From: Michael Walle <mwalle@kernel.org>
To: Nishanth Menon <nm@ti.com>, Vignesh Raghavendra <vigneshr@ti.com>,
Tero Kristo <kristo@kernel.org>, Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
Michael Walle <mwalle@kernel.org>,
Jean Delvare <jdelvare@suse.com>,
Guenter Roeck <linux@roeck-us.net>, Lee Jones <lee@kernel.org>,
Srinivas Kandagatla <srini@kernel.org>,
Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, linux-hwmon@vger.kernel.org,
linux-watchdog@vger.kernel.org
Subject: [PATCH v1 0/7] Initial Kontron SMARC-sAM67 support
Date: Fri, 22 Aug 2025 15:15:24 +0200 [thread overview]
Message-ID: <20250822131531.1366437-1-mwalle@kernel.org> (raw)
Now that the PMIC support is there, we can finally, upstream the
support for this board. Besides the usual device tree, this
patchset contains the support for the on-board house keeping MCU. It
make extensive reuse of the drivers for the former SMARC-sAL28
board. Besides different hwmon sensors, all the dt binding patches
will just add a board specific compatible (in addition to the old
sl28 compatible) to make any future board specific quirks possible.
I'm aware that there is a patch [1] which moves the sl28cpld MFD
schema to a different directory. Once that patch is merged, I'll
repost this series. But I already want to get some early feedback.
[1] https://lore.kernel.org/r/20250822075712.27314-2-krzysztof.kozlowski@linaro.org/
Michael Walle (7):
dt-bindings: arm: ti: Add bindings for Kontron SMARC-sAM67 module
dt-bindings: mfd: sl28cpld: add sa67mcu compatible
dt-bindings: hwmon: sl28cpld: add sa67mcu compatible
dt-bindings: watchdog: add SMARC-sAM67 support
dt-bindings: nvmem: sl28cpld: add sa67mcu compatible
hwmon: sl28cpld: add SMARC-sAM67 support
arm64: dts: ti: Add support for Kontron SMARC-sAM67
.../devicetree/bindings/arm/ti/k3.yaml | 1 +
.../hwmon/kontron,sl28cpld-hwmon.yaml | 1 +
.../bindings/mfd/kontron,sl28cpld.yaml | 7 +-
.../nvmem/layouts/kontron,sl28-vpd.yaml | 7 +-
.../watchdog/kontron,sl28cpld-wdt.yaml | 7 +-
arch/arm64/boot/dts/ti/Makefile | 6 +
.../dts/ti/k3-am67a-kontron-sa67-base.dts | 1092 +++++++++++++++++
.../dts/ti/k3-am67a-kontron-sa67-gbe1.dtso | 19 +
.../ti/k3-am67a-kontron-sa67-rtc-rv8263.dtso | 24 +
drivers/hwmon/sl28cpld-hwmon.c | 76 +-
10 files changed, 1234 insertions(+), 6 deletions(-)
create mode 100644 arch/arm64/boot/dts/ti/k3-am67a-kontron-sa67-base.dts
create mode 100644 arch/arm64/boot/dts/ti/k3-am67a-kontron-sa67-gbe1.dtso
create mode 100644 arch/arm64/boot/dts/ti/k3-am67a-kontron-sa67-rtc-rv8263.dtso
--
2.39.5
next reply other threads:[~2025-08-23 6:30 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-08-22 13:15 Michael Walle [this message]
2025-08-22 13:15 ` [PATCH v1 1/7] dt-bindings: arm: ti: Add bindings for Kontron SMARC-sAM67 module Michael Walle
2025-08-25 7:43 ` Krzysztof Kozlowski
2025-08-22 13:15 ` [PATCH v1 2/7] dt-bindings: mfd: sl28cpld: add sa67mcu compatible Michael Walle
2025-08-27 12:56 ` Krzysztof Kozlowski
2025-08-22 13:15 ` [PATCH v1 3/7] dt-bindings: hwmon: " Michael Walle
2025-08-27 12:56 ` Krzysztof Kozlowski
2025-08-22 13:15 ` [PATCH v1 4/7] dt-bindings: watchdog: add SMARC-sAM67 support Michael Walle
2025-08-27 13:03 ` Krzysztof Kozlowski
2025-08-22 13:15 ` [PATCH v1 5/7] dt-bindings: nvmem: sl28cpld: add sa67mcu compatible Michael Walle
2025-08-27 12:57 ` Krzysztof Kozlowski
2025-08-22 13:15 ` [PATCH v1 6/7] hwmon: sl28cpld: add SMARC-sAM67 support Michael Walle
2025-08-22 13:15 ` [PATCH v1 7/7] arm64: dts: ti: Add support for Kontron SMARC-sAM67 Michael Walle
2025-08-27 13:31 ` Andrew Davis
2025-08-22 15:23 ` [PATCH v1 0/7] Initial Kontron SMARC-sAM67 support Nishanth Menon
2025-08-25 7:28 ` Michael Walle
2025-08-27 12:18 ` Michael Walle
2025-08-22 21:27 ` Rob Herring (Arm)
2025-08-25 7:53 ` Michael Walle
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20250822131531.1366437-1-mwalle@kernel.org \
--to=mwalle@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=jdelvare@suse.com \
--cc=kristo@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=lee@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-hwmon@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-watchdog@vger.kernel.org \
--cc=linux@roeck-us.net \
--cc=nm@ti.com \
--cc=robh@kernel.org \
--cc=srini@kernel.org \
--cc=vigneshr@ti.com \
--cc=wim@linux-watchdog.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).