From: John Madieu <john.madieu.xa@bp.renesas.com>
To: geert+renesas@glider.be, magnus.damm@gmail.com,
mturquette@baylibre.com, sboyd@kernel.org, rafael@kernel.org,
daniel.lezcano@linaro.org, rui.zhang@intel.com,
lukasz.luba@arm.com, robh@kernel.org, krzk+dt@kernel.org,
conor+dt@kernel.org, p.zabel@pengutronix.de,
catalin.marinas@arm.com, will@kernel.org
Cc: john.madieu@gmail.com, linux-renesas-soc@vger.kernel.org,
linux-kernel@vger.kernel.org, linux-pm@vger.kernel.org,
devicetree@vger.kernel.org, biju.das.jz@bp.renesas.com,
linux-arm-kernel@lists.infradead.org,
John Madieu <john.madieu.xa@bp.renesas.com>,
Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Subject: [PATCH v7 1/6] soc: renesas: rz-sysc: Add syscon/regmap support
Date: Mon, 18 Aug 2025 18:28:47 +0200 [thread overview]
Message-ID: <20250818162859.9661-2-john.madieu.xa@bp.renesas.com> (raw)
In-Reply-To: <20250818162859.9661-1-john.madieu.xa@bp.renesas.com>
The RZ/G3E system controller has various registers that control or report
some properties specific to individual IPs. The regmap is registered as a
syscon device to allow these IP drivers to access the registers through the
regmap API.
As other RZ SoCs might have custom read/write callbacks or max-offsets,
register a custom regmap configuration.
Signed-off-by: John Madieu <john.madieu.xa@bp.renesas.com>
[claudiu.beznea:
- do not check the match->data validity in rz_sysc_probe() as it is
always valid
- dinamically allocate regmap_cfg]
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
---
Changes:
v1 -> v2: no changes
v2 -> v3: no changes
v3 -> v4: no changes
v4 -> v5: no changes
v6: Addressed the review comments received at [1]
v7: As this is a duplicate of [2], address comment received there, that is,
use kzalloc() + kfree() for regmap_cfg.
[1] https://lore.kernel.org/all/20250330214945.185725-2-john.madieu.xa@bp.renesas.com/
[2] https://lore.kernel.org/all/20250808061806.2729274-1-claudiu.beznea.uj@bp.renesas.com/
drivers/soc/renesas/Kconfig | 1 +
drivers/soc/renesas/r9a08g045-sysc.c | 1 +
drivers/soc/renesas/r9a09g047-sys.c | 1 +
drivers/soc/renesas/r9a09g057-sys.c | 1 +
drivers/soc/renesas/rz-sysc.c | 28 +++++++++++++++++++++++++++-
drivers/soc/renesas/rz-sysc.h | 2 ++
6 files changed, 33 insertions(+), 1 deletion(-)
diff --git a/drivers/soc/renesas/Kconfig b/drivers/soc/renesas/Kconfig
index 719b7f4f376f..c97e2a183388 100644
--- a/drivers/soc/renesas/Kconfig
+++ b/drivers/soc/renesas/Kconfig
@@ -449,6 +449,7 @@ config RST_RCAR
config SYSC_RZ
bool "System controller for RZ SoCs" if COMPILE_TEST
+ select MFD_SYSCON
config SYSC_R9A08G045
bool "Renesas System controller support for R9A08G045 (RZ/G3S)" if COMPILE_TEST
diff --git a/drivers/soc/renesas/r9a08g045-sysc.c b/drivers/soc/renesas/r9a08g045-sysc.c
index f4db1431e036..0504d4e68761 100644
--- a/drivers/soc/renesas/r9a08g045-sysc.c
+++ b/drivers/soc/renesas/r9a08g045-sysc.c
@@ -20,4 +20,5 @@ static const struct rz_sysc_soc_id_init_data rzg3s_sysc_soc_id_init_data __initc
const struct rz_sysc_init_data rzg3s_sysc_init_data __initconst = {
.soc_id_init_data = &rzg3s_sysc_soc_id_init_data,
+ .max_register = 0xe20,
};
diff --git a/drivers/soc/renesas/r9a09g047-sys.c b/drivers/soc/renesas/r9a09g047-sys.c
index cd2eb7782cfe..2e8426c03050 100644
--- a/drivers/soc/renesas/r9a09g047-sys.c
+++ b/drivers/soc/renesas/r9a09g047-sys.c
@@ -64,4 +64,5 @@ static const struct rz_sysc_soc_id_init_data rzg3e_sys_soc_id_init_data __initco
const struct rz_sysc_init_data rzg3e_sys_init_data = {
.soc_id_init_data = &rzg3e_sys_soc_id_init_data,
+ .max_register = 0x170c,
};
diff --git a/drivers/soc/renesas/r9a09g057-sys.c b/drivers/soc/renesas/r9a09g057-sys.c
index 4c21cc29edbc..e3390e7c7fe5 100644
--- a/drivers/soc/renesas/r9a09g057-sys.c
+++ b/drivers/soc/renesas/r9a09g057-sys.c
@@ -64,4 +64,5 @@ static const struct rz_sysc_soc_id_init_data rzv2h_sys_soc_id_init_data __initco
const struct rz_sysc_init_data rzv2h_sys_init_data = {
.soc_id_init_data = &rzv2h_sys_soc_id_init_data,
+ .max_register = 0x170c,
};
diff --git a/drivers/soc/renesas/rz-sysc.c b/drivers/soc/renesas/rz-sysc.c
index ffa65fb4dade..c06758faf19f 100644
--- a/drivers/soc/renesas/rz-sysc.c
+++ b/drivers/soc/renesas/rz-sysc.c
@@ -6,8 +6,10 @@
*/
#include <linux/io.h>
+#include <linux/mfd/syscon.h>
#include <linux/of.h>
#include <linux/platform_device.h>
+#include <linux/regmap.h>
#include <linux/sys_soc.h>
#include "rz-sysc.h"
@@ -100,14 +102,23 @@ MODULE_DEVICE_TABLE(of, rz_sysc_match);
static int rz_sysc_probe(struct platform_device *pdev)
{
+ const struct rz_sysc_init_data *data;
const struct of_device_id *match;
struct device *dev = &pdev->dev;
+ struct regmap *regmap;
struct rz_sysc *sysc;
+ int ret;
+
+ struct regmap_config *regmap_cfg __free(kfree) = kzalloc(sizeof(*regmap_cfg), GFP_KERNEL);
+ if (!regmap_cfg)
+ return -ENOMEM;
match = of_match_node(rz_sysc_match, dev->of_node);
if (!match)
return -ENODEV;
+ data = match->data;
+
sysc = devm_kzalloc(dev, sizeof(*sysc), GFP_KERNEL);
if (!sysc)
return -ENOMEM;
@@ -117,7 +128,22 @@ static int rz_sysc_probe(struct platform_device *pdev)
return PTR_ERR(sysc->base);
sysc->dev = dev;
- return rz_sysc_soc_init(sysc, match);
+ ret = rz_sysc_soc_init(sysc, match);
+ if (ret)
+ return ret;
+
+ regmap_cfg->name = "rz_sysc_regs";
+ regmap_cfg->reg_bits = 32;
+ regmap_cfg->reg_stride = 4;
+ regmap_cfg->val_bits = 32;
+ regmap_cfg->fast_io = true;
+ regmap_cfg->max_register = data->max_register;
+
+ regmap = devm_regmap_init_mmio(dev, sysc->base, regmap_cfg);
+ if (IS_ERR(regmap))
+ return PTR_ERR(regmap);
+
+ return of_syscon_register_regmap(dev->of_node, regmap);
}
static struct platform_driver rz_sysc_driver = {
diff --git a/drivers/soc/renesas/rz-sysc.h b/drivers/soc/renesas/rz-sysc.h
index 56bc047a1bff..8eec355d5d56 100644
--- a/drivers/soc/renesas/rz-sysc.h
+++ b/drivers/soc/renesas/rz-sysc.h
@@ -34,9 +34,11 @@ struct rz_sysc_soc_id_init_data {
/**
* struct rz_sysc_init_data - RZ SYSC initialization data
* @soc_id_init_data: RZ SYSC SoC ID initialization data
+ * @max_register: Maximum SYSC register offset to be used by the regmap config
*/
struct rz_sysc_init_data {
const struct rz_sysc_soc_id_init_data *soc_id_init_data;
+ u32 max_register;
};
extern const struct rz_sysc_init_data rzg3e_sys_init_data;
--
2.25.1
next prev parent reply other threads:[~2025-08-18 18:48 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-08-18 16:28 [PATCH v7 0/6] thermal: renesas: Add support for RZ/G3E John Madieu
2025-08-18 16:28 ` John Madieu [this message]
2025-08-19 5:07 ` [PATCH v7 1/6] soc: renesas: rz-sysc: Add syscon/regmap support claudiu beznea
2025-08-19 7:54 ` Geert Uytterhoeven
2025-08-18 16:28 ` [PATCH v7 2/6] dt-bindings: thermal: r9a09g047-tsu: Document the TSU unit John Madieu
2025-08-21 0:05 ` Rob Herring
2025-08-18 16:28 ` [PATCH v7 3/6] thermal: renesas: rzg3e: Add thermal driver for the Renesas RZ/G3E SoC John Madieu
2025-08-19 7:49 ` Geert Uytterhoeven
2025-08-19 8:23 ` John Madieu
2025-08-18 16:28 ` [PATCH v7 4/6] arm64: dts: renesas: r9a09g047: Add #address-cells property in sys node John Madieu
2025-08-19 7:44 ` Geert Uytterhoeven
2025-08-19 8:25 ` John Madieu
2025-08-18 16:28 ` [PATCH v7 5/6] arm64: dts: renesas: r9a09g047: Add TSU node John Madieu
2025-08-18 16:28 ` [PATCH v7 6/6] arm64: defconfig: Enable the Renesas RZ/G3E thermal driver John Madieu
2025-08-18 18:24 ` [PATCH v7 0/6] thermal: renesas: Add support for RZ/G3E Rob Herring (Arm)
2025-08-19 8:49 ` John Madieu
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20250818162859.9661-2-john.madieu.xa@bp.renesas.com \
--to=john.madieu.xa@bp.renesas.com \
--cc=biju.das.jz@bp.renesas.com \
--cc=catalin.marinas@arm.com \
--cc=claudiu.beznea.uj@bp.renesas.com \
--cc=conor+dt@kernel.org \
--cc=daniel.lezcano@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=geert+renesas@glider.be \
--cc=john.madieu@gmail.com \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pm@vger.kernel.org \
--cc=linux-renesas-soc@vger.kernel.org \
--cc=lukasz.luba@arm.com \
--cc=magnus.damm@gmail.com \
--cc=mturquette@baylibre.com \
--cc=p.zabel@pengutronix.de \
--cc=rafael@kernel.org \
--cc=robh@kernel.org \
--cc=rui.zhang@intel.com \
--cc=sboyd@kernel.org \
--cc=will@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).