[net-next PATCH v13 03/14] dt-bindings: net: dsa: Document support for Airoha AN8855 DSA Switch

[Christian Marangi]

Document support for Airoha AN8855 5-port Gigabit Switch.

It does expose the 5 Internal PHYs on the MDIO bus and each port
can access the Switch register space by configurting the PHY page.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
---
 .../net/dsa/airoha,an8855-switch.yaml         | 86 +++++++++++++++++++
 MAINTAINERS                                   |  1 +
 2 files changed, 87 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/net/dsa/airoha,an8855-switch.yaml

diff --git a/Documentation/devicetree/bindings/net/dsa/airoha,an8855-switch.yaml b/Documentation/devicetree/bindings/net/dsa/airoha,an8855-switch.yaml
new file mode 100644
index 000000000000..fbb9219fadae
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/airoha,an8855-switch.yaml
@@ -0,0 +1,86 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/dsa/airoha,an8855-switch.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Airoha AN8855 Gigabit Switch
+
+maintainers:
+  - Christian Marangi <ansuelsmth@gmail.com>
+
+description: >
+  Airoha AN8855 is a 5-port Gigabit Switch.
+
+  It does expose the 5 Internal PHYs on the MDIO bus and each port
+  can access the Switch register space by configurting the PHY page.
+
+$ref: dsa.yaml#/$defs/ethernet-ports
+
+properties:
+  compatible:
+    const: airoha,an8855-switch
+
+required:
+  - compatible
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    ethernet-switch {
+        compatible = "airoha,an8855-switch";
+
+        ports {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            port@0 {
+                reg = <0>;
+                label = "lan1";
+                phy-mode = "internal";
+                phy-handle = <&internal_phy1>;
+            };
+
+            port@1 {
+                reg = <1>;
+                label = "lan2";
+                phy-mode = "internal";
+                phy-handle = <&internal_phy2>;
+            };
+
+            port@2 {
+                reg = <2>;
+                label = "lan3";
+                phy-mode = "internal";
+                phy-handle = <&internal_phy3>;
+            };
+
+            port@3 {
+                reg = <3>;
+                label = "lan4";
+                phy-mode = "internal";
+                phy-handle = <&internal_phy4>;
+            };
+
+            port@4 {
+                reg = <4>;
+                label = "wan";
+                phy-mode = "internal";
+                phy-handle = <&internal_phy5>;
+            };
+
+            port@5 {
+                reg = <5>;
+                label = "cpu";
+                ethernet = <&gmac0>;
+                phy-mode = "2500base-x";
+
+                fixed-link {
+                    speed = <2500>;
+                    full-duplex;
+                    pause;
+                };
+            };
+        };
+    };
diff --git a/MAINTAINERS b/MAINTAINERS
index 1e8055b5e162..696ad8465ea8 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -726,6 +726,7 @@ L:	linux-mediatek@lists.infradead.org (moderated for non-subscribers)
 L:	netdev@vger.kernel.org
 S:	Maintained
 F:	Documentation/devicetree/bindings/net/airoha,an8855-mdio.yaml
+F:	Documentation/devicetree/bindings/net/dsa/airoha,an8855-switch.yaml
 F:	Documentation/devicetree/bindings/nvmem/airoha,an8855-efuse.yaml
 
 AIROHA ETHERNET DRIVER
-- 
2.48.1

[net-next PATCH v13 04/14] dt-bindings: net: Document support for AN8855 Switch Internal PHY

[Christian Marangi]

Document support for AN8855 Switch Internal PHY.

Airoha AN8855 is a 5-port Gigabit Switch that expose the Internal
PHYs on the MDIO bus.

Each PHY might need to be calibrated to correctly work with the
use of the eFUSE provided by the Switch SoC. This can be enabled by
defining in the PHY node the NVMEM cell properties.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
---
 .../bindings/net/airoha,an8855-phy.yaml       | 83 +++++++++++++++++++
 MAINTAINERS                                   |  1 +
 2 files changed, 84 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/net/airoha,an8855-phy.yaml

diff --git a/Documentation/devicetree/bindings/net/airoha,an8855-phy.yaml b/Documentation/devicetree/bindings/net/airoha,an8855-phy.yaml
new file mode 100644
index 000000000000..d2f86116badf
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/airoha,an8855-phy.yaml
@@ -0,0 +1,83 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/airoha,an8855-phy.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Airoha AN8855 Switch Internal PHY
+
+maintainers:
+  - Christian Marangi <ansuelsmth@gmail.com>
+
+description: >
+  Airoha AN8855 is a 5-port Gigabit Switch that expose the Internal
+  PHYs on the MDIO bus.
+
+  Each PHY might need to be calibrated to correctly work with the
+  use of the eFUSE provided by the Switch SoC.
+
+allOf:
+  - $ref: ethernet-phy.yaml#
+
+select:
+  properties:
+    compatible:
+      contains:
+        enum:
+          - ethernet-phy-idc0ff.0410
+  required:
+    - compatible
+
+properties:
+  reg:
+    maxItems: 1
+
+  nvmem-cells:
+    items:
+      - description: phandle to SoC eFUSE tx_a
+      - description: phandle to SoC eFUSE tx_b
+      - description: phandle to SoC eFUSE tx_c
+      - description: phandle to SoC eFUSE tx_d
+
+  nvmem-cell-names:
+    items:
+      - const: tx_a
+      - const: tx_b
+      - const: tx_c
+      - const: tx_d
+
+required:
+  - compatible
+  - reg
+
+dependentRequired:
+  nvmem-cells: [ nvmem-cell-names ]
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    mdio {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        ethernet-phy@1 {
+            compatible = "ethernet-phy-idc0ff.0410",
+                         "ethernet-phy-ieee802.3-c45";
+
+            reg = <1>;
+        };
+
+        ethernet-phy@2 {
+            compatible = "ethernet-phy-idc0ff.0410",
+                         "ethernet-phy-ieee802.3-c45";
+
+            reg = <2>;
+
+            nvmem-cells = <&shift_sel_port0_tx_a>,
+                          <&shift_sel_port0_tx_b>,
+                          <&shift_sel_port0_tx_c>,
+                          <&shift_sel_port0_tx_d>;
+            nvmem-cell-names = "tx_a", "tx_b", "tx_c", "tx_d";
+        };
+    };
diff --git a/MAINTAINERS b/MAINTAINERS
index 696ad8465ea8..45f4bb8deb0d 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -726,6 +726,7 @@ L:	linux-mediatek@lists.infradead.org (moderated for non-subscribers)
 L:	netdev@vger.kernel.org
 S:	Maintained
 F:	Documentation/devicetree/bindings/net/airoha,an8855-mdio.yaml
+F:	Documentation/devicetree/bindings/net/airoha,an8855-phy.yaml
 F:	Documentation/devicetree/bindings/net/dsa/airoha,an8855-switch.yaml
 F:	Documentation/devicetree/bindings/nvmem/airoha,an8855-efuse.yaml
 
-- 
2.48.1

[net-next PATCH v13 05/14] dt-bindings: mfd: Document support for Airoha AN8855 Switch SoC

[Christian Marangi]

Document support for Airoha AN8855 Switch SoC. This SoC expose various
peripherals like an Ethernet Switch, a NVMEM provider and Ethernet PHYs.

It does also support i2c and timers but those are not currently
supported/used.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
---
 .../bindings/mfd/airoha,an8855.yaml           | 182 ++++++++++++++++++
 MAINTAINERS                                   |   1 +
 2 files changed, 183 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mfd/airoha,an8855.yaml

diff --git a/Documentation/devicetree/bindings/mfd/airoha,an8855.yaml b/Documentation/devicetree/bindings/mfd/airoha,an8855.yaml
new file mode 100644
index 000000000000..a59a23056b3a
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/airoha,an8855.yaml
@@ -0,0 +1,182 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/airoha,an8855.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Airoha AN8855 Switch SoC
+
+maintainers:
+  - Christian Marangi <ansuelsmth@gmail.com>
+
+description: >
+  Airoha AN8855 Switch is a SoC that expose various peripherals like an
+  Ethernet Switch, a NVMEM provider and Ethernet PHYs.
+
+  It does also support i2c and timers but those are not currently
+  supported/used.
+
+properties:
+  compatible:
+    const: airoha,an8855
+
+  reg:
+    maxItems: 1
+
+  reset-gpios: true
+
+  efuse:
+    type: object
+    $ref: /schemas/nvmem/airoha,an8855-efuse.yaml
+    description:
+      EFUSE exposed by the Airoha AN8855 Switch. This child node definition
+      should follow the bindings specified in
+      Documentation/devicetree/bindings/nvmem/airoha,an8855-efuse.yaml
+
+  ethernet-switch:
+    type: object
+    $ref: /schemas/net/dsa/airoha,an8855-switch.yaml
+    description:
+      Switch exposed by the Airoha AN8855 Switch. This child node definition
+      should follow the bindings specified in
+      Documentation/devicetree/bindings/net/dsa/airoha,an8855-switch.yaml
+
+  mdio:
+    type: object
+    $ref: /schemas/net/airoha,an8855-mdio.yaml
+    description:
+      MDIO exposed by the Airoha AN8855 Switch. This child node definition
+      should follow the bindings specified in
+      Documentation/devicetree/bindings/net/airoha,an8855-mdio.yaml
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    mdio {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        soc@1 {
+            compatible = "airoha,an8855";
+            reg = <1>;
+
+            reset-gpios = <&pio 39 0>;
+
+            efuse {
+                compatible = "airoha,an8855-efuse";
+
+                #nvmem-cell-cells = <0>;
+
+                nvmem-layout {
+                    compatible = "fixed-layout";
+                    #address-cells = <1>;
+                    #size-cells = <1>;
+
+                    shift_sel_port0_tx_a: shift-sel-port0-tx-a@c {
+                       reg = <0xc 0x4>;
+                    };
+
+                    shift_sel_port0_tx_b: shift-sel-port0-tx-b@10 {
+                        reg = <0x10 0x4>;
+                    };
+
+                    shift_sel_port0_tx_c: shift-sel-port0-tx-c@14 {
+                        reg = <0x14 0x4>;
+                    };
+
+                    shift_sel_port0_tx_d: shift-sel-port0-tx-d@18 {
+                       reg = <0x18 0x4>;
+                    };
+
+                    shift_sel_port1_tx_a: shift-sel-port1-tx-a@1c {
+                        reg = <0x1c 0x4>;
+                    };
+
+                    shift_sel_port1_tx_b: shift-sel-port1-tx-b@20 {
+                        reg = <0x20 0x4>;
+                    };
+
+                    shift_sel_port1_tx_c: shift-sel-port1-tx-c@24 {
+                       reg = <0x24 0x4>;
+                    };
+
+                    shift_sel_port1_tx_d: shift-sel-port1-tx-d@28 {
+                        reg = <0x28 0x4>;
+                    };
+                };
+            };
+
+            ethernet-switch {
+                compatible = "airoha,an8855-switch";
+
+                ports {
+                    #address-cells = <1>;
+                    #size-cells = <0>;
+
+                    port@0 {
+                        reg = <0>;
+                        label = "lan1";
+                        phy-mode = "internal";
+                        phy-handle = <&internal_phy1>;
+                    };
+
+                    port@1 {
+                        reg = <1>;
+                        label = "lan2";
+                        phy-mode = "internal";
+                        phy-handle = <&internal_phy2>;
+                    };
+
+                    port@5 {
+                        reg = <5>;
+                        label = "cpu";
+                        ethernet = <&gmac0>;
+                        phy-mode = "2500base-x";
+
+                        fixed-link {
+                            speed = <2500>;
+                            full-duplex;
+                            pause;
+                        };
+                    };
+                };
+            };
+
+            mdio {
+                compatible = "airoha,an8855-mdio";
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                internal_phy1: phy@1 {
+                  compatible = "ethernet-phy-idc0ff.0410",
+                               "ethernet-phy-ieee802.3-c45";
+                  reg = <1>;
+
+                  nvmem-cells = <&shift_sel_port0_tx_a>,
+                      <&shift_sel_port0_tx_b>,
+                      <&shift_sel_port0_tx_c>,
+                      <&shift_sel_port0_tx_d>;
+                  nvmem-cell-names = "tx_a", "tx_b", "tx_c", "tx_d";
+                };
+
+                internal_phy2: phy@2 {
+                  compatible = "ethernet-phy-idc0ff.0410",
+                               "ethernet-phy-ieee802.3-c45";
+                  reg = <2>;
+
+                  nvmem-cells = <&shift_sel_port1_tx_a>,
+                      <&shift_sel_port1_tx_b>,
+                      <&shift_sel_port1_tx_c>,
+                      <&shift_sel_port1_tx_d>;
+                  nvmem-cell-names = "tx_a", "tx_b", "tx_c", "tx_d";
+                };
+            };
+        };
+    };
diff --git a/MAINTAINERS b/MAINTAINERS
index 45f4bb8deb0d..65709e47adc7 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -725,6 +725,7 @@ L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 L:	linux-mediatek@lists.infradead.org (moderated for non-subscribers)
 L:	netdev@vger.kernel.org
 S:	Maintained
+F:	Documentation/devicetree/bindings/mfd/airoha,an8855.yaml
 F:	Documentation/devicetree/bindings/net/airoha,an8855-mdio.yaml
 F:	Documentation/devicetree/bindings/net/airoha,an8855-phy.yaml
 F:	Documentation/devicetree/bindings/net/dsa/airoha,an8855-switch.yaml
-- 
2.48.1

[net-next PATCH v13 06/14] net: mdio: regmap: prepare support for multiple valid addr

[Christian Marangi]

Rework the valid_addr and convert it to a mask in preparation for mdio
regmap to support multiple valid addr in the case the regmap can support
it.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
---
 drivers/net/mdio/mdio-regmap.c | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)

diff --git a/drivers/net/mdio/mdio-regmap.c b/drivers/net/mdio/mdio-regmap.c
index 8a742a8d6387..810ba0a736f0 100644
--- a/drivers/net/mdio/mdio-regmap.c
+++ b/drivers/net/mdio/mdio-regmap.c
@@ -19,7 +19,7 @@
 
 struct mdio_regmap_priv {
 	struct regmap *regmap;
-	u8 valid_addr;
+	u32 valid_addr_mask;
 };
 
 static int mdio_regmap_read_c22(struct mii_bus *bus, int addr, int regnum)
@@ -28,7 +28,7 @@ static int mdio_regmap_read_c22(struct mii_bus *bus, int addr, int regnum)
 	unsigned int val;
 	int ret;
 
-	if (ctx->valid_addr != addr)
+	if (!(ctx->valid_addr_mask & BIT(addr)))
 		return -ENODEV;
 
 	ret = regmap_read(ctx->regmap, regnum, &val);
@@ -43,7 +43,7 @@ static int mdio_regmap_write_c22(struct mii_bus *bus, int addr, int regnum,
 {
 	struct mdio_regmap_priv *ctx = bus->priv;
 
-	if (ctx->valid_addr != addr)
+	if (!(ctx->valid_addr_mask & BIT(addr)))
 		return -ENODEV;
 
 	return regmap_write(ctx->regmap, regnum, val);
@@ -65,7 +65,7 @@ struct mii_bus *devm_mdio_regmap_register(struct device *dev,
 
 	mr = mii->priv;
 	mr->regmap = config->regmap;
-	mr->valid_addr = config->valid_addr;
+	mr->valid_addr_mask = BIT(config->valid_addr);
 
 	mii->name = DRV_NAME;
 	strscpy(mii->id, config->name, MII_BUS_ID_SIZE);
@@ -74,7 +74,7 @@ struct mii_bus *devm_mdio_regmap_register(struct device *dev,
 	mii->write = mdio_regmap_write_c22;
 
 	if (config->autoscan)
-		mii->phy_mask = ~BIT(config->valid_addr);
+		mii->phy_mask = ~mr->valid_addr_mask;
 	else
 		mii->phy_mask = ~0;
 
-- 
2.48.1

[net-next PATCH v13 07/14] net: mdio: regmap: add support for C45 read/write

[Christian Marangi]

Add support for C45 read/write for mdio regmap. This can be done
by enabling the support_encoded_addr bool in mdio regmap config and by
using the new API devm_mdio_regmap_init to init a regmap.

To support C45, additional info needs to be appended to the regmap
address passed to regmap OPs.

The logic applied to the regmap address value:
- First the regnum value (20, 16)
- Second the devnum value (25, 21)
- A bit to signal if it's C45 (26)

devm_mdio_regmap_init MUST be used to register a regmap for this to
correctly handle internally the encode/decode of the address.

Drivers needs to define a mdio_regmap_init_config where an optional regmap
name can be defined and MUST define C22 OPs (mdio_read/write).
To support C45 operation also C45 OPs (mdio_read/write_c45).

The regmap from devm_mdio_regmap_init will internally decode the encoded
regmap address and extract the various info (addr, devnum if C45 and
regnum). It will then call the related OP and pass the extracted values to
the function.

Example for a C45 read operation:
- With an encoded address with C45 bit enabled, it will call the
  .mdio_read_c45 and addr, devnum and regnum will be passed.
  .mdio_read_c45 will then return the val and val will be stored in the
  regmap_read pointer and will return 0. If .mdio_read_c45 returns
  any error, then the regmap_read will return such error.

With support_encoded_addr enabled, also C22 will encode the address in
the regmap address and .mdio_read/write will called accordingly similar
to C45 operation.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
---
 drivers/net/mdio/mdio-regmap.c   | 170 +++++++++++++++++++++++++++++--
 include/linux/mdio/mdio-regmap.h |  14 +++
 2 files changed, 176 insertions(+), 8 deletions(-)

diff --git a/drivers/net/mdio/mdio-regmap.c b/drivers/net/mdio/mdio-regmap.c
index 810ba0a736f0..f263e4ae2477 100644
--- a/drivers/net/mdio/mdio-regmap.c
+++ b/drivers/net/mdio/mdio-regmap.c
@@ -15,22 +15,72 @@
 #include <linux/regmap.h>
 #include <linux/mdio/mdio-regmap.h>
 
+#define MDIO_REGMAP_C45			BIT(26)
+#define MDIO_REGMAP_ADDR		GENMASK(25, 21)
+#define MDIO_REGMAP_DEVNUM		GENMASK(20, 16)
+#define MDIO_REGMAP_REGNUM		GENMASK(15, 0)
+
 #define DRV_NAME "mdio-regmap"
 
 struct mdio_regmap_priv {
+	void *ctx;
+
+	const struct mdio_regmap_init_config *config;
+};
+
+struct mdio_regmap_mii_priv {
 	struct regmap *regmap;
 	u32 valid_addr_mask;
+	bool encode_addr;
 };
 
-static int mdio_regmap_read_c22(struct mii_bus *bus, int addr, int regnum)
+static int mdio_regmap_mii_read_c22(struct mii_bus *bus, int addr, int regnum)
+{
+	struct mdio_regmap_mii_priv *ctx = bus->priv;
+	unsigned int val;
+	int ret;
+
+	if (!(ctx->valid_addr_mask & BIT(addr)))
+		return -ENODEV;
+
+	if (ctx->encode_addr)
+		regnum |= FIELD_PREP(MDIO_REGMAP_ADDR, addr);
+
+	ret = regmap_read(ctx->regmap, regnum, &val);
+	if (ret < 0)
+		return ret;
+
+	return val;
+}
+
+static int mdio_regmap_mii_write_c22(struct mii_bus *bus, int addr, int regnum,
+				     u16 val)
 {
-	struct mdio_regmap_priv *ctx = bus->priv;
+	struct mdio_regmap_mii_priv *ctx = bus->priv;
+
+	if (!(ctx->valid_addr_mask & BIT(addr)))
+		return -ENODEV;
+
+	if (ctx->encode_addr)
+		regnum |= FIELD_PREP(MDIO_REGMAP_ADDR, addr);
+
+	return regmap_write(ctx->regmap, regnum, val);
+}
+
+static int mdio_regmap_mii_read_c45(struct mii_bus *bus, int addr, int devnum,
+				    int regnum)
+{
+	struct mdio_regmap_mii_priv *ctx = bus->priv;
 	unsigned int val;
 	int ret;
 
 	if (!(ctx->valid_addr_mask & BIT(addr)))
 		return -ENODEV;
 
+	regnum |= MDIO_REGMAP_C45;
+	regnum |= FIELD_PREP(MDIO_REGMAP_ADDR, addr);
+	regnum |= FIELD_PREP(MDIO_REGMAP_DEVNUM, devnum);
+
 	ret = regmap_read(ctx->regmap, regnum, &val);
 	if (ret < 0)
 		return ret;
@@ -38,21 +88,25 @@ static int mdio_regmap_read_c22(struct mii_bus *bus, int addr, int regnum)
 	return val;
 }
 
-static int mdio_regmap_write_c22(struct mii_bus *bus, int addr, int regnum,
-				 u16 val)
+static int mdio_regmap_mii_write_c45(struct mii_bus *bus, int addr, int devnum,
+				     int regnum, u16 val)
 {
-	struct mdio_regmap_priv *ctx = bus->priv;
+	struct mdio_regmap_mii_priv *ctx = bus->priv;
 
 	if (!(ctx->valid_addr_mask & BIT(addr)))
 		return -ENODEV;
 
+	regnum |= MDIO_REGMAP_C45;
+	regnum |= FIELD_PREP(MDIO_REGMAP_ADDR, addr);
+	regnum |= FIELD_PREP(MDIO_REGMAP_DEVNUM, devnum);
+
 	return regmap_write(ctx->regmap, regnum, val);
 }
 
 struct mii_bus *devm_mdio_regmap_register(struct device *dev,
 					  const struct mdio_regmap_config *config)
 {
-	struct mdio_regmap_priv *mr;
+	struct mdio_regmap_mii_priv *mr;
 	struct mii_bus *mii;
 	int rc;
 
@@ -66,12 +120,17 @@ struct mii_bus *devm_mdio_regmap_register(struct device *dev,
 	mr = mii->priv;
 	mr->regmap = config->regmap;
 	mr->valid_addr_mask = BIT(config->valid_addr);
+	mr->encode_addr = config->support_encoded_addr;
 
 	mii->name = DRV_NAME;
 	strscpy(mii->id, config->name, MII_BUS_ID_SIZE);
 	mii->parent = config->parent;
-	mii->read = mdio_regmap_read_c22;
-	mii->write = mdio_regmap_write_c22;
+	mii->read = mdio_regmap_mii_read_c22;
+	mii->write = mdio_regmap_mii_write_c22;
+	if (config->support_encoded_addr) {
+		mii->read_c45 = mdio_regmap_mii_read_c45;
+		mii->write_c45 = mdio_regmap_mii_write_c45;
+	}
 
 	if (config->autoscan)
 		mii->phy_mask = ~mr->valid_addr_mask;
@@ -88,6 +147,101 @@ struct mii_bus *devm_mdio_regmap_register(struct device *dev,
 }
 EXPORT_SYMBOL_GPL(devm_mdio_regmap_register);
 
+static int mdio_regmap_reg_read(void *context, unsigned int reg, unsigned int *val)
+{
+	const struct mdio_regmap_init_config *config;
+	struct mdio_regmap_priv *priv = context;
+	int addr, regnum;
+	int ret;
+
+	config = priv->config;
+
+	addr = FIELD_GET(MDIO_REGMAP_ADDR, reg);
+	regnum = FIELD_GET(MDIO_REGMAP_REGNUM, reg);
+
+	if (reg & MDIO_REGMAP_C45) {
+		int devnum;
+
+		if (!config->mdio_write_c45)
+			return -EOPNOTSUPP;
+
+		devnum = FIELD_GET(MDIO_REGMAP_DEVNUM, reg);
+		ret = config->mdio_read_c45(priv->ctx, addr, devnum, regnum);
+	} else {
+		ret = config->mdio_read(priv->ctx, addr, regnum);
+	}
+
+	if (ret < 0)
+		return ret;
+
+	*val = ret;
+	return 0;
+}
+
+static int mdio_regmap_reg_write(void *context, unsigned int reg, unsigned int val)
+{
+	const struct mdio_regmap_init_config *config;
+	struct mdio_regmap_priv *priv = context;
+	int addr, regnum;
+
+	config = priv->config;
+
+	addr = FIELD_GET(MDIO_REGMAP_ADDR, reg);
+	regnum = FIELD_GET(MDIO_REGMAP_REGNUM, reg);
+
+	if (reg & MDIO_REGMAP_C45) {
+		int devnum;
+
+		if (!config->mdio_write_c45)
+			return -EOPNOTSUPP;
+
+		devnum = FIELD_GET(MDIO_REGMAP_DEVNUM, reg);
+		return config->mdio_write_c45(priv->ctx, addr, devnum, regnum, val);
+	}
+
+	return config->mdio_write(priv->ctx, addr, regnum, val);
+}
+
+static const struct regmap_config mdio_regmap_default_config = {
+	.reg_bits = 26,
+	.val_bits = 16,
+	.reg_stride = 1,
+	.max_register = MDIO_REGMAP_C45 | MDIO_REGMAP_ADDR |
+			MDIO_REGMAP_DEVNUM | MDIO_REGMAP_REGNUM,
+	.reg_read = mdio_regmap_reg_read,
+	.reg_write = mdio_regmap_reg_write,
+	/* Locking MUST be handled in mdio_write/read(_c45) */
+	.disable_locking = true,
+};
+
+struct regmap *devm_mdio_regmap_init(struct device *dev, void *priv,
+				     const struct mdio_regmap_init_config *config)
+{
+	struct mdio_regmap_priv *mdio_regmap_priv;
+	struct regmap_config regmap_config;
+
+	/* Validate config */
+	if (!config->mdio_read || !config->mdio_write) {
+		dev_err(dev, ".mdio_read and .mdio_write MUST be defined in config\n");
+		return ERR_PTR(-EINVAL);
+	}
+
+	mdio_regmap_priv = devm_kzalloc(dev, sizeof(*mdio_regmap_priv),
+					GFP_KERNEL);
+	if (!mdio_regmap_priv)
+		return ERR_PTR(-ENOMEM);
+
+	memcpy(&regmap_config, &mdio_regmap_default_config, sizeof(regmap_config));
+	regmap_config.name = config->name;
+
+	mdio_regmap_priv->ctx = priv;
+	mdio_regmap_priv->config = config;
+
+	return devm_regmap_init(dev, NULL, mdio_regmap_priv,
+				&regmap_config);
+}
+EXPORT_SYMBOL_GPL(devm_mdio_regmap_init);
+
 MODULE_DESCRIPTION("MDIO API over regmap");
 MODULE_AUTHOR("Maxime Chevallier <maxime.chevallier@bootlin.com>");
 MODULE_LICENSE("GPL");
diff --git a/include/linux/mdio/mdio-regmap.h b/include/linux/mdio/mdio-regmap.h
index 679d9069846b..504fa2046043 100644
--- a/include/linux/mdio/mdio-regmap.h
+++ b/include/linux/mdio/mdio-regmap.h
@@ -17,10 +17,24 @@ struct mdio_regmap_config {
 	struct regmap *regmap;
 	char name[MII_BUS_ID_SIZE];
 	u8 valid_addr;
+	/* devm_mdio_regmap_init is required with this enabled */
+	bool support_encoded_addr;
 	bool autoscan;
 };
 
 struct mii_bus *devm_mdio_regmap_register(struct device *dev,
 					  const struct mdio_regmap_config *config);
 
+struct mdio_regmap_init_config {
+	const char *name;
+
+	int (*mdio_read)(void *ctx, int addr, int regnum);
+	int (*mdio_write)(void *ctx, int addr, int regnum, u16 val);
+	int (*mdio_read_c45)(void *ctx, int addr, int devnum, int regnum);
+	int (*mdio_write_c45)(void *ctx, int addr, int devnum, int regnum, u16 val);
+};
+
+struct regmap *devm_mdio_regmap_init(struct device *dev, void *priv,
+				     const struct mdio_regmap_init_config *config);
+
 #endif
-- 
2.48.1

[net-next PATCH v13 08/14] net: mdio: regmap: add support for multiple valid addr

[Christian Marangi]

Add support for multiple valid addr for mdio regmap. This can be done by
defining the new valid_addr_mask value in the mdio regmap config.

This makes use of the new implementation used by C45 to encode
additional info in the regmap address to support multiple MDIO address.

To actually use this, support_encoded_addr MUST be enabled and
(indirectly) devm_mdio_regmap_init must be used to create the regmap.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
---
 drivers/net/mdio/mdio-regmap.c   | 8 +++++++-
 include/linux/mdio/mdio-regmap.h | 1 +
 2 files changed, 8 insertions(+), 1 deletion(-)

diff --git a/drivers/net/mdio/mdio-regmap.c b/drivers/net/mdio/mdio-regmap.c
index f263e4ae2477..ed0443eb039f 100644
--- a/drivers/net/mdio/mdio-regmap.c
+++ b/drivers/net/mdio/mdio-regmap.c
@@ -113,13 +113,19 @@ struct mii_bus *devm_mdio_regmap_register(struct device *dev,
 	if (!config->parent)
 		return ERR_PTR(-EINVAL);
 
+	if (config->valid_addr_mask && !config->support_encoded_addr) {
+		dev_err(dev, "encoded address support is required to support multiple MDIO address\n");
+		return ERR_PTR(-EINVAL);
+	}
+
 	mii = devm_mdiobus_alloc_size(config->parent, sizeof(*mr));
 	if (!mii)
 		return ERR_PTR(-ENOMEM);
 
 	mr = mii->priv;
 	mr->regmap = config->regmap;
-	mr->valid_addr_mask = BIT(config->valid_addr);
+	mr->valid_addr_mask = config->valid_addr_mask ? config->valid_addr_mask :
+							BIT(config->valid_addr);
 	mr->encode_addr = config->support_encoded_addr;
 
 	mii->name = DRV_NAME;
diff --git a/include/linux/mdio/mdio-regmap.h b/include/linux/mdio/mdio-regmap.h
index 504fa2046043..bb0e7dc9c0dc 100644
--- a/include/linux/mdio/mdio-regmap.h
+++ b/include/linux/mdio/mdio-regmap.h
@@ -17,6 +17,7 @@ struct mdio_regmap_config {
 	struct regmap *regmap;
 	char name[MII_BUS_ID_SIZE];
 	u8 valid_addr;
+	u32 valid_addr_mask;
 	/* devm_mdio_regmap_init is required with this enabled */
 	bool support_encoded_addr;
 	bool autoscan;
-- 
2.48.1

[net-next PATCH v13 09/14] net: mdio: regmap: add OF support

[Christian Marangi]

Permit to pass a device tree node to mdio regmap config and use
the OF variant of mdiobus_register.

This is done to autoprobe PHY defined in device tree as the current
mdiobus_register only permits probing PHY using the MDIO mask value.

Previous implementation is not changed as of_mdiobus_register fallback
to mdiobus_register if the passed device tree pointer is NULL.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
---
 drivers/net/mdio/mdio-regmap.c   | 2 +-
 include/linux/mdio/mdio-regmap.h | 1 +
 2 files changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/net/mdio/mdio-regmap.c b/drivers/net/mdio/mdio-regmap.c
index ed0443eb039f..8e89068c844d 100644
--- a/drivers/net/mdio/mdio-regmap.c
+++ b/drivers/net/mdio/mdio-regmap.c
@@ -143,7 +143,7 @@ struct mii_bus *devm_mdio_regmap_register(struct device *dev,
 	else
 		mii->phy_mask = ~0;
 
-	rc = devm_mdiobus_register(dev, mii);
+	rc = devm_of_mdiobus_register(dev, mii, config->np);
 	if (rc) {
 		dev_err(config->parent, "Cannot register MDIO bus![%s] (%d)\n", mii->id, rc);
 		return ERR_PTR(rc);
diff --git a/include/linux/mdio/mdio-regmap.h b/include/linux/mdio/mdio-regmap.h
index bb0e7dc9c0dc..228f12e90750 100644
--- a/include/linux/mdio/mdio-regmap.h
+++ b/include/linux/mdio/mdio-regmap.h
@@ -14,6 +14,7 @@ struct regmap;
 
 struct mdio_regmap_config {
 	struct device *parent;
+	struct device_node *np;
 	struct regmap *regmap;
 	char name[MII_BUS_ID_SIZE];
 	u8 valid_addr;
-- 
2.48.1

[net-next PATCH v13 10/14] mfd: an8855: Add support for Airoha AN8855 Switch MFD

[Christian Marangi]

Add support for Airoha AN8855 Switch MFD that provide support for a DSA
switch and a NVMEM provider. Also provide support for a virtual MDIO
passthrough as the PHYs address for the switch are shared with the switch
address.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
---
 MAINTAINERS                 |   1 +
 drivers/mfd/Kconfig         |  12 +
 drivers/mfd/Makefile        |   1 +
 drivers/mfd/airoha-an8855.c | 429 ++++++++++++++++++++++++++++++++++++
 4 files changed, 443 insertions(+)
 create mode 100644 drivers/mfd/airoha-an8855.c

diff --git a/MAINTAINERS b/MAINTAINERS
index 65709e47adc7..aec293953382 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -730,6 +730,7 @@ F:	Documentation/devicetree/bindings/net/airoha,an8855-mdio.yaml
 F:	Documentation/devicetree/bindings/net/airoha,an8855-phy.yaml
 F:	Documentation/devicetree/bindings/net/dsa/airoha,an8855-switch.yaml
 F:	Documentation/devicetree/bindings/nvmem/airoha,an8855-efuse.yaml
+F:	drivers/mfd/airoha-an8855.c
 
 AIROHA ETHERNET DRIVER
 M:	Lorenzo Bianconi <lorenzo@kernel.org>
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index 6b0682af6e32..ebdced27e96a 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -53,6 +53,18 @@ config MFD_ALTERA_SYSMGR
 	  using regmap_mmio accesses for ARM32 parts and SMC calls to
 	  EL3 for ARM64 parts.
 
+config MFD_AIROHA_AN8855
+	tristate "Airoha AN8855 Switch Core"
+	select MFD_CORE
+	select MDIO_DEVICE
+	depends on NETDEVICES && OF
+	help
+	  Support for the Airoha AN8855 Switch Core. This is an SoC
+	  that provides various peripherals, to count, i2c, an Ethrnet
+	  Switch, a CPU timer, GPIO, eFUSE.
+
+	  Currently it provides a DSA switch and a NVMEM provider.
+
 config MFD_ACT8945A
 	tristate "Active-semi ACT8945A"
 	select MFD_CORE
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index 9220eaf7cf12..37677f65a981 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -8,6 +8,7 @@ obj-$(CONFIG_MFD_88PM860X)	+= 88pm860x.o
 obj-$(CONFIG_MFD_88PM800)	+= 88pm800.o 88pm80x.o
 obj-$(CONFIG_MFD_88PM805)	+= 88pm805.o 88pm80x.o
 obj-$(CONFIG_MFD_88PM886_PMIC)	+= 88pm886.o
+obj-$(CONFIG_MFD_AIROHA_AN8855)	+= airoha-an8855.o
 obj-$(CONFIG_MFD_ACT8945A)	+= act8945a.o
 obj-$(CONFIG_MFD_SM501)		+= sm501.o
 obj-$(CONFIG_ARCH_BCM2835)	+= bcm2835-pm.o
diff --git a/drivers/mfd/airoha-an8855.c b/drivers/mfd/airoha-an8855.c
new file mode 100644
index 000000000000..fb2edf3132f9
--- /dev/null
+++ b/drivers/mfd/airoha-an8855.c
@@ -0,0 +1,429 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Core driver for Airoha AN8855 Switch
+ */
+
+#include <linux/bitfield.h>
+#include <linux/gpio/consumer.h>
+#include <linux/mfd/core.h>
+#include <linux/mdio.h>
+#include <linux/mdio/mdio-regmap.h>
+#include <linux/module.h>
+#include <linux/phy.h>
+#include <linux/regmap.h>
+
+/* Register for HW trap status */
+#define AN8855_HWTRAP			0x1000009c
+
+#define AN8855_CREV			0x10005000
+#define   AN8855_ID			0x8855
+
+#define AN8855_RG_GPHY_AFE_PWD		0x1028c840
+
+/* MII Registers */
+#define AN8855_PHY_SELECT_PAGE		0x1f
+#define   AN8855_PHY_PAGE		GENMASK(2, 0)
+#define   AN8855_PHY_PAGE_STANDARD	FIELD_PREP_CONST(AN8855_PHY_PAGE, 0x0)
+#define   AN8855_PHY_PAGE_EXTENDED_1	FIELD_PREP_CONST(AN8855_PHY_PAGE, 0x1)
+#define   AN8855_PHY_PAGE_EXTENDED_4	FIELD_PREP_CONST(AN8855_PHY_PAGE, 0x4)
+
+/* MII Registers Page 4 */
+#define AN8855_PBUS_MODE		0x10
+#define   AN8855_PBUS_MODE_ADDR_FIXED	0x0
+#define AN8855_PBUS_MODE_ADDR_INCR	BIT(15)
+#define AN8855_PBUS_WR_ADDR_HIGH	0x11
+#define AN8855_PBUS_WR_ADDR_LOW		0x12
+#define AN8855_PBUS_WR_DATA_HIGH	0x13
+#define AN8855_PBUS_WR_DATA_LOW		0x14
+#define AN8855_PBUS_RD_ADDR_HIGH	0x15
+#define AN8855_PBUS_RD_ADDR_LOW		0x16
+#define AN8855_PBUS_RD_DATA_HIGH	0x17
+#define AN8855_PBUS_RD_DATA_LOW		0x18
+
+struct an8855_core_priv {
+	struct mii_bus *bus;
+
+	unsigned int switch_addr;
+	u16 current_page;
+};
+
+static const struct mfd_cell an8855_core_childs[] = {
+	{
+		.name = "an8855-efuse",
+		.of_compatible = "airoha,an8855-efuse",
+	}, {
+		.name = "an8855-switch",
+		.of_compatible = "airoha,an8855-switch",
+	}, {
+		.name = "an8855-mdio",
+		.of_compatible = "airoha,an8855-mdio",
+	}
+};
+
+static int an8855_mii_set_page(struct an8855_core_priv *priv, u8 addr,
+			       u8 page) __must_hold(&priv->bus->mdio_lock)
+{
+	struct mii_bus *bus = priv->bus;
+	int ret;
+
+	ret = __mdiobus_write(bus, addr, AN8855_PHY_SELECT_PAGE, page);
+	if (ret) {
+		dev_err_ratelimited(&bus->dev, "failed to set mii page\n");
+		return ret;
+	}
+
+	/* Cache current page if next MII read/write is for Switch page */
+	priv->current_page = page;
+	return 0;
+}
+
+static int an8855_mii_read32(struct mii_bus *bus, u8 phy_id, u32 reg,
+			     u32 *val) __must_hold(&bus->mdio_lock)
+{
+	int lo, hi, ret;
+
+	ret = __mdiobus_write(bus, phy_id, AN8855_PBUS_MODE,
+			      AN8855_PBUS_MODE_ADDR_FIXED);
+	if (ret)
+		goto err;
+
+	ret = __mdiobus_write(bus, phy_id, AN8855_PBUS_RD_ADDR_HIGH,
+			      upper_16_bits(reg));
+	if (ret)
+		goto err;
+
+	ret = __mdiobus_write(bus, phy_id, AN8855_PBUS_RD_ADDR_LOW,
+			      lower_16_bits(reg));
+	if (ret)
+		goto err;
+
+	hi = __mdiobus_read(bus, phy_id, AN8855_PBUS_RD_DATA_HIGH);
+	if (hi < 0) {
+		ret = hi;
+		goto err;
+	}
+
+	lo = __mdiobus_read(bus, phy_id, AN8855_PBUS_RD_DATA_LOW);
+	if (lo < 0) {
+		ret = lo;
+		goto err;
+	}
+
+	*val = ((u16)hi << 16) | ((u16)lo & 0xffff);
+
+	return 0;
+err:
+	dev_err_ratelimited(&bus->dev, "failed to read register\n");
+	return ret;
+}
+
+static int an8855_regmap_read(void *ctx, uint32_t reg, uint32_t *val)
+{
+	struct an8855_core_priv *priv = ctx;
+	struct mii_bus *bus = priv->bus;
+	u16 addr = priv->switch_addr;
+	int ret;
+
+	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
+	ret = an8855_mii_set_page(priv, addr, AN8855_PHY_PAGE_EXTENDED_4);
+	if (ret < 0)
+		goto exit;
+
+	ret = an8855_mii_read32(bus, addr, reg, val);
+
+exit:
+	mutex_unlock(&bus->mdio_lock);
+
+	return ret < 0 ? ret : 0;
+}
+
+static int an8855_mii_write32(struct mii_bus *bus, u8 phy_id, u32 reg,
+			      u32 val) __must_hold(&bus->mdio_lock)
+{
+	int ret;
+
+	ret = __mdiobus_write(bus, phy_id, AN8855_PBUS_MODE,
+			      AN8855_PBUS_MODE_ADDR_FIXED);
+	if (ret)
+		goto err;
+
+	ret = __mdiobus_write(bus, phy_id, AN8855_PBUS_WR_ADDR_HIGH,
+			      upper_16_bits(reg));
+	if (ret)
+		goto err;
+	ret = __mdiobus_write(bus, phy_id, AN8855_PBUS_WR_ADDR_LOW,
+			      lower_16_bits(reg));
+	if (ret)
+		goto err;
+
+	ret = __mdiobus_write(bus, phy_id, AN8855_PBUS_WR_DATA_HIGH,
+			      upper_16_bits(val));
+	if (ret)
+		goto err;
+
+	ret = __mdiobus_write(bus, phy_id, AN8855_PBUS_WR_DATA_LOW,
+			      lower_16_bits(val));
+	if (ret)
+		goto err;
+
+	return 0;
+err:
+	dev_err_ratelimited(&bus->dev,
+			    "failed to write an8855 register\n");
+	return ret;
+}
+
+static int an8855_regmap_write(void *ctx, uint32_t reg, uint32_t val)
+{
+	struct an8855_core_priv *priv = ctx;
+	struct mii_bus *bus = priv->bus;
+	u16 addr = priv->switch_addr;
+	int ret;
+
+	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
+	ret = an8855_mii_set_page(priv, addr, AN8855_PHY_PAGE_EXTENDED_4);
+	if (ret)
+		goto exit;
+
+	ret = an8855_mii_write32(bus, addr, reg, val);
+
+exit:
+	mutex_unlock(&bus->mdio_lock);
+
+	return ret < 0 ? ret : 0;
+}
+
+static int an8855_regmap_update_bits(void *ctx, uint32_t reg, uint32_t mask,
+				     uint32_t write_val)
+{
+	struct an8855_core_priv *priv = ctx;
+	struct mii_bus *bus = priv->bus;
+	u16 addr = priv->switch_addr;
+	u32 val;
+	int ret;
+
+	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
+	ret = an8855_mii_set_page(priv, addr, AN8855_PHY_PAGE_EXTENDED_4);
+	if (ret)
+		goto exit;
+
+	ret = an8855_mii_read32(bus, addr, reg, &val);
+	if (ret < 0)
+		goto exit;
+
+	val &= ~mask;
+	val |= write_val;
+	ret = an8855_mii_write32(bus, addr, reg, val);
+
+exit:
+	mutex_unlock(&bus->mdio_lock);
+
+	return ret < 0 ? ret : 0;
+}
+
+static const struct regmap_range an8855_readable_ranges[] = {
+	regmap_reg_range(0x10000000, 0x10000fff), /* SCU */
+	regmap_reg_range(0x10001000, 0x10001fff), /* RBUS */
+	regmap_reg_range(0x10002000, 0x10002fff), /* MCU */
+	regmap_reg_range(0x10005000, 0x10005fff), /* SYS SCU */
+	regmap_reg_range(0x10007000, 0x10007fff), /* I2C Slave */
+	regmap_reg_range(0x10008000, 0x10008fff), /* I2C Master */
+	regmap_reg_range(0x10009000, 0x10009fff), /* PDMA */
+	regmap_reg_range(0x1000a100, 0x1000a2ff), /* General Purpose Timer */
+	regmap_reg_range(0x1000a200, 0x1000a2ff), /* GPU timer */
+	regmap_reg_range(0x1000a300, 0x1000a3ff), /* GPIO */
+	regmap_reg_range(0x1000a400, 0x1000a5ff), /* EFUSE */
+	regmap_reg_range(0x1000c000, 0x1000cfff), /* GDMP CSR */
+	regmap_reg_range(0x10010000, 0x1001ffff), /* GDMP SRAM */
+	regmap_reg_range(0x10200000, 0x10203fff), /* Switch - ARL Global */
+	regmap_reg_range(0x10204000, 0x10207fff), /* Switch - BMU */
+	regmap_reg_range(0x10208000, 0x1020bfff), /* Switch - ARL Port */
+	regmap_reg_range(0x1020c000, 0x1020cfff), /* Switch - SCH */
+	regmap_reg_range(0x10210000, 0x10213fff), /* Switch - MAC */
+	regmap_reg_range(0x10214000, 0x10217fff), /* Switch - MIB */
+	regmap_reg_range(0x10218000, 0x1021bfff), /* Switch - Port Control */
+	regmap_reg_range(0x1021c000, 0x1021ffff), /* Switch - TOP */
+	regmap_reg_range(0x10220000, 0x1022ffff), /* SerDes */
+	regmap_reg_range(0x10286000, 0x10286fff), /* RG Batcher */
+	regmap_reg_range(0x1028c000, 0x1028ffff), /* ETHER_SYS */
+	regmap_reg_range(0x30000000, 0x37ffffff), /* I2C EEPROM */
+	regmap_reg_range(0x38000000, 0x3fffffff), /* BOOT_ROM */
+	regmap_reg_range(0xa0000000, 0xbfffffff), /* GPHY */
+};
+
+static const struct regmap_access_table an8855_readable_table = {
+	.yes_ranges = an8855_readable_ranges,
+	.n_yes_ranges = ARRAY_SIZE(an8855_readable_ranges),
+};
+
+static const struct regmap_config an8855_regmap_config = {
+	.name = "switch",
+	.reg_bits = 32,
+	.val_bits = 32,
+	.reg_stride = 4,
+	.max_register = 0xbfffffff,
+	.reg_read = an8855_regmap_read,
+	.reg_write = an8855_regmap_write,
+	.reg_update_bits = an8855_regmap_update_bits,
+	.disable_locking = true,
+	.rd_table = &an8855_readable_table,
+};
+
+static int an855_regmap_phy_reset_page(struct an8855_core_priv *priv,
+				       int phy) __must_hold(&priv->bus->mdio_lock)
+{
+	/* Check PHY page only for addr shared with switch */
+	if (phy != priv->switch_addr)
+		return 0;
+
+	/* Don't restore page if it's not set to Switch page */
+	if (priv->current_page != FIELD_GET(AN8855_PHY_PAGE,
+					    AN8855_PHY_PAGE_EXTENDED_4))
+		return 0;
+
+	/*
+	 * Restore page to 0, PHY might change page right after but that
+	 * will be ignored as it won't be a switch page.
+	 */
+	return an8855_mii_set_page(priv, phy, AN8855_PHY_PAGE_STANDARD);
+}
+
+static int an8855_regmap_phy_read(void *ctx, int addr, int regnum)
+{
+	struct an8855_core_priv *priv = ctx;
+	struct mii_bus *bus = priv->bus;
+	int ret;
+
+	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
+	ret = an855_regmap_phy_reset_page(priv, addr);
+	if (ret)
+		goto exit;
+
+	ret = __mdiobus_read(priv->bus, addr, regnum);
+
+exit:
+	mutex_unlock(&bus->mdio_lock);
+
+	return ret;
+}
+
+static int an8855_regmap_phy_write(void *ctx, int addr, int regnum, u16 val)
+{
+	struct an8855_core_priv *priv = ctx;
+	struct mii_bus *bus = priv->bus;
+	int ret;
+
+	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
+	ret = an855_regmap_phy_reset_page(priv, addr);
+	if (ret)
+		goto exit;
+
+	ret = __mdiobus_write(priv->bus, addr, regnum, val);
+
+exit:
+	mutex_unlock(&bus->mdio_lock);
+
+	return ret;
+}
+
+static const struct mdio_regmap_init_config an8855_regmap_phy_config = {
+	.name = "phy",
+	.mdio_read = an8855_regmap_phy_read,
+	.mdio_write = an8855_regmap_phy_write,
+};
+
+static int an8855_read_switch_id(struct device *dev, struct regmap *regmap)
+{
+	u32 id;
+	int ret;
+
+	ret = regmap_read(regmap, AN8855_CREV, &id);
+	if (ret)
+		return ret;
+
+	if (id != AN8855_ID) {
+		dev_err(dev, "Detected Switch ID %x but %x was expected\n",
+			id, AN8855_ID);
+		return -ENODEV;
+	}
+
+	return 0;
+}
+
+static int an8855_core_probe(struct mdio_device *mdiodev)
+{
+	struct regmap *regmap, *regmap_phy;
+	struct device *dev = &mdiodev->dev;
+	struct an8855_core_priv *priv;
+	struct gpio_desc *reset_gpio;
+	u32 val;
+	int ret;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->bus = mdiodev->bus;
+	priv->switch_addr = mdiodev->addr;
+	/* No DMA for mdiobus, mute warning for DMA mask not set */
+	dev->dma_mask = &dev->coherent_dma_mask;
+
+	regmap = devm_regmap_init(dev, NULL, priv, &an8855_regmap_config);
+	if (IS_ERR(regmap))
+		return dev_err_probe(dev, PTR_ERR(regmap),
+				     "regmap initialization failed\n");
+
+	regmap_phy = devm_mdio_regmap_init(dev, priv, &an8855_regmap_phy_config);
+	if (IS_ERR(regmap_phy))
+		return dev_err_probe(dev, PTR_ERR(regmap_phy),
+				     "regmap phy initialization failed\n");
+
+	reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
+	if (IS_ERR(reset_gpio))
+		return PTR_ERR(reset_gpio);
+
+	if (reset_gpio) {
+		usleep_range(100000, 150000);
+		gpiod_set_value_cansleep(reset_gpio, 0);
+		usleep_range(100000, 150000);
+		gpiod_set_value_cansleep(reset_gpio, 1);
+
+		/* Poll HWTRAP reg to wait for Switch to fully Init */
+		ret = regmap_read_poll_timeout(regmap, AN8855_HWTRAP, val,
+					       val, 20, 200000);
+		if (ret)
+			return ret;
+	}
+
+	ret = an8855_read_switch_id(dev, regmap);
+	if (ret)
+		return ret;
+
+	/* Release global PHY power down */
+	ret = regmap_write(regmap, AN8855_RG_GPHY_AFE_PWD, 0x0);
+	if (ret)
+		return ret;
+
+	return devm_mfd_add_devices(dev, PLATFORM_DEVID_AUTO, an8855_core_childs,
+				    ARRAY_SIZE(an8855_core_childs), NULL, 0,
+				    NULL);
+}
+
+static const struct of_device_id an8855_core_of_match[] = {
+	{ .compatible = "airoha,an8855" },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, an8855_core_of_match);
+
+static struct mdio_driver an8855_core_driver = {
+	.probe = an8855_core_probe,
+	.mdiodrv.driver = {
+		.name = "an8855",
+		.of_match_table = an8855_core_of_match,
+	},
+};
+mdio_module_driver(an8855_core_driver);
+
+MODULE_AUTHOR("Christian Marangi <ansuelsmth@gmail.com>");
+MODULE_DESCRIPTION("Driver for Airoha AN8855 MFD");
+MODULE_LICENSE("GPL");
-- 
2.48.1

[net-next PATCH v13 11/14] net: mdio: Add Airoha AN8855 Switch MDIO Passtrough

[Christian Marangi]

Add Airoha AN8855 Switch driver to register a MDIO passtrough as switch
address is shared with the internal PHYs and require additional page
handling.

This requires the upper Switch MFD to be probed and init to actually
work.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
---
 MAINTAINERS                    |  1 +
 drivers/net/mdio/Kconfig       | 10 +++++++
 drivers/net/mdio/Makefile      |  1 +
 drivers/net/mdio/mdio-an8855.c | 49 ++++++++++++++++++++++++++++++++++
 4 files changed, 61 insertions(+)
 create mode 100644 drivers/net/mdio/mdio-an8855.c

diff --git a/MAINTAINERS b/MAINTAINERS
index aec293953382..f4c8054d3980 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -731,6 +731,7 @@ F:	Documentation/devicetree/bindings/net/airoha,an8855-phy.yaml
 F:	Documentation/devicetree/bindings/net/dsa/airoha,an8855-switch.yaml
 F:	Documentation/devicetree/bindings/nvmem/airoha,an8855-efuse.yaml
 F:	drivers/mfd/airoha-an8855.c
+F:	drivers/net/mdio/mdio-an8855.c
 
 AIROHA ETHERNET DRIVER
 M:	Lorenzo Bianconi <lorenzo@kernel.org>
diff --git a/drivers/net/mdio/Kconfig b/drivers/net/mdio/Kconfig
index 4a7a303be2f7..e31a37064934 100644
--- a/drivers/net/mdio/Kconfig
+++ b/drivers/net/mdio/Kconfig
@@ -61,6 +61,16 @@ config MDIO_XGENE
 	  This module provides a driver for the MDIO busses found in the
 	  APM X-Gene SoC's.
 
+config MDIO_AN8855
+	tristate "Airoha AN8855 Switch MDIO bus controller"
+	depends on MFD_AIROHA_AN8855
+	depends on OF_MDIO
+	select MDIO_REGMAP
+	help
+	  This module provides a driver for the Airoha AN8855 Switch
+	  that requires a MDIO passtrough as switch address is shared
+	  with the internal PHYs and requires additional page handling.
+
 config MDIO_ASPEED
 	tristate "ASPEED MDIO bus controller"
 	depends on ARCH_ASPEED || COMPILE_TEST
diff --git a/drivers/net/mdio/Makefile b/drivers/net/mdio/Makefile
index 1015f0db4531..546c4e55b475 100644
--- a/drivers/net/mdio/Makefile
+++ b/drivers/net/mdio/Makefile
@@ -5,6 +5,7 @@ obj-$(CONFIG_ACPI_MDIO)		+= acpi_mdio.o
 obj-$(CONFIG_FWNODE_MDIO)	+= fwnode_mdio.o
 obj-$(CONFIG_OF_MDIO)		+= of_mdio.o
 
+obj-$(CONFIG_MDIO_AN8855)		+= mdio-an8855.o
 obj-$(CONFIG_MDIO_ASPEED)		+= mdio-aspeed.o
 obj-$(CONFIG_MDIO_BCM_IPROC)		+= mdio-bcm-iproc.o
 obj-$(CONFIG_MDIO_BCM_UNIMAC)		+= mdio-bcm-unimac.o
diff --git a/drivers/net/mdio/mdio-an8855.c b/drivers/net/mdio/mdio-an8855.c
new file mode 100644
index 000000000000..22d199942f1c
--- /dev/null
+++ b/drivers/net/mdio/mdio-an8855.c
@@ -0,0 +1,49 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * MDIO passthrough driver for Airoha AN8855 Switch
+ */
+
+#include <linux/mdio/mdio-regmap.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+static int an8855_mdio_probe(struct platform_device *pdev)
+{
+	struct mdio_regmap_config mrc = { };
+	struct device *dev = &pdev->dev;
+	struct mii_bus *bus;
+
+	mrc.regmap = dev_get_regmap(dev->parent, "phy");
+	mrc.parent = dev;
+	mrc.valid_addr_mask = GENMASK(31, 0);
+	mrc.support_encoded_addr = true;
+	mrc.autoscan = true;
+	mrc.np = dev->of_node;
+	snprintf(mrc.name, MII_BUS_ID_SIZE, KBUILD_MODNAME);
+
+	bus = devm_mdio_regmap_register(dev, &mrc);
+	if (IS_ERR(bus))
+		return dev_err_probe(dev, PTR_ERR(bus), "failed to register MDIO bus\n");
+
+	return 0;
+}
+
+static const struct of_device_id an8855_mdio_of_match[] = {
+	{ .compatible = "airoha,an8855-mdio", },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, an8855_mdio_of_match);
+
+static struct platform_driver an8855_mdio_driver = {
+	.probe	= an8855_mdio_probe,
+	.driver = {
+		.name = "an8855-mdio",
+		.of_match_table = an8855_mdio_of_match,
+	},
+};
+module_platform_driver(an8855_mdio_driver);
+
+MODULE_AUTHOR("Christian Marangi <ansuelsmth@gmail.com>");
+MODULE_DESCRIPTION("Driver for AN8855 MDIO passthrough");
+MODULE_LICENSE("GPL");
-- 
2.48.1

[net-next PATCH v13 12/14] nvmem: an8855: Add support for Airoha AN8855 Switch EFUSE

[Christian Marangi]

Add support for Airoha AN8855 Switch EFUSE. These EFUSE might be used
for calibration data for the internal switch PHYs.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
---
 MAINTAINERS                  |  1 +
 drivers/nvmem/Kconfig        | 11 +++++++
 drivers/nvmem/Makefile       |  2 ++
 drivers/nvmem/an8855-efuse.c | 63 ++++++++++++++++++++++++++++++++++++
 4 files changed, 77 insertions(+)
 create mode 100644 drivers/nvmem/an8855-efuse.c

diff --git a/MAINTAINERS b/MAINTAINERS
index f4c8054d3980..2cc8871186d5 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -732,6 +732,7 @@ F:	Documentation/devicetree/bindings/net/dsa/airoha,an8855-switch.yaml
 F:	Documentation/devicetree/bindings/nvmem/airoha,an8855-efuse.yaml
 F:	drivers/mfd/airoha-an8855.c
 F:	drivers/net/mdio/mdio-an8855.c
+F:	drivers/nvmem/an8855-efuse.c
 
 AIROHA ETHERNET DRIVER
 M:	Lorenzo Bianconi <lorenzo@kernel.org>
diff --git a/drivers/nvmem/Kconfig b/drivers/nvmem/Kconfig
index 8671b7c974b9..ca96c6ea685a 100644
--- a/drivers/nvmem/Kconfig
+++ b/drivers/nvmem/Kconfig
@@ -28,6 +28,17 @@ source "drivers/nvmem/layouts/Kconfig"
 
 # Devices
 
+config NVMEM_AN8855_EFUSE
+	tristate "Airoha AN8855 eFuse support"
+	depends on MFD_AIROHA_AN8855 || COMPILE_TEST
+	help
+	  Say y here to enable support for reading eFuses on Airoha AN8855
+	  Switch. These are e.g. used to store factory programmed
+	  calibration data required for the PHY.
+
+	  This driver can also be built as a module. If so, the module will
+	  be called nvmem-an8855-efuse.
+
 config NVMEM_APPLE_EFUSES
 	tristate "Apple eFuse support"
 	depends on ARCH_APPLE || COMPILE_TEST
diff --git a/drivers/nvmem/Makefile b/drivers/nvmem/Makefile
index 5b77bbb6488b..c732132c0e45 100644
--- a/drivers/nvmem/Makefile
+++ b/drivers/nvmem/Makefile
@@ -10,6 +10,8 @@ nvmem_layouts-y			:= layouts.o
 obj-y				+= layouts/
 
 # Devices
+obj-$(CONFIG_NVMEM_AN8855_EFUSE)	+= nvmem-an8855-efuse.o
+nvmem-an8855-efuse-y 			:= an8855-efuse.o
 obj-$(CONFIG_NVMEM_APPLE_EFUSES)	+= nvmem-apple-efuses.o
 nvmem-apple-efuses-y 			:= apple-efuses.o
 obj-$(CONFIG_NVMEM_BCM_OCOTP)		+= nvmem-bcm-ocotp.o
diff --git a/drivers/nvmem/an8855-efuse.c b/drivers/nvmem/an8855-efuse.c
new file mode 100644
index 000000000000..cd1564379098
--- /dev/null
+++ b/drivers/nvmem/an8855-efuse.c
@@ -0,0 +1,63 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ *  Airoha AN8855 Switch EFUSE Driver
+ */
+
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
+#include <linux/nvmem-provider.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#define AN8855_EFUSE_CELL		50
+
+#define AN8855_EFUSE_DATA0		0x1000a500
+#define   AN8855_EFUSE_R50O		GENMASK(30, 24)
+
+static int an8855_efuse_read(void *context, unsigned int offset,
+			     void *val, size_t bytes)
+{
+	struct regmap *regmap = context;
+
+	return regmap_bulk_read(regmap, AN8855_EFUSE_DATA0 + offset,
+				val, bytes / sizeof(u32));
+}
+
+static int an8855_efuse_probe(struct platform_device *pdev)
+{
+	struct nvmem_config an8855_nvmem_config = {
+		.name = "an8855-efuse",
+		.size = AN8855_EFUSE_CELL * sizeof(u32),
+		.stride = sizeof(u32),
+		.word_size = sizeof(u32),
+		.reg_read = an8855_efuse_read,
+	};
+	struct device *dev = &pdev->dev;
+	struct nvmem_device *nvmem;
+
+	/* Assign NVMEM priv to MFD regmap */
+	an8855_nvmem_config.priv = dev_get_regmap(dev->parent, "switch");
+	an8855_nvmem_config.dev = dev;
+	nvmem = devm_nvmem_register(dev, &an8855_nvmem_config);
+
+	return PTR_ERR_OR_ZERO(nvmem);
+}
+
+static const struct of_device_id an8855_efuse_of_match[] = {
+	{ .compatible = "airoha,an8855-efuse", },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, an8855_efuse_of_match);
+
+static struct platform_driver an8855_efuse_driver = {
+	.probe = an8855_efuse_probe,
+	.driver = {
+		.name = "an8855-efuse",
+		.of_match_table = an8855_efuse_of_match,
+	},
+};
+module_platform_driver(an8855_efuse_driver);
+
+MODULE_AUTHOR("Christian Marangi <ansuelsmth@gmail.com>");
+MODULE_DESCRIPTION("Driver for AN8855 Switch EFUSE");
+MODULE_LICENSE("GPL");
-- 
2.48.1

[net-next PATCH v13 14/14] net: phy: Add Airoha AN8855 Internal Switch Gigabit PHY

[Christian Marangi]

Add support for Airoha AN8855 Internal Switch Gigabit PHY.

This is a simple PHY driver to configure and calibrate the PHY for the
AN8855 Switch with the use of NVMEM cells.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
---
 MAINTAINERS                  |   1 +
 drivers/net/phy/Kconfig      |   5 +
 drivers/net/phy/Makefile     |   1 +
 drivers/net/phy/air_an8855.c | 261 +++++++++++++++++++++++++++++++++++
 4 files changed, 268 insertions(+)
 create mode 100644 drivers/net/phy/air_an8855.c

diff --git a/MAINTAINERS b/MAINTAINERS
index e285fa2702f5..41fb4d0d7fdb 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -734,6 +734,7 @@ F:	drivers/mfd/airoha-an8855.c
 F:	drivers/net/dsa/an8855.c
 F:	drivers/net/dsa/an8855.h
 F:	drivers/net/mdio/mdio-an8855.c
+F:	drivers/net/phy/air_an8855.c
 F:	drivers/nvmem/an8855-efuse.c
 
 AIROHA ETHERNET DRIVER
diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index d29f9f7fd2e1..e96f61b8eaba 100644
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -79,6 +79,11 @@ config SFP
 
 comment "MII PHY device drivers"
 
+config AIR_AN8855_PHY
+	tristate "Airoha AN8855 Internal Gigabit PHY"
+	help
+	  Currently supports the internal Airoha AN8855 Switch PHY.
+
 config AIR_EN8811H_PHY
 	tristate "Airoha EN8811H 2.5 Gigabit PHY"
 	help
diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
index 8f9ba5e8290d..d4f537ba006c 100644
--- a/drivers/net/phy/Makefile
+++ b/drivers/net/phy/Makefile
@@ -36,6 +36,7 @@ obj-y				+= $(sfp-obj-y) $(sfp-obj-m)
 
 obj-$(CONFIG_ADIN_PHY)		+= adin.o
 obj-$(CONFIG_ADIN1100_PHY)	+= adin1100.o
+obj-$(CONFIG_AIR_AN8855_PHY)   += air_an8855.o
 obj-$(CONFIG_AIR_EN8811H_PHY)   += air_en8811h.o
 obj-$(CONFIG_AMD_PHY)		+= amd.o
 obj-$(CONFIG_AMCC_QT2025_PHY)	+= qt2025.o
diff --git a/drivers/net/phy/air_an8855.c b/drivers/net/phy/air_an8855.c
new file mode 100644
index 000000000000..a740dbaacf9a
--- /dev/null
+++ b/drivers/net/phy/air_an8855.c
@@ -0,0 +1,261 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2024 Christian Marangi <ansuelsmth@gmail.com>
+ */
+
+#include <linux/bitfield.h>
+#include <linux/module.h>
+#include <linux/nvmem-consumer.h>
+#include <linux/of.h>
+#include <linux/phy.h>
+
+#define AN8855_PHY_SELECT_PAGE			0x1f
+#define   AN8855_PHY_PAGE			GENMASK(2, 0)
+#define   AN8855_PHY_PAGE_STANDARD		FIELD_PREP_CONST(AN8855_PHY_PAGE, 0x0)
+#define   AN8855_PHY_PAGE_EXTENDED_1		FIELD_PREP_CONST(AN8855_PHY_PAGE, 0x1)
+
+/* MII Registers Page 1 */
+#define AN8855_PHY_EXT_REG_14			0x14
+#define   AN8855_PHY_EN_DOWN_SHIFT		BIT(4)
+
+/* R50 Calibration regs in MDIO_MMD_VEND1 */
+#define AN8855_PHY_R500HM_RSEL_TX_AB		0x174
+#define AN8855_PHY_R50OHM_RSEL_TX_A_EN		BIT(15)
+#define AN8855_PHY_R50OHM_RSEL_TX_A		GENMASK(14, 8)
+#define AN8855_PHY_R50OHM_RSEL_TX_B_EN		BIT(7)
+#define AN8855_PHY_R50OHM_RSEL_TX_B		GENMASK(6, 0)
+#define AN8855_PHY_R500HM_RSEL_TX_CD		0x175
+#define AN8855_PHY_R50OHM_RSEL_TX_C_EN		BIT(15)
+#define AN8855_PHY_R50OHM_RSEL_TX_C		GENMASK(14, 8)
+#define AN8855_PHY_R50OHM_RSEL_TX_D_EN		BIT(7)
+#define AN8855_PHY_R50OHM_RSEL_TX_D		GENMASK(6, 0)
+
+#define AN8855_SWITCH_EFUSE_R50O		GENMASK(30, 24)
+
+/* PHY TX PAIR DELAY SELECT Register */
+#define AN8855_PHY_TX_PAIR_DLY_SEL_GBE		0x013
+#define   AN8855_PHY_CR_DA_TX_PAIR_DELKAY_SEL_A_GBE GENMASK(14, 12)
+#define   AN8855_PHY_CR_DA_TX_PAIR_DELKAY_SEL_B_GBE GENMASK(10, 8)
+#define   AN8855_PHY_CR_DA_TX_PAIR_DELKAY_SEL_C_GBE GENMASK(6, 4)
+#define   AN8855_PHY_CR_DA_TX_PAIR_DELKAY_SEL_D_GBE GENMASK(2, 0)
+/* PHY ADC Register */
+#define AN8855_PHY_RXADC_CTRL			0x0d8
+#define   AN8855_PHY_RG_AD_SAMNPLE_PHSEL_A	BIT(12)
+#define   AN8855_PHY_RG_AD_SAMNPLE_PHSEL_B	BIT(8)
+#define   AN8855_PHY_RG_AD_SAMNPLE_PHSEL_C	BIT(4)
+#define   AN8855_PHY_RG_AD_SAMNPLE_PHSEL_D	BIT(0)
+#define AN8855_PHY_RXADC_REV_0			0x0d9
+#define   AN8855_PHY_RG_AD_RESERVE0_A		GENMASK(15, 8)
+#define   AN8855_PHY_RG_AD_RESERVE0_B		GENMASK(7, 0)
+#define AN8855_PHY_RXADC_REV_1			0x0da
+#define   AN8855_PHY_RG_AD_RESERVE0_C		GENMASK(15, 8)
+#define   AN8855_PHY_RG_AD_RESERVE0_D		GENMASK(7, 0)
+
+#define AN8855_PHY_ID				0xc0ff0410
+
+struct air_an8855_priv {
+	bool needs_calibration;
+};
+
+static const u8 dsa_r50ohm_table[] = {
+	127, 127, 127, 127, 127, 127, 127, 127, 127, 127,
+	127, 127, 127, 127, 127, 127, 127, 126, 122, 117,
+	112, 109, 104, 101,  97,  94,  90,  88,  84,  80,
+	78,  74,  72,  68,  66,  64,  61,  58,  56,  53,
+	51,  48,  47,  44,  42,  40,  38,  36,  34,  32,
+	31,  28,  27,  24,  24,  22,  20,  18,  16,  16,
+	14,  12,  11,   9
+};
+
+static int en8855_get_r50ohm_val(struct device *dev, const char *calib_name,
+				 u8 *dest)
+{
+	u32 shift_sel, val;
+	int ret;
+	int i;
+
+	ret = nvmem_cell_read_u32(dev, calib_name, &val);
+	if (ret)
+		return ret;
+
+	shift_sel = FIELD_GET(AN8855_SWITCH_EFUSE_R50O, val);
+	for (i = 0; i < ARRAY_SIZE(dsa_r50ohm_table); i++)
+		if (dsa_r50ohm_table[i] == shift_sel)
+			break;
+
+	if (i < 8 || i >= ARRAY_SIZE(dsa_r50ohm_table))
+		*dest = dsa_r50ohm_table[25];
+	else
+		*dest = dsa_r50ohm_table[i - 8];
+
+	return 0;
+}
+
+static int an8855_probe(struct phy_device *phydev)
+{
+	struct device *dev = &phydev->mdio.dev;
+	struct air_an8855_priv *priv;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->needs_calibration = of_property_present(dev->of_node,
+						      "nvmem-cells");
+
+	phydev->priv = priv;
+
+	return 0;
+}
+
+static int an8855_get_downshift(struct phy_device *phydev, u8 *data)
+{
+	int val;
+
+	val = phy_read_paged(phydev, AN8855_PHY_PAGE_EXTENDED_1, AN8855_PHY_EXT_REG_14);
+	if (val < 0)
+		return val;
+
+	*data = val & AN8855_PHY_EN_DOWN_SHIFT ? DOWNSHIFT_DEV_DEFAULT_COUNT :
+						 DOWNSHIFT_DEV_DISABLE;
+
+	return 0;
+}
+
+static int an8855_set_downshift(struct phy_device *phydev, u8 cnt)
+{
+	u16 ds = cnt != DOWNSHIFT_DEV_DISABLE ? AN8855_PHY_EN_DOWN_SHIFT : 0;
+
+	return phy_modify_paged(phydev, AN8855_PHY_PAGE_EXTENDED_1,
+				AN8855_PHY_EXT_REG_14, AN8855_PHY_EN_DOWN_SHIFT,
+				ds);
+}
+
+static int an8855_config_init(struct phy_device *phydev)
+{
+	struct air_an8855_priv *priv = phydev->priv;
+	struct device *dev = &phydev->mdio.dev;
+	int ret;
+
+	/* Enable HW auto downshift */
+	ret = an8855_set_downshift(phydev, DOWNSHIFT_DEV_DEFAULT_COUNT);
+	if (ret)
+		return ret;
+
+	if (priv->needs_calibration) {
+		u8 calibration_data[4];
+
+		ret = en8855_get_r50ohm_val(dev, "tx_a", &calibration_data[0]);
+		if (ret)
+			return ret;
+
+		ret = en8855_get_r50ohm_val(dev, "tx_b", &calibration_data[1]);
+		if (ret)
+			return ret;
+
+		ret = en8855_get_r50ohm_val(dev, "tx_c", &calibration_data[2]);
+		if (ret)
+			return ret;
+
+		ret = en8855_get_r50ohm_val(dev, "tx_d", &calibration_data[3]);
+		if (ret)
+			return ret;
+
+		ret = phy_modify_mmd(phydev, MDIO_MMD_VEND1, AN8855_PHY_R500HM_RSEL_TX_AB,
+				     AN8855_PHY_R50OHM_RSEL_TX_A | AN8855_PHY_R50OHM_RSEL_TX_B,
+				     FIELD_PREP(AN8855_PHY_R50OHM_RSEL_TX_A, calibration_data[0]) |
+				     FIELD_PREP(AN8855_PHY_R50OHM_RSEL_TX_B, calibration_data[1]));
+		if (ret)
+			return ret;
+		ret = phy_modify_mmd(phydev, MDIO_MMD_VEND1, AN8855_PHY_R500HM_RSEL_TX_CD,
+				     AN8855_PHY_R50OHM_RSEL_TX_C | AN8855_PHY_R50OHM_RSEL_TX_D,
+				     FIELD_PREP(AN8855_PHY_R50OHM_RSEL_TX_C, calibration_data[2]) |
+				     FIELD_PREP(AN8855_PHY_R50OHM_RSEL_TX_D, calibration_data[3]));
+		if (ret)
+			return ret;
+	}
+
+	/* Apply values to reduce signal noise */
+	ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, AN8855_PHY_TX_PAIR_DLY_SEL_GBE,
+			    FIELD_PREP(AN8855_PHY_CR_DA_TX_PAIR_DELKAY_SEL_A_GBE, 0x4) |
+			    FIELD_PREP(AN8855_PHY_CR_DA_TX_PAIR_DELKAY_SEL_C_GBE, 0x4));
+	if (ret)
+		return ret;
+	ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, AN8855_PHY_RXADC_CTRL,
+			    AN8855_PHY_RG_AD_SAMNPLE_PHSEL_A |
+			    AN8855_PHY_RG_AD_SAMNPLE_PHSEL_C);
+	if (ret)
+		return ret;
+	ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, AN8855_PHY_RXADC_REV_0,
+			    FIELD_PREP(AN8855_PHY_RG_AD_RESERVE0_A, 0x1));
+	if (ret)
+		return ret;
+	ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, AN8855_PHY_RXADC_REV_1,
+			    FIELD_PREP(AN8855_PHY_RG_AD_RESERVE0_C, 0x1));
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static int an8855_get_tunable(struct phy_device *phydev,
+			      struct ethtool_tunable *tuna, void *data)
+{
+	switch (tuna->id) {
+	case ETHTOOL_PHY_DOWNSHIFT:
+		return an8855_get_downshift(phydev, data);
+	default:
+		return -EOPNOTSUPP;
+	}
+}
+
+static int an8855_set_tunable(struct phy_device *phydev,
+			      struct ethtool_tunable *tuna, const void *data)
+{
+	switch (tuna->id) {
+	case ETHTOOL_PHY_DOWNSHIFT:
+		return an8855_set_downshift(phydev, *(const u8 *)data);
+	default:
+		return -EOPNOTSUPP;
+	}
+}
+
+static int an8855_read_page(struct phy_device *phydev)
+{
+	return __phy_read(phydev, AN8855_PHY_SELECT_PAGE);
+}
+
+static int an8855_write_page(struct phy_device *phydev, int page)
+{
+	return __phy_write(phydev, AN8855_PHY_SELECT_PAGE, page);
+}
+
+static struct phy_driver an8855_driver[] = {
+{
+	PHY_ID_MATCH_EXACT(AN8855_PHY_ID),
+	.name			= "Airoha AN8855 internal PHY",
+	/* PHY_GBIT_FEATURES */
+	.flags			= PHY_IS_INTERNAL,
+	.probe			= an8855_probe,
+	.config_init		= an8855_config_init,
+	.soft_reset		= genphy_soft_reset,
+	.get_tunable		= an8855_get_tunable,
+	.set_tunable		= an8855_set_tunable,
+	.suspend		= genphy_suspend,
+	.resume			= genphy_resume,
+	.read_page		= an8855_read_page,
+	.write_page		= an8855_write_page,
+}, };
+
+module_phy_driver(an8855_driver);
+
+static struct mdio_device_id __maybe_unused an8855_tbl[] = {
+	{ PHY_ID_MATCH_EXACT(AN8855_PHY_ID) },
+	{ }
+};
+
+MODULE_DEVICE_TABLE(mdio, an8855_tbl);
+
+MODULE_DESCRIPTION("Airoha AN8855 PHY driver");
+MODULE_AUTHOR("Christian Marangi <ansuelsmth@gmail.com>");
+MODULE_LICENSE("GPL");
-- 
2.48.1

Re: [net-next PATCH v13 05/14] dt-bindings: mfd: Document support for Airoha AN8855 Switch SoC

[Rob Herring (Arm)]

On Sat, 15 Mar 2025 16:43:45 +0100, Christian Marangi wrote:
> Document support for Airoha AN8855 Switch SoC. This SoC expose various
> peripherals like an Ethernet Switch, a NVMEM provider and Ethernet PHYs.
> 
> It does also support i2c and timers but those are not currently
> supported/used.
> 
> Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
> ---
>  .../bindings/mfd/airoha,an8855.yaml           | 182 ++++++++++++++++++
>  MAINTAINERS                                   |   1 +
>  2 files changed, 183 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/mfd/airoha,an8855.yaml
> 

My bot found errors running 'make dt_binding_check' on your patch:

yamllint warnings/errors:

dtschema/dtc warnings/errors:
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mfd/airoha,an8855.example.dtb: phy@1: $nodename:0: 'phy@1' does not match '^ethernet-phy(@[a-f0-9]+)?$'
	from schema $id: http://devicetree.org/schemas/net/airoha,an8855-phy.yaml#
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mfd/airoha,an8855.example.dtb: phy@1: Unevaluated properties are not allowed ('compatible' was unexpected)
	from schema $id: http://devicetree.org/schemas/net/airoha,an8855-phy.yaml#
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mfd/airoha,an8855.example.dtb: phy@2: $nodename:0: 'phy@2' does not match '^ethernet-phy(@[a-f0-9]+)?$'
	from schema $id: http://devicetree.org/schemas/net/airoha,an8855-phy.yaml#
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mfd/airoha,an8855.example.dtb: phy@2: Unevaluated properties are not allowed ('compatible' was unexpected)
	from schema $id: http://devicetree.org/schemas/net/airoha,an8855-phy.yaml#

doc reference errors (make refcheckdocs):

See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20250315154407.26304-6-ansuelsmth@gmail.com

The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.

Re: [net-next PATCH v13 05/14] dt-bindings: mfd: Document support for Airoha AN8855 Switch SoC

[Rob Herring]

On Sat, Mar 15, 2025 at 04:43:45PM +0100, Christian Marangi wrote:
> Document support for Airoha AN8855 Switch SoC. This SoC expose various
> peripherals like an Ethernet Switch, a NVMEM provider and Ethernet PHYs.
> 
> It does also support i2c and timers but those are not currently
> supported/used.
> 
> Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
> ---
>  .../bindings/mfd/airoha,an8855.yaml           | 182 ++++++++++++++++++
>  MAINTAINERS                                   |   1 +
>  2 files changed, 183 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/mfd/airoha,an8855.yaml
> 
> diff --git a/Documentation/devicetree/bindings/mfd/airoha,an8855.yaml b/Documentation/devicetree/bindings/mfd/airoha,an8855.yaml
> new file mode 100644
> index 000000000000..a59a23056b3a
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/airoha,an8855.yaml
> @@ -0,0 +1,182 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/mfd/airoha,an8855.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Airoha AN8855 Switch SoC
> +
> +maintainers:
> +  - Christian Marangi <ansuelsmth@gmail.com>
> +
> +description: >
> +  Airoha AN8855 Switch is a SoC that expose various peripherals like an
> +  Ethernet Switch, a NVMEM provider and Ethernet PHYs.
> +
> +  It does also support i2c and timers but those are not currently
> +  supported/used.
> +
> +properties:
> +  compatible:
> +    const: airoha,an8855
> +
> +  reg:
> +    maxItems: 1
> +
> +  reset-gpios: true
> +
> +  efuse:
> +    type: object
> +    $ref: /schemas/nvmem/airoha,an8855-efuse.yaml
> +    description:
> +      EFUSE exposed by the Airoha AN8855 Switch. This child node definition
> +      should follow the bindings specified in
> +      Documentation/devicetree/bindings/nvmem/airoha,an8855-efuse.yaml

No need to list the schema twice. Drop the 2nd sentence.

> +
> +  ethernet-switch:
> +    type: object
> +    $ref: /schemas/net/dsa/airoha,an8855-switch.yaml
> +    description:
> +      Switch exposed by the Airoha AN8855 Switch. This child node definition
> +      should follow the bindings specified in
> +      Documentation/devicetree/bindings/net/dsa/airoha,an8855-switch.yaml

ditto

> +
> +  mdio:
> +    type: object
> +    $ref: /schemas/net/airoha,an8855-mdio.yaml
> +    description:
> +      MDIO exposed by the Airoha AN8855 Switch. This child node definition
> +      should follow the bindings specified in
> +      Documentation/devicetree/bindings/net/airoha,an8855-mdio.yaml

ditto

> +
> +required:
> +  - compatible
> +  - reg

The child nodes are optional?

> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/gpio/gpio.h>
> +
> +    mdio {
> +        #address-cells = <1>;
> +        #size-cells = <0>;
> +
> +        soc@1 {
> +            compatible = "airoha,an8855";
> +            reg = <1>;
> +
> +            reset-gpios = <&pio 39 0>;
> +
> +            efuse {
> +                compatible = "airoha,an8855-efuse";
> +
> +                #nvmem-cell-cells = <0>;
> +
> +                nvmem-layout {
> +                    compatible = "fixed-layout";
> +                    #address-cells = <1>;
> +                    #size-cells = <1>;
> +
> +                    shift_sel_port0_tx_a: shift-sel-port0-tx-a@c {
> +                       reg = <0xc 0x4>;
> +                    };
> +
> +                    shift_sel_port0_tx_b: shift-sel-port0-tx-b@10 {
> +                        reg = <0x10 0x4>;
> +                    };
> +
> +                    shift_sel_port0_tx_c: shift-sel-port0-tx-c@14 {
> +                        reg = <0x14 0x4>;
> +                    };
> +
> +                    shift_sel_port0_tx_d: shift-sel-port0-tx-d@18 {
> +                       reg = <0x18 0x4>;
> +                    };
> +
> +                    shift_sel_port1_tx_a: shift-sel-port1-tx-a@1c {
> +                        reg = <0x1c 0x4>;
> +                    };
> +
> +                    shift_sel_port1_tx_b: shift-sel-port1-tx-b@20 {
> +                        reg = <0x20 0x4>;
> +                    };
> +
> +                    shift_sel_port1_tx_c: shift-sel-port1-tx-c@24 {
> +                       reg = <0x24 0x4>;
> +                    };
> +
> +                    shift_sel_port1_tx_d: shift-sel-port1-tx-d@28 {
> +                        reg = <0x28 0x4>;
> +                    };
> +                };
> +            };
> +
> +            ethernet-switch {
> +                compatible = "airoha,an8855-switch";
> +
> +                ports {
> +                    #address-cells = <1>;
> +                    #size-cells = <0>;
> +
> +                    port@0 {
> +                        reg = <0>;
> +                        label = "lan1";
> +                        phy-mode = "internal";
> +                        phy-handle = <&internal_phy1>;
> +                    };
> +
> +                    port@1 {
> +                        reg = <1>;
> +                        label = "lan2";
> +                        phy-mode = "internal";
> +                        phy-handle = <&internal_phy2>;
> +                    };
> +
> +                    port@5 {
> +                        reg = <5>;
> +                        label = "cpu";
> +                        ethernet = <&gmac0>;
> +                        phy-mode = "2500base-x";
> +
> +                        fixed-link {
> +                            speed = <2500>;
> +                            full-duplex;
> +                            pause;
> +                        };
> +                    };
> +                };
> +            };
> +
> +            mdio {
> +                compatible = "airoha,an8855-mdio";
> +                #address-cells = <1>;
> +                #size-cells = <0>;
> +
> +                internal_phy1: phy@1 {
> +                  compatible = "ethernet-phy-idc0ff.0410",
> +                               "ethernet-phy-ieee802.3-c45";
> +                  reg = <1>;
> +
> +                  nvmem-cells = <&shift_sel_port0_tx_a>,
> +                      <&shift_sel_port0_tx_b>,
> +                      <&shift_sel_port0_tx_c>,
> +                      <&shift_sel_port0_tx_d>;
> +                  nvmem-cell-names = "tx_a", "tx_b", "tx_c", "tx_d";
> +                };
> +
> +                internal_phy2: phy@2 {
> +                  compatible = "ethernet-phy-idc0ff.0410",
> +                               "ethernet-phy-ieee802.3-c45";
> +                  reg = <2>;
> +
> +                  nvmem-cells = <&shift_sel_port1_tx_a>,
> +                      <&shift_sel_port1_tx_b>,
> +                      <&shift_sel_port1_tx_c>,
> +                      <&shift_sel_port1_tx_d>;
> +                  nvmem-cell-names = "tx_a", "tx_b", "tx_c", "tx_d";
> +                };
> +            };
> +        };
> +    };
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 45f4bb8deb0d..65709e47adc7 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -725,6 +725,7 @@ L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
>  L:	linux-mediatek@lists.infradead.org (moderated for non-subscribers)
>  L:	netdev@vger.kernel.org
>  S:	Maintained
> +F:	Documentation/devicetree/bindings/mfd/airoha,an8855.yaml
>  F:	Documentation/devicetree/bindings/net/airoha,an8855-mdio.yaml
>  F:	Documentation/devicetree/bindings/net/airoha,an8855-phy.yaml
>  F:	Documentation/devicetree/bindings/net/dsa/airoha,an8855-switch.yaml
> -- 
> 2.48.1
> 

Re: [net-next PATCH v13 03/14] dt-bindings: net: dsa: Document support for Airoha AN8855 DSA Switch

[Rob Herring (Arm)]

On Sat, 15 Mar 2025 16:43:43 +0100, Christian Marangi wrote:
> Document support for Airoha AN8855 5-port Gigabit Switch.
> 
> It does expose the 5 Internal PHYs on the MDIO bus and each port
> can access the Switch register space by configurting the PHY page.
> 
> Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
> ---
>  .../net/dsa/airoha,an8855-switch.yaml         | 86 +++++++++++++++++++
>  MAINTAINERS                                   |  1 +
>  2 files changed, 87 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/net/dsa/airoha,an8855-switch.yaml
> 

Reviewed-by: Rob Herring (Arm) <robh@kernel.org>

Re: [net-next PATCH v13 04/14] dt-bindings: net: Document support for AN8855 Switch Internal PHY

[Rob Herring (Arm)]

On Sat, 15 Mar 2025 16:43:44 +0100, Christian Marangi wrote:
> Document support for AN8855 Switch Internal PHY.
> 
> Airoha AN8855 is a 5-port Gigabit Switch that expose the Internal
> PHYs on the MDIO bus.
> 
> Each PHY might need to be calibrated to correctly work with the
> use of the eFUSE provided by the Switch SoC. This can be enabled by
> defining in the PHY node the NVMEM cell properties.
> 
> Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
> ---
>  .../bindings/net/airoha,an8855-phy.yaml       | 83 +++++++++++++++++++
>  MAINTAINERS                                   |  1 +
>  2 files changed, 84 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/net/airoha,an8855-phy.yaml
> 

Reviewed-by: Rob Herring (Arm) <robh@kernel.org>

Re: [net-next PATCH v13 13/14] net: dsa: Add Airoha AN8855 5-Port Gigabit DSA Switch driver

[Vladimir Oltean]

On Sat, Mar 15, 2025 at 04:43:53PM +0100, Christian Marangi wrote:
> +/* Similar to MT7530 also trap link local frame and special frame to CPU */
> +static int an8855_trap_special_frames(struct an8855_priv *priv)
> +{
> +	int ret;
> +
> +	/* Trap BPDUs to the CPU port(s) and egress them
> +	 * VLAN-untagged.
> +	 */
> +	ret = regmap_update_bits(priv->regmap, AN8855_BPC,
> +				 AN8855_BPDU_BPDU_FR | AN8855_BPDU_EG_TAG |
> +				 AN8855_BPDU_PORT_FW,
> +				 AN8855_BPDU_BPDU_FR |
> +				 FIELD_PREP(AN8855_BPDU_EG_TAG, AN8855_VLAN_EG_UNTAGGED) |
> +				 FIELD_PREP(AN8855_BPDU_PORT_FW, AN8855_BPDU_CPU_ONLY));
> +	if (ret)
> +		return ret;
> +
> +	/* Trap 802.1X PAE frames to the CPU port(s) and egress them
> +	 * VLAN-untagged.
> +	 */
> +	ret = regmap_update_bits(priv->regmap, AN8855_PAC,
> +				 AN8855_PAE_BPDU_FR | AN8855_PAE_EG_TAG |
> +				 AN8855_PAE_PORT_FW,
> +				 AN8855_PAE_BPDU_FR |
> +				 FIELD_PREP(AN8855_PAE_EG_TAG, AN8855_VLAN_EG_UNTAGGED) |
> +				 FIELD_PREP(AN8855_PAE_PORT_FW, AN8855_BPDU_CPU_ONLY));
> +	if (ret)
> +		return ret;
> +
> +	/* Trap frames with :01 MAC DAs to the CPU port(s) and egress
> +	 * them VLAN-untagged.
> +	 */
> +	ret = regmap_update_bits(priv->regmap, AN8855_RGAC1,
> +				 AN8855_R01_BPDU_FR | AN8855_R01_EG_TAG |
> +				 AN8855_R01_PORT_FW,
> +				 AN8855_R01_BPDU_FR |
> +				 FIELD_PREP(AN8855_R01_EG_TAG, AN8855_VLAN_EG_UNTAGGED) |
> +				 FIELD_PREP(AN8855_R01_PORT_FW, AN8855_BPDU_CPU_ONLY));
> +	if (ret)
> +		return ret;
> +
> +	/* Trap frames with :02 MAC DAs to the CPU port(s) and egress
> +	 * them VLAN-untagged.
> +	 */
> +	ret = regmap_update_bits(priv->regmap, AN8855_RGAC1,
> +				 AN8855_R02_BPDU_FR | AN8855_R02_EG_TAG |
> +				 AN8855_R02_PORT_FW,
> +				 AN8855_R02_BPDU_FR |
> +				 FIELD_PREP(AN8855_R02_EG_TAG, AN8855_VLAN_EG_UNTAGGED) |
> +				 FIELD_PREP(AN8855_R02_PORT_FW, AN8855_BPDU_CPU_ONLY));
> +	if (ret)
> +		return ret;
> +
> +	/* Trap frames with :03 MAC DAs to the CPU port(s) and egress
> +	 * them VLAN-untagged.
> +	 */
> +	ret = regmap_update_bits(priv->regmap, AN8855_RGAC1,
> +				 AN8855_R03_BPDU_FR | AN8855_R03_EG_TAG |
> +				 AN8855_R03_PORT_FW,
> +				 AN8855_R03_BPDU_FR |
> +				 FIELD_PREP(AN8855_R03_EG_TAG, AN8855_VLAN_EG_UNTAGGED) |
> +				 FIELD_PREP(AN8855_R03_PORT_FW, AN8855_BPDU_CPU_ONLY));
> +	if (ret)
> +		return ret;
> +
> +	/* Trap frames with :0E MAC DAs to the CPU port(s) and egress
> +	 * them VLAN-untagged.
> +	 */
> +	return regmap_update_bits(priv->regmap, AN8855_RGAC1,
> +				  AN8855_R0E_BPDU_FR | AN8855_R0E_EG_TAG |
> +				  AN8855_R0E_PORT_FW,
> +				  AN8855_R0E_BPDU_FR |
> +				  FIELD_PREP(AN8855_R0E_EG_TAG, AN8855_VLAN_EG_UNTAGGED) |
> +				  FIELD_PREP(AN8855_R0E_PORT_FW, AN8855_BPDU_CPU_ONLY));
> +}

Is there a way in which you could group the registers a bit more?
The function occupies 2 screens :-/

There are 4 read-modify-write operations in succession to the RGAC1
register. Maybe you can converge them into a single regmap_update_bits()
call.

Also, for packets which reach the CPU via a trap, we shouldn't set
skb->offload_fwd_mark = 1. In other words, if the bridge layer wants to
forward them in software (including to other an8855 ports), let it do so.
The common example given in commit 515853ccecc6 ("bridge: allow
forwarding some link local frames") is 802.1X PAE (01-80-C2-00-00-03).

I notice mtk_tag_rcv() calls dsa_default_offload_fwd_mark() with no
pre-condition. Do you know whether there exists any bit in the RX tag
which signifies whether the packet was received because of a trap
(or if it was autonomously forwarded by the switch to the other bridge
ports as well)? The offload_fwd_mark bit should be set based on
something like that.

Re: [net-next PATCH v13 10/14] mfd: an8855: Add support for Airoha AN8855 Switch MFD

[kernel test robot]

Hi Christian,

kernel test robot noticed the following build errors:

[auto build test ERROR on net-next/main]

url:    https://github.com/intel-lab-lkp/linux/commits/Christian-Marangi/dt-bindings-nvmem-Document-support-for-Airoha-AN8855-Switch-EFUSE/20250315-235040
base:   net-next/main
patch link:    https://lore.kernel.org/r/20250315154407.26304-11-ansuelsmth%40gmail.com
patch subject: [net-next PATCH v13 10/14] mfd: an8855: Add support for Airoha AN8855 Switch MFD
config: i386-randconfig-006-20250321 (https://download.01.org/0day-ci/archive/20250321/202503211428.H4VdWHco-lkp@intel.com/config)
compiler: gcc-12 (Debian 12.2.0-14) 12.2.0
reproduce (this is a W=1 build): (https://download.01.org/0day-ci/archive/20250321/202503211428.H4VdWHco-lkp@intel.com/reproduce)

If you fix the issue in a separate patch/commit (i.e. not just a new version of
the same patch/commit), kindly add following tags
| Reported-by: kernel test robot <lkp@intel.com>
| Closes: https://lore.kernel.org/oe-kbuild-all/202503211428.H4VdWHco-lkp@intel.com/

All errors (new ones prefixed by >>):

   ld: drivers/mfd/airoha-an8855.o: in function `an8855_core_probe':
>> drivers/mfd/airoha-an8855.c:376: undefined reference to `devm_mdio_regmap_init'


vim +376 drivers/mfd/airoha-an8855.c

   352	
   353	static int an8855_core_probe(struct mdio_device *mdiodev)
   354	{
   355		struct regmap *regmap, *regmap_phy;
   356		struct device *dev = &mdiodev->dev;
   357		struct an8855_core_priv *priv;
   358		struct gpio_desc *reset_gpio;
   359		u32 val;
   360		int ret;
   361	
   362		priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
   363		if (!priv)
   364			return -ENOMEM;
   365	
   366		priv->bus = mdiodev->bus;
   367		priv->switch_addr = mdiodev->addr;
   368		/* No DMA for mdiobus, mute warning for DMA mask not set */
   369		dev->dma_mask = &dev->coherent_dma_mask;
   370	
   371		regmap = devm_regmap_init(dev, NULL, priv, &an8855_regmap_config);
   372		if (IS_ERR(regmap))
   373			return dev_err_probe(dev, PTR_ERR(regmap),
   374					     "regmap initialization failed\n");
   375	
 > 376		regmap_phy = devm_mdio_regmap_init(dev, priv, &an8855_regmap_phy_config);
   377		if (IS_ERR(regmap_phy))
   378			return dev_err_probe(dev, PTR_ERR(regmap_phy),
   379					     "regmap phy initialization failed\n");
   380	
   381		reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
   382		if (IS_ERR(reset_gpio))
   383			return PTR_ERR(reset_gpio);
   384	
   385		if (reset_gpio) {
   386			usleep_range(100000, 150000);
   387			gpiod_set_value_cansleep(reset_gpio, 0);
   388			usleep_range(100000, 150000);
   389			gpiod_set_value_cansleep(reset_gpio, 1);
   390	
   391			/* Poll HWTRAP reg to wait for Switch to fully Init */
   392			ret = regmap_read_poll_timeout(regmap, AN8855_HWTRAP, val,
   393						       val, 20, 200000);
   394			if (ret)
   395				return ret;
   396		}
   397	
   398		ret = an8855_read_switch_id(dev, regmap);
   399		if (ret)
   400			return ret;
   401	
   402		/* Release global PHY power down */
   403		ret = regmap_write(regmap, AN8855_RG_GPHY_AFE_PWD, 0x0);
   404		if (ret)
   405			return ret;
   406	
   407		return devm_mfd_add_devices(dev, PLATFORM_DEVID_AUTO, an8855_core_childs,
   408					    ARRAY_SIZE(an8855_core_childs), NULL, 0,
   409					    NULL);
   410	}
   411	

-- 
0-DAY CI Kernel Test Service
https://github.com/intel/lkp-tests/wiki

Re: [net-next PATCH v13 10/14] mfd: an8855: Add support for Airoha AN8855 Switch MFD

[Lee Jones]

On Sat, 15 Mar 2025, Christian Marangi wrote:

> Add support for Airoha AN8855 Switch MFD that provide support for a DSA
> switch and a NVMEM provider. Also provide support for a virtual MDIO
> passthrough as the PHYs address for the switch are shared with the switch
> address.
> 
> Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
> ---
>  MAINTAINERS                 |   1 +

This won't apply before the others.  If I were you, I'd pull this change
out of here and add a MAINTAINERS entry as the final patch.

>  drivers/mfd/Kconfig         |  12 +
>  drivers/mfd/Makefile        |   1 +
>  drivers/mfd/airoha-an8855.c | 429 ++++++++++++++++++++++++++++++++++++
>  4 files changed, 443 insertions(+)
>  create mode 100644 drivers/mfd/airoha-an8855.c

-- 
Lee Jones [李琼斯]

Re: [net-next PATCH v13 13/14] net: dsa: Add Airoha AN8855 5-Port Gigabit DSA Switch driver

[Christian Marangi]

On Tue, Mar 18, 2025 at 05:15:40PM +0200, Vladimir Oltean wrote:
> On Sat, Mar 15, 2025 at 04:43:53PM +0100, Christian Marangi wrote:
> > +/* Similar to MT7530 also trap link local frame and special frame to CPU */
> > +static int an8855_trap_special_frames(struct an8855_priv *priv)
> > +{
> > +	int ret;
> > +
> > +	/* Trap BPDUs to the CPU port(s) and egress them
> > +	 * VLAN-untagged.
> > +	 */
> > +	ret = regmap_update_bits(priv->regmap, AN8855_BPC,
> > +				 AN8855_BPDU_BPDU_FR | AN8855_BPDU_EG_TAG |
> > +				 AN8855_BPDU_PORT_FW,
> > +				 AN8855_BPDU_BPDU_FR |
> > +				 FIELD_PREP(AN8855_BPDU_EG_TAG, AN8855_VLAN_EG_UNTAGGED) |
> > +				 FIELD_PREP(AN8855_BPDU_PORT_FW, AN8855_BPDU_CPU_ONLY));
> > +	if (ret)
> > +		return ret;
> > +
> > +	/* Trap 802.1X PAE frames to the CPU port(s) and egress them
> > +	 * VLAN-untagged.
> > +	 */
> > +	ret = regmap_update_bits(priv->regmap, AN8855_PAC,
> > +				 AN8855_PAE_BPDU_FR | AN8855_PAE_EG_TAG |
> > +				 AN8855_PAE_PORT_FW,
> > +				 AN8855_PAE_BPDU_FR |
> > +				 FIELD_PREP(AN8855_PAE_EG_TAG, AN8855_VLAN_EG_UNTAGGED) |
> > +				 FIELD_PREP(AN8855_PAE_PORT_FW, AN8855_BPDU_CPU_ONLY));
> > +	if (ret)
> > +		return ret;
> > +
> > +	/* Trap frames with :01 MAC DAs to the CPU port(s) and egress
> > +	 * them VLAN-untagged.
> > +	 */
> > +	ret = regmap_update_bits(priv->regmap, AN8855_RGAC1,
> > +				 AN8855_R01_BPDU_FR | AN8855_R01_EG_TAG |
> > +				 AN8855_R01_PORT_FW,
> > +				 AN8855_R01_BPDU_FR |
> > +				 FIELD_PREP(AN8855_R01_EG_TAG, AN8855_VLAN_EG_UNTAGGED) |
> > +				 FIELD_PREP(AN8855_R01_PORT_FW, AN8855_BPDU_CPU_ONLY));
> > +	if (ret)
> > +		return ret;
> > +
> > +	/* Trap frames with :02 MAC DAs to the CPU port(s) and egress
> > +	 * them VLAN-untagged.
> > +	 */
> > +	ret = regmap_update_bits(priv->regmap, AN8855_RGAC1,
> > +				 AN8855_R02_BPDU_FR | AN8855_R02_EG_TAG |
> > +				 AN8855_R02_PORT_FW,
> > +				 AN8855_R02_BPDU_FR |
> > +				 FIELD_PREP(AN8855_R02_EG_TAG, AN8855_VLAN_EG_UNTAGGED) |
> > +				 FIELD_PREP(AN8855_R02_PORT_FW, AN8855_BPDU_CPU_ONLY));
> > +	if (ret)
> > +		return ret;
> > +
> > +	/* Trap frames with :03 MAC DAs to the CPU port(s) and egress
> > +	 * them VLAN-untagged.
> > +	 */
> > +	ret = regmap_update_bits(priv->regmap, AN8855_RGAC1,
> > +				 AN8855_R03_BPDU_FR | AN8855_R03_EG_TAG |
> > +				 AN8855_R03_PORT_FW,
> > +				 AN8855_R03_BPDU_FR |
> > +				 FIELD_PREP(AN8855_R03_EG_TAG, AN8855_VLAN_EG_UNTAGGED) |
> > +				 FIELD_PREP(AN8855_R03_PORT_FW, AN8855_BPDU_CPU_ONLY));
> > +	if (ret)
> > +		return ret;
> > +
> > +	/* Trap frames with :0E MAC DAs to the CPU port(s) and egress
> > +	 * them VLAN-untagged.
> > +	 */
> > +	return regmap_update_bits(priv->regmap, AN8855_RGAC1,
> > +				  AN8855_R0E_BPDU_FR | AN8855_R0E_EG_TAG |
> > +				  AN8855_R0E_PORT_FW,
> > +				  AN8855_R0E_BPDU_FR |
> > +				  FIELD_PREP(AN8855_R0E_EG_TAG, AN8855_VLAN_EG_UNTAGGED) |
> > +				  FIELD_PREP(AN8855_R0E_PORT_FW, AN8855_BPDU_CPU_ONLY));
> > +}
> 
> Is there a way in which you could group the registers a bit more?
> The function occupies 2 screens :-/
>

I will use local variable and pack it.

> There are 4 read-modify-write operations in succession to the RGAC1
> register. Maybe you can converge them into a single regmap_update_bits()
> call.
> 
> Also, for packets which reach the CPU via a trap, we shouldn't set
> skb->offload_fwd_mark = 1. In other words, if the bridge layer wants to
> forward them in software (including to other an8855 ports), let it do so.
> The common example given in commit 515853ccecc6 ("bridge: allow
> forwarding some link local frames") is 802.1X PAE (01-80-C2-00-00-03).
> 
> I notice mtk_tag_rcv() calls dsa_default_offload_fwd_mark() with no
> pre-condition. Do you know whether there exists any bit in the RX tag
> which signifies whether the packet was received because of a trap
> (or if it was autonomously forwarded by the switch to the other bridge
> ports as well)? The offload_fwd_mark bit should be set based on
> something like that.


I did some simulation checking the full tag and also yesterday Airoha
confirmed that those register doesn't affect the CPU tag.

There is an entry in the TAG that signal some kind of packet but it
doesn't react. From what I can see it only comunicate when fdb or other
really special thing.

-- 
	Ansuel