From: Vikram Sharma <quic_vikramsa@quicinc.com>
To: <bryan.odonoghue@linaro.org>, <mchehab@kernel.org>,
<robh@kernel.org>, <krzk+dt@kernel.org>, <conor+dt@kernel.org>,
<andersson@kernel.org>, <konradybcio@kernel.org>,
<hverkuil-cisco@xs4all.nl>, <cros-qcom-dts-watchers@chromium.org>,
<catalin.marinas@arm.com>, <will@kernel.org>
Cc: <linux-arm-kernel@lists.infradead.org>,
<quic_svankada@quicinc.com>, <linux-media@vger.kernel.org>,
<linux-arm-msm@vger.kernel.org>, <devicetree@vger.kernel.org>,
<linux-kernel@vger.kernel.org>,
Ravi Shankar <quic_rshankar@quicinc.com>,
Vishal Verma <quic_vishverm@quicinc.com>
Subject: [PATCH 2/4] arm64: dts: qcom: qcs8300: Add CCI definitions
Date: Tue, 9 Sep 2025 17:12:39 +0530 [thread overview]
Message-ID: <20250909114241.840842-3-quic_vikramsa@quicinc.com> (raw)
In-Reply-To: <20250909114241.840842-1-quic_vikramsa@quicinc.com>
From: Nihal Kumar Gupta <quic_nihalkum@quicinc.com>
Add support for three Camera Control Interface (CCI) controllers
on the Qualcomm QCS8300 SoC. Configure clocks, power domains,
pinctrl states and two I2C buses (i2c0, i2c1) with 1 MHz frequency.
Nodes are added in a disabled state by default.
Co-developed-by: Ravi Shankar <quic_rshankar@quicinc.com>
Signed-off-by: Ravi Shankar <quic_rshankar@quicinc.com>
Co-developed-by: Vishal Verma <quic_vishverm@quicinc.com>
Signed-off-by: Vishal Verma <quic_vishverm@quicinc.com>
Co-developed-by: Suresh Vankadara <quic_svankada@quicinc.com>
Signed-off-by: Suresh Vankadara <quic_svankada@quicinc.com>
Signed-off-by: Nihal Kumar Gupta <quic_nihalkum@quicinc.com>
Signed-off-by: Vikram Sharma <quic_vikramsa@quicinc.com>
---
arch/arm64/boot/dts/qcom/qcs8300.dtsi | 309 ++++++++++++++++++++++++++
1 file changed, 309 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/qcs8300.dtsi b/arch/arm64/boot/dts/qcom/qcs8300.dtsi
index a248e269d72d..a69719e291ea 100644
--- a/arch/arm64/boot/dts/qcom/qcs8300.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcs8300.dtsi
@@ -4681,6 +4681,123 @@ videocc: clock-controller@abf0000 {
#power-domain-cells = <1>;
};
+ cci0: cci@ac13000 {
+ compatible = "qcom,qcs8300-cci", "qcom,msm8996-cci";
+ reg = <0x0 0x0ac13000 0x0 0x1000>;
+
+ interrupts = <GIC_SPI 460 IRQ_TYPE_EDGE_RISING>;
+
+ clocks = <&camcc CAM_CC_CAMNOC_AXI_CLK>,
+ <&camcc CAM_CC_CPAS_AHB_CLK>,
+ <&camcc CAM_CC_CCI_0_CLK>;
+ clock-names = "camnoc_axi",
+ "cpas_ahb",
+ "cci";
+
+ power-domains = <&camcc CAM_CC_TITAN_TOP_GDSC>;
+
+ pinctrl-0 = <&cci0_i2c0_default &cci0_i2c1_default>;
+ pinctrl-1 = <&cci0_i2c0_sleep &cci0_i2c1_sleep>;
+ pinctrl-names = "default", "sleep";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "disabled";
+
+ cci0_i2c0: i2c-bus@0 {
+ reg = <0>;
+ clock-frequency = <1000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ cci0_i2c1: i2c-bus@1 {
+ reg = <1>;
+ clock-frequency = <1000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
+ cci1: cci@ac14000 {
+ compatible = "qcom,qcs8300-cci", "qcom,msm8996-cci";
+ reg = <0x0 0x0ac14000 0x0 0x1000>;
+
+ interrupts = <GIC_SPI 271 IRQ_TYPE_EDGE_RISING>;
+
+ clocks = <&camcc CAM_CC_CAMNOC_AXI_CLK>,
+ <&camcc CAM_CC_CPAS_AHB_CLK>,
+ <&camcc CAM_CC_CCI_1_CLK>;
+ clock-names = "camnoc_axi",
+ "cpas_ahb",
+ "cci";
+
+ power-domains = <&camcc CAM_CC_TITAN_TOP_GDSC>;
+
+ pinctrl-0 = <&cci1_i2c0_default &cci1_i2c1_default>;
+ pinctrl-1 = <&cci1_i2c0_sleep &cci1_i2c1_sleep>;
+ pinctrl-names = "default", "sleep";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "disabled";
+
+ cci1_i2c0: i2c-bus@0 {
+ reg = <0>;
+ clock-frequency = <1000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ cci1_i2c1: i2c-bus@1 {
+ reg = <1>;
+ clock-frequency = <1000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
+ cci2: cci@ac15000 {
+ compatible = "qcom,qcs8300-cci", "qcom,msm8996-cci";
+ reg = <0x0 0x0ac15000 0x0 0x1000>;
+
+ interrupts = <GIC_SPI 651 IRQ_TYPE_EDGE_RISING>;
+
+ clocks = <&camcc CAM_CC_CAMNOC_AXI_CLK>,
+ <&camcc CAM_CC_CPAS_AHB_CLK>,
+ <&camcc CAM_CC_CCI_2_CLK>;
+ clock-names = "camnoc_axi",
+ "cpas_ahb",
+ "cci";
+
+ power-domains = <&camcc CAM_CC_TITAN_TOP_GDSC>;
+
+ pinctrl-0 = <&cci2_i2c0_default &cci2_i2c1_default>;
+ pinctrl-1 = <&cci2_i2c0_sleep &cci2_i2c1_sleep>;
+ pinctrl-names = "default", "sleep";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "disabled";
+
+ cci2_i2c0: i2c-bus@0 {
+ reg = <0>;
+ clock-frequency = <1000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ cci2_i2c1: i2c-bus@1 {
+ reg = <1>;
+ clock-frequency = <1000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
camss: isp@ac78000 {
compatible = "qcom,qcs8300-camss";
@@ -4975,6 +5092,198 @@ tlmm: pinctrl@f100000 {
#interrupt-cells = <2>;
wakeup-parent = <&pdc>;
+ cci0_i2c0_default: cci0-0-default-state {
+ sda-pins {
+ pins = "gpio57";
+ function = "cci_i2c_sda";
+ drive-strength = <2>;
+ bias-pull-up = <2200>;
+ };
+
+ scl-pins {
+ pins = "gpio58";
+ function = "cci_i2c_scl";
+ drive-strength = <2>;
+ bias-pull-up = <2200>;
+ };
+ };
+
+ cci0_i2c0_sleep: cci0-0-sleep-state {
+ sda-pins {
+ pins = "gpio57";
+ function = "cci_i2c_sda";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ scl-pins {
+ pins = "gpio58";
+ function = "cci_i2c_scl";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+ };
+
+ cci0_i2c1_default: cci0-1-default-state {
+ sda-pins {
+ pins = "gpio29";
+ function = "cci_i2c_sda";
+ drive-strength = <2>;
+ bias-pull-up = <2200>;
+ };
+
+ scl-pins {
+ pins = "gpio30";
+ function = "cci_i2c_scl";
+ drive-strength = <2>;
+ bias-pull-up = <2200>;
+ };
+ };
+
+ cci0_i2c1_sleep: cci0-1-sleep-state {
+ sda-pins {
+ pins = "gpio29";
+ function = "cci_i2c_sda";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ scl-pins {
+ pins = "gpio30";
+ function = "cci_i2c_scl";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+ };
+
+ cci1_i2c0_default: cci1-0-default-state {
+ sda-pins {
+ pins = "gpio59";
+ function = "cci_i2c_sda";
+ drive-strength = <2>;
+ bias-pull-up = <2200>;
+ };
+
+ scl-pins {
+ pins = "gpio60";
+ function = "cci_i2c_scl";
+ drive-strength = <2>;
+ bias-pull-up = <2200>;
+ };
+ };
+
+ cci1_i2c0_sleep: cci1-0-sleep-state {
+ sda-pins {
+ pins = "gpio59";
+ function = "cci_i2c_sda";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ scl-pins {
+ pins = "gpio60";
+ function = "cci_i2c_scl";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+ };
+
+ cci1_i2c1_default: cci1-1-default-state {
+ sda-pins {
+ pins = "gpio31";
+ function = "cci_i2c_sda";
+ drive-strength = <2>;
+ bias-pull-up = <2200>;
+ };
+
+ scl-pins {
+ pins = "gpio32";
+ function = "cci_i2c_scl";
+ drive-strength = <2>;
+ bias-pull-up = <2200>;
+ };
+ };
+
+ cci1_i2c1_sleep: cci1-1-sleep-state {
+ sda-pins {
+ pins = "gpio31";
+ function = "cci_i2c_sda";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ scl-pins {
+ pins = "gpio32";
+ function = "cci_i2c_scl";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+ };
+
+ cci2_i2c0_default: cci2-0-default-state {
+ sda-pins {
+ pins = "gpio61";
+ function = "cci_i2c_sda";
+ drive-strength = <2>;
+ bias-pull-up = <2200>;
+ };
+
+ scl-pins {
+ pins = "gpio62";
+ function = "cci_i2c_scl";
+ drive-strength = <2>;
+ bias-pull-up = <2200>;
+ };
+ };
+
+ cci2_i2c0_sleep: cci2-0-sleep-state {
+ sda-pins {
+ pins = "gpio61";
+ function = "cci_i2c_sda";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ scl-pins {
+ pins = "gpio62";
+ function = "cci_i2c_scl";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+ };
+
+ cci2_i2c1_default: cci2-1-default-state {
+ sda-pins {
+ pins = "gpio54";
+ function = "cci_i2c_sda";
+ drive-strength = <2>;
+ bias-pull-up = <2200>;
+ };
+
+ scl-pins {
+ pins = "gpio55";
+ function = "cci_i2c_scl";
+ drive-strength = <2>;
+ bias-pull-up = <2200>;
+ };
+ };
+
+ cci2_i2c1_sleep: cci2-1-sleep-state {
+ sda-pins {
+ pins = "gpio54";
+ function = "cci_i2c_sda";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ scl-pins {
+ pins = "gpio55";
+ function = "cci_i2c_scl";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+ };
+
hs0_mi2s_active: hs0-mi2s-active-state {
pins = "gpio106", "gpio107", "gpio108", "gpio109";
function = "hs0_mi2s";
--
2.25.1
next prev parent reply other threads:[~2025-09-09 17:16 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-09-09 11:42 [PATCH 0/4] Add CCI and imx577 sensor support for monaco evk Vikram Sharma
2025-09-09 11:42 ` [PATCH 1/4] dt-bindings: i2c: qcom-cci: Document qcs8300 compatible Vikram Sharma
2025-09-09 11:52 ` Bryan O'Donoghue
2025-09-09 11:42 ` Vikram Sharma [this message]
2025-10-08 10:04 ` [PATCH 2/4] arm64: dts: qcom: qcs8300: Add CCI definitions Konrad Dybcio
2025-10-10 12:32 ` Nihal Kumar Gupta
2025-09-09 11:42 ` [PATCH 3/4] arm64: dts: qcom: monaco-evk-camera: Add DT overlay Vikram Sharma
2025-09-09 14:01 ` Dmitry Baryshkov
[not found] ` <8104bb41-e827-4daa-bc96-9b6678a9d345@quicinc.com>
2025-09-11 9:19 ` Nihal Kumar Gupta
2025-09-11 10:08 ` Dmitry Baryshkov
2025-09-11 12:49 ` Nihal Kumar Gupta
2025-09-11 13:03 ` Dmitry Baryshkov
2025-09-11 13:41 ` Vikram Sharma
2025-09-11 10:57 ` Dmitry Baryshkov
2025-09-10 7:01 ` Krzysztof Kozlowski
2025-09-09 11:42 ` [PATCH 4/4] dt-bindings: media: camss: Add qcs8300 supplies binding Vikram Sharma
2025-09-09 14:00 ` Dmitry Baryshkov
2025-09-10 7:02 ` Krzysztof Kozlowski
2025-09-10 11:41 ` Bryan O'Donoghue
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20250909114241.840842-3-quic_vikramsa@quicinc.com \
--to=quic_vikramsa@quicinc.com \
--cc=andersson@kernel.org \
--cc=bryan.odonoghue@linaro.org \
--cc=catalin.marinas@arm.com \
--cc=conor+dt@kernel.org \
--cc=cros-qcom-dts-watchers@chromium.org \
--cc=devicetree@vger.kernel.org \
--cc=hverkuil-cisco@xs4all.nl \
--cc=konradybcio@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-media@vger.kernel.org \
--cc=mchehab@kernel.org \
--cc=quic_rshankar@quicinc.com \
--cc=quic_svankada@quicinc.com \
--cc=quic_vishverm@quicinc.com \
--cc=robh@kernel.org \
--cc=will@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox