[PATCH v4 0/5] PCI: mediatek: add support AN7583 + YAML rework

[PATCH v4 0/5] PCI: mediatek: add support AN7583 + YAML rework

[Christian Marangi]

This little series convert the PCIe GEN2 Documentation to YAML schema
and adds support for Airoha AN7583 GEN2 PCIe Controller.

Changes v4:
- Additional fix/improvement for YAML conversion
- Add review tag
- Fix wording on hifsys patch
- Rework PCI driver to flags and improve PBus logic
Changes v3:
- Rework patch 1 to drop syscon compatible
Changes v2:
- Add cover letter
- Describe skip_pcie_rstb variable
- Fix hifsys schema (missing syscon)
- Address comments on the YAML schema for PCIe GEN2
- Keep alphabetical order for AN7583

Christian Marangi (5):
  ARM: dts: mediatek: drop wrong syscon hifsys compatible for
    MT2701/7623
  dt-bindings: PCI: mediatek: Convert to YAML schema
  dt-bindings: PCI: mediatek: Add support for Airoha AN7583
  PCI: mediatek: convert bool to single flags entry and bitmap
  PCI: mediatek: add support for Airoha AN7583 SoC

 .../bindings/pci/mediatek-pcie-mt7623.yaml    | 164 +++++++
 .../devicetree/bindings/pci/mediatek-pcie.txt | 289 ------------
 .../bindings/pci/mediatek-pcie.yaml           | 428 ++++++++++++++++++
 arch/arm/boot/dts/mediatek/mt2701.dtsi        |   2 +-
 arch/arm/boot/dts/mediatek/mt7623.dtsi        |   3 +-
 drivers/pci/controller/pcie-mediatek.c        | 120 +++--
 6 files changed, 680 insertions(+), 326 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/pci/mediatek-pcie-mt7623.yaml
 delete mode 100644 Documentation/devicetree/bindings/pci/mediatek-pcie.txt
 create mode 100644 Documentation/devicetree/bindings/pci/mediatek-pcie.yaml

-- 
2.51.0

[PATCH v4 1/5] ARM: dts: mediatek: drop wrong syscon hifsys compatible for MT2701/7623

[Christian Marangi]

The syscon compatible for the hifsys node for Mediatek MT2701/MT7623 SoC
was wrongly added following the pattern of other clock node but it's
actually not needed as the register are not used by other device on the
SoC.

On top of this it's against the schema for hifsys YAML and causes a
dtbs_check warning.

Drop the "syscon" compatible to mute the warning and reflect the
compatible property described in the mediatek,mt2701-hifsys.yaml schema.

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
---
 arch/arm/boot/dts/mediatek/mt2701.dtsi | 2 +-
 arch/arm/boot/dts/mediatek/mt7623.dtsi | 3 +--
 2 files changed, 2 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/mediatek/mt2701.dtsi b/arch/arm/boot/dts/mediatek/mt2701.dtsi
index ce6a4015fed5..128b87229f3d 100644
--- a/arch/arm/boot/dts/mediatek/mt2701.dtsi
+++ b/arch/arm/boot/dts/mediatek/mt2701.dtsi
@@ -597,7 +597,7 @@ larb1: larb@16010000 {
 	};
 
 	hifsys: syscon@1a000000 {
-		compatible = "mediatek,mt2701-hifsys", "syscon";
+		compatible = "mediatek,mt2701-hifsys";
 		reg = <0 0x1a000000 0 0x1000>;
 		#clock-cells = <1>;
 		#reset-cells = <1>;
diff --git a/arch/arm/boot/dts/mediatek/mt7623.dtsi b/arch/arm/boot/dts/mediatek/mt7623.dtsi
index fd7a89cc337d..4b1685b93989 100644
--- a/arch/arm/boot/dts/mediatek/mt7623.dtsi
+++ b/arch/arm/boot/dts/mediatek/mt7623.dtsi
@@ -744,8 +744,7 @@ vdecsys: syscon@16000000 {
 
 	hifsys: syscon@1a000000 {
 		compatible = "mediatek,mt7623-hifsys",
-			     "mediatek,mt2701-hifsys",
-			     "syscon";
+			     "mediatek,mt2701-hifsys";
 		reg = <0 0x1a000000 0 0x1000>;
 		#clock-cells = <1>;
 		#reset-cells = <1>;
-- 
2.51.0

[PATCH v4 2/5] dt-bindings: PCI: mediatek: Convert to YAML schema

[Christian Marangi]

Convert the PCI mediatek Documentation to YAML schema to enable
validation of the supported GEN1/2 Mediatek PCIe controller.

While converting, lots of cleanup were done from the .txt with better
specifying what is supported by the various PCIe controller variant and
drop of redundant info that are part of the standard PCIe Host Bridge
schema.

To reduce schema complexity the .txt is split in 2 YAML, one for
mt7623/mt2701 and the other for every other compatible.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
---
 .../bindings/pci/mediatek-pcie-mt7623.yaml    | 164 +++++++++
 .../devicetree/bindings/pci/mediatek-pcie.txt | 289 ----------------
 .../bindings/pci/mediatek-pcie.yaml           | 318 ++++++++++++++++++
 3 files changed, 482 insertions(+), 289 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/pci/mediatek-pcie-mt7623.yaml
 delete mode 100644 Documentation/devicetree/bindings/pci/mediatek-pcie.txt
 create mode 100644 Documentation/devicetree/bindings/pci/mediatek-pcie.yaml

diff --git a/Documentation/devicetree/bindings/pci/mediatek-pcie-mt7623.yaml b/Documentation/devicetree/bindings/pci/mediatek-pcie-mt7623.yaml
new file mode 100644
index 000000000000..e33bcc216e30
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/mediatek-pcie-mt7623.yaml
@@ -0,0 +1,164 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pci/mediatek-pcie-mt7623.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: PCIe controller on MediaTek SoCs
+
+maintainers:
+  - Christian Marangi <ansuelsmth@gmail.com>
+
+properties:
+  compatible:
+    enum:
+      - mediatek,mt2701-pcie
+      - mediatek,mt7623-pcie
+
+  reg:
+    minItems: 4
+    maxItems: 4
+
+  reg-names:
+    items:
+      - const: subsys
+      - const: port0
+      - const: port1
+      - const: port2
+
+  clocks:
+    minItems: 4
+    maxItems: 4
+
+  clock-names:
+    items:
+      - const: free_ck
+      - const: sys_ck0
+      - const: sys_ck1
+      - const: sys_ck2
+
+  resets:
+    minItems: 3
+    maxItems: 3
+
+  reset-names:
+    items:
+      - const: pcie-rst0
+      - const: pcie-rst1
+      - const: pcie-rst2
+
+  phys:
+    minItems: 3
+    maxItems: 3
+
+  phy-names:
+    items:
+      - const: pcie-phy0
+      - const: pcie-phy1
+      - const: pcie-phy2
+
+  power-domains:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - reg-names
+  - ranges
+  - clocks
+  - clock-names
+  - '#interrupt-cells'
+  - resets
+  - reset-names
+  - phys
+  - phy-names
+  - power-domains
+  - pcie@0,0
+  - pcie@1,0
+  - pcie@2,0
+
+allOf:
+  - $ref: /schemas/pci/pci-host-bridge.yaml#
+
+unevaluatedProperties: false
+
+examples:
+  # MT7623
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/clock/mt2701-clk.h>
+    #include <dt-bindings/reset/mt2701-resets.h>
+    #include <dt-bindings/phy/phy.h>
+    #include <dt-bindings/power/mt2701-power.h>
+
+    soc {
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        pcie@1a140000 {
+            compatible = "mediatek,mt7623-pcie";
+            device_type = "pci";
+            reg = <0 0x1a140000 0 0x1000>, /* PCIe shared registers */
+                  <0 0x1a142000 0 0x1000>, /* Port0 registers */
+                  <0 0x1a143000 0 0x1000>, /* Port1 registers */
+                  <0 0x1a144000 0 0x1000>; /* Port2 registers */
+            reg-names = "subsys", "port0", "port1", "port2";
+            #address-cells = <3>;
+            #size-cells = <2>;
+            #interrupt-cells = <1>;
+            interrupt-map-mask = <0xf800 0 0 0>;
+            interrupt-map = <0x0000 0 0 0 &sysirq GIC_SPI 193 IRQ_TYPE_LEVEL_LOW>,
+                            <0x0800 0 0 0 &sysirq GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>,
+                            <0x1000 0 0 0 &sysirq GIC_SPI 195 IRQ_TYPE_LEVEL_LOW>;
+            clocks = <&topckgen CLK_TOP_ETHIF_SEL>,
+                    <&hifsys CLK_HIFSYS_PCIE0>,
+                    <&hifsys CLK_HIFSYS_PCIE1>,
+                    <&hifsys CLK_HIFSYS_PCIE2>;
+            clock-names = "free_ck", "sys_ck0", "sys_ck1", "sys_ck2";
+            resets = <&hifsys MT2701_HIFSYS_PCIE0_RST>,
+                     <&hifsys MT2701_HIFSYS_PCIE1_RST>,
+                     <&hifsys MT2701_HIFSYS_PCIE2_RST>;
+            reset-names = "pcie-rst0", "pcie-rst1", "pcie-rst2";
+            phys = <&pcie0_phy PHY_TYPE_PCIE>, <&pcie1_phy PHY_TYPE_PCIE>,
+                   <&pcie2_phy PHY_TYPE_PCIE>;
+            phy-names = "pcie-phy0", "pcie-phy1", "pcie-phy2";
+            power-domains = <&scpsys MT2701_POWER_DOMAIN_HIF>;
+            bus-range = <0x00 0xff>;
+            ranges = <0x81000000 0 0x1a160000 0 0x1a160000 0 0x00010000>,	/* I/O space */
+                     <0x83000000 0 0x60000000 0 0x60000000 0 0x10000000>;	/* memory space */
+
+            pcie@0,0 {
+                device_type = "pci";
+                reg = <0x0000 0 0 0 0>;
+                #address-cells = <3>;
+                #size-cells = <2>;
+                #interrupt-cells = <1>;
+                interrupt-map-mask = <0 0 0 0>;
+                interrupt-map = <0 0 0 0 &sysirq GIC_SPI 193 IRQ_TYPE_LEVEL_LOW>;
+                ranges;
+            };
+
+            pcie@1,0 {
+                device_type = "pci";
+                reg = <0x0800 0 0 0 0>;
+                #address-cells = <3>;
+                #size-cells = <2>;
+                #interrupt-cells = <1>;
+                interrupt-map-mask = <0 0 0 0>;
+                interrupt-map = <0 0 0 0 &sysirq GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>;
+                ranges;
+            };
+
+            pcie@2,0 {
+                device_type = "pci";
+                reg = <0x1000 0 0 0 0>;
+                #address-cells = <3>;
+                #size-cells = <2>;
+                #interrupt-cells = <1>;
+                interrupt-map-mask = <0 0 0 0>;
+                interrupt-map = <0 0 0 0 &sysirq GIC_SPI 195 IRQ_TYPE_LEVEL_LOW>;
+                ranges;
+            };
+        };
+    };
diff --git a/Documentation/devicetree/bindings/pci/mediatek-pcie.txt b/Documentation/devicetree/bindings/pci/mediatek-pcie.txt
deleted file mode 100644
index 684227522267..000000000000
--- a/Documentation/devicetree/bindings/pci/mediatek-pcie.txt
+++ /dev/null
@@ -1,289 +0,0 @@
-MediaTek Gen2 PCIe controller
-
-Required properties:
-- compatible: Should contain one of the following strings:
-	"mediatek,mt2701-pcie"
-	"mediatek,mt2712-pcie"
-	"mediatek,mt7622-pcie"
-	"mediatek,mt7623-pcie"
-	"mediatek,mt7629-pcie"
-	"airoha,en7523-pcie"
-- device_type: Must be "pci"
-- reg: Base addresses and lengths of the root ports.
-- reg-names: Names of the above areas to use during resource lookup.
-- #address-cells: Address representation for root ports (must be 3)
-- #size-cells: Size representation for root ports (must be 2)
-- clocks: Must contain an entry for each entry in clock-names.
-  See ../clocks/clock-bindings.txt for details.
-- clock-names:
-  Mandatory entries:
-   - sys_ckN :transaction layer and data link layer clock
-  Required entries for MT2701/MT7623:
-   - free_ck :for reference clock of PCIe subsys
-  Required entries for MT2712/MT7622:
-   - ahb_ckN :AHB slave interface operating clock for CSR access and RC
-	      initiated MMIO access
-  Required entries for MT7622:
-   - axi_ckN :application layer MMIO channel operating clock
-   - aux_ckN :pe2_mac_bridge and pe2_mac_core operating clock when
-	      pcie_mac_ck/pcie_pipe_ck is turned off
-   - obff_ckN :OBFF functional block operating clock
-   - pipe_ckN :LTSSM and PHY/MAC layer operating clock
-  where N starting from 0 to one less than the number of root ports.
-- phys: List of PHY specifiers (used by generic PHY framework).
-- phy-names : Must be "pcie-phy0", "pcie-phy1", "pcie-phyN".. based on the
-  number of PHYs as specified in *phys* property.
-- power-domains: A phandle and power domain specifier pair to the power domain
-  which is responsible for collapsing and restoring power to the peripheral.
-- bus-range: Range of bus numbers associated with this controller.
-- ranges: Ranges for the PCI memory and I/O regions.
-
-Required properties for MT7623/MT2701:
-- #interrupt-cells: Size representation for interrupts (must be 1)
-- interrupt-map-mask and interrupt-map: Standard PCI IRQ mapping properties
-  Please refer to the standard PCI bus binding document for a more detailed
-  explanation.
-- resets: Must contain an entry for each entry in reset-names.
-  See ../reset/reset.txt for details.
-- reset-names: Must be "pcie-rst0", "pcie-rst1", "pcie-rstN".. based on the
-  number of root ports.
-
-Required properties for MT2712/MT7622/MT7629:
--interrupts: A list of interrupt outputs of the controller, must have one
-	     entry for each PCIe port
-- interrupt-names: Must include the following entries:
-	- "pcie_irq": The interrupt that is asserted when an MSI/INTX is received
-- linux,pci-domain: PCI domain ID. Should be unique for each host controller
-
-In addition, the device tree node must have sub-nodes describing each
-PCIe port interface, having the following mandatory properties:
-
-Required properties:
-- device_type: Must be "pci"
-- reg: Only the first four bytes are used to refer to the correct bus number
-  and device number.
-- #address-cells: Must be 3
-- #size-cells: Must be 2
-- #interrupt-cells: Must be 1
-- interrupt-map-mask and interrupt-map: Standard PCI IRQ mapping properties
-  Please refer to the standard PCI bus binding document for a more detailed
-  explanation.
-- ranges: Sub-ranges distributed from the PCIe controller node. An empty
-  property is sufficient.
-
-Examples for MT7623:
-
-	hifsys: syscon@1a000000 {
-		compatible = "mediatek,mt7623-hifsys",
-			     "mediatek,mt2701-hifsys",
-			     "syscon";
-		reg = <0 0x1a000000 0 0x1000>;
-		#clock-cells = <1>;
-		#reset-cells = <1>;
-	};
-
-	pcie: pcie@1a140000 {
-		compatible = "mediatek,mt7623-pcie";
-		device_type = "pci";
-		reg = <0 0x1a140000 0 0x1000>, /* PCIe shared registers */
-		      <0 0x1a142000 0 0x1000>, /* Port0 registers */
-		      <0 0x1a143000 0 0x1000>, /* Port1 registers */
-		      <0 0x1a144000 0 0x1000>; /* Port2 registers */
-		reg-names = "subsys", "port0", "port1", "port2";
-		#address-cells = <3>;
-		#size-cells = <2>;
-		#interrupt-cells = <1>;
-		interrupt-map-mask = <0xf800 0 0 0>;
-		interrupt-map = <0x0000 0 0 0 &sysirq GIC_SPI 193 IRQ_TYPE_LEVEL_LOW>,
-				<0x0800 0 0 0 &sysirq GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>,
-				<0x1000 0 0 0 &sysirq GIC_SPI 195 IRQ_TYPE_LEVEL_LOW>;
-		clocks = <&topckgen CLK_TOP_ETHIF_SEL>,
-			 <&hifsys CLK_HIFSYS_PCIE0>,
-			 <&hifsys CLK_HIFSYS_PCIE1>,
-			 <&hifsys CLK_HIFSYS_PCIE2>;
-		clock-names = "free_ck", "sys_ck0", "sys_ck1", "sys_ck2";
-		resets = <&hifsys MT2701_HIFSYS_PCIE0_RST>,
-			 <&hifsys MT2701_HIFSYS_PCIE1_RST>,
-			 <&hifsys MT2701_HIFSYS_PCIE2_RST>;
-		reset-names = "pcie-rst0", "pcie-rst1", "pcie-rst2";
-		phys = <&pcie0_phy PHY_TYPE_PCIE>, <&pcie1_phy PHY_TYPE_PCIE>,
-		       <&pcie2_phy PHY_TYPE_PCIE>;
-		phy-names = "pcie-phy0", "pcie-phy1", "pcie-phy2";
-		power-domains = <&scpsys MT2701_POWER_DOMAIN_HIF>;
-		bus-range = <0x00 0xff>;
-		ranges = <0x81000000 0 0x1a160000 0 0x1a160000 0 0x00010000	/* I/O space */
-			  0x83000000 0 0x60000000 0 0x60000000 0 0x10000000>;	/* memory space */
-
-		pcie@0,0 {
-			reg = <0x0000 0 0 0 0>;
-			#address-cells = <3>;
-			#size-cells = <2>;
-			#interrupt-cells = <1>;
-			interrupt-map-mask = <0 0 0 0>;
-			interrupt-map = <0 0 0 0 &sysirq GIC_SPI 193 IRQ_TYPE_LEVEL_LOW>;
-			ranges;
-		};
-
-		pcie@1,0 {
-			reg = <0x0800 0 0 0 0>;
-			#address-cells = <3>;
-			#size-cells = <2>;
-			#interrupt-cells = <1>;
-			interrupt-map-mask = <0 0 0 0>;
-			interrupt-map = <0 0 0 0 &sysirq GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>;
-			ranges;
-		};
-
-		pcie@2,0 {
-			reg = <0x1000 0 0 0 0>;
-			#address-cells = <3>;
-			#size-cells = <2>;
-			#interrupt-cells = <1>;
-			interrupt-map-mask = <0 0 0 0>;
-			interrupt-map = <0 0 0 0 &sysirq GIC_SPI 195 IRQ_TYPE_LEVEL_LOW>;
-			ranges;
-		};
-	};
-
-Examples for MT2712:
-
-	pcie1: pcie@112ff000 {
-		compatible = "mediatek,mt2712-pcie";
-		device_type = "pci";
-		reg = <0 0x112ff000 0 0x1000>;
-		reg-names = "port1";
-		linux,pci-domain = <1>;
-		#address-cells = <3>;
-		#size-cells = <2>;
-		interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "pcie_irq";
-		clocks = <&topckgen CLK_TOP_PE2_MAC_P1_SEL>,
-			 <&pericfg CLK_PERI_PCIE1>;
-		clock-names = "sys_ck1", "ahb_ck1";
-		phys = <&u3port1 PHY_TYPE_PCIE>;
-		phy-names = "pcie-phy1";
-		bus-range = <0x00 0xff>;
-		ranges = <0x82000000 0 0x11400000  0x0 0x11400000  0 0x300000>;
-		status = "disabled";
-
-		#interrupt-cells = <1>;
-		interrupt-map-mask = <0 0 0 7>;
-		interrupt-map = <0 0 0 1 &pcie_intc1 0>,
-				<0 0 0 2 &pcie_intc1 1>,
-				<0 0 0 3 &pcie_intc1 2>,
-				<0 0 0 4 &pcie_intc1 3>;
-		pcie_intc1: interrupt-controller {
-			interrupt-controller;
-			#address-cells = <0>;
-			#interrupt-cells = <1>;
-		};
-	};
-
-	pcie0: pcie@11700000 {
-		compatible = "mediatek,mt2712-pcie";
-		device_type = "pci";
-		reg = <0 0x11700000 0 0x1000>;
-		reg-names = "port0";
-		linux,pci-domain = <0>;
-		#address-cells = <3>;
-		#size-cells = <2>;
-		interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "pcie_irq";
-		clocks = <&topckgen CLK_TOP_PE2_MAC_P0_SEL>,
-			 <&pericfg CLK_PERI_PCIE0>;
-		clock-names = "sys_ck0", "ahb_ck0";
-		phys = <&u3port0 PHY_TYPE_PCIE>;
-		phy-names = "pcie-phy0";
-		bus-range = <0x00 0xff>;
-		ranges = <0x82000000 0 0x20000000 0x0 0x20000000 0 0x10000000>;
-		status = "disabled";
-
-		#interrupt-cells = <1>;
-		interrupt-map-mask = <0 0 0 7>;
-		interrupt-map = <0 0 0 1 &pcie_intc0 0>,
-				<0 0 0 2 &pcie_intc0 1>,
-				<0 0 0 3 &pcie_intc0 2>,
-				<0 0 0 4 &pcie_intc0 3>;
-		pcie_intc0: interrupt-controller {
-			interrupt-controller;
-			#address-cells = <0>;
-			#interrupt-cells = <1>;
-		};
-	};
-
-Examples for MT7622:
-
-	pcie0: pcie@1a143000 {
-		compatible = "mediatek,mt7622-pcie";
-		device_type = "pci";
-		reg = <0 0x1a143000 0 0x1000>;
-		reg-names = "port0";
-		linux,pci-domain = <0>;
-		#address-cells = <3>;
-		#size-cells = <2>;
-		interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_LOW>;
-		interrupt-names = "pcie_irq";
-		clocks = <&pciesys CLK_PCIE_P0_MAC_EN>,
-			 <&pciesys CLK_PCIE_P0_AHB_EN>,
-			 <&pciesys CLK_PCIE_P0_AUX_EN>,
-			 <&pciesys CLK_PCIE_P0_AXI_EN>,
-			 <&pciesys CLK_PCIE_P0_OBFF_EN>,
-			 <&pciesys CLK_PCIE_P0_PIPE_EN>;
-		clock-names = "sys_ck0", "ahb_ck0", "aux_ck0",
-			      "axi_ck0", "obff_ck0", "pipe_ck0";
-
-		power-domains = <&scpsys MT7622_POWER_DOMAIN_HIF0>;
-		bus-range = <0x00 0xff>;
-		ranges = <0x82000000 0 0x20000000  0x0 0x20000000  0 0x8000000>;
-		status = "disabled";
-
-		#interrupt-cells = <1>;
-		interrupt-map-mask = <0 0 0 7>;
-		interrupt-map = <0 0 0 1 &pcie_intc0 0>,
-				<0 0 0 2 &pcie_intc0 1>,
-				<0 0 0 3 &pcie_intc0 2>,
-				<0 0 0 4 &pcie_intc0 3>;
-		pcie_intc0: interrupt-controller {
-			interrupt-controller;
-			#address-cells = <0>;
-			#interrupt-cells = <1>;
-		};
-	};
-
-	pcie1: pcie@1a145000 {
-		compatible = "mediatek,mt7622-pcie";
-		device_type = "pci";
-		reg = <0 0x1a145000 0 0x1000>;
-		reg-names = "port1";
-		linux,pci-domain = <1>;
-		#address-cells = <3>;
-		#size-cells = <2>;
-		interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_LOW>;
-		interrupt-names = "pcie_irq";
-		clocks = <&pciesys CLK_PCIE_P1_MAC_EN>,
-			 /* designer has connect RC1 with p0_ahb clock */
-			 <&pciesys CLK_PCIE_P0_AHB_EN>,
-			 <&pciesys CLK_PCIE_P1_AUX_EN>,
-			 <&pciesys CLK_PCIE_P1_AXI_EN>,
-			 <&pciesys CLK_PCIE_P1_OBFF_EN>,
-			 <&pciesys CLK_PCIE_P1_PIPE_EN>;
-		clock-names = "sys_ck1", "ahb_ck1", "aux_ck1",
-			      "axi_ck1", "obff_ck1", "pipe_ck1";
-
-		power-domains = <&scpsys MT7622_POWER_DOMAIN_HIF0>;
-		bus-range = <0x00 0xff>;
-		ranges = <0x82000000 0 0x28000000  0x0 0x28000000  0 0x8000000>;
-		status = "disabled";
-
-		#interrupt-cells = <1>;
-		interrupt-map-mask = <0 0 0 7>;
-		interrupt-map = <0 0 0 1 &pcie_intc1 0>,
-				<0 0 0 2 &pcie_intc1 1>,
-				<0 0 0 3 &pcie_intc1 2>,
-				<0 0 0 4 &pcie_intc1 3>;
-		pcie_intc1: interrupt-controller {
-			interrupt-controller;
-			#address-cells = <0>;
-			#interrupt-cells = <1>;
-		};
-	};
diff --git a/Documentation/devicetree/bindings/pci/mediatek-pcie.yaml b/Documentation/devicetree/bindings/pci/mediatek-pcie.yaml
new file mode 100644
index 000000000000..fca6cb20d18b
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/mediatek-pcie.yaml
@@ -0,0 +1,318 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pci/mediatek-pcie.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: PCIe controller on MediaTek SoCs
+
+maintainers:
+  - Christian Marangi <ansuelsmth@gmail.com>
+
+properties:
+  compatible:
+    oneOf:
+      - enum:
+          - mediatek,mt2712-pcie
+          - mediatek,mt7622-pcie
+          - mediatek,mt7629-pcie
+      - items:
+          - const: airoha,en7523-pcie
+          - const: mediatek,mt7622-pcie
+
+  reg:
+    maxItems: 1
+
+  reg-names:
+    enum: [ port0, port1 ]
+
+  clocks:
+    minItems: 1
+    maxItems: 6
+
+  clock-names:
+    minItems: 1
+    items:
+      - enum: [ sys_ck0, sys_ck1 ]
+      - enum: [ ahb_ck0, ahb_ck1 ]
+      - enum: [ aux_ck0, aux_ck1 ]
+      - enum: [ axi_ck0, axi_ck1 ]
+      - enum: [ obff_ck0, obff_ck1 ]
+      - enum: [ pipe_ck0, pipe_ck1 ]
+
+  interrupts:
+    maxItems: 1
+
+  interrupt-names:
+    const: pcie_irq
+
+  phys:
+    maxItems: 1
+
+  phy-names:
+    enum: [ pcie-phy0, pcie-phy1 ]
+
+  power-domains:
+    maxItems: 1
+
+  '#interrupt-cells':
+    const: 1
+
+  interrupt-controller:
+    description: Interrupt controller node for handling legacy PCI interrupts.
+    type: object
+    properties:
+      '#address-cells':
+        const: 0
+      '#interrupt-cells':
+        const: 1
+      interrupt-controller: true
+
+    required:
+      - '#address-cells'
+      - '#interrupt-cells'
+      - interrupt-controller
+
+    additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - reg-names
+  - ranges
+  - clocks
+  - clock-names
+  - '#interrupt-cells'
+  - interrupts
+  - interrupt-names
+  - interrupt-controller
+
+allOf:
+  - $ref: /schemas/pci/pci-host-bridge.yaml#
+
+  - if:
+      properties:
+        compatible:
+          const: mediatek,mt2712-pcie
+    then:
+      properties:
+        clocks:
+          minItems: 2
+          maxItems: 2
+
+        clock-names:
+          minItems: 2
+          maxItems: 2
+
+        power-domains: false
+
+      required:
+        - phys
+        - phy-names
+
+  - if:
+      properties:
+        compatible:
+          const: mediatek,mt7622-pcie
+    then:
+      properties:
+        clocks:
+          minItems: 6
+
+        phys: false
+
+        phy-names: false
+
+      required:
+        - power-domains
+
+  - if:
+      properties:
+        compatible:
+          const: mediatek,mt7629-pcie
+    then:
+      properties:
+        clocks:
+          minItems: 6
+
+      required:
+        - power-domains
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: airoha,en7523-pcie
+    then:
+      properties:
+        clocks:
+          maxItems: 1
+
+        clock-names:
+          maxItems: 1
+
+        phys: false
+
+        phy-names: false
+
+        power-domain: false
+
+unevaluatedProperties: false
+
+examples:
+  # MT2712
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/phy/phy.h>
+
+    soc_1 {
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        pcie@112ff000 {
+            compatible = "mediatek,mt2712-pcie";
+            device_type = "pci";
+            reg = <0 0x112ff000 0 0x1000>;
+            reg-names = "port1";
+            linux,pci-domain = <1>;
+            #address-cells = <3>;
+            #size-cells = <2>;
+            interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+            interrupt-names = "pcie_irq";
+            clocks = <&topckgen>, /* CLK_TOP_PE2_MAC_P1_SEL */
+                     <&pericfg>; /* CLK_PERI_PCIE1 */
+            clock-names = "sys_ck1", "ahb_ck1";
+            phys = <&u3port1 PHY_TYPE_PCIE>;
+            phy-names = "pcie-phy1";
+            bus-range = <0x00 0xff>;
+            ranges = <0x82000000 0 0x11400000  0x0 0x11400000  0 0x300000>;
+
+            #interrupt-cells = <1>;
+            interrupt-map-mask = <0 0 0 7>;
+            interrupt-map = <0 0 0 1 &pcie_intc1 0>,
+                            <0 0 0 2 &pcie_intc1 1>,
+                            <0 0 0 3 &pcie_intc1 2>,
+                            <0 0 0 4 &pcie_intc1 3>;
+            pcie_intc1: interrupt-controller {
+                interrupt-controller;
+                #address-cells = <0>;
+                #interrupt-cells = <1>;
+            };
+        };
+
+        pcie@11700000 {
+            compatible = "mediatek,mt2712-pcie";
+            device_type = "pci";
+            reg = <0 0x11700000 0 0x1000>;
+            reg-names = "port0";
+            linux,pci-domain = <0>;
+            #address-cells = <3>;
+            #size-cells = <2>;
+            interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
+            interrupt-names = "pcie_irq";
+            clocks = <&topckgen>, /* CLK_TOP_PE2_MAC_P0_SEL */
+                     <&pericfg>; /* CLK_PERI_PCIE0 */
+            clock-names = "sys_ck0", "ahb_ck0";
+            phys = <&u3port0 PHY_TYPE_PCIE>;
+            phy-names = "pcie-phy0";
+            bus-range = <0x00 0xff>;
+            ranges = <0x82000000 0 0x20000000 0x0 0x20000000 0 0x10000000>;
+
+            #interrupt-cells = <1>;
+            interrupt-map-mask = <0 0 0 7>;
+            interrupt-map = <0 0 0 1 &pcie_intc0 0>,
+                            <0 0 0 2 &pcie_intc0 1>,
+                            <0 0 0 3 &pcie_intc0 2>,
+                            <0 0 0 4 &pcie_intc0 3>;
+            pcie_intc0: interrupt-controller {
+                interrupt-controller;
+                #address-cells = <0>;
+                #interrupt-cells = <1>;
+            };
+        };
+    };
+
+  # MT7622
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/power/mt7622-power.h>
+
+    soc_2 {
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        pcie@1a143000 {
+            compatible = "mediatek,mt7622-pcie";
+            device_type = "pci";
+            reg = <0 0x1a143000 0 0x1000>;
+            reg-names = "port0";
+            linux,pci-domain = <0>;
+            #address-cells = <3>;
+            #size-cells = <2>;
+            interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_LOW>;
+            interrupt-names = "pcie_irq";
+            clocks = <&pciesys>, /* CLK_PCIE_P0_MAC_EN */
+                     <&pciesys>, /* CLK_PCIE_P0_AHB_EN */
+                     <&pciesys>, /* CLK_PCIE_P0_AUX_EN */
+                     <&pciesys>, /* CLK_PCIE_P0_AXI_EN */
+                     <&pciesys>, /* CLK_PCIE_P0_OBFF_EN */
+                     <&pciesys>; /* CLK_PCIE_P0_PIPE_EN */
+            clock-names = "sys_ck0", "ahb_ck0", "aux_ck0",
+                          "axi_ck0", "obff_ck0", "pipe_ck0";
+
+            power-domains = <&scpsys MT7622_POWER_DOMAIN_HIF0>;
+            bus-range = <0x00 0xff>;
+            ranges = <0x82000000 0 0x20000000  0x0 0x20000000  0 0x8000000>;
+
+            #interrupt-cells = <1>;
+            interrupt-map-mask = <0 0 0 7>;
+            interrupt-map = <0 0 0 1 &pcie_intc0_1 0>,
+                            <0 0 0 2 &pcie_intc0_1 1>,
+                            <0 0 0 3 &pcie_intc0_1 2>,
+                            <0 0 0 4 &pcie_intc0_1 3>;
+            pcie_intc0_1: interrupt-controller {
+                interrupt-controller;
+                #address-cells = <0>;
+                #interrupt-cells = <1>;
+            };
+        };
+
+        pcie@1a145000 {
+            compatible = "mediatek,mt7622-pcie";
+            device_type = "pci";
+            reg = <0 0x1a145000 0 0x1000>;
+            reg-names = "port1";
+            linux,pci-domain = <1>;
+            #address-cells = <3>;
+            #size-cells = <2>;
+            interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_LOW>;
+            interrupt-names = "pcie_irq";
+            clocks = <&pciesys>, /* CLK_PCIE_P1_MAC_EN */
+                     /* designer has connect RC1 with p0_ahb clock */
+                     <&pciesys>, /* CLK_PCIE_P0_AHB_EN */
+                     <&pciesys>, /* CLK_PCIE_P1_AUX_EN */
+                     <&pciesys>, /* CLK_PCIE_P1_AXI_EN */
+                     <&pciesys>, /* CLK_PCIE_P1_OBFF_EN */
+                     <&pciesys>; /* CLK_PCIE_P1_PIPE_EN */
+            clock-names = "sys_ck1", "ahb_ck1", "aux_ck1",
+                          "axi_ck1", "obff_ck1", "pipe_ck1";
+
+            power-domains = <&scpsys MT7622_POWER_DOMAIN_HIF0>;
+            bus-range = <0x00 0xff>;
+            ranges = <0x82000000 0 0x28000000  0x0 0x28000000  0 0x8000000>;
+
+            #interrupt-cells = <1>;
+            interrupt-map-mask = <0 0 0 7>;
+            interrupt-map = <0 0 0 1 &pcie_intc1_1 0>,
+                            <0 0 0 2 &pcie_intc1_1 1>,
+                            <0 0 0 3 &pcie_intc1_1 2>,
+                            <0 0 0 4 &pcie_intc1_1 3>;
+            pcie_intc1_1: interrupt-controller {
+                interrupt-controller;
+                #address-cells = <0>;
+                #interrupt-cells = <1>;
+            };
+        };
+    };
-- 
2.51.0

[PATCH v4 3/5] dt-bindings: PCI: mediatek: Add support for Airoha AN7583

[Christian Marangi]

Introduce Airoha AN7583 SoC compatible in mediatek PCIe controller
binding.

Similar to GEN3, the Airoha AN7583 GEN2 PCIe controller require the
PBUS csr property to permit the correct functionality of the PCIe
controller.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
---
 .../bindings/pci/mediatek-pcie.yaml           | 110 ++++++++++++++++++
 1 file changed, 110 insertions(+)

diff --git a/Documentation/devicetree/bindings/pci/mediatek-pcie.yaml b/Documentation/devicetree/bindings/pci/mediatek-pcie.yaml
index fca6cb20d18b..b91b13a0220c 100644
--- a/Documentation/devicetree/bindings/pci/mediatek-pcie.yaml
+++ b/Documentation/devicetree/bindings/pci/mediatek-pcie.yaml
@@ -13,6 +13,7 @@ properties:
   compatible:
     oneOf:
       - enum:
+          - airoha,an7583-pcie
           - mediatek,mt2712-pcie
           - mediatek,mt7622-pcie
           - mediatek,mt7629-pcie
@@ -55,6 +56,17 @@ properties:
   power-domains:
     maxItems: 1
 
+  mediatek,pbus-csr:
+    $ref: /schemas/types.yaml#/definitions/phandle-array
+    items:
+      - items:
+          - description: phandle to pbus-csr syscon
+          - description: offset of pbus-csr base address register
+          - description: offset of pbus-csr base address mask register
+    description:
+      Phandle with two arguments to the syscon node used to detect if
+      a given address is accessible on PCIe controller.
+
   '#interrupt-cells':
     const: 1
 
@@ -90,6 +102,45 @@ required:
 allOf:
   - $ref: /schemas/pci/pci-host-bridge.yaml#
 
+  - if:
+      properties:
+        compatible:
+          const: airoha,an7583-pcie
+    then:
+      properties:
+        reg:
+          maxItems: 1
+
+        reg-names:
+          const: port1
+
+        clocks:
+          maxItems: 1
+
+        clock-names:
+          const: sys_ck1
+
+        reset:
+          maxItems: 1
+
+        reset-names:
+          const: pcie-rst1
+
+        phys:
+          maxItems: 1
+
+        phy-names:
+          const: pcie-phy1
+
+        power-domain: false
+
+      required:
+        - resets
+        - reset-names
+        - phys
+        - phy-names
+        - mediatek,pbus-csr
+
   - if:
       properties:
         compatible:
@@ -106,6 +157,8 @@ allOf:
 
         power-domains: false
 
+        mediatek,pbus-csr: false
+
       required:
         - phys
         - phy-names
@@ -123,6 +176,8 @@ allOf:
 
         phy-names: false
 
+        mediatek,pbus-csr: false
+
       required:
         - power-domains
 
@@ -135,6 +190,8 @@ allOf:
         clocks:
           minItems: 6
 
+        mediatek,pbus-csr: false
+
       required:
         - power-domains
 
@@ -157,6 +214,8 @@ allOf:
 
         power-domain: false
 
+        mediatek,pbus-csr: false
+
 unevaluatedProperties: false
 
 examples:
@@ -316,3 +375,54 @@ examples:
             };
         };
     };
+
+  # AN7583
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/clock/en7523-clk.h>
+
+    soc_3 {
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        pcie@1fa92000 {
+            compatible = "airoha,an7583-pcie";
+            device_type = "pci";
+            linux,pci-domain = <1>;
+            #address-cells = <3>;
+            #size-cells = <2>;
+
+            reg = <0x0 0x1fa92000 0x0 0x1670>;
+            reg-names = "port1";
+
+            clocks = <&scuclk EN7523_CLK_PCIE>;
+            clock-names = "sys_ck1";
+
+            phys = <&pciephy>;
+            phy-names = "pcie-phy1";
+
+            ranges = <0x02000000 0 0x24000000 0x0 0x24000000 0 0x4000000>;
+
+            resets = <&scuclk>; /* AN7583_PCIE1_RST */
+            reset-names = "pcie-rst1";
+
+            mediatek,pbus-csr = <&pbus_csr 0x8 0xc>;
+
+            interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+            interrupt-names = "pcie_irq";
+            bus-range = <0x00 0xff>;
+            #interrupt-cells = <1>;
+            interrupt-map-mask = <0 0 0 7>;
+            interrupt-map = <0 0 0 1 &pcie_intc1 0>,
+                            <0 0 0 2 &pcie_intc1 1>,
+                            <0 0 0 3 &pcie_intc1 2>,
+                            <0 0 0 4 &pcie_intc1 3>;
+
+            pcie_intc1_4: interrupt-controller {
+                interrupt-controller;
+                #address-cells = <0>;
+                #interrupt-cells = <1>;
+            };
+        };
+    };
-- 
2.51.0

[PATCH v4 4/5] PCI: mediatek: convert bool to single flags entry and bitmap

[Christian Marangi]

To clean Mediatek SoC PCIe struct, convert all the bool to a bitmap and
use a single flags to reference all the values. This permits cleaner
addition of new flag without having to define a new bool in the struct.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
---
 drivers/pci/controller/pcie-mediatek.c | 28 +++++++++++++++-----------
 1 file changed, 16 insertions(+), 12 deletions(-)

diff --git a/drivers/pci/controller/pcie-mediatek.c b/drivers/pci/controller/pcie-mediatek.c
index 24cc30a2ab6c..1678461e56d3 100644
--- a/drivers/pci/controller/pcie-mediatek.c
+++ b/drivers/pci/controller/pcie-mediatek.c
@@ -142,24 +142,29 @@
 
 struct mtk_pcie_port;
 
+enum mtk_pcie_flags {
+	NEED_FIX_CLASS_ID = BIT(0), /* host's class ID needed to be fixed */
+	NEED_FIX_DEVICE_ID = BIT(1), /* host's device ID needed to be fixed */
+	NO_MSI = BIT(2), /* Bridge has no MSI support, and relies on an
+			  * external block
+			  */
+};
+
 /**
  * struct mtk_pcie_soc - differentiate between host generations
- * @need_fix_class_id: whether this host's class ID needed to be fixed or not
- * @need_fix_device_id: whether this host's device ID needed to be fixed or not
  * @no_msi: Bridge has no MSI support, and relies on an external block
  * @device_id: device ID which this host need to be fixed
  * @ops: pointer to configuration access functions
  * @startup: pointer to controller setting functions
  * @setup_irq: pointer to initialize IRQ functions
+ * @flags: pcie device flags.
  */
 struct mtk_pcie_soc {
-	bool need_fix_class_id;
-	bool need_fix_device_id;
-	bool no_msi;
 	unsigned int device_id;
 	struct pci_ops *ops;
 	int (*startup)(struct mtk_pcie_port *port);
 	int (*setup_irq)(struct mtk_pcie_port *port, struct device_node *node);
+	u32 flags;
 };
 
 /**
@@ -703,7 +708,7 @@ static int mtk_pcie_startup_port_v2(struct mtk_pcie_port *port)
 	writel(val, port->base + PCIE_RST_CTRL);
 
 	/* Set up vendor ID and class code */
-	if (soc->need_fix_class_id) {
+	if (soc->flags & NEED_FIX_CLASS_ID) {
 		val = PCI_VENDOR_ID_MEDIATEK;
 		writew(val, port->base + PCIE_CONF_VEND_ID);
 
@@ -711,7 +716,7 @@ static int mtk_pcie_startup_port_v2(struct mtk_pcie_port *port)
 		writew(val, port->base + PCIE_CONF_CLASS_ID);
 	}
 
-	if (soc->need_fix_device_id)
+	if (soc->flags & NEED_FIX_DEVICE_ID)
 		writew(soc->device_id, port->base + PCIE_CONF_DEVICE_ID);
 
 	/* 100ms timeout value should be enough for Gen1/2 training */
@@ -1099,7 +1104,7 @@ static int mtk_pcie_probe(struct platform_device *pdev)
 
 	host->ops = pcie->soc->ops;
 	host->sysdata = pcie;
-	host->msi_domain = pcie->soc->no_msi;
+	host->msi_domain = !!(pcie->soc->flags & NO_MSI);
 
 	err = pci_host_probe(host);
 	if (err)
@@ -1187,9 +1192,9 @@ static const struct dev_pm_ops mtk_pcie_pm_ops = {
 };
 
 static const struct mtk_pcie_soc mtk_pcie_soc_v1 = {
-	.no_msi = true,
 	.ops = &mtk_pcie_ops,
 	.startup = mtk_pcie_startup_port,
+	.flags = NO_MSI,
 };
 
 static const struct mtk_pcie_soc mtk_pcie_soc_mt2712 = {
@@ -1199,19 +1204,18 @@ static const struct mtk_pcie_soc mtk_pcie_soc_mt2712 = {
 };
 
 static const struct mtk_pcie_soc mtk_pcie_soc_mt7622 = {
-	.need_fix_class_id = true,
 	.ops = &mtk_pcie_ops_v2,
 	.startup = mtk_pcie_startup_port_v2,
 	.setup_irq = mtk_pcie_setup_irq,
+	.flags = NEED_FIX_CLASS_ID,
 };
 
 static const struct mtk_pcie_soc mtk_pcie_soc_mt7629 = {
-	.need_fix_class_id = true,
-	.need_fix_device_id = true,
 	.device_id = PCI_DEVICE_ID_MEDIATEK_7629,
 	.ops = &mtk_pcie_ops_v2,
 	.startup = mtk_pcie_startup_port_v2,
 	.setup_irq = mtk_pcie_setup_irq,
+	.flags = NEED_FIX_CLASS_ID | NEED_FIX_DEVICE_ID,
 };
 
 static const struct of_device_id mtk_pcie_ids[] = {
-- 
2.51.0

[PATCH v4 5/5] PCI: mediatek: add support for Airoha AN7583 SoC

[Christian Marangi]

Add support for the second PCIe Root Complex present on Airoha AN7583
SoC.

This is based on the Mediatek Gen1/2 PCIe driver and similar to Gen3
also require workaround for the reset signals.

Introduce a new flag to skip having to reset signals and also introduce
some additional logic to configure the PBUS registers required for
Airoha SoC.

While at it, also add additional info on the PERST# Signal delay
comments and use dedicated macro.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
---
 drivers/pci/controller/pcie-mediatek.c | 92 ++++++++++++++++++++------
 1 file changed, 70 insertions(+), 22 deletions(-)

diff --git a/drivers/pci/controller/pcie-mediatek.c b/drivers/pci/controller/pcie-mediatek.c
index 1678461e56d3..3340c005da4b 100644
--- a/drivers/pci/controller/pcie-mediatek.c
+++ b/drivers/pci/controller/pcie-mediatek.c
@@ -148,6 +148,7 @@ enum mtk_pcie_flags {
 	NO_MSI = BIT(2), /* Bridge has no MSI support, and relies on an
 			  * external block
 			  */
+	SKIP_PCIE_RSTB	= BIT(3), /* Skip calling RSTB bits on PCIe probe */
 };
 
 /**
@@ -684,28 +685,32 @@ static int mtk_pcie_startup_port_v2(struct mtk_pcie_port *port)
 		regmap_update_bits(pcie->cfg, PCIE_SYS_CFG_V2, val, val);
 	}
 
-	/* Assert all reset signals */
-	writel(0, port->base + PCIE_RST_CTRL);
-
-	/*
-	 * Enable PCIe link down reset, if link status changed from link up to
-	 * link down, this will reset MAC control registers and configuration
-	 * space.
-	 */
-	writel(PCIE_LINKDOWN_RST_EN, port->base + PCIE_RST_CTRL);
-
-	/*
-	 * Described in PCIe CEM specification sections 2.2 (PERST# Signal) and
-	 * 2.2.1 (Initial Power-Up (G3 to S0)). The deassertion of PERST# should
-	 * be delayed 100ms (TPVPERL) for the power and clock to become stable.
-	 */
-	msleep(100);
-
-	/* De-assert PHY, PE, PIPE, MAC and configuration reset	*/
-	val = readl(port->base + PCIE_RST_CTRL);
-	val |= PCIE_PHY_RSTB | PCIE_PERSTB | PCIE_PIPE_SRSTB |
-	       PCIE_MAC_SRSTB | PCIE_CRSTB;
-	writel(val, port->base + PCIE_RST_CTRL);
+	if (!(soc->flags & SKIP_PCIE_RSTB)) {
+		/* Assert all reset signals */
+		writel(0, port->base + PCIE_RST_CTRL);
+
+		/*
+		 * Enable PCIe link down reset, if link status changed from
+		 * link up to link down, this will reset MAC control registers
+		 * and configuration space.
+		 */
+		writel(PCIE_LINKDOWN_RST_EN, port->base + PCIE_RST_CTRL);
+
+		/*
+		 * Described in PCIe CEM specification revision 3.0 sections
+		 * 2.2 (PERST# Signal) and 2.2.1 (Initial Power-Up (G3 to S0)).
+		 *
+		 * The deassertion of PERST# should be delayed 100ms (TPVPERL)
+		 * for the power and clock to become stable.
+		 */
+		msleep(PCIE_T_PVPERL_MS);
+
+		/* De-assert PHY, PE, PIPE, MAC and configuration reset	*/
+		val = readl(port->base + PCIE_RST_CTRL);
+		val |= PCIE_PHY_RSTB | PCIE_PERSTB | PCIE_PIPE_SRSTB |
+		       PCIE_MAC_SRSTB | PCIE_CRSTB;
+		writel(val, port->base + PCIE_RST_CTRL);
+	}
 
 	/* Set up vendor ID and class code */
 	if (soc->flags & NEED_FIX_CLASS_ID) {
@@ -826,6 +831,41 @@ static int mtk_pcie_startup_port(struct mtk_pcie_port *port)
 	return 0;
 }
 
+static int mtk_pcie_startup_port_an7583(struct mtk_pcie_port *port)
+{
+	struct mtk_pcie *pcie = port->pcie;
+	struct device *dev = pcie->dev;
+	struct pci_host_bridge *host;
+	struct resource_entry *entry;
+	struct regmap *pbus_regmap;
+	resource_size_t addr;
+	u32 args[2], size;
+
+	/*
+	 * Configure PBus base address and base address mask to allow
+	 * the hw to detect if a given address is accessible on PCIe
+	 * controller.
+	 */
+	pbus_regmap = syscon_regmap_lookup_by_phandle_args(dev->of_node,
+							   "mediatek,pbus-csr",
+							   ARRAY_SIZE(args),
+							   args);
+	if (IS_ERR(pbus_regmap))
+		return PTR_ERR(pbus_regmap);
+
+	host = pci_host_bridge_from_priv(pcie);
+	entry = resource_list_first_type(&host->windows, IORESOURCE_MEM);
+	if (!entry)
+		return -ENODEV;
+
+	addr = entry->res->start - entry->offset;
+	regmap_write(pbus_regmap, args[0], lower_32_bits(addr));
+	size = lower_32_bits(resource_size(entry->res));
+	regmap_write(pbus_regmap, args[1], GENMASK(31, __fls(size)));
+
+	return mtk_pcie_startup_port_v2(port);
+}
+
 static void mtk_pcie_enable_port(struct mtk_pcie_port *port)
 {
 	struct mtk_pcie *pcie = port->pcie;
@@ -1210,6 +1250,13 @@ static const struct mtk_pcie_soc mtk_pcie_soc_mt7622 = {
 	.flags = NEED_FIX_CLASS_ID,
 };
 
+static const struct mtk_pcie_soc mtk_pcie_soc_an7583 = {
+	.ops = &mtk_pcie_ops_v2,
+	.startup = mtk_pcie_startup_port_an7583,
+	.setup_irq = mtk_pcie_setup_irq,
+	.flags = NEED_FIX_CLASS_ID | SKIP_PCIE_RSTB,
+};
+
 static const struct mtk_pcie_soc mtk_pcie_soc_mt7629 = {
 	.device_id = PCI_DEVICE_ID_MEDIATEK_7629,
 	.ops = &mtk_pcie_ops_v2,
@@ -1219,6 +1266,7 @@ static const struct mtk_pcie_soc mtk_pcie_soc_mt7629 = {
 };
 
 static const struct of_device_id mtk_pcie_ids[] = {
+	{ .compatible = "airoha,an7583-pcie", .data = &mtk_pcie_soc_an7583 },
 	{ .compatible = "mediatek,mt2701-pcie", .data = &mtk_pcie_soc_v1 },
 	{ .compatible = "mediatek,mt7623-pcie", .data = &mtk_pcie_soc_v1 },
 	{ .compatible = "mediatek,mt2712-pcie", .data = &mtk_pcie_soc_mt2712 },
-- 
2.51.0

Re: [PATCH v4 3/5] dt-bindings: PCI: mediatek: Add support for Airoha AN7583

[Rob Herring (Arm)]

On Mon, 29 Sep 2025 13:38:02 +0200, Christian Marangi wrote:
> Introduce Airoha AN7583 SoC compatible in mediatek PCIe controller
> binding.
> 
> Similar to GEN3, the Airoha AN7583 GEN2 PCIe controller require the
> PBUS csr property to permit the correct functionality of the PCIe
> controller.
> 
> Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
> ---
>  .../bindings/pci/mediatek-pcie.yaml           | 110 ++++++++++++++++++
>  1 file changed, 110 insertions(+)
> 

My bot found errors running 'make dt_binding_check' on your patch:

yamllint warnings/errors:

dtschema/dtc warnings/errors:
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/pci/mediatek-pcie.example.dtb: pcie@1fa92000 (airoha,an7583-pcie): Unevaluated properties are not allowed ('resets' was unexpected)
	from schema $id: http://devicetree.org/schemas/pci/mediatek-pcie.yaml#

doc reference errors (make refcheckdocs):

See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20250929113806.2484-4-ansuelsmth@gmail.com

The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.

Re: [PATCH v4 3/5] dt-bindings: PCI: mediatek: Add support for Airoha AN7583

[Rob Herring]

On Mon, Sep 29, 2025 at 01:38:02PM +0200, Christian Marangi wrote:
> Introduce Airoha AN7583 SoC compatible in mediatek PCIe controller
> binding.
> 
> Similar to GEN3, the Airoha AN7583 GEN2 PCIe controller require the
> PBUS csr property to permit the correct functionality of the PCIe
> controller.

I guess I didn't get my point across before. Test your crap before 
sending or I'm going to stop reviewing your stuff.

> 
> Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
> ---
>  .../bindings/pci/mediatek-pcie.yaml           | 110 ++++++++++++++++++
>  1 file changed, 110 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/pci/mediatek-pcie.yaml b/Documentation/devicetree/bindings/pci/mediatek-pcie.yaml
> index fca6cb20d18b..b91b13a0220c 100644
> --- a/Documentation/devicetree/bindings/pci/mediatek-pcie.yaml
> +++ b/Documentation/devicetree/bindings/pci/mediatek-pcie.yaml
> @@ -13,6 +13,7 @@ properties:
>    compatible:
>      oneOf:
>        - enum:
> +          - airoha,an7583-pcie
>            - mediatek,mt2712-pcie
>            - mediatek,mt7622-pcie
>            - mediatek,mt7629-pcie
> @@ -55,6 +56,17 @@ properties:
>    power-domains:
>      maxItems: 1
>  
> +  mediatek,pbus-csr:
> +    $ref: /schemas/types.yaml#/definitions/phandle-array
> +    items:
> +      - items:
> +          - description: phandle to pbus-csr syscon
> +          - description: offset of pbus-csr base address register
> +          - description: offset of pbus-csr base address mask register
> +    description:
> +      Phandle with two arguments to the syscon node used to detect if
> +      a given address is accessible on PCIe controller.
> +
>    '#interrupt-cells':
>      const: 1
>  
> @@ -90,6 +102,45 @@ required:
>  allOf:
>    - $ref: /schemas/pci/pci-host-bridge.yaml#
>  
> +  - if:
> +      properties:
> +        compatible:
> +          const: airoha,an7583-pcie
> +    then:
> +      properties:
> +        reg:
> +          maxItems: 1

That's already the maximum. Drop.

> +
> +        reg-names:
> +          const: port1
> +
> +        clocks:
> +          maxItems: 1
> +
> +        clock-names:
> +          const: sys_ck1
> +
> +        reset:
> +          maxItems: 1

That's already the maximum. Drop.

> +
> +        reset-names:
> +          const: pcie-rst1
> +
> +        phys:
> +          maxItems: 1

That's already the maximum. Drop.

> +
> +        phy-names:
> +          const: pcie-phy1
> +
> +        power-domain: false
> +
> +      required:
> +        - resets
> +        - reset-names
> +        - phys
> +        - phy-names
> +        - mediatek,pbus-csr
> +
>    - if:
>        properties:
>          compatible:
> @@ -106,6 +157,8 @@ allOf:
>  
>          power-domains: false
>  
> +        mediatek,pbus-csr: false
> +
>        required:
>          - phys
>          - phy-names
> @@ -123,6 +176,8 @@ allOf:
>  
>          phy-names: false
>  
> +        mediatek,pbus-csr: false
> +
>        required:
>          - power-domains
>  
> @@ -135,6 +190,8 @@ allOf:
>          clocks:
>            minItems: 6
>  
> +        mediatek,pbus-csr: false
> +
>        required:
>          - power-domains
>  
> @@ -157,6 +214,8 @@ allOf:
>  
>          power-domain: false
>  
> +        mediatek,pbus-csr: false
> +
>  unevaluatedProperties: false
>  
>  examples:
> @@ -316,3 +375,54 @@ examples:
>              };
>          };
>      };
> +
> +  # AN7583
> +  - |
> +    #include <dt-bindings/interrupt-controller/irq.h>
> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> +    #include <dt-bindings/clock/en7523-clk.h>
> +
> +    soc_3 {
> +        #address-cells = <2>;
> +        #size-cells = <2>;
> +
> +        pcie@1fa92000 {
> +            compatible = "airoha,an7583-pcie";
> +            device_type = "pci";
> +            linux,pci-domain = <1>;
> +            #address-cells = <3>;
> +            #size-cells = <2>;
> +
> +            reg = <0x0 0x1fa92000 0x0 0x1670>;
> +            reg-names = "port1";
> +
> +            clocks = <&scuclk EN7523_CLK_PCIE>;
> +            clock-names = "sys_ck1";
> +
> +            phys = <&pciephy>;
> +            phy-names = "pcie-phy1";
> +
> +            ranges = <0x02000000 0 0x24000000 0x0 0x24000000 0 0x4000000>;
> +
> +            resets = <&scuclk>; /* AN7583_PCIE1_RST */
> +            reset-names = "pcie-rst1";
> +
> +            mediatek,pbus-csr = <&pbus_csr 0x8 0xc>;
> +
> +            interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
> +            interrupt-names = "pcie_irq";
> +            bus-range = <0x00 0xff>;
> +            #interrupt-cells = <1>;
> +            interrupt-map-mask = <0 0 0 7>;
> +            interrupt-map = <0 0 0 1 &pcie_intc1 0>,
> +                            <0 0 0 2 &pcie_intc1 1>,
> +                            <0 0 0 3 &pcie_intc1 2>,
> +                            <0 0 0 4 &pcie_intc1 3>;
> +
> +            pcie_intc1_4: interrupt-controller {
> +                interrupt-controller;
> +                #address-cells = <0>;
> +                #interrupt-cells = <1>;
> +            };
> +        };
> +    };
> -- 
> 2.51.0
>