From: Gray Huang <gray.huang@wesion.com>
To: robh@kernel.org, krzk+dt@kernel.org, conor+dt@kernel.org,
heiko@sntech.de
Cc: devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-rockchip@lists.infradead.org, linux-kernel@vger.kernel.org,
nick@khadas.com, Gray Huang <gray.huang@wesion.com>
Subject: [PATCH 2/6] arm64: dts: rockchip: Add AP6275P wireless support for Khadas Edge 2L
Date: Wed, 25 Mar 2026 13:46:10 +0800 [thread overview]
Message-ID: <20260325054614.1497147-3-gray.huang@wesion.com> (raw)
In-Reply-To: <20260325054614.1497147-1-gray.huang@wesion.com>
The Khadas Edge 2L board uses the Ampak AP6275P (BCM43752) PCIe
Wi-Fi 6 module.
Enable the pcie0 controller and add the Wi-Fi module as its child
node. Additionally, enable the HYM8563 RTC to provide the 32.768kHz
LPO clock required by the Wi-Fi module, along with the necessary
CombPHY and fixed regulator.
Signed-off-by: Gray Huang <gray.huang@wesion.com>
---
.../dts/rockchip/rk3576-khadas-edge-2l.dts | 71 ++++++++++++++++++-
1 file changed, 70 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/rockchip/rk3576-khadas-edge-2l.dts b/arch/arm64/boot/dts/rockchip/rk3576-khadas-edge-2l.dts
index 5781deae00d9..09cb0f0d6dcf 100644
--- a/arch/arm64/boot/dts/rockchip/rk3576-khadas-edge-2l.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3576-khadas-edge-2l.dts
@@ -47,7 +47,19 @@ vcc_2v0_pldo_s3: regulator-vcc-2v0-pldo-s3 {
vin-supply = <&vcc_sys>;
};
-
+ vcc_wifi_reg_on: regulator-wifi-reg-on {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpios = <&gpio4 RK_PA2 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&wifi_reg_on>;
+ pinctrl-names = "default";
+ regulator-name = "wifi_reg_on";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_1v8_s3>;
+ };
};
&cpu_l0 {
@@ -431,6 +443,63 @@ regulator-state-mem {
};
};
+&combphy0_ps {
+ status = "okay";
+};
+
+&pcie0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie0_rst>;
+ reset-gpios = <&gpio4 RK_PB4 GPIO_ACTIVE_HIGH>;
+ vpcie3v3-supply = <&vcc_3v3_s3>;
+ status = "okay";
+
+ pcie@0,0 {
+ reg = <0x0 0 0 0 0>;
+ bus-range = <0x0 0xf>;
+ device_type = "pci";
+ ranges;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ wifi: wifi@0,0 {
+ compatible = "pci14e4,449d";
+ reg = <0x10000 0 0 0 0>;
+ clocks = <&hym8563>;
+ clock-names = "lpo";
+ };
+ };
+};
+
+&i2c2 {
+ status = "okay";
+
+ hym8563: hym8563@51 {
+ compatible = "haoyu,hym8563";
+ reg = <0x51>;
+ #clock-cells = <0>;
+ clock-output-names = "hym8563";
+ wakeup-source;
+ };
+};
+
+&pinctrl {
+ pcie0 {
+ pcie0_rst: pcie0-rst {
+ rockchip,pins = <4 RK_PB4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ wifi {
+ wifi_reg_on: wifi-reg-on {
+ rockchip,pins = <4 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+
+ wifi_wake_host: wifi-wake-host {
+ rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+ };
+};
&sdhci {
bus-width = <8>;
--
2.34.1
next prev parent reply other threads:[~2026-03-25 5:49 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-03-25 5:46 [PATCH 0/6] arm64: dts: rockchip: Add peripheral support for Khadas Edge 2L Gray Huang
2026-03-25 5:46 ` [PATCH 1/6] arm64: dts: rockchip: Add PMIC " Gray Huang
2026-03-25 5:46 ` Gray Huang [this message]
2026-04-27 12:25 ` [PATCH 2/6] arm64: dts: rockchip: Add AP6275P wireless " Heiko Stuebner
2026-03-25 5:46 ` [PATCH 3/6] arm64: dts: rockchip: Enable GPU " Gray Huang
2026-03-25 5:46 ` [PATCH 4/6] arm64: dts: rockchip: Add HDMI and VOP support " Gray Huang
2026-03-25 5:46 ` [PATCH 5/6] arm64: dts: rockchip: Enable USB " Gray Huang
2026-04-27 12:27 ` Heiko Stuebner
2026-04-29 6:49 ` Gray Huang
2026-03-25 5:46 ` [PATCH 6/6] arm64: dts: rockchip: Add Bluetooth support " Gray Huang
2026-04-27 12:27 ` Heiko Stuebner
2026-04-29 6:51 ` Gray Huang
2026-04-27 12:23 ` (subset) [PATCH 0/6] arm64: dts: rockchip: Add peripheral " Heiko Stuebner
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260325054614.1497147-3-gray.huang@wesion.com \
--to=gray.huang@wesion.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=heiko@sntech.de \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-rockchip@lists.infradead.org \
--cc=nick@khadas.com \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox