[PATCH v4 0/3] Add Luckfox Omni3576 Carrier Board support for RK3576

[PATCH v4 0/3] Add Luckfox Omni3576 Carrier Board support for RK3576

[John Clark]

This series adds device tree support for the Luckfox Omni3576 Carrier
Board with the Core3576 Module, powered by the Rockchip RK3576 SoC
(four Cortex-A72 cores, four Cortex-A53 cores, Mali-G52 MC3 GPU). It
enables essential functionality for booting Linux and basic connectivity,
with plans for future support of peripherals like WiFi, MIPI-DSI, HDMI,
and Ethernet.

Tested features (on Linux 6.15-rc4):
 - UART: Serial console operational
 - SD card: Mounts and reads/writes successfully
 - PCIe: NVMe SSD detected, mounted, and fully functional
 - USB 2.0: Host ports operational
 - RTC: Timekeeping and wake-up tested
 - LED: Heartbeat trigger functional
 - eMMC: Enabled in device tree, not populated on tested hardware

The series includes three patches:
 1. dt-bindings: vendor-prefixes: Add Luckfox vendor prefix
 2. dt-bindings: arm: rockchip: Add Luckfox Omni3576 and Core3576 bindings
 3. arm64: dts: rockchip: Add Luckfox Omni3576 board support

The device tree is covered by the existing ROCKCHIP ARCHITECTURE entry in
MAINTAINERS. I am aware of ongoing RK3576 upstreaming efforts (e.g., by
Collabora) and welcome feedback or collaboration to align with mainline
driver development.

Changes in v4:
 - Patch 1: Unchanged, Acked-by: Conor Dooley <conor.dooley@microchip.com>.
 - Patch 2: Fixed binding for Omni3576 Carrier Board to use correct enum
   syntax (enum: [luckfox,omni3576] instead of invalid const), added
   luckfox,core3576 to compatible string to reflect module dependency.
 - Patch 3: Updated compatible string in rk3576-luckfox-omni3576.dts to
   match revised binding ("luckfox,omni3576", "luckfox,core3576",
   "rockchip,rk3576").

Changes in v3:
 - Split device tree into rk3576-luckfox-core3576.dtsi (module) and
   rk3576-luckfox-omni3576.dts (carrier board) for better modularity.
   Previous Acked-by from Krzysztof Kozlowski for Patch 2 no longer applies
   due to substantial changes.
 - Addressed Jonas Karlman's feedback on patch 3/3 (Luckfox Omni3576
   device tree):
   - Added pinctrl for green LED GPIO (gpio1 RK_PD5) for proper pin setup.
   - Reordered regulator node properties for consistent sequence (e.g.,
     regulator-name, regulator-min-microvolt, regulator-max-microvolt,
     etc.).
   - Updated regulator nodes (vcc_3v3_pcie, vbus_5v0_typec, vcc_5v0_host,
     vcc_5v0_hdmi) to use 'gpios' property instead of deprecated 'gpio'.
   - Removed pmic-power-off pinctrl state and pinctrl-1 from RK806 PMIC
     node, as they are vendor-specific and undocumented in bindings.
   - Removed pwrkey node from PMIC, as it lacks binding documentation.
   - Added blank line between properties and child nodes in i2c2 node for
     DT style compliance.
   - Removed no-mmc property from sdmmc node to enable MMC support,
     aligning with RK3576 SD v3.0 and MMC v4.51 capabilities, allowing TF
     card slot to support MMC devices or eMMC via adapter.
 - Removed Ethernet support (gmac0/gmac1 nodes) per Andrew Lunn's
   feedback, as it used the generic PHY driver with incorrect RGMII delay
   settings, incompatible with the upcoming MAE0621A driver.
   Collaborating with Andrew Lunn on a device driver, with Ethernet
   support to be submitted separately when complete.
 - Addressed Rob Herring's DTB check warnings, other warnings (e.g., VOP,
   PCIe, OTP, HDMI PHY) originate from rk3576.dtsi and are outside this
   patchset scope.
 - Added RNG node to pick up Nicolas Frattaroli's "add RK3576 RNG node"
   patch.

Changes in v2:
 - Enabled HDMI node per feedback from Heiko Stuebner and Nicolas
   Frattaroli; untested due to upstream driver issues.
 - Enabled Ethernet 1 node per Heiko's device tree philosophy; untested
   due to suspected PHY driver or configuration issues (removed in v3 per
   Andrew Lunn).
 - Clarified eMMC remains enabled but unpopulated on tested board, per
   Heiko.

Signed-off-by: John Clark <inindev@gmail.com>
---
John Clark (3):
  dt-bindings: vendor-prefixes: Add luckfox prefix
  dt-bindings: arm: rockchip: Add Luckfox Omni3576 and Core3576 bindings
  arm64: dts: rockchip: Add Luckfox Omni3576 Board support

 .../devicetree/bindings/arm/rockchip.yaml     |   7 +
 .../devicetree/bindings/vendor-prefixes.yaml  |   2 +
 arch/arm64/boot/dts/rockchip/Makefile         |   1 +
 .../dts/rockchip/rk3576-luckfox-core3576.dtsi | 683 ++++++++++++++++++
 .../dts/rockchip/rk3576-luckfox-omni3576.dts  |  53 ++
 5 files changed, 746 insertions(+)
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3576-luckfox-core3576.dtsi
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3576-luckfox-omni3576.dts

-- 
2.39.5

[PATCH v4 1/3] dt-bindings: vendor-prefixes: Add luckfox prefix

[John Clark]

Add vendor prefix for Shenzhen Luckfox Technology Co., Ltd., which
produces development boards like the Luckfox Omni3576.

Signed-off-by: John Clark <inindev@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
---
 Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 86f6a19b28ae..9391e0c31bb8 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -892,6 +892,8 @@ patternProperties:
     description: Liebherr-Werk Nenzing GmbH
   "^lxa,.*":
     description: Linux Automation GmbH
+  "^luckfox,.*":
+    description: Shenzhen Luckfox Technology Co., Ltd.
   "^m5stack,.*":
     description: M5Stack
   "^macnica,.*":
-- 
2.39.5

[PATCH v4 2/3] dt-bindings: arm: rockchip: Add Luckfox Omni3576 and Core3576 bindings

[John Clark]

This patch adds device tree binding support for Luckfox Core3576 Module
based boards, specifically the Luckfox Omni3576, with compatibility for the
Rockchip RK3576 SoC.

Signed-off-by: John Clark <inindev@gmail.com>
---
 Documentation/devicetree/bindings/arm/rockchip.yaml | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml
index 455fbb290b77..92f494bae3bf 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.yaml
+++ b/Documentation/devicetree/bindings/arm/rockchip.yaml
@@ -715,6 +715,13 @@ properties:
           - const: lckfb,tspi-rk3566
           - const: rockchip,rk3566
 
+      - description: Luckfox Core3576 Module based boards
+        items:
+          - enum:
+              - luckfox,omni3576
+          - const: luckfox,core3576
+          - const: rockchip,rk3576
+
       - description: Lunzn FastRhino R66S / R68S
         items:
           - enum:
-- 
2.39.5

[PATCH v4 3/3] arm64: dts: rockchip: Add Luckfox Omni3576 Board support

[John Clark]

Add device tree for the Luckfox Omni3576 Carrier Board with Core3576
Module, powered by the Rockchip RK3576 SoC with four Cortex-A72 cores,
four Cortex-A53 cores, and a Mali-G52 MC3 GPU. This initial
implementation enables essential functionality for booting Linux and
basic connectivity.

Supported and tested features:
 - UART for serial console
 - SD card for storage
 - PCIe with NVMe SSD (detected, mounted, and fully functional)
 - USB 2.0 host ports
 - RK806 PMIC for power management
 - RTC with timekeeping and wake-up
 - GPIO-controlled LED with heartbeat trigger
 - eMMC (enabled, not populated on tested board)

The device tree provides a foundation for further peripheral support, such
as WiFi, MIPI-DSI, HDMI, and Ethernet, in future updates.

Tested on Linux 6.15-rc4

Signed-off-by: John Clark <inindev@gmail.com>
---
 arch/arm64/boot/dts/rockchip/Makefile         |   1 +
 .../dts/rockchip/rk3576-luckfox-core3576.dtsi | 683 ++++++++++++++++++
 .../dts/rockchip/rk3576-luckfox-omni3576.dts  |  53 ++
 3 files changed, 737 insertions(+)
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3576-luckfox-core3576.dtsi
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3576-luckfox-omni3576.dts

diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index 7948522cb225..22d74367b7e6 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -136,6 +136,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-wolfvision-pf5-display-vz.dtbo
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-wolfvision-pf5-io-expander.dtbo
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3576-armsom-sige5.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3576-evb1-v10.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3576-luckfox-omni3576.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3576-roc-pc.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3576-rock-4d.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3582-radxa-e52c.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3576-luckfox-core3576.dtsi b/arch/arm64/boot/dts/rockchip/rk3576-luckfox-core3576.dtsi
new file mode 100644
index 000000000000..9f0fa4427348
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3576-luckfox-core3576.dtsi
@@ -0,0 +1,683 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2024 Rockchip Electronics Co., Ltd.
+ *
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
+#include "rk3576.dtsi"
+
+/ {
+	model = "Luckfox Core3576 Module";
+	compatible = "luckfox,core3576","rockchip,rk3576";
+
+	chosen {
+		stdout-path = "serial0:1500000n8";
+	};
+
+	hdmi-con {
+		compatible = "hdmi-connector";
+		hdmi-pwr-supply = <&vcc_5v0_hdmi>;
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
+	vcc_5v0_dcin: regulator-vcc-5v0-dcin {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-name = "vcc_5v0_dcin";
+	};
+
+	vcc_1v1_nldo_s3: regulator-vcc-1v1-nldo-s3 {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1100000>;
+		regulator-name = "vcc_1v1_nldo_s3";
+		vin-supply = <&vcc_5v0_sys>;
+	};
+
+	vcc_2v0_pldo_s3: regulator-vcc-2v0-pldo-s3 {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <2000000>;
+		regulator-max-microvolt = <2000000>;
+		regulator-name = "vcc_2v0_pldo_s3";
+		vin-supply = <&vcc_5v0_sys>;
+	};
+
+	vcc_3v3_pcie: regulator-vcc-3v3-pcie {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpios = <&gpio4 RK_PA0 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pcie_pwr_en>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "vcc_3v3_pcie";
+		startup-delay-us = <1000>;
+		vin-supply = <&vcc_5v0_sys>;
+	};
+
+	vcc_3v3_rtc_s5: regulator-vcc-3v3-rtc-s5 {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "vcc_3v3_rtc_s5";
+		vin-supply = <&vcc_5v0_sys>;
+	};
+
+	vbus_5v0_typec: regulator-vbus-5v0-typec {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpios = <&gpio3 RK_PD5 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb_otg0_pwr_en>;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-name = "vbus5v0_typec";
+		vin-supply = <&vcc_5v0_device>;
+	};
+
+	vcc_5v0_device: regulator-vcc-5v0-device {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-name = "vcc_5v0_device";
+		vin-supply = <&vcc_5v0_dcin>;
+	};
+
+	vcc_5v0_hdmi: regulator-vcc-5v0-hdmi {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpios = <&gpio4 RK_PC6 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&hdmi_con_en>;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-name = "vcc_5v0_hdmi";
+		vin-supply = <&vcc_5v0_sys>;
+	};
+
+	vcc_5v0_host: regulator-vcc-5v0-host {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpios = <&gpio0 RK_PC7 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb_host_pwr_en>;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-name = "vcc_5v0_host";
+		vin-supply = <&vcc_5v0_device>;
+	};
+
+	vcc_5v0_sys: regulator-vcc-5v0-sys {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-name = "vcc_5v0_sys";
+		vin-supply = <&vcc_5v0_dcin>;
+	};
+};
+
+&combphy0_ps {
+	status = "okay";
+};
+
+&combphy1_psu {
+	status = "okay";
+};
+
+&cpu_l0 {
+	cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&cpu_l1 {
+	cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&cpu_l2 {
+	cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&cpu_l3 {
+	cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&cpu_b0 {
+	cpu-supply = <&vdd_cpu_big_s0>;
+};
+
+&cpu_b1 {
+	cpu-supply = <&vdd_cpu_big_s0>;
+};
+
+&cpu_b2 {
+	cpu-supply = <&vdd_cpu_big_s0>;
+};
+
+&cpu_b3 {
+	cpu-supply = <&vdd_cpu_big_s0>;
+};
+
+&gpu {
+	mali-supply = <&vdd_gpu_s0>;
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_in {
+	hdmi_in_vp0: endpoint {
+		remote-endpoint = <&vp0_out_hdmi>;
+	};
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&hdptxphy {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+
+	pmic@23 {
+		compatible = "rockchip,rk806";
+		reg = <0x23>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		interrupt-parent = <&gpio0>;
+		interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_pins>, <&rk806_dvs1_null>,
+			    <&rk806_dvs2_null>, <&rk806_dvs3_null>;
+		system-power-controller;
+
+		vcc1-supply = <&vcc_5v0_sys>;
+		vcc2-supply = <&vcc_5v0_sys>;
+		vcc3-supply = <&vcc_5v0_sys>;
+		vcc4-supply = <&vcc_5v0_sys>;
+		vcc5-supply = <&vcc_5v0_sys>;
+		vcc6-supply = <&vcc_5v0_sys>;
+		vcc7-supply = <&vcc_5v0_sys>;
+		vcc8-supply = <&vcc_5v0_sys>;
+		vcc9-supply = <&vcc_5v0_sys>;
+		vcc10-supply = <&vcc_5v0_sys>;
+		vcc11-supply = <&vcc_2v0_pldo_s3>;
+		vcc12-supply = <&vcc_5v0_sys>;
+		vcc13-supply = <&vcc_1v1_nldo_s3>;
+		vcc14-supply = <&vcc_1v1_nldo_s3>;
+		vcca-supply = <&vcc_5v0_sys>;
+
+		rk806_dvs1_null: dvs1-null-pins {
+			pins = "gpio_pwrctrl2";
+			function = "pin_fun0";
+		};
+
+		rk806_dvs2_null: dvs2-null-pins {
+			pins = "gpio_pwrctrl2";
+			function = "pin_fun0";
+		};
+
+		rk806_dvs3_null: dvs3-null-pins {
+			pins = "gpio_pwrctrl3";
+			function = "pin_fun0";
+		};
+
+		rk806_dvs1_slp: dvs1-slp-pins {
+			pins = "gpio_pwrctrl1";
+			function = "pin_fun1";
+		};
+
+		rk806_dvs1_pwrdn: dvs1-pwrdn-pins {
+			pins = "gpio_pwrctrl1";
+			function = "pin_fun2";
+		};
+
+		rk806_dvs1_rst: dvs1-rst-pins {
+			pins = "gpio_pwrctrl1";
+			function = "pin_fun3";
+		};
+
+		rk806_dvs2_slp: dvs2-slp-pins {
+			pins = "gpio_pwrctrl2";
+			function = "pin_fun1";
+		};
+
+		rk806_dvs2_pwrdn: dvs2-pwrdn-pins {
+			pins = "gpio_pwrctrl2";
+			function = "pin_fun2";
+		};
+
+		rk806_dvs2_rst: dvs2-rst-pins {
+			pins = "gpio_pwrctrl2";
+			function = "pin_fun3";
+		};
+
+		rk806_dvs2_dvs: dvs2-dvs-pins {
+			pins = "gpio_pwrctrl2";
+			function = "pin_fun4";
+		};
+
+		rk806_dvs2_gpio: dvs2-gpio-pins {
+			pins = "gpio_pwrctrl2";
+			function = "pin_fun5";
+		};
+
+
+		rk806_dvs3_slp: dvs3-slp-pins {
+			pins = "gpio_pwrctrl3";
+			function = "pin_fun1";
+		};
+
+		rk806_dvs3_pwrdn: dvs3-pwrdn-pins {
+			pins = "gpio_pwrctrl3";
+			function = "pin_fun2";
+		};
+
+		rk806_dvs3_rst: dvs3-rst-pins {
+			pins = "gpio_pwrctrl3";
+			function = "pin_fun3";
+		};
+
+		rk806_dvs3_dvs: dvs3-dvs-pins {
+			pins = "gpio_pwrctrl3";
+			function = "pin_fun4";
+		};
+
+		rk806_dvs3_gpio: dvs3-gpio-pins {
+			pins = "gpio_pwrctrl3";
+			function = "pin_fun5";
+		};
+
+		regulators {
+			vdd_cpu_big_s0: dcdc-reg1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <550000>;
+				regulator-max-microvolt = <950000>;
+				regulator-ramp-delay = <12500>;
+				regulator-name = "vdd_cpu_big_s0";
+				regulator-enable-ramp-delay = <400>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_npu_s0: dcdc-reg2 {
+				regulator-boot-on;
+				regulator-min-microvolt = <550000>;
+				regulator-max-microvolt = <950000>;
+				regulator-ramp-delay = <12500>;
+				regulator-name = "vdd_npu_s0";
+				regulator-enable-ramp-delay = <400>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_cpu_lit_s0: dcdc-reg3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <550000>;
+				regulator-max-microvolt = <950000>;
+				regulator-ramp-delay = <12500>;
+				regulator-name = "vdd_cpu_lit_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-suspend-microvolt = <750000>;
+				};
+			};
+
+			vcc_3v3_s3: dcdc-reg4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc_3v3_s3";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vdd_gpu_s0: dcdc-reg5 {
+				regulator-boot-on;
+				regulator-min-microvolt = <550000>;
+				regulator-max-microvolt = <900000>;
+				regulator-ramp-delay = <12500>;
+				regulator-name = "vdd_gpu_s0";
+				regulator-enable-ramp-delay = <400>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-suspend-microvolt = <850000>;
+				};
+			};
+
+			vddq_ddr_s0: dcdc-reg6 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vddq_ddr_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_logic_s0: dcdc-reg7 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <550000>;
+				regulator-max-microvolt = <800000>;
+				regulator-name = "vdd_logic_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_1v8_s3: dcdc-reg8 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc_1v8_s3";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vdd2_ddr_s3: dcdc-reg9 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vdd2_ddr_s3";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vdd_ddr_s0: dcdc-reg10 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <550000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-name = "vdd_ddr_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcca_1v8_s0: pldo-reg1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcca_1v8_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcca1v8_pldo2_s0: pldo-reg2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcca1v8_pldo2_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda_1v2_s0: pldo-reg3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-name = "vdda_1v2_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcca_3v3_s0: pldo-reg4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcca_3v3_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vccio_sd_s0: pldo-reg5 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vccio_sd_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcca1v8_pldo6_s3: pldo-reg6 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcca1v8_pldo6_s3";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vdd_0v75_s3: nldo-reg1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <750000>;
+				regulator-name = "vdd_0v75_s3";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <750000>;
+				};
+			};
+
+			vdda_ddr_pll_s0: nldo-reg2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-name = "vdda_ddr_pll_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda0v75_hdmi_s0: nldo-reg3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <837500>;
+				regulator-max-microvolt = <837500>;
+				regulator-name = "vdda0v75_hdmi_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda_0v85_s0: nldo-reg4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-name = "vdda_0v85_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda_0v75_s0: nldo-reg5 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <750000>;
+				regulator-name = "vdda_0v75_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+		};
+	};
+};
+
+&i2c2 {
+	status = "okay";
+
+	hym8563: rtc@51 {
+		compatible = "haoyu,hym8563";
+		reg = <0x51>;
+		#clock-cells = <0>;
+		clock-output-names = "hym8563";
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PA5 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&hym8563_int>;
+		wakeup-source;
+	};
+};
+
+&pcie0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie_reset>;
+	reset-gpios = <&gpio2 RK_PB1 GPIO_ACTIVE_HIGH>;
+	vpcie3v3-supply = <&vcc_3v3_pcie>;
+	status = "okay";
+};
+
+&pinctrl {
+	hdmi {
+		hdmi_con_en: hdmi-con-en {
+			rockchip,pins = <4 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	hym8563 {
+		hym8563_int: hym8563-int {
+			rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	pcie {
+		pcie_pwr_en: pcie-pwr-en {
+			rockchip,pins = <4 RK_PA0 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+
+		pcie_reset: pcie-reset {
+			rockchip,pins = <2 RK_PB1 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	usb {
+		usb_host_pwr_en: usb-host-pwr-en {
+			rockchip,pins = <1 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		usb_otg0_pwr_en: usb-otg0-pwr-en {
+			rockchip,pins = <3 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		usbc0_int: usbc0-int {
+			rockchip,pins = <3 RK_PD4 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+};
+
+&rng {
+	status = "okay";
+};
+
+&saradc {
+	vref-supply = <&vcca_1v8_s0>;
+	status = "okay";
+};
+
+&sdhci {
+	bus-width = <8>;
+	full-pwr-cycle-in-suspend;
+	max-frequency = <200000000>;
+	mmc-hs400-1_8v;
+	mmc-hs400-enhanced-strobe;
+	no-sd;
+	no-sdio;
+	non-removable;
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4m1_xfer &uart4m1_ctsn>;
+	status = "okay";
+};
+
+&u2phy1 {
+	status = "okay";
+};
+
+&u2phy1_otg {
+	phy-supply = <&vcc_5v0_host>;
+	status = "okay";
+};
+
+&usb_drd1_dwc3 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&vop {
+	status = "okay";
+};
+
+&vop_mmu {
+	status = "okay";
+};
+
+&vp0 {
+	vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
+		reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+		remote-endpoint = <&hdmi_in_vp0>;
+	};
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3576-luckfox-omni3576.dts b/arch/arm64/boot/dts/rockchip/rk3576-luckfox-omni3576.dts
new file mode 100644
index 000000000000..3361b9e9a01c
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3576-luckfox-omni3576.dts
@@ -0,0 +1,53 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2024 Rockchip Electronics Co., Ltd.
+ *
+ */
+
+/dts-v1/;
+
+#include "rk3576-luckfox-core3576.dtsi"
+
+/ {
+	model = "Luckfox Omni3576 Carrier Board";
+	compatible = "luckfox,omni3576", "luckfox,core3576", "rockchip,rk3576";
+
+	aliases {
+		mmc0 = &sdhci;
+		mmc1 = &sdmmc;
+	};
+
+	leds: leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_green_pin>;
+
+		green_led: green-led {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_HEARTBEAT;
+			gpios = <&gpio1 RK_PD5 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&pinctrl {
+	leds {
+		led_green_pin: led-green-pin {
+			rockchip,pins = <1 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+	disable-wp;
+	max-frequency = <200000000>;
+	no-sdio;
+	sd-uhs-sdr104;
+	vmmc-supply = <&vcc_3v3_s3>;
+	vqmmc-supply = <&vccio_sd_s0>;
+	status = "okay";
+};
-- 
2.39.5

Re: [PATCH v4 1/3] dt-bindings: vendor-prefixes: Add luckfox prefix

[Krzysztof Kozlowski]

On 08/05/2025 21:05, John Clark wrote:
> Add vendor prefix for Shenzhen Luckfox Technology Co., Ltd., which
> produces development boards like the Luckfox Omni3576.
> 
> Signed-off-by: John Clark <inindev@gmail.com>
> Acked-by: Conor Dooley <conor.dooley@microchip.com>
You already got this feedback and still did not respond to it.

<form letter>
This is a friendly reminder during the review process.

It looks like you received a tag and forgot to add it.

If you do not know the process, here is a short explanation:
Please add Acked-by/Reviewed-by/Tested-by tags when posting new versions
of patchset, under or above your Signed-off-by tag, unless patch changed
significantly (e.g. new properties added to the DT bindings). Tag is
"received", when provided in a message replied to you on the mailing
list. Tools like b4 can help here. However, there's no need to repost
patches *only* to add the tags. The upstream maintainer will do that for
tags received on the version they apply.

Please read:
https://elixir.bootlin.com/linux/v6.12-rc3/source/Documentation/process/submitting-patches.rst#L577

If a tag was not added on purpose, please state why and what changed.
</form letter>

Best regards,
Krzysztof