[PATCH v2] arm64: dts: ti: k3-am62a7-sk: add boot phase tags

[PATCH v2] arm64: dts: ti: k3-am62a7-sk: add boot phase tags

[Bryan Brattlof]

The 'bootph-all' tag was added to the dt-schema to describe the various
nodes used during the different phases of bootup with DT. Add the
bootph-all tag to all nodes that are used during the early stages of
bootup by the bootloaders.

This includes the console UART along with the SD and eMMC nodes and its
required regulators for the 3v3 to 1v8 transition and the various nodes
for Ethernet booting.

Signed-off-by: Bryan Brattlof <bb@ti.com>
---
Changes in v2:
- removed tag from ethernet-ports{} as it was redundant
- Link to v1: https://lore.kernel.org/r/20250709-62a-uboot-cleanup-v1-1-70f8e6cde719@ti.com
---
 arch/arm64/boot/dts/ti/k3-am62a7-sk.dts | 17 +++++++++++++++++
 1 file changed, 17 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
index f11284b3fe8e23b4c48d8d2f3a7202e80dc57370..bceead5e288e6d78c671baf0afabd1a9aa23fbee 100644
--- a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
@@ -36,6 +36,7 @@ memory@80000000 {
 		/* 4G RAM */
 		reg = <0x00000000 0x80000000 0x00000000 0x80000000>,
 		      <0x00000008 0x80000000 0x00000000 0x80000000>;
+		bootph-all;
 	};
 
 	reserved-memory {
@@ -151,6 +152,7 @@ vdd_mmc1: regulator-3 {
 		regulator-boot-on;
 		enable-active-high;
 		gpio = <&exp1 3 GPIO_ACTIVE_HIGH>;
+		bootph-all;
 	};
 
 	vcc_3v3_sys: regulator-4 {
@@ -297,6 +299,7 @@ main_uart0_pins_default: main-uart0-default-pins {
 			AM62AX_IOPAD(0x1c8, PIN_INPUT, 0) /* (E14) UART0_RXD */
 			AM62AX_IOPAD(0x1cc, PIN_OUTPUT, 0) /* (D15) UART0_TXD */
 		>;
+		bootph-all;
 	};
 
 	main_uart1_pins_default: main-uart1-default-pins {
@@ -320,6 +323,7 @@ main_i2c1_pins_default: main-i2c1-default-pins {
 			AM62AX_IOPAD(0x1e8, PIN_INPUT_PULLUP, 0) /* (B17) I2C1_SCL */
 			AM62AX_IOPAD(0x1ec, PIN_INPUT_PULLUP, 0) /* (A17) I2C1_SDA */
 		>;
+		bootph-all;
 	};
 
 	main_i2c2_pins_default: main-i2c2-default-pins {
@@ -356,6 +360,7 @@ AM62AX_IOPAD(0x228, PIN_INPUT, 0) /* (C21) MMC1_DAT2 */
 			AM62AX_IOPAD(0x224, PIN_INPUT, 0) /* (D22) MMC1_DAT3 */
 			AM62AX_IOPAD(0x240, PIN_INPUT, 0) /* (D17) MMC1_SDCD */
 		>;
+		bootph-all;
 	};
 
 	usr_led_pins_default: usr-led-default-pins {
@@ -375,6 +380,7 @@ main_mdio1_pins_default: main-mdio1-default-pins {
 			AM62AX_IOPAD(0x160, PIN_OUTPUT, 0) /* (V12) MDIO0_MDC */
 			AM62AX_IOPAD(0x15c, PIN_INPUT, 0) /* (V13) MDIO0_MDIO */
 		>;
+		bootph-all;
 	};
 
 	main_rgmii1_pins_default: main-rgmii1-default-pins {
@@ -392,6 +398,7 @@ AM62AX_IOPAD(0x140, PIN_INPUT, 0) /* (AA17) RGMII1_TD3 */
 			AM62AX_IOPAD(0x130, PIN_INPUT, 0) /* (AB17) RGMII1_TXC */
 			AM62AX_IOPAD(0x12c, PIN_INPUT, 0) /* (W16) RGMII1_TX_CTL */
 		>;
+		bootph-all;
 	};
 
 	main_mcasp1_pins_default: main-mcasp1-default-pins {
@@ -572,6 +579,7 @@ exp1: gpio@22 {
 		#interrupt-cells = <2>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&main_gpio1_ioexp_intr_pins_default>;
+		bootph-all;
 
 		gpio-line-names = "GPIO_CPSW2_RST", "GPIO_CPSW1_RST",
 				   "BT_EN_SOC", "MMC1_SD_EN",
@@ -675,10 +683,12 @@ &sdhci1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_mmc1_pins_default>;
 	disable-wp;
+	bootph-all;
 };
 
 &main_gpio0 {
 	status = "okay";
+	bootph-all;
 };
 
 &main_gpio1 {
@@ -693,6 +703,7 @@ &main_uart0 {
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_uart0_pins_default>;
+	bootph-all;
 };
 
 /* Main UART1 is used for TIFS firmware logs */
@@ -739,10 +750,15 @@ &cpsw3g {
 	pinctrl-0 = <&main_rgmii1_pins_default>;
 };
 
+&phy_gmii_sel {
+	bootph-all;
+};
+
 &cpsw_port1 {
 	status = "okay";
 	phy-mode = "rgmii-rxid";
 	phy-handle = <&cpsw3g_phy0>;
+	bootph-all;
 };
 
 &cpsw_port2 {
@@ -759,6 +775,7 @@ cpsw3g_phy0: ethernet-phy@0 {
 		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
 		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
 		ti,min-output-impedance;
+		bootph-all;
 	};
 };
 

---
base-commit: 3b08f8a34a2061d89a2411d04a675b3860d4f9cc
change-id: 20250623-62a-uboot-cleanup-b80e6952f91d

Best regards,
-- 
Bryan Brattlof <bb@ti.com>

Re: [PATCH v2] arm64: dts: ti: k3-am62a7-sk: add boot phase tags

[Vignesh Raghavendra]

Hi Bryan Brattlof,

On Thu, 10 Jul 2025 07:03:10 -0500, Bryan Brattlof wrote:
> The 'bootph-all' tag was added to the dt-schema to describe the various
> nodes used during the different phases of bootup with DT. Add the
> bootph-all tag to all nodes that are used during the early stages of
> bootup by the bootloaders.
> 
> This includes the console UART along with the SD and eMMC nodes and its
> required regulators for the 3v3 to 1v8 transition and the various nodes
> for Ethernet booting.
> 
> [...]

I have applied the following to branch ti-k3-dts-next on [1].
Thank you!

[1/1] arm64: dts: ti: k3-am62a7-sk: add boot phase tags
      commit: 289c5862b6c8984bbe840a6cd590225c6dd271f3

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent up the chain during
the next merge window (or sooner if it is a relevant bug fix), however if
problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux.git
--
Vignesh