public inbox for linux-arm-kernel@lists.infradead.org
 help / color / mirror / Atom feed
From: Nishanth Menon <nm@ti.com>
To: Paresh Bhagat <p-bhagat@ti.com>
Cc: <vigneshr@ti.com>, <praneeth@ti.com>, <kristo@kernel.org>,
	<robh@kernel.org>, <krzk+dt@kernel.org>, <conor+dt@kernel.org>,
	<linux-arm-kernel@lists.infradead.org>,
	<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
	<khasim@ti.com>, <v-singh1@ti.com>, <afd@ti.com>, <bb@ti.com>,
	<s-k6@ti.com>
Subject: Re: [PATCH] arm64: dts: ti: k3-am62d2-evm: Add support for OSPI flash
Date: Fri, 22 Aug 2025 13:30:14 -0500	[thread overview]
Message-ID: <20250822183014.apyvqws4afiqiymb@specks> (raw)
In-Reply-To: <20250813090300.733295-1-p-bhagat@ti.com>

On 14:33-20250813, Paresh Bhagat wrote:
> AM62D2 EVM has S28HS512T 64 MiB Octal SPI NOR flash connected to the
> OSPI interface. Add support for the flash and describe the partition
> information as per bootloader.
> 
> Signed-off-by: Paresh Bhagat <p-bhagat@ti.com>
> ---
> Boot logs
> https://gist.github.com/paresh-bhagat12/262d8c64e692d22c4e48363d246fb083

We already have issues with am62d that needs fixing:
cpu cpu0: _of_add_opp_table_v2: no supported OPPs
cpu cpu0: OPP table can't be empty

and

Please enable defconfig for this device
arch/arm64/boot/dts/ti/k3-am62d2-evm.dts:       typec_pd0: usb-power-controller@3f {

We can look at adding features for am62d after the above are done.
> 
> Tech Ref Manual-https://www.ti.com/lit/pdf/sprujd4
> Schematics Link-https://www.ti.com/lit/zip/sprcal5
> 
>  arch/arm64/boot/dts/ti/k3-am62d2-evm.dts | 86 ++++++++++++++++++++++++
>  1 file changed, 86 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-am62d2-evm.dts b/arch/arm64/boot/dts/ti/k3-am62d2-evm.dts
> index daea18b0bc61..aa943ef52fb5 100644
> --- a/arch/arm64/boot/dts/ti/k3-am62d2-evm.dts
> +++ b/arch/arm64/boot/dts/ti/k3-am62d2-evm.dts
> @@ -25,6 +25,7 @@ aliases {
>  		rtc0 = &wkup_rtc0;
>  		ethernet0 = &cpsw_port1;
>  		ethernet1 = &cpsw_port2;
> +		spi0 = &ospi0;
>  	};
>  
>  	chosen {
> @@ -367,6 +368,26 @@ usr_led_pins_default: usr-led-default-pins {
>  			AM62DX_IOPAD(0x0244, PIN_INPUT, 7) /* (D18) MMC1_SDWP.GPIO1_49 */
>  		>;
>  	};
> +
> +	ospi0_pins_default: ospi0-default-pins {
> +		pinctrl-single,pins = <
> +			AM62DX_IOPAD(0x0000, PIN_OUTPUT, 0) /* (L22) OSPI0_CLK */
> +			AM62DX_IOPAD(0x002c, PIN_OUTPUT, 0) /* (H21) OSPI0_CSn0 */
> +			AM62DX_IOPAD(0x0030, PIN_OUTPUT, 0) /* (G19) OSPI0_CSn1 */
> +			AM62DX_IOPAD(0x0034, PIN_OUTPUT, 0) /* (K20) OSPI0_CSn2 */
> +			AM62DX_IOPAD(0x0038, PIN_OUTPUT, 0) /* (G20) OSPI0_CSn3 */
> +			AM62DX_IOPAD(0x000c, PIN_INPUT, 0) /* (J21) OSPI0_D0 */
> +			AM62DX_IOPAD(0x0010, PIN_INPUT, 0) /* (J18) OSPI0_D1 */
> +			AM62DX_IOPAD(0x0014, PIN_INPUT, 0) /* (J19) OSPI0_D2 */
> +			AM62DX_IOPAD(0x0018, PIN_INPUT, 0) /* (H18) OSPI0_D3 */
> +			AM62DX_IOPAD(0x001c, PIN_INPUT, 0) /* (K21) OSPI0_D4 */
> +			AM62DX_IOPAD(0x0020, PIN_INPUT, 0) /* (H19) OSPI0_D5 */
> +			AM62DX_IOPAD(0x0024, PIN_INPUT, 0) /* (J20) OSPI0_D6 */
> +			AM62DX_IOPAD(0x0028, PIN_INPUT, 0) /* (J22) OSPI0_D7 */
> +			AM62DX_IOPAD(0x0008, PIN_INPUT, 0) /* (L21) OSPI0_DQS */
> +		>;
> +		bootph-all;
> +	};
>  };
>  
>  &mcu_gpio0 {
> @@ -613,3 +634,68 @@ &c7x_0 {
>  &main_rti4 {
>  	status = "reserved";
>  };
> +
> +&fss {
> +	status = "okay";
> +};
> +
> +&ospi0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&ospi0_pins_default>;
> +	status = "okay";
> +
> +	flash@0{
> +		compatible = "jedec,spi-nor";
> +		reg = <0x0>;
> +		spi-tx-bus-width = <8>;
> +		spi-rx-bus-width = <8>;
> +		spi-max-frequency = <25000000>;
> +		cdns,tshsl-ns = <60>;
> +		cdns,tsd2d-ns = <60>;
> +		cdns,tchsh-ns = <60>;
> +		cdns,tslch-ns = <60>;
> +		cdns,read-delay = <4>;
> +
> +		partitions {
> +			compatible = "fixed-partitions";
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +
> +			partition@0 {
> +				label = "ospi.tiboot3";
> +				reg = <0x0 0x80000>;
> +			};
> +
> +			partition@80000 {
> +				label = "ospi.tispl";
> +				reg = <0x80000 0x200000>;
> +			};
> +
> +			partition@280000 {
> +				label = "ospi.u-boot";
> +				reg = <0x280000 0x400000>;
> +			};
> +
> +			partition@680000 {
> +				label = "ospi.env";
> +				reg = <0x680000 0x40000>;
> +			};
> +
> +			partition@6c0000 {
> +				label = "ospi.env.backup";
> +				reg = <0x6c0000 0x40000>;
> +			};
> +
> +			partition@800000 {
> +				label = "ospi.rootfs";
> +				reg = <0x800000 0x37c0000>;
> +			};
> +
> +			partition@3fc0000 {
> +				label = "ospi.phypattern";
> +				reg = <0x3fc0000 0x40000>;
> +				bootph-all;
> +			};
> +		};
> +	};
> +};
> -- 
> 2.34.1
> 
> 

-- 
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3  1A34 DDB5 849D 1736 249D
https://ti.com/opensource


  reply	other threads:[~2025-08-23  6:42 UTC|newest]

Thread overview: 5+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2025-08-13  9:03 [PATCH] arm64: dts: ti: k3-am62d2-evm: Add support for OSPI flash Paresh Bhagat
2025-08-22 18:30 ` Nishanth Menon [this message]
2025-08-23  3:33   ` Paresh Bhagat
2025-09-02  8:33     ` Santhosh Kumar K
2025-09-12  9:50 ` Nishanth Menon

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20250822183014.apyvqws4afiqiymb@specks \
    --to=nm@ti.com \
    --cc=afd@ti.com \
    --cc=bb@ti.com \
    --cc=conor+dt@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=khasim@ti.com \
    --cc=kristo@kernel.org \
    --cc=krzk+dt@kernel.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=p-bhagat@ti.com \
    --cc=praneeth@ti.com \
    --cc=robh@kernel.org \
    --cc=s-k6@ti.com \
    --cc=v-singh1@ti.com \
    --cc=vigneshr@ti.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox