[PATCH v9 0/9] Add STM32MP25 PCIe drivers

[PATCH v9 0/9] Add STM32MP25 PCIe drivers

[Christian Bruel]

Changes in v9:
   - Describe atu and dbi2 shadowed registers in pcie_ep node
   Address RC and EP drivers comments from Manivanna:
   - Use dev_error_probe() for pm_runtime_enable() calls
   - Reword Kconfig help message
   - Move pm_runtime_get_noresume() before devm_pm_runtime_enable()

Changes in v8:
   - Whitespace in comment
   
Changes in v7:
   - Use device_init_wakeup to enable wakeup
   - Fix comments (Bjorn)

Changes in v6:
   - Call device_wakeup_enable() to fix WAKE# wakeup.
   Address comments from Manivanna:
   - Fix/Add Comments
   - Fix DT indents
   - Remove dw_pcie_ep_linkup() in EP start link
   - Add PCIE_T_PVPERL_MS delay in RC PERST# deassert
   
Changes in v5:
   Address driver comments from Manivanna:
   - Use dw_pcie_{suspend/resume}_noirq instead of private ones.
   - Move dw_pcie_host_init() to probe
   - Add stm32_remove_pcie_port cleanup function
   - Use of_node_put in stm32_pcie_parse_port
   - Remove wakeup-source property
   - Use generic dev_pm_set_dedicated_wake_irq to support wake# irq
   
Changes in v4:
   Address bindings comments Rob Herring
   - Remove phy property form common yaml
   - Remove phy-name property
   - Move wake_gpio and reset_gpio to the host root port
   
Changes in v3:
   Address comments from Manivanna, Rob and Bjorn:
   - Move host wakeup helper to dwc core (Mani)
   - Drop num-lanes=<1> from bindings (Rob)
   - Fix PCI address of I/O region (Mani)
   - Moved PHY to a RC rootport subsection (Bjorn, Mani)
   - Replaced dma-limit quirk by dma-ranges property (Bjorn)
   - Moved out perst assert/deassert from start/stop link (Mani)
   - Drop link_up test optim (Mani)
   - DT and comments rephrasing (Bjorn)
   - Add dts entries now that the combophy entries has landed
   - Drop delaying Configuration Requests

Changes in v2:
   - Fix st,stm32-pcie-common.yaml dt_binding_check	

Changes in v1:
   Address comments from Rob Herring and Bjorn Helgaas:
   - Drop st,limit-mrrs and st,max-payload-size from this patchset
   - Remove single reset and clocks binding names and misc yaml cleanups
   - Split RC/EP common bindings to a separate schema file
   - Use correct PCIE_T_PERST_CLK_US and PCIE_T_RRS_READY_MS defines
   - Use .remove instead of .remove_new
   - Fix bar reset sequence in EP driver
   - Use cleanup blocks for error handling
   - Cosmetic fixes

Christian Bruel (9):
  dt-bindings: PCI: Add STM32MP25 PCIe Root Complex bindings
  PCI: stm32: Add PCIe host support for STM32MP25
  dt-bindings: PCI: Add STM32MP25 PCIe Endpoint bindings
  PCI: stm32: Add PCIe Endpoint support for STM32MP25
  MAINTAINERS: add entry for ST STM32MP25 PCIe drivers
  arm64: dts: st: add PCIe pinctrl entries in stm32mp25-pinctrl.dtsi
  arm64: dts: st: Add PCIe Root Complex mode on stm32mp251
  arm64: dts: st: Add PCIe Endpoint mode on stm32mp251
  arm64: dts: st: Enable PCIe on the stm32mp257f-ev1 board

 .../bindings/pci/st,stm32-pcie-common.yaml    |  33 ++
 .../bindings/pci/st,stm32-pcie-ep.yaml        |  67 +++
 .../bindings/pci/st,stm32-pcie-host.yaml      | 112 +++++
 MAINTAINERS                                   |   7 +
 arch/arm64/boot/dts/st/stm32mp25-pinctrl.dtsi |  20 +
 arch/arm64/boot/dts/st/stm32mp251.dtsi        |  57 +++
 arch/arm64/boot/dts/st/stm32mp257f-ev1.dts    |  21 +
 drivers/pci/controller/dwc/Kconfig            |  24 +
 drivers/pci/controller/dwc/Makefile           |   2 +
 drivers/pci/controller/dwc/pcie-stm32-ep.c    | 411 ++++++++++++++++++
 drivers/pci/controller/dwc/pcie-stm32.c       | 364 ++++++++++++++++
 drivers/pci/controller/dwc/pcie-stm32.h       |  16 +
 12 files changed, 1134 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pci/st,stm32-pcie-common.yaml
 create mode 100644 Documentation/devicetree/bindings/pci/st,stm32-pcie-ep.yaml
 create mode 100644 Documentation/devicetree/bindings/pci/st,stm32-pcie-host.yaml
 create mode 100644 drivers/pci/controller/dwc/pcie-stm32-ep.c
 create mode 100644 drivers/pci/controller/dwc/pcie-stm32.c
 create mode 100644 drivers/pci/controller/dwc/pcie-stm32.h

-- 
2.34.1

[PATCH v9 1/9] dt-bindings: PCI: Add STM32MP25 PCIe Root Complex bindings

[Christian Bruel]

Document the bindings for STM32MP25 PCIe Controller configured in
root complex mode with one root port.

Supports 4 INTx and MSI interrupts from the ARM GICv2m controller.

STM32 PCIe may be in a power domain which is the case for the STM32MP25
based boards.

Supports WAKE# from wake-gpios

Signed-off-by: Christian Bruel <christian.bruel@foss.st.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---
 .../bindings/pci/st,stm32-pcie-common.yaml    |  33 ++++++
 .../bindings/pci/st,stm32-pcie-host.yaml      | 112 ++++++++++++++++++
 2 files changed, 145 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pci/st,stm32-pcie-common.yaml
 create mode 100644 Documentation/devicetree/bindings/pci/st,stm32-pcie-host.yaml

diff --git a/Documentation/devicetree/bindings/pci/st,stm32-pcie-common.yaml b/Documentation/devicetree/bindings/pci/st,stm32-pcie-common.yaml
new file mode 100644
index 000000000000..5adbff259204
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/st,stm32-pcie-common.yaml
@@ -0,0 +1,33 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pci/st,stm32-pcie-common.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: STM32MP25 PCIe RC/EP controller
+
+maintainers:
+  - Christian Bruel <christian.bruel@foss.st.com>
+
+description:
+  STM32MP25 PCIe RC/EP common properties
+
+properties:
+  clocks:
+    maxItems: 1
+    description: PCIe system clock
+
+  resets:
+    maxItems: 1
+
+  power-domains:
+    maxItems: 1
+
+  access-controllers:
+    maxItems: 1
+
+required:
+  - clocks
+  - resets
+
+additionalProperties: true
diff --git a/Documentation/devicetree/bindings/pci/st,stm32-pcie-host.yaml b/Documentation/devicetree/bindings/pci/st,stm32-pcie-host.yaml
new file mode 100644
index 000000000000..443bfe2cdc98
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/st,stm32-pcie-host.yaml
@@ -0,0 +1,112 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pci/st,stm32-pcie-host.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: STMicroelectronics STM32MP25 PCIe Root Complex
+
+maintainers:
+  - Christian Bruel <christian.bruel@foss.st.com>
+
+description:
+  PCIe root complex controller based on the Synopsys DesignWare PCIe core.
+
+allOf:
+  - $ref: /schemas/pci/snps,dw-pcie.yaml#
+  - $ref: /schemas/pci/st,stm32-pcie-common.yaml#
+
+properties:
+  compatible:
+    const: st,stm32mp25-pcie-rc
+
+  reg:
+    items:
+      - description: Data Bus Interface (DBI) registers.
+      - description: PCIe configuration registers.
+
+  reg-names:
+    items:
+      - const: dbi
+      - const: config
+
+  msi-parent:
+    maxItems: 1
+
+patternProperties:
+  '^pcie@[0-2],0$':
+    type: object
+    $ref: /schemas/pci/pci-pci-bridge.yaml#
+
+    properties:
+      reg:
+        maxItems: 1
+
+      phys:
+        maxItems: 1
+
+      reset-gpios:
+        description: GPIO controlled connection to PERST# signal
+        maxItems: 1
+
+      wake-gpios:
+        description: GPIO used as WAKE# input signal
+        maxItems: 1
+
+    required:
+      - phys
+      - ranges
+
+    unevaluatedProperties: false
+
+required:
+  - interrupt-map
+  - interrupt-map-mask
+  - ranges
+  - dma-ranges
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/st,stm32mp25-rcc.h>
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/phy/phy.h>
+    #include <dt-bindings/reset/st,stm32mp25-rcc.h>
+
+    pcie@48400000 {
+        compatible = "st,stm32mp25-pcie-rc";
+        device_type = "pci";
+        reg = <0x48400000 0x400000>,
+              <0x10000000 0x10000>;
+        reg-names = "dbi", "config";
+        #interrupt-cells = <1>;
+        interrupt-map-mask = <0 0 0 7>;
+        interrupt-map = <0 0 0 1 &intc 0 0 GIC_SPI 264 IRQ_TYPE_LEVEL_HIGH>,
+                        <0 0 0 2 &intc 0 0 GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>,
+                        <0 0 0 3 &intc 0 0 GIC_SPI 266 IRQ_TYPE_LEVEL_HIGH>,
+                        <0 0 0 4 &intc 0 0 GIC_SPI 267 IRQ_TYPE_LEVEL_HIGH>;
+        #address-cells = <3>;
+        #size-cells = <2>;
+        ranges = <0x01000000 0x0 0x00000000 0x10010000 0x0 0x10000>,
+                 <0x02000000 0x0 0x10020000 0x10020000 0x0 0x7fe0000>,
+                 <0x42000000 0x0 0x18000000 0x18000000 0x0 0x8000000>;
+        dma-ranges = <0x42000000 0x0 0x80000000 0x80000000 0x0 0x80000000>;
+        clocks = <&rcc CK_BUS_PCIE>;
+        resets = <&rcc PCIE_R>;
+        msi-parent = <&v2m0>;
+        access-controllers = <&rifsc 68>;
+        power-domains = <&CLUSTER_PD>;
+
+        pcie@0,0 {
+            device_type = "pci";
+            reg = <0x0 0x0 0x0 0x0 0x0>;
+            phys = <&combophy PHY_TYPE_PCIE>;
+            wake-gpios = <&gpioh 5 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+            reset-gpios = <&gpioj 8 GPIO_ACTIVE_LOW>;
+            #address-cells = <3>;
+            #size-cells = <2>;
+            ranges;
+        };
+    };
-- 
2.34.1

[PATCH v9 2/9] PCI: stm32: Add PCIe host support for STM32MP25

[Christian Bruel]

Add driver for the STM32MP25 SoC PCIe Gen1 2.5 GT/s and Gen2 5GT/s
controller based on the DesignWare PCIe core.

Supports MSI via GICv2m, Single Virtual Channel, Single Function

Supports WAKE# GPIO.

Signed-off-by: Christian Bruel <christian.bruel@foss.st.com>
---
 drivers/pci/controller/dwc/Kconfig      |  12 +
 drivers/pci/controller/dwc/Makefile     |   1 +
 drivers/pci/controller/dwc/pcie-stm32.c | 364 ++++++++++++++++++++++++
 drivers/pci/controller/dwc/pcie-stm32.h |  15 +
 4 files changed, 392 insertions(+)
 create mode 100644 drivers/pci/controller/dwc/pcie-stm32.c
 create mode 100644 drivers/pci/controller/dwc/pcie-stm32.h

diff --git a/drivers/pci/controller/dwc/Kconfig b/drivers/pci/controller/dwc/Kconfig
index d9f0386396ed..387151f25f5f 100644
--- a/drivers/pci/controller/dwc/Kconfig
+++ b/drivers/pci/controller/dwc/Kconfig
@@ -410,6 +410,18 @@ config PCIE_SPEAR13XX
 	help
 	  Say Y here if you want PCIe support on SPEAr13XX SoCs.
 
+config PCIE_STM32_HOST
+	tristate "STMicroelectronics STM32MP25 PCIe Controller (host mode)"
+	depends on ARCH_STM32 || COMPILE_TEST
+	depends on PCI_MSI
+	select PCIE_DW_HOST
+	help
+	  Enables Root Complex (RC) support for the DesignWare core based PCIe
+	  controller found in STM32MP25 SoC.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called pcie-stm32.
+
 config PCI_DRA7XX
 	tristate
 
diff --git a/drivers/pci/controller/dwc/Makefile b/drivers/pci/controller/dwc/Makefile
index 908cb7f345db..9d3b43504725 100644
--- a/drivers/pci/controller/dwc/Makefile
+++ b/drivers/pci/controller/dwc/Makefile
@@ -30,6 +30,7 @@ obj-$(CONFIG_PCIE_UNIPHIER) += pcie-uniphier.o
 obj-$(CONFIG_PCIE_UNIPHIER_EP) += pcie-uniphier-ep.o
 obj-$(CONFIG_PCIE_VISCONTI_HOST) += pcie-visconti.o
 obj-$(CONFIG_PCIE_RCAR_GEN4) += pcie-rcar-gen4.o
+obj-$(CONFIG_PCIE_STM32_HOST) += pcie-stm32.o
 
 # The following drivers are for devices that use the generic ACPI
 # pci_root.c driver but don't support standard ECAM config access.
diff --git a/drivers/pci/controller/dwc/pcie-stm32.c b/drivers/pci/controller/dwc/pcie-stm32.c
new file mode 100644
index 000000000000..f08c81a5797f
--- /dev/null
+++ b/drivers/pci/controller/dwc/pcie-stm32.c
@@ -0,0 +1,364 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * STMicroelectronics STM32MP25 PCIe root complex driver.
+ *
+ * Copyright (C) 2025 STMicroelectronics
+ * Author: Christian Bruel <christian.bruel@foss.st.com>
+ */
+
+#include <linux/clk.h>
+#include <linux/mfd/syscon.h>
+#include <linux/of_platform.h>
+#include <linux/phy/phy.h>
+#include <linux/pinctrl/devinfo.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/pm_wakeirq.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+#include "pcie-designware.h"
+#include "pcie-stm32.h"
+#include "../../pci.h"
+
+struct stm32_pcie {
+	struct dw_pcie pci;
+	struct regmap *regmap;
+	struct reset_control *rst;
+	struct phy *phy;
+	struct clk *clk;
+	struct gpio_desc *perst_gpio;
+	struct gpio_desc *wake_gpio;
+};
+
+static void stm32_pcie_deassert_perst(struct stm32_pcie *stm32_pcie)
+{
+	/* Delay PERST# de-assertion until the power stabilizes */
+	msleep(PCIE_T_PVPERL_MS);
+
+	gpiod_set_value(stm32_pcie->perst_gpio, 0);
+
+	/* Wait for the REFCLK to stabilize */
+	if (stm32_pcie->perst_gpio)
+		msleep(PCIE_T_RRS_READY_MS);
+}
+
+static void stm32_pcie_assert_perst(struct stm32_pcie *stm32_pcie)
+{
+	gpiod_set_value(stm32_pcie->perst_gpio, 1);
+}
+
+static int stm32_pcie_start_link(struct dw_pcie *pci)
+{
+	struct stm32_pcie *stm32_pcie = to_stm32_pcie(pci);
+
+	return regmap_update_bits(stm32_pcie->regmap, SYSCFG_PCIECR,
+				  STM32MP25_PCIECR_LTSSM_EN,
+				  STM32MP25_PCIECR_LTSSM_EN);
+}
+
+static void stm32_pcie_stop_link(struct dw_pcie *pci)
+{
+	struct stm32_pcie *stm32_pcie = to_stm32_pcie(pci);
+
+	regmap_update_bits(stm32_pcie->regmap, SYSCFG_PCIECR,
+			   STM32MP25_PCIECR_LTSSM_EN, 0);
+}
+
+static int stm32_pcie_suspend_noirq(struct device *dev)
+{
+	struct stm32_pcie *stm32_pcie = dev_get_drvdata(dev);
+	int ret;
+
+	ret = dw_pcie_suspend_noirq(&stm32_pcie->pci);
+	if (ret)
+		return ret;
+
+	stm32_pcie_assert_perst(stm32_pcie);
+
+	clk_disable_unprepare(stm32_pcie->clk);
+
+	if (!device_wakeup_path(dev))
+		phy_exit(stm32_pcie->phy);
+
+	return pinctrl_pm_select_sleep_state(dev);
+}
+
+static int stm32_pcie_resume_noirq(struct device *dev)
+{
+	struct stm32_pcie *stm32_pcie = dev_get_drvdata(dev);
+	int ret;
+
+	/*
+	 * The core clock is gated with CLKREQ# from the COMBOPHY REFCLK,
+	 * thus if no device is present, must force it low with an init pinmux
+	 * to be able to access the DBI registers.
+	 */
+	if (!IS_ERR(dev->pins->init_state))
+		ret = pinctrl_select_state(dev->pins->p, dev->pins->init_state);
+	else
+		ret = pinctrl_pm_select_default_state(dev);
+
+	if (ret) {
+		dev_err(dev, "Failed to activate pinctrl pm state: %d\n", ret);
+		return ret;
+	}
+
+	if (!device_wakeup_path(dev)) {
+		ret = phy_init(stm32_pcie->phy);
+		if (ret) {
+			pinctrl_pm_select_default_state(dev);
+			return ret;
+		}
+	}
+
+	ret = clk_prepare_enable(stm32_pcie->clk);
+	if (ret)
+		goto err_phy_exit;
+
+	stm32_pcie_deassert_perst(stm32_pcie);
+
+	ret = dw_pcie_resume_noirq(&stm32_pcie->pci);
+	if (ret)
+		goto err_disable_clk;
+
+	pinctrl_pm_select_default_state(dev);
+
+	return 0;
+
+err_disable_clk:
+	stm32_pcie_assert_perst(stm32_pcie);
+	clk_disable_unprepare(stm32_pcie->clk);
+
+err_phy_exit:
+	phy_exit(stm32_pcie->phy);
+	pinctrl_pm_select_default_state(dev);
+
+	return ret;
+}
+
+static const struct dev_pm_ops stm32_pcie_pm_ops = {
+	NOIRQ_SYSTEM_SLEEP_PM_OPS(stm32_pcie_suspend_noirq,
+				  stm32_pcie_resume_noirq)
+};
+
+static const struct dw_pcie_host_ops stm32_pcie_host_ops = {
+};
+
+static const struct dw_pcie_ops dw_pcie_ops = {
+	.start_link = stm32_pcie_start_link,
+	.stop_link = stm32_pcie_stop_link
+};
+
+static int stm32_add_pcie_port(struct stm32_pcie *stm32_pcie,
+			       struct platform_device *pdev)
+{
+	struct device *dev = stm32_pcie->pci.dev;
+	unsigned int wake_irq;
+	int ret;
+
+	/* Start to enable resources with PERST# asserted */
+
+	ret = phy_set_mode(stm32_pcie->phy, PHY_MODE_PCIE);
+	if (ret)
+		return ret;
+
+	ret = phy_init(stm32_pcie->phy);
+	if (ret)
+		return ret;
+
+	ret = regmap_update_bits(stm32_pcie->regmap, SYSCFG_PCIECR,
+				 STM32MP25_PCIECR_TYPE_MASK,
+				 STM32MP25_PCIECR_RC);
+	if (ret)
+		goto err_phy_exit;
+
+	stm32_pcie_deassert_perst(stm32_pcie);
+
+	if (stm32_pcie->wake_gpio) {
+		wake_irq = gpiod_to_irq(stm32_pcie->wake_gpio);
+		ret = dev_pm_set_dedicated_wake_irq(dev, wake_irq);
+		if (ret) {
+			dev_err(dev, "Failed to enable wakeup irq %d\n", ret);
+			goto err_assert_perst;
+		}
+		irq_set_irq_type(wake_irq, IRQ_TYPE_EDGE_FALLING);
+	}
+
+	return 0;
+
+err_assert_perst:
+	stm32_pcie_assert_perst(stm32_pcie);
+
+err_phy_exit:
+	phy_exit(stm32_pcie->phy);
+
+	return ret;
+}
+
+static void stm32_remove_pcie_port(struct stm32_pcie *stm32_pcie)
+{
+	stm32_pcie_assert_perst(stm32_pcie);
+
+	phy_exit(stm32_pcie->phy);
+}
+
+static int stm32_pcie_parse_port(struct stm32_pcie *stm32_pcie)
+{
+	struct device *dev = stm32_pcie->pci.dev;
+	struct device_node *root_port;
+
+	root_port = of_get_next_available_child(dev->of_node, NULL);
+
+	stm32_pcie->phy = devm_of_phy_get(dev, root_port, NULL);
+	if (IS_ERR(stm32_pcie->phy)) {
+		of_node_put(root_port);
+		return dev_err_probe(dev, PTR_ERR(stm32_pcie->phy),
+				     "Failed to get pcie-phy\n");
+	}
+
+	stm32_pcie->perst_gpio = devm_fwnode_gpiod_get(dev, of_fwnode_handle(root_port),
+						       "reset", GPIOD_OUT_HIGH, NULL);
+	if (IS_ERR(stm32_pcie->perst_gpio)) {
+		if (PTR_ERR(stm32_pcie->perst_gpio) != -ENOENT) {
+			of_node_put(root_port);
+			return dev_err_probe(dev, PTR_ERR(stm32_pcie->perst_gpio),
+					     "Failed to get reset GPIO\n");
+		}
+		stm32_pcie->perst_gpio = NULL;
+	}
+
+	stm32_pcie->wake_gpio = devm_fwnode_gpiod_get(dev, of_fwnode_handle(root_port),
+						      "wake", GPIOD_IN, NULL);
+
+	if (IS_ERR(stm32_pcie->wake_gpio)) {
+		if (PTR_ERR(stm32_pcie->wake_gpio) != -ENOENT) {
+			of_node_put(root_port);
+			return dev_err_probe(dev, PTR_ERR(stm32_pcie->wake_gpio),
+					     "Failed to get wake GPIO\n");
+		}
+		stm32_pcie->wake_gpio = NULL;
+	}
+
+	of_node_put(root_port);
+
+	return 0;
+}
+
+static int stm32_pcie_probe(struct platform_device *pdev)
+{
+	struct stm32_pcie *stm32_pcie;
+	struct device *dev = &pdev->dev;
+	int ret;
+
+	stm32_pcie = devm_kzalloc(dev, sizeof(*stm32_pcie), GFP_KERNEL);
+	if (!stm32_pcie)
+		return -ENOMEM;
+
+	stm32_pcie->pci.dev = dev;
+	stm32_pcie->pci.ops = &dw_pcie_ops;
+	stm32_pcie->pci.pp.ops = &stm32_pcie_host_ops;
+
+	stm32_pcie->regmap = syscon_regmap_lookup_by_compatible("st,stm32mp25-syscfg");
+	if (IS_ERR(stm32_pcie->regmap))
+		return dev_err_probe(dev, PTR_ERR(stm32_pcie->regmap),
+				     "No syscfg specified\n");
+
+	stm32_pcie->clk = devm_clk_get(dev, NULL);
+	if (IS_ERR(stm32_pcie->clk))
+		return dev_err_probe(dev, PTR_ERR(stm32_pcie->clk),
+				     "Failed to get PCIe clock source\n");
+
+	stm32_pcie->rst = devm_reset_control_get_exclusive(dev, NULL);
+	if (IS_ERR(stm32_pcie->rst))
+		return dev_err_probe(dev, PTR_ERR(stm32_pcie->rst),
+				     "Failed to get PCIe reset\n");
+
+	ret = stm32_pcie_parse_port(stm32_pcie);
+	if (ret)
+		return ret;
+
+	platform_set_drvdata(pdev, stm32_pcie);
+
+	ret = pm_runtime_set_active(dev);
+	if (ret < 0)
+		return dev_err_probe(dev, ret, "Failed to activate runtime PM\n");
+
+	pm_runtime_get_noresume(dev);
+
+	ret = devm_pm_runtime_enable(dev);
+	if (ret < 0)
+		return dev_err_probe(dev, ret, "Failed to enable runtime PM\n");
+
+	ret = stm32_add_pcie_port(stm32_pcie, pdev);
+	if (ret) {
+		pm_runtime_put_noidle(&pdev->dev);
+		return ret;
+	}
+
+	reset_control_assert(stm32_pcie->rst);
+	reset_control_deassert(stm32_pcie->rst);
+
+	ret = clk_prepare_enable(stm32_pcie->clk);
+	if (ret) {
+		dev_err(dev, "Core clock enable failed %d\n", ret);
+		goto err_remove_port;
+	}
+
+	ret = dw_pcie_host_init(&stm32_pcie->pci.pp);
+	if (ret)
+		goto err_disable_clk;
+
+	if (stm32_pcie->wake_gpio)
+		device_init_wakeup(dev, true);
+
+	return 0;
+
+err_disable_clk:
+	clk_disable_unprepare(stm32_pcie->clk);
+
+err_remove_port:
+	stm32_remove_pcie_port(stm32_pcie);
+	pm_runtime_put_noidle(&pdev->dev);
+
+	return ret;
+}
+
+static void stm32_pcie_remove(struct platform_device *pdev)
+{
+	struct stm32_pcie *stm32_pcie = platform_get_drvdata(pdev);
+	struct dw_pcie_rp *pp = &stm32_pcie->pci.pp;
+
+	if (stm32_pcie->wake_gpio)
+		device_init_wakeup(&pdev->dev, false);
+
+	dw_pcie_host_deinit(pp);
+
+	clk_disable_unprepare(stm32_pcie->clk);
+
+	stm32_remove_pcie_port(stm32_pcie);
+
+	pm_runtime_put_noidle(&pdev->dev);
+}
+
+static const struct of_device_id stm32_pcie_of_match[] = {
+	{ .compatible = "st,stm32mp25-pcie-rc" },
+	{},
+};
+
+static struct platform_driver stm32_pcie_driver = {
+	.probe = stm32_pcie_probe,
+	.remove = stm32_pcie_remove,
+	.driver = {
+		.name = "stm32-pcie",
+		.of_match_table = stm32_pcie_of_match,
+		.pm = &stm32_pcie_pm_ops,
+		.probe_type = PROBE_PREFER_ASYNCHRONOUS,
+	},
+};
+
+module_platform_driver(stm32_pcie_driver);
+
+MODULE_AUTHOR("Christian Bruel <christian.bruel@foss.st.com>");
+MODULE_DESCRIPTION("STM32MP25 PCIe Controller driver");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(of, stm32_pcie_of_match);
diff --git a/drivers/pci/controller/dwc/pcie-stm32.h b/drivers/pci/controller/dwc/pcie-stm32.h
new file mode 100644
index 000000000000..387112c4e42c
--- /dev/null
+++ b/drivers/pci/controller/dwc/pcie-stm32.h
@@ -0,0 +1,15 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * ST PCIe driver definitions for STM32-MP25 SoC
+ *
+ * Copyright (C) 2025 STMicroelectronics - All Rights Reserved
+ * Author: Christian Bruel <christian.bruel@foss.st.com>
+ */
+
+#define to_stm32_pcie(x)	dev_get_drvdata((x)->dev)
+
+#define STM32MP25_PCIECR_TYPE_MASK	GENMASK(11, 8)
+#define STM32MP25_PCIECR_LTSSM_EN	BIT(2)
+#define STM32MP25_PCIECR_RC		BIT(10)
+
+#define SYSCFG_PCIECR			0x6000
-- 
2.34.1

[PATCH v9 3/9] dt-bindings: PCI: Add STM32MP25 PCIe Endpoint bindings

[Christian Bruel]

STM32MP25 PCIe Controller is based on the DesignWare core configured as
end point mode from the SYSCFG register.

Signed-off-by: Christian Bruel <christian.bruel@foss.st.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---
 .../bindings/pci/st,stm32-pcie-ep.yaml        | 67 +++++++++++++++++++
 1 file changed, 67 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pci/st,stm32-pcie-ep.yaml

diff --git a/Documentation/devicetree/bindings/pci/st,stm32-pcie-ep.yaml b/Documentation/devicetree/bindings/pci/st,stm32-pcie-ep.yaml
new file mode 100644
index 000000000000..fc1bbe19e616
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/st,stm32-pcie-ep.yaml
@@ -0,0 +1,67 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pci/st,stm32-pcie-ep.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: STMicroelectronics STM32MP25 PCIe Endpoint
+
+maintainers:
+  - Christian Bruel <christian.bruel@foss.st.com>
+
+description:
+  PCIe endpoint controller based on the Synopsys DesignWare PCIe core.
+
+allOf:
+  - $ref: /schemas/pci/snps,dw-pcie-ep.yaml#
+  - $ref: /schemas/pci/st,stm32-pcie-common.yaml#
+
+properties:
+  compatible:
+    const: st,stm32mp25-pcie-ep
+
+  reg:
+    items:
+      - description: Data Bus Interface (DBI) registers.
+      - description: PCIe configuration registers.
+
+  reg-names:
+    items:
+      - const: dbi
+      - const: addr_space
+
+  reset-gpios:
+    description: GPIO controlled connection to PERST# signal
+    maxItems: 1
+
+  phys:
+    maxItems: 1
+
+required:
+  - phys
+  - reset-gpios
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/st,stm32mp25-rcc.h>
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/phy/phy.h>
+    #include <dt-bindings/reset/st,stm32mp25-rcc.h>
+
+    pcie-ep@48400000 {
+        compatible = "st,stm32mp25-pcie-ep";
+        reg = <0x48400000 0x400000>,
+              <0x10000000 0x8000000>;
+        reg-names = "dbi", "addr_space";
+        clocks = <&rcc CK_BUS_PCIE>;
+        phys = <&combophy PHY_TYPE_PCIE>;
+        resets = <&rcc PCIE_R>;
+        pinctrl-names = "default", "init";
+        pinctrl-0 = <&pcie_pins_a>;
+        pinctrl-1 = <&pcie_init_pins_a>;
+        reset-gpios = <&gpioj 8 GPIO_ACTIVE_LOW>;
+        access-controllers = <&rifsc 68>;
+        power-domains = <&CLUSTER_PD>;
+    };
-- 
2.34.1

[PATCH v9 4/9] PCI: stm32: Add PCIe Endpoint support for STM32MP25

[Christian Bruel]

Add driver to configure the STM32MP25 SoC PCIe Gen1 2.5GT/s or Gen2 5GT/s
controller based on the DesignWare PCIe core in endpoint mode.

Uses the common reference clock provided by the host.

The PCIe core_clk receives the pipe0_clk from the ComboPHY as input,
and the ComboPHY PLL must be locked for pipe0_clk to be ready.
Consequently, PCIe core registers cannot be accessed until the ComboPHY is
fully initialised and refclk is enabled and ready.

Signed-off-by: Christian Bruel <christian.bruel@foss.st.com>
---
 drivers/pci/controller/dwc/Kconfig         |  12 +
 drivers/pci/controller/dwc/Makefile        |   1 +
 drivers/pci/controller/dwc/pcie-stm32-ep.c | 411 +++++++++++++++++++++
 drivers/pci/controller/dwc/pcie-stm32.h    |   1 +
 4 files changed, 425 insertions(+)
 create mode 100644 drivers/pci/controller/dwc/pcie-stm32-ep.c

diff --git a/drivers/pci/controller/dwc/Kconfig b/drivers/pci/controller/dwc/Kconfig
index 387151f25f5f..72b9c50c1dfd 100644
--- a/drivers/pci/controller/dwc/Kconfig
+++ b/drivers/pci/controller/dwc/Kconfig
@@ -422,6 +422,18 @@ config PCIE_STM32_HOST
 	  This driver can also be built as a module. If so, the module
 	  will be called pcie-stm32.
 
+config PCIE_STM32_EP
+	tristate "STMicroelectronics STM32MP25 PCIe Controller (endpoint mode)"
+	depends on ARCH_STM32 || COMPILE_TEST
+	depends on PCI_ENDPOINT
+	select PCIE_DW_EP
+	help
+	  Enables Endpoint (EP) support for the DesignWare core based PCIe
+	  controller found in STM32MP25 SoC.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called pcie-stm32-ep.
+
 config PCI_DRA7XX
 	tristate
 
diff --git a/drivers/pci/controller/dwc/Makefile b/drivers/pci/controller/dwc/Makefile
index 9d3b43504725..85ec6804a299 100644
--- a/drivers/pci/controller/dwc/Makefile
+++ b/drivers/pci/controller/dwc/Makefile
@@ -31,6 +31,7 @@ obj-$(CONFIG_PCIE_UNIPHIER_EP) += pcie-uniphier-ep.o
 obj-$(CONFIG_PCIE_VISCONTI_HOST) += pcie-visconti.o
 obj-$(CONFIG_PCIE_RCAR_GEN4) += pcie-rcar-gen4.o
 obj-$(CONFIG_PCIE_STM32_HOST) += pcie-stm32.o
+obj-$(CONFIG_PCIE_STM32_EP) += pcie-stm32-ep.o
 
 # The following drivers are for devices that use the generic ACPI
 # pci_root.c driver but don't support standard ECAM config access.
diff --git a/drivers/pci/controller/dwc/pcie-stm32-ep.c b/drivers/pci/controller/dwc/pcie-stm32-ep.c
new file mode 100644
index 000000000000..867826511319
--- /dev/null
+++ b/drivers/pci/controller/dwc/pcie-stm32-ep.c
@@ -0,0 +1,411 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * STMicroelectronics STM32MP25 PCIe endpoint driver.
+ *
+ * Copyright (C) 2025 STMicroelectronics
+ * Author: Christian Bruel <christian.bruel@foss.st.com>
+ */
+
+#include <linux/clk.h>
+#include <linux/mfd/syscon.h>
+#include <linux/of_platform.h>
+#include <linux/of_gpio.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+#include "pcie-designware.h"
+#include "pcie-stm32.h"
+
+enum stm32_pcie_ep_link_status {
+	STM32_PCIE_EP_LINK_DISABLED,
+	STM32_PCIE_EP_LINK_ENABLED,
+};
+
+struct stm32_pcie {
+	struct dw_pcie pci;
+	struct regmap *regmap;
+	struct reset_control *rst;
+	struct phy *phy;
+	struct clk *clk;
+	struct gpio_desc *perst_gpio;
+	enum stm32_pcie_ep_link_status link_status;
+	unsigned int perst_irq;
+};
+
+static void stm32_pcie_ep_init(struct dw_pcie_ep *ep)
+{
+	struct dw_pcie *pci = to_dw_pcie_from_ep(ep);
+	enum pci_barno bar;
+
+	for (bar = 0; bar < PCI_STD_NUM_BARS; bar++)
+		dw_pcie_ep_reset_bar(pci, bar);
+}
+
+static int stm32_pcie_enable_link(struct dw_pcie *pci)
+{
+	struct stm32_pcie *stm32_pcie = to_stm32_pcie(pci);
+
+	regmap_update_bits(stm32_pcie->regmap, SYSCFG_PCIECR,
+			   STM32MP25_PCIECR_LTSSM_EN,
+			   STM32MP25_PCIECR_LTSSM_EN);
+
+	return dw_pcie_wait_for_link(pci);
+}
+
+static void stm32_pcie_disable_link(struct dw_pcie *pci)
+{
+	struct stm32_pcie *stm32_pcie = to_stm32_pcie(pci);
+
+	regmap_update_bits(stm32_pcie->regmap, SYSCFG_PCIECR, STM32MP25_PCIECR_LTSSM_EN, 0);
+}
+
+static int stm32_pcie_start_link(struct dw_pcie *pci)
+{
+	struct stm32_pcie *stm32_pcie = to_stm32_pcie(pci);
+	int ret;
+
+	if (stm32_pcie->link_status == STM32_PCIE_EP_LINK_ENABLED) {
+		dev_dbg(pci->dev, "Link is already enabled\n");
+		return 0;
+	}
+
+	ret = stm32_pcie_enable_link(pci);
+	if (ret) {
+		dev_err(pci->dev, "PCIe cannot establish link: %d\n", ret);
+		return ret;
+	}
+
+	stm32_pcie->link_status = STM32_PCIE_EP_LINK_ENABLED;
+
+	enable_irq(stm32_pcie->perst_irq);
+
+	return 0;
+}
+
+static void stm32_pcie_stop_link(struct dw_pcie *pci)
+{
+	struct stm32_pcie *stm32_pcie = to_stm32_pcie(pci);
+
+	if (stm32_pcie->link_status == STM32_PCIE_EP_LINK_DISABLED) {
+		dev_dbg(pci->dev, "Link is already disabled\n");
+		return;
+	}
+
+	disable_irq(stm32_pcie->perst_irq);
+
+	stm32_pcie_disable_link(pci);
+
+	stm32_pcie->link_status = STM32_PCIE_EP_LINK_DISABLED;
+}
+
+static int stm32_pcie_raise_irq(struct dw_pcie_ep *ep, u8 func_no,
+				unsigned int type, u16 interrupt_num)
+{
+	struct dw_pcie *pci = to_dw_pcie_from_ep(ep);
+
+	switch (type) {
+	case PCI_IRQ_INTX:
+		return dw_pcie_ep_raise_intx_irq(ep, func_no);
+	case PCI_IRQ_MSI:
+		return dw_pcie_ep_raise_msi_irq(ep, func_no, interrupt_num);
+	default:
+		dev_err(pci->dev, "UNKNOWN IRQ type\n");
+		return -EINVAL;
+	}
+}
+
+static const struct pci_epc_features stm32_pcie_epc_features = {
+	.msi_capable = true,
+	.align = SZ_64K,
+};
+
+static const struct pci_epc_features*
+stm32_pcie_get_features(struct dw_pcie_ep *ep)
+{
+	return &stm32_pcie_epc_features;
+}
+
+static const struct dw_pcie_ep_ops stm32_pcie_ep_ops = {
+	.init = stm32_pcie_ep_init,
+	.raise_irq = stm32_pcie_raise_irq,
+	.get_features = stm32_pcie_get_features,
+};
+
+static const struct dw_pcie_ops dw_pcie_ops = {
+	.start_link = stm32_pcie_start_link,
+	.stop_link = stm32_pcie_stop_link,
+};
+
+static int stm32_pcie_enable_resources(struct stm32_pcie *stm32_pcie)
+{
+	int ret;
+
+	ret = phy_init(stm32_pcie->phy);
+	if (ret)
+		return ret;
+
+	ret = clk_prepare_enable(stm32_pcie->clk);
+	if (ret)
+		phy_exit(stm32_pcie->phy);
+
+	return ret;
+}
+
+static void stm32_pcie_disable_resources(struct stm32_pcie *stm32_pcie)
+{
+	clk_disable_unprepare(stm32_pcie->clk);
+
+	phy_exit(stm32_pcie->phy);
+}
+
+static void stm32_pcie_perst_assert(struct dw_pcie *pci)
+{
+	struct stm32_pcie *stm32_pcie = to_stm32_pcie(pci);
+	struct dw_pcie_ep *ep = &stm32_pcie->pci.ep;
+	struct device *dev = pci->dev;
+
+	dev_dbg(dev, "PERST asserted by host\n");
+
+	if (stm32_pcie->link_status == STM32_PCIE_EP_LINK_DISABLED) {
+		dev_dbg(pci->dev, "Link is already disabled\n");
+		return;
+	}
+
+	pci_epc_deinit_notify(ep->epc);
+
+	stm32_pcie_disable_resources(stm32_pcie);
+
+	pm_runtime_put_sync(dev);
+
+	stm32_pcie->link_status = STM32_PCIE_EP_LINK_DISABLED;
+}
+
+static void stm32_pcie_perst_deassert(struct dw_pcie *pci)
+{
+	struct stm32_pcie *stm32_pcie = to_stm32_pcie(pci);
+	struct device *dev = pci->dev;
+	struct dw_pcie_ep *ep = &pci->ep;
+	int ret;
+
+	if (stm32_pcie->link_status == STM32_PCIE_EP_LINK_ENABLED) {
+		dev_dbg(pci->dev, "Link is already enabled\n");
+		return;
+	}
+
+	dev_dbg(dev, "PERST de-asserted by host\n");
+
+	ret = pm_runtime_resume_and_get(dev);
+	if (ret < 0) {
+		dev_err(dev, "Failed to resume runtime PM: %d\n", ret);
+		return;
+	}
+
+	ret = stm32_pcie_enable_resources(stm32_pcie);
+	if (ret) {
+		dev_err(dev, "Failed to enable resources: %d\n", ret);
+		goto err_pm_put_sync;
+	}
+
+	/*
+	 * Need to reprogram the configuration space registers here because the
+	 * DBI registers were incorrectly reset by the PHY RCC during phy_init().
+	 */
+	ret = dw_pcie_ep_init_registers(ep);
+	if (ret) {
+		dev_err(dev, "Failed to complete initialization: %d\n", ret);
+		goto err_disable_resources;
+	}
+
+	pci_epc_init_notify(ep->epc);
+
+	stm32_pcie->link_status = STM32_PCIE_EP_LINK_ENABLED;
+
+	return;
+
+err_disable_resources:
+	stm32_pcie_disable_resources(stm32_pcie);
+
+err_pm_put_sync:
+	pm_runtime_put_sync(dev);
+}
+
+static irqreturn_t stm32_pcie_ep_perst_irq_thread(int irq, void *data)
+{
+	struct stm32_pcie *stm32_pcie = data;
+	struct dw_pcie *pci = &stm32_pcie->pci;
+	u32 perst;
+
+	perst = gpiod_get_value(stm32_pcie->perst_gpio);
+	if (perst)
+		stm32_pcie_perst_assert(pci);
+	else
+		stm32_pcie_perst_deassert(pci);
+
+	return IRQ_HANDLED;
+}
+
+static int stm32_add_pcie_ep(struct stm32_pcie *stm32_pcie,
+			     struct platform_device *pdev)
+{
+	struct dw_pcie_ep *ep = &stm32_pcie->pci.ep;
+	struct device *dev = &pdev->dev;
+	int ret;
+
+	ret = regmap_update_bits(stm32_pcie->regmap, SYSCFG_PCIECR,
+				 STM32MP25_PCIECR_TYPE_MASK,
+				 STM32MP25_PCIECR_EP);
+	if (ret)
+		return ret;
+
+	reset_control_assert(stm32_pcie->rst);
+	reset_control_deassert(stm32_pcie->rst);
+
+	ep->ops = &stm32_pcie_ep_ops;
+
+	ret = dw_pcie_ep_init(ep);
+	if (ret) {
+		dev_err(dev, "Failed to initialize ep: %d\n", ret);
+		return ret;
+	}
+
+	ret = stm32_pcie_enable_resources(stm32_pcie);
+	if (ret) {
+		dev_err(dev, "Failed to enable resources: %d\n", ret);
+		goto err_ep_deinit;
+	}
+
+	ret = dw_pcie_ep_init_registers(ep);
+	if (ret) {
+		dev_err(dev, "Failed to initialize DWC endpoint registers\n");
+		goto err_disable_resources;
+	}
+
+	pci_epc_init_notify(ep->epc);
+
+	return 0;
+
+err_disable_resources:
+	stm32_pcie_disable_resources(stm32_pcie);
+
+err_ep_deinit:
+	dw_pcie_ep_deinit(ep);
+
+	return ret;
+}
+
+static int stm32_pcie_probe(struct platform_device *pdev)
+{
+	struct stm32_pcie *stm32_pcie;
+	struct device *dev = &pdev->dev;
+	int ret;
+
+	stm32_pcie = devm_kzalloc(dev, sizeof(*stm32_pcie), GFP_KERNEL);
+	if (!stm32_pcie)
+		return -ENOMEM;
+
+	stm32_pcie->pci.dev = dev;
+	stm32_pcie->pci.ops = &dw_pcie_ops;
+
+	stm32_pcie->regmap = syscon_regmap_lookup_by_compatible("st,stm32mp25-syscfg");
+	if (IS_ERR(stm32_pcie->regmap))
+		return dev_err_probe(dev, PTR_ERR(stm32_pcie->regmap),
+				     "No syscfg specified\n");
+
+	stm32_pcie->phy = devm_phy_get(dev, NULL);
+	if (IS_ERR(stm32_pcie->phy))
+		return dev_err_probe(dev, PTR_ERR(stm32_pcie->phy),
+				     "failed to get pcie-phy\n");
+
+	stm32_pcie->clk = devm_clk_get(dev, NULL);
+	if (IS_ERR(stm32_pcie->clk))
+		return dev_err_probe(dev, PTR_ERR(stm32_pcie->clk),
+				     "Failed to get PCIe clock source\n");
+
+	stm32_pcie->rst = devm_reset_control_get_exclusive(dev, NULL);
+	if (IS_ERR(stm32_pcie->rst))
+		return dev_err_probe(dev, PTR_ERR(stm32_pcie->rst),
+				     "Failed to get PCIe reset\n");
+
+	stm32_pcie->perst_gpio = devm_gpiod_get(dev, "reset", GPIOD_IN);
+	if (IS_ERR(stm32_pcie->perst_gpio))
+		return dev_err_probe(dev, PTR_ERR(stm32_pcie->perst_gpio),
+				     "Failed to get reset GPIO\n");
+
+	ret = phy_set_mode(stm32_pcie->phy, PHY_MODE_PCIE);
+	if (ret)
+		return ret;
+
+	platform_set_drvdata(pdev, stm32_pcie);
+
+	pm_runtime_get_noresume(dev);
+
+	ret = devm_pm_runtime_enable(dev);
+	if (ret < 0) {
+		pm_runtime_put_noidle(&pdev->dev);
+		return dev_err_probe(dev, ret, "Failed to enable runtime PM\n");
+	}
+
+	stm32_pcie->perst_irq = gpiod_to_irq(stm32_pcie->perst_gpio);
+
+	/* Will be enabled in start_link when device is initialized. */
+	irq_set_status_flags(stm32_pcie->perst_irq, IRQ_NOAUTOEN);
+
+	ret = devm_request_threaded_irq(dev, stm32_pcie->perst_irq, NULL,
+					stm32_pcie_ep_perst_irq_thread,
+					IRQF_TRIGGER_RISING |
+					IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
+					"perst_irq", stm32_pcie);
+	if (ret) {
+		dev_err(dev, "Failed to request PERST IRQ: %d\n", ret);
+		pm_runtime_put_noidle(&pdev->dev);
+		return ret;
+	}
+
+	ret = stm32_add_pcie_ep(stm32_pcie, pdev);
+	if (ret)
+		pm_runtime_put_noidle(&pdev->dev);
+
+	return ret;
+}
+
+static void stm32_pcie_remove(struct platform_device *pdev)
+{
+	struct stm32_pcie *stm32_pcie = platform_get_drvdata(pdev);
+	struct dw_pcie *pci = &stm32_pcie->pci;
+	struct dw_pcie_ep *ep = &pci->ep;
+
+	if (stm32_pcie->link_status == STM32_PCIE_EP_LINK_ENABLED) {
+		disable_irq(stm32_pcie->perst_irq);
+		stm32_pcie_disable_link(pci);
+	}
+
+	pci_epc_deinit_notify(ep->epc);
+	dw_pcie_ep_deinit(ep);
+
+	stm32_pcie_disable_resources(stm32_pcie);
+
+	pm_runtime_put_sync(&pdev->dev);
+}
+
+static const struct of_device_id stm32_pcie_ep_of_match[] = {
+	{ .compatible = "st,stm32mp25-pcie-ep" },
+	{},
+};
+
+static struct platform_driver stm32_pcie_ep_driver = {
+	.probe = stm32_pcie_probe,
+	.remove = stm32_pcie_remove,
+	.driver = {
+		.name = "stm32-ep-pcie",
+		.of_match_table = stm32_pcie_ep_of_match,
+	},
+};
+
+module_platform_driver(stm32_pcie_ep_driver);
+
+MODULE_AUTHOR("Christian Bruel <christian.bruel@foss.st.com>");
+MODULE_DESCRIPTION("STM32MP25 PCIe Endpoint Controller driver");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(of, stm32_pcie_ep_of_match);
diff --git a/drivers/pci/controller/dwc/pcie-stm32.h b/drivers/pci/controller/dwc/pcie-stm32.h
index 387112c4e42c..09d39f04e469 100644
--- a/drivers/pci/controller/dwc/pcie-stm32.h
+++ b/drivers/pci/controller/dwc/pcie-stm32.h
@@ -9,6 +9,7 @@
 #define to_stm32_pcie(x)	dev_get_drvdata((x)->dev)
 
 #define STM32MP25_PCIECR_TYPE_MASK	GENMASK(11, 8)
+#define STM32MP25_PCIECR_EP		0
 #define STM32MP25_PCIECR_LTSSM_EN	BIT(2)
 #define STM32MP25_PCIECR_RC		BIT(10)
 
-- 
2.34.1

[PATCH v9 5/9] MAINTAINERS: add entry for ST STM32MP25 PCIe drivers

[Christian Bruel]

Add myself as maintainer of STM32MP25 PCIe host and PCIe endpoint drivers

Signed-off-by: Christian Bruel <christian.bruel@foss.st.com>
---
 MAINTAINERS | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/MAINTAINERS b/MAINTAINERS
index d74250b2e8e6..2140f668a3c2 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -18912,6 +18912,13 @@ L:	linux-samsung-soc@vger.kernel.org
 S:	Maintained
 F:	drivers/pci/controller/dwc/pci-exynos.c
 
+PCI DRIVER FOR STM32MP25
+M:	Christian Bruel <christian.bruel@foss.st.com>
+L:	linux-pci@vger.kernel.org
+S:	Maintained
+F:	Documentation/devicetree/bindings/pci/st,stm32-pcie-*.yaml
+F:	drivers/pci/controller/dwc/*stm32*
+
 PCI DRIVER FOR SYNOPSYS DESIGNWARE
 M:	Jingoo Han <jingoohan1@gmail.com>
 M:	Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
-- 
2.34.1

[PATCH v9 6/9] arm64: dts: st: add PCIe pinctrl entries in stm32mp25-pinctrl.dtsi

[Christian Bruel]

Add PCIe pinctrl entries in stm32mp25-pinctrl.dtsi
init: forces GPIO to low while probing so CLKREQ is low for
phy_init
default: restore the AFMUX after controller probe

Add Analog pins of PCIe to perform power cycle

Signed-off-by: Christian Bruel <christian.bruel@foss.st.com>
---
 arch/arm64/boot/dts/st/stm32mp25-pinctrl.dtsi | 20 +++++++++++++++++++
 1 file changed, 20 insertions(+)

diff --git a/arch/arm64/boot/dts/st/stm32mp25-pinctrl.dtsi b/arch/arm64/boot/dts/st/stm32mp25-pinctrl.dtsi
index aba90d555f4e..0480b9af00e8 100644
--- a/arch/arm64/boot/dts/st/stm32mp25-pinctrl.dtsi
+++ b/arch/arm64/boot/dts/st/stm32mp25-pinctrl.dtsi
@@ -133,6 +133,26 @@ pins {
 		};
 	};
 
+	pcie_pins_a: pcie-0 {
+		pins {
+			pinmux = <STM32_PINMUX('J', 0, AF4)>;
+			bias-disable;
+		};
+	};
+
+	pcie_init_pins_a: pcie-init-0 {
+		pins {
+			pinmux = <STM32_PINMUX('J', 0, GPIO)>;
+			output-low;
+		};
+	};
+
+	pcie_sleep_pins_a: pcie-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('J', 0, ANALOG)>;
+		};
+	};
+
 	sdmmc1_b4_pins_a: sdmmc1-b4-0 {
 		pins1 {
 			pinmux = <STM32_PINMUX('E', 4, AF10)>, /* SDMMC1_D0 */
-- 
2.34.1

[PATCH v9 7/9] arm64: dts: st: Add PCIe Root Complex mode on stm32mp251

[Christian Bruel]

Add pcie_rc node to support STM32 MP25 PCIe driver based on the
DesignWare PCIe core configured as Root Complex mode

Supports Gen1/Gen2, single lane, MSI interrupts using the ARM GICv2m

Signed-off-by: Christian Bruel <christian.bruel@foss.st.com>
---
 arch/arm64/boot/dts/st/stm32mp251.dtsi | 44 ++++++++++++++++++++++++++
 1 file changed, 44 insertions(+)

diff --git a/arch/arm64/boot/dts/st/stm32mp251.dtsi b/arch/arm64/boot/dts/st/stm32mp251.dtsi
index d6993d3dc14d..7978fd640e1e 100644
--- a/arch/arm64/boot/dts/st/stm32mp251.dtsi
+++ b/arch/arm64/boot/dts/st/stm32mp251.dtsi
@@ -122,6 +122,15 @@ intc: interrupt-controller@4ac00000 {
 		      <0x0 0x4ac20000 0x0 0x20000>,
 		      <0x0 0x4ac40000 0x0 0x20000>,
 		      <0x0 0x4ac60000 0x0 0x20000>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		v2m0: v2m@48090000 {
+			compatible = "arm,gic-v2m-frame";
+			reg = <0x0 0x48090000 0x0 0x1000>;
+			msi-controller;
+		};
 	};
 
 	psci {
@@ -953,6 +962,41 @@ stmmac_axi_config_1: stmmac-axi-config {
 					snps,wr_osr_lmt = <0x7>;
 				};
 			};
+
+			pcie_rc: pcie@48400000 {
+				compatible = "st,stm32mp25-pcie-rc";
+				device_type = "pci";
+				reg = <0x48400000 0x400000>,
+				      <0x10000000 0x10000>;
+				reg-names = "dbi", "config";
+				#interrupt-cells = <1>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &intc 0 0 GIC_SPI 264 IRQ_TYPE_LEVEL_HIGH>,
+						<0 0 0 2 &intc 0 0 GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>,
+						<0 0 0 3 &intc 0 0 GIC_SPI 266 IRQ_TYPE_LEVEL_HIGH>,
+						<0 0 0 4 &intc 0 0 GIC_SPI 267 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				ranges = <0x01000000 0x0 0x00000000 0x10010000 0x0 0x10000>,
+					 <0x02000000 0x0 0x10020000 0x10020000 0x0 0x7fe0000>,
+					 <0x42000000 0x0 0x18000000 0x18000000 0x0 0x8000000>;
+				dma-ranges = <0x42000000 0x0 0x80000000 0x80000000 0x0 0x80000000>;
+				clocks = <&rcc CK_BUS_PCIE>;
+				resets = <&rcc PCIE_R>;
+				msi-parent = <&v2m0>;
+				access-controllers = <&rifsc 68>;
+				power-domains = <&CLUSTER_PD>;
+				status = "disabled";
+
+				pcie@0,0 {
+					device_type = "pci";
+					reg = <0x0 0x0 0x0 0x0 0x0>;
+					phys = <&combophy PHY_TYPE_PCIE>;
+					#address-cells = <3>;
+					#size-cells = <2>;
+					ranges;
+				};
+			};
 		};
 
 		bsec: efuse@44000000 {
-- 
2.34.1

[PATCH v9 8/9] arm64: dts: st: Add PCIe Endpoint mode on stm32mp251

[Christian Bruel]

Add pcie_ep node to support STM32 MP25 PCIe driver based on the
DesignWare PCIe core configured as Endpoint mode

Signed-off-by: Christian Bruel <christian.bruel@foss.st.com>
---
 arch/arm64/boot/dts/st/stm32mp251.dtsi | 15 +++++++++++++++
 1 file changed, 15 insertions(+)

diff --git a/arch/arm64/boot/dts/st/stm32mp251.dtsi b/arch/arm64/boot/dts/st/stm32mp251.dtsi
index 7978fd640e1e..6d54ed9a1052 100644
--- a/arch/arm64/boot/dts/st/stm32mp251.dtsi
+++ b/arch/arm64/boot/dts/st/stm32mp251.dtsi
@@ -963,6 +963,21 @@ stmmac_axi_config_1: stmmac-axi-config {
 				};
 			};
 
+			pcie_ep: pcie-ep@48400000 {
+				compatible = "st,stm32mp25-pcie-ep";
+				reg = <0x48400000 0x100000>,
+				      <0x48500000 0x100000>,
+				      <0x48700000 0x80000>,
+				      <0x10000000 0x8000000>;
+				reg-names = "dbi", "dbi2", "atu", "addr_space";
+				clocks = <&rcc CK_BUS_PCIE>;
+				resets = <&rcc PCIE_R>;
+				phys = <&combophy PHY_TYPE_PCIE>;
+				access-controllers = <&rifsc 68>;
+				power-domains = <&CLUSTER_PD>;
+				status = "disabled";
+			};
+
 			pcie_rc: pcie@48400000 {
 				compatible = "st,stm32mp25-pcie-rc";
 				device_type = "pci";
-- 
2.34.1

[PATCH v9 9/9] arm64: dts: st: Enable PCIe on the stm32mp257f-ev1 board

[Christian Bruel]

Add PCIe RC and EP support on stm32mp257f-ev1 board.
Default to RC mode.

Signed-off-by: Christian Bruel <christian.bruel@foss.st.com>
---
 arch/arm64/boot/dts/st/stm32mp257f-ev1.dts | 21 +++++++++++++++++++++
 1 file changed, 21 insertions(+)

diff --git a/arch/arm64/boot/dts/st/stm32mp257f-ev1.dts b/arch/arm64/boot/dts/st/stm32mp257f-ev1.dts
index 9d1a1155e36c..85f99a1ca154 100644
--- a/arch/arm64/boot/dts/st/stm32mp257f-ev1.dts
+++ b/arch/arm64/boot/dts/st/stm32mp257f-ev1.dts
@@ -257,6 +257,27 @@ scmi_vdd_sdcard: regulator@23 {
 	};
 };
 
+&pcie_ep {
+	pinctrl-names = "default", "init";
+	pinctrl-0 = <&pcie_pins_a>;
+	pinctrl-1 = <&pcie_init_pins_a>;
+	reset-gpios = <&gpioj 8 GPIO_ACTIVE_LOW>;
+	status = "disabled";
+};
+
+&pcie_rc {
+	pinctrl-names = "default", "init", "sleep";
+	pinctrl-0 = <&pcie_pins_a>;
+	pinctrl-1 = <&pcie_init_pins_a>;
+	pinctrl-2 = <&pcie_sleep_pins_a>;
+	status = "okay";
+
+	pcie@0,0 {
+		 reset-gpios = <&gpioj 8 GPIO_ACTIVE_LOW>;
+		 wake-gpios = <&gpioh 5 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	};
+};
+
 &sdmmc1 {
 	pinctrl-names = "default", "opendrain", "sleep";
 	pinctrl-0 = <&sdmmc1_b4_pins_a>;
-- 
2.34.1

Re: [PATCH v9 0/9] Add STM32MP25 PCIe drivers

[Rob Herring (Arm)]

On Wed, 14 May 2025 11:15:21 +0200, Christian Bruel wrote:
> Changes in v9:
>    - Describe atu and dbi2 shadowed registers in pcie_ep node
>    Address RC and EP drivers comments from Manivanna:
>    - Use dev_error_probe() for pm_runtime_enable() calls
>    - Reword Kconfig help message
>    - Move pm_runtime_get_noresume() before devm_pm_runtime_enable()
> 
> Changes in v8:
>    - Whitespace in comment
> 
> Changes in v7:
>    - Use device_init_wakeup to enable wakeup
>    - Fix comments (Bjorn)
> 
> Changes in v6:
>    - Call device_wakeup_enable() to fix WAKE# wakeup.
>    Address comments from Manivanna:
>    - Fix/Add Comments
>    - Fix DT indents
>    - Remove dw_pcie_ep_linkup() in EP start link
>    - Add PCIE_T_PVPERL_MS delay in RC PERST# deassert
> 
> Changes in v5:
>    Address driver comments from Manivanna:
>    - Use dw_pcie_{suspend/resume}_noirq instead of private ones.
>    - Move dw_pcie_host_init() to probe
>    - Add stm32_remove_pcie_port cleanup function
>    - Use of_node_put in stm32_pcie_parse_port
>    - Remove wakeup-source property
>    - Use generic dev_pm_set_dedicated_wake_irq to support wake# irq
> 
> Changes in v4:
>    Address bindings comments Rob Herring
>    - Remove phy property form common yaml
>    - Remove phy-name property
>    - Move wake_gpio and reset_gpio to the host root port
> 
> Changes in v3:
>    Address comments from Manivanna, Rob and Bjorn:
>    - Move host wakeup helper to dwc core (Mani)
>    - Drop num-lanes=<1> from bindings (Rob)
>    - Fix PCI address of I/O region (Mani)
>    - Moved PHY to a RC rootport subsection (Bjorn, Mani)
>    - Replaced dma-limit quirk by dma-ranges property (Bjorn)
>    - Moved out perst assert/deassert from start/stop link (Mani)
>    - Drop link_up test optim (Mani)
>    - DT and comments rephrasing (Bjorn)
>    - Add dts entries now that the combophy entries has landed
>    - Drop delaying Configuration Requests
> 
> Changes in v2:
>    - Fix st,stm32-pcie-common.yaml dt_binding_check
> 
> Changes in v1:
>    Address comments from Rob Herring and Bjorn Helgaas:
>    - Drop st,limit-mrrs and st,max-payload-size from this patchset
>    - Remove single reset and clocks binding names and misc yaml cleanups
>    - Split RC/EP common bindings to a separate schema file
>    - Use correct PCIE_T_PERST_CLK_US and PCIE_T_RRS_READY_MS defines
>    - Use .remove instead of .remove_new
>    - Fix bar reset sequence in EP driver
>    - Use cleanup blocks for error handling
>    - Cosmetic fixes
> 
> Christian Bruel (9):
>   dt-bindings: PCI: Add STM32MP25 PCIe Root Complex bindings
>   PCI: stm32: Add PCIe host support for STM32MP25
>   dt-bindings: PCI: Add STM32MP25 PCIe Endpoint bindings
>   PCI: stm32: Add PCIe Endpoint support for STM32MP25
>   MAINTAINERS: add entry for ST STM32MP25 PCIe drivers
>   arm64: dts: st: add PCIe pinctrl entries in stm32mp25-pinctrl.dtsi
>   arm64: dts: st: Add PCIe Root Complex mode on stm32mp251
>   arm64: dts: st: Add PCIe Endpoint mode on stm32mp251
>   arm64: dts: st: Enable PCIe on the stm32mp257f-ev1 board
> 
>  .../bindings/pci/st,stm32-pcie-common.yaml    |  33 ++
>  .../bindings/pci/st,stm32-pcie-ep.yaml        |  67 +++
>  .../bindings/pci/st,stm32-pcie-host.yaml      | 112 +++++
>  MAINTAINERS                                   |   7 +
>  arch/arm64/boot/dts/st/stm32mp25-pinctrl.dtsi |  20 +
>  arch/arm64/boot/dts/st/stm32mp251.dtsi        |  57 +++
>  arch/arm64/boot/dts/st/stm32mp257f-ev1.dts    |  21 +
>  drivers/pci/controller/dwc/Kconfig            |  24 +
>  drivers/pci/controller/dwc/Makefile           |   2 +
>  drivers/pci/controller/dwc/pcie-stm32-ep.c    | 411 ++++++++++++++++++
>  drivers/pci/controller/dwc/pcie-stm32.c       | 364 ++++++++++++++++
>  drivers/pci/controller/dwc/pcie-stm32.h       |  16 +
>  12 files changed, 1134 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/pci/st,stm32-pcie-common.yaml
>  create mode 100644 Documentation/devicetree/bindings/pci/st,stm32-pcie-ep.yaml
>  create mode 100644 Documentation/devicetree/bindings/pci/st,stm32-pcie-host.yaml
>  create mode 100644 drivers/pci/controller/dwc/pcie-stm32-ep.c
>  create mode 100644 drivers/pci/controller/dwc/pcie-stm32.c
>  create mode 100644 drivers/pci/controller/dwc/pcie-stm32.h
> 
> --
> 2.34.1
> 
> 
> 


My bot found new DTB warnings on the .dts files added or changed in this
series.

Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
are fixed by another series. Ultimately, it is up to the platform
maintainer whether these warnings are acceptable or not. No need to reply
unless the platform maintainer has comments.

If you already ran DT checks and didn't see these error(s), then
make sure dt-schema is up to date:

  pip3 install dtschema --upgrade


This patch series was applied (using b4) to base:
 Base: attempting to guess base-commit...
 Base: tags/next-20250514 (best guess, 5/6 blobs matched)

If this is not the correct base, please add 'base-commit' tag
(or use b4 which does this automatically)

New warnings running 'make CHECK_DTBS=y for arch/arm64/boot/dts/st/' for 20250514091530.3249364-1-christian.bruel@foss.st.com:

arch/arm64/boot/dts/st/stm32mp257f-dk.dtb: pcie-ep@48400000 (st,stm32mp25-pcie-ep): reg: [[1212153856, 1048576], [1213202432, 1048576], [1215299584, 524288], [268435456, 134217728]] is too long
	from schema $id: http://devicetree.org/schemas/pci/st,stm32-pcie-ep.yaml#
arch/arm64/boot/dts/st/stm32mp257f-dk.dtb: pcie-ep@48400000 (st,stm32mp25-pcie-ep): reg-names:1: 'addr_space' was expected
	from schema $id: http://devicetree.org/schemas/pci/st,stm32-pcie-ep.yaml#
arch/arm64/boot/dts/st/stm32mp257f-dk.dtb: pcie-ep@48400000 (st,stm32mp25-pcie-ep): reg-names: ['dbi', 'dbi2', 'atu', 'addr_space'] is too long
	from schema $id: http://devicetree.org/schemas/pci/st,stm32-pcie-ep.yaml#
arch/arm64/boot/dts/st/stm32mp257f-ev1.dtb: pcie-ep@48400000 (st,stm32mp25-pcie-ep): reg: [[1212153856, 1048576], [1213202432, 1048576], [1215299584, 524288], [268435456, 134217728]] is too long
	from schema $id: http://devicetree.org/schemas/pci/st,stm32-pcie-ep.yaml#
arch/arm64/boot/dts/st/stm32mp257f-ev1.dtb: pcie-ep@48400000 (st,stm32mp25-pcie-ep): reg-names:1: 'addr_space' was expected
	from schema $id: http://devicetree.org/schemas/pci/st,stm32-pcie-ep.yaml#
arch/arm64/boot/dts/st/stm32mp257f-ev1.dtb: pcie-ep@48400000 (st,stm32mp25-pcie-ep): reg-names: ['dbi', 'dbi2', 'atu', 'addr_space'] is too long
	from schema $id: http://devicetree.org/schemas/pci/st,stm32-pcie-ep.yaml#

Re: [PATCH v9 0/9] Add STM32MP25 PCIe drivers

[Manivannan Sadhasivam]

On Wed, May 14, 2025 at 11:15:21AM +0200, Christian Bruel wrote:
> Changes in v9:
>    - Describe atu and dbi2 shadowed registers in pcie_ep node
>    Address RC and EP drivers comments from Manivanna:
>    - Use dev_error_probe() for pm_runtime_enable() calls
>    - Reword Kconfig help message
>    - Move pm_runtime_get_noresume() before devm_pm_runtime_enable()

Please do not post the next revision without resolving all the comments for the
previous one. It just adds more noise.

- Mani

> 
> Changes in v8:
>    - Whitespace in comment
>    
> Changes in v7:
>    - Use device_init_wakeup to enable wakeup
>    - Fix comments (Bjorn)
> 
> Changes in v6:
>    - Call device_wakeup_enable() to fix WAKE# wakeup.
>    Address comments from Manivanna:
>    - Fix/Add Comments
>    - Fix DT indents
>    - Remove dw_pcie_ep_linkup() in EP start link
>    - Add PCIE_T_PVPERL_MS delay in RC PERST# deassert
>    
> Changes in v5:
>    Address driver comments from Manivanna:
>    - Use dw_pcie_{suspend/resume}_noirq instead of private ones.
>    - Move dw_pcie_host_init() to probe
>    - Add stm32_remove_pcie_port cleanup function
>    - Use of_node_put in stm32_pcie_parse_port
>    - Remove wakeup-source property
>    - Use generic dev_pm_set_dedicated_wake_irq to support wake# irq
>    
> Changes in v4:
>    Address bindings comments Rob Herring
>    - Remove phy property form common yaml
>    - Remove phy-name property
>    - Move wake_gpio and reset_gpio to the host root port
>    
> Changes in v3:
>    Address comments from Manivanna, Rob and Bjorn:
>    - Move host wakeup helper to dwc core (Mani)
>    - Drop num-lanes=<1> from bindings (Rob)
>    - Fix PCI address of I/O region (Mani)
>    - Moved PHY to a RC rootport subsection (Bjorn, Mani)
>    - Replaced dma-limit quirk by dma-ranges property (Bjorn)
>    - Moved out perst assert/deassert from start/stop link (Mani)
>    - Drop link_up test optim (Mani)
>    - DT and comments rephrasing (Bjorn)
>    - Add dts entries now that the combophy entries has landed
>    - Drop delaying Configuration Requests
> 
> Changes in v2:
>    - Fix st,stm32-pcie-common.yaml dt_binding_check	
> 
> Changes in v1:
>    Address comments from Rob Herring and Bjorn Helgaas:
>    - Drop st,limit-mrrs and st,max-payload-size from this patchset
>    - Remove single reset and clocks binding names and misc yaml cleanups
>    - Split RC/EP common bindings to a separate schema file
>    - Use correct PCIE_T_PERST_CLK_US and PCIE_T_RRS_READY_MS defines
>    - Use .remove instead of .remove_new
>    - Fix bar reset sequence in EP driver
>    - Use cleanup blocks for error handling
>    - Cosmetic fixes
> 
> Christian Bruel (9):
>   dt-bindings: PCI: Add STM32MP25 PCIe Root Complex bindings
>   PCI: stm32: Add PCIe host support for STM32MP25
>   dt-bindings: PCI: Add STM32MP25 PCIe Endpoint bindings
>   PCI: stm32: Add PCIe Endpoint support for STM32MP25
>   MAINTAINERS: add entry for ST STM32MP25 PCIe drivers
>   arm64: dts: st: add PCIe pinctrl entries in stm32mp25-pinctrl.dtsi
>   arm64: dts: st: Add PCIe Root Complex mode on stm32mp251
>   arm64: dts: st: Add PCIe Endpoint mode on stm32mp251
>   arm64: dts: st: Enable PCIe on the stm32mp257f-ev1 board
> 
>  .../bindings/pci/st,stm32-pcie-common.yaml    |  33 ++
>  .../bindings/pci/st,stm32-pcie-ep.yaml        |  67 +++
>  .../bindings/pci/st,stm32-pcie-host.yaml      | 112 +++++
>  MAINTAINERS                                   |   7 +
>  arch/arm64/boot/dts/st/stm32mp25-pinctrl.dtsi |  20 +
>  arch/arm64/boot/dts/st/stm32mp251.dtsi        |  57 +++
>  arch/arm64/boot/dts/st/stm32mp257f-ev1.dts    |  21 +
>  drivers/pci/controller/dwc/Kconfig            |  24 +
>  drivers/pci/controller/dwc/Makefile           |   2 +
>  drivers/pci/controller/dwc/pcie-stm32-ep.c    | 411 ++++++++++++++++++
>  drivers/pci/controller/dwc/pcie-stm32.c       | 364 ++++++++++++++++
>  drivers/pci/controller/dwc/pcie-stm32.h       |  16 +
>  12 files changed, 1134 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/pci/st,stm32-pcie-common.yaml
>  create mode 100644 Documentation/devicetree/bindings/pci/st,stm32-pcie-ep.yaml
>  create mode 100644 Documentation/devicetree/bindings/pci/st,stm32-pcie-host.yaml
>  create mode 100644 drivers/pci/controller/dwc/pcie-stm32-ep.c
>  create mode 100644 drivers/pci/controller/dwc/pcie-stm32.c
>  create mode 100644 drivers/pci/controller/dwc/pcie-stm32.h
> 
> -- 
> 2.34.1
> 

-- 
மணிவண்ணன் சதாசிவம்