linux-arm-kernel.lists.infradead.org archive mirror
 help / color / mirror / Atom feed
From: Beleswar Padhi <b-padhi@ti.com>
To: <nm@ti.com>, <vigneshr@ti.com>, <kristo@kernel.org>,
	<robh@kernel.org>, <krzk+dt@kernel.org>, <conor+dt@kernel.org>
Cc: <afd@ti.com>, <u-kumar1@ti.com>, <hnagalla@ti.com>, <jm@ti.com>,
	<b-padhi@ti.com>, <devicetree@vger.kernel.org>,
	<linux-kernel@vger.kernel.org>,
	<linux-arm-kernel@lists.infradead.org>,
	Josua Mayer <josua@solid-run.com>,
	Logan Bristol <logan.bristol@utexas.edu>,
	Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Subject: [PATCH v2 17/33] arm64: dts: ti: k3-am642-sr-som: Add missing cfg for TI IPC Firmware
Date: Sat, 23 Aug 2025 21:38:45 +0530	[thread overview]
Message-ID: <20250823160901.2177841-18-b-padhi@ti.com> (raw)
In-Reply-To: <20250823160901.2177841-1-b-padhi@ti.com>

Currently, only R5F remote processors are enabled for k3-am642-sr SoMs,
whereas the M4F in MCU domain is disabled. Enable the M4F remote
processor at board level by reserving memory carveouts and assigning
mailboxes.

While at it, reserve the MAIN domain timers that are used by R5F remote
processors for ticks to avoid rproc crashes. This config aligns with
other AM64 boards and can be refactored out later.

Signed-off-by: Beleswar Padhi <b-padhi@ti.com>
---
Cc: Josua Mayer <josua@solid-run.com>
Cc: Logan Bristol <logan.bristol@utexas.edu>
Cc: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Requesting for review/test of this patch.

v2: Changelog:
1. Re-ordered patch from [PATCH 27/33] to [PATCH v2 17/33].

Link to v1:
https://lore.kernel.org/all/20250814223839.3256046-28-b-padhi@ti.com/

 arch/arm64/boot/dts/ti/k3-am642-sr-som.dtsi | 54 +++++++++++++++++++++
 1 file changed, 54 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am642-sr-som.dtsi b/arch/arm64/boot/dts/ti/k3-am642-sr-som.dtsi
index 81adae0a8e55..8cb61f831734 100644
--- a/arch/arm64/boot/dts/ti/k3-am642-sr-som.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am642-sr-som.dtsi
@@ -162,6 +162,24 @@ main_r5fss1_core1_memory_region: r5f-memory@a3100000 {
 			reg = <0x00 0xa3100000 0x00 0xf00000>;
 			no-map;
 		};
+
+		mcu_m4fss_dma_memory_region: m4f-dma-memory@a4000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa4000000 0x00 0x100000>;
+			no-map;
+		};
+
+		mcu_m4fss_memory_region: m4f-memory@a4100000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa4100000 0x00 0xf00000>;
+			no-map;
+		};
+
+		rtos_ipc_memory_region: ipc-memories@a5000000 {
+			reg = <0x00 0xa5000000 0x00 0x00800000>;
+			alignment = <0x1000>;
+			no-map;
+		};
 	};
 
 	vdd_mmc0: regulator-vdd-mmc0 {
@@ -291,6 +309,35 @@ mbox_main_r5fss1_core1: mbox-main-r5fss1-core1 {
 	};
 };
 
+&mailbox0_cluster6 {
+	status = "okay";
+
+	mbox_m4_0: mbox-m4-0 {
+		ti,mbox-rx = <0 0 2>;
+		ti,mbox-tx = <1 0 2>;
+	};
+};
+
+/* main_timer8 is used by r5f0-0 */
+&main_timer8 {
+	status = "reserved";
+};
+
+/* main_timer9 is used by r5f0-1 */
+&main_timer9 {
+	status = "reserved";
+};
+
+/* main_timer10 is used by r5f1-0 */
+&main_timer10 {
+	status = "reserved";
+};
+
+/* main_timer11 is used by r5f1-1 */
+&main_timer11 {
+	status = "reserved";
+};
+
 &main_i2c0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_i2c0_default_pins>;
@@ -524,6 +571,13 @@ &main_r5fss1_core1 {
 	status = "okay";
 };
 
+&mcu_m4fss {
+	mboxes = <&mailbox0_cluster6 &mbox_m4_0>;
+	memory-region = <&mcu_m4fss_dma_memory_region>,
+			<&mcu_m4fss_memory_region>;
+	status = "okay";
+};
+
 /* SoC default UART console */
 &main_uart0 {
 	pinctrl-names = "default";
-- 
2.34.1



  parent reply	other threads:[~2025-08-23 17:56 UTC|newest]

Thread overview: 41+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2025-08-23 16:08 [PATCH v2 00/33] Refactor TI IPC DT configs into dtsi Beleswar Padhi
2025-08-23 16:08 ` [PATCH v2 01/33] arm64: dts: ti: k3-j7200: Enable remote processors at board level Beleswar Padhi
2025-08-25 14:18   ` Andrew Davis
2025-08-23 16:08 ` [PATCH v2 02/33] arm64: dts: ti: k3-j721e: " Beleswar Padhi
2025-08-23 16:08 ` [PATCH v2 03/33] arm64: dts: ti: k3-j721s2: " Beleswar Padhi
2025-08-23 16:08 ` [PATCH v2 04/33] arm64: dts: ti: k3-j784s4-j742s2: " Beleswar Padhi
2025-08-23 16:08 ` [PATCH v2 05/33] arm64: dts: ti: k3-am62p-j722s: " Beleswar Padhi
2025-08-23 16:08 ` [PATCH v2 06/33] arm64: dts: ti: k3-am62: " Beleswar Padhi
2025-08-28 11:43   ` Wadim Egorov
2025-08-23 16:08 ` [PATCH v2 07/33] arm64: dts: ti: k3-am62a: " Beleswar Padhi
2025-08-23 16:08 ` [PATCH v2 08/33] arm64: dts: ti: k3-am64: " Beleswar Padhi
2025-08-28 11:46   ` Wadim Egorov
2025-08-23 16:08 ` [PATCH v2 09/33] arm64: dts: ti: k3-am65: " Beleswar Padhi
2025-08-23 16:08 ` [PATCH v2 10/33] arm64: dts: ti: k3-am62: Enable Mailbox nodes at the " Beleswar Padhi
2025-08-23 16:08 ` [PATCH v2 11/33] arm64: dts: ti: k3-am62a: " Beleswar Padhi
2025-08-23 16:08 ` [PATCH v2 12/33] arm64: dts: ti: k3-am6*-boards: Add label to reserved-memory node Beleswar Padhi
2025-08-23 16:08 ` [PATCH v2 13/33] arm64: dts: ti: k3-j721e-beagleboneai64: Add missing cfg for TI IPC FW Beleswar Padhi
2025-08-23 16:08 ` [PATCH v2 14/33] arm64: dts: ti: k3-am62p-verdin: Add missing cfg for TI IPC Firmware Beleswar Padhi
2025-08-23 16:08 ` [PATCH v2 15/33] arm64: dts: ti: k3-am62-verdin: " Beleswar Padhi
2025-08-23 16:08 ` [PATCH v2 16/33] arm64: dts: ti: k3-am62-pocketbeagle2: " Beleswar Padhi
2025-08-23 16:08 ` Beleswar Padhi [this message]
2025-08-23 16:08 ` [PATCH v2 18/33] arm64: dts: ti: k3-am64-phycore-som: " Beleswar Padhi
2025-08-28 11:42   ` Wadim Egorov
2025-08-29  6:02     ` Beleswar Prasad Padhi
2025-08-23 16:08 ` [PATCH v2 19/33] arm64: dts: ti: k3-am642-tqma64xxl: " Beleswar Padhi
2025-08-23 16:08 ` [PATCH v2 20/33] Revert "arm64: dts: ti: k3-j721e-sk: Fix reversed C6x carveout locations" Beleswar Padhi
2025-08-23 16:08 ` [PATCH v2 21/33] Revert "arm64: dts: ti: k3-j721e-beagleboneai64: " Beleswar Padhi
2025-08-23 16:08 ` [PATCH v2 22/33] arm64: dts: ti: k3-j721e-beagleboneai64: Switch MAIN R5F clusters to Split-mode Beleswar Padhi
2025-08-23 16:08 ` [PATCH v2 23/33] arm64: dts: ti: k3-j7200-ti-ipc-firmware: Refactor IPC cfg into new dtsi Beleswar Padhi
2025-08-23 16:08 ` [PATCH v2 24/33] arm64: dts: ti: k3-j721e-ti-ipc-firmware: " Beleswar Padhi
2025-08-23 16:08 ` [PATCH v2 25/33] arm64: dts: ti: k3-j721s2-ti-ipc-firmware: " Beleswar Padhi
2025-08-23 16:08 ` [PATCH v2 26/33] arm64: dts: ti: k3-j784s4-j742s2-ti-ipc-firmware-common: " Beleswar Padhi
2025-08-23 16:08 ` [PATCH v2 27/33] arm64: dts: ti: k3-j784s4-ti-ipc-firmware: " Beleswar Padhi
2025-08-23 16:08 ` [PATCH v2 28/33] arm64: dts: ti: k3-j722s-ti-ipc-firmware: " Beleswar Padhi
2025-08-23 16:08 ` [PATCH v2 29/33] arm64: dts: ti: k3-am62p-ti-ipc-firmware: " Beleswar Padhi
2025-08-23 16:08 ` [PATCH v2 30/33] arm64: dts: ti: k3-am62-ti-ipc-firmware: " Beleswar Padhi
2025-08-28 11:51   ` Wadim Egorov
2025-08-23 16:08 ` [PATCH v2 31/33] arm64: dts: ti: k3-am62a-ti-ipc-firmware: " Beleswar Padhi
2025-08-23 16:09 ` [PATCH v2 32/33] arm64: dts: ti: k3-am64-ti-ipc-firmware: " Beleswar Padhi
2025-08-28 11:52   ` Wadim Egorov
2025-08-23 16:09 ` [PATCH v2 33/33] arm64: dts: ti: k3-am65-ti-ipc-firmware: " Beleswar Padhi

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20250823160901.2177841-18-b-padhi@ti.com \
    --to=b-padhi@ti.com \
    --cc=afd@ti.com \
    --cc=conor+dt@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=hnagalla@ti.com \
    --cc=jm@ti.com \
    --cc=josua@solid-run.com \
    --cc=kristo@kernel.org \
    --cc=krzk+dt@kernel.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=logan.bristol@utexas.edu \
    --cc=matthias.schiffer@ew.tq-group.com \
    --cc=nm@ti.com \
    --cc=robh@kernel.org \
    --cc=u-kumar1@ti.com \
    --cc=vigneshr@ti.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).