[PATCH v6 0/3] hwmon: emc2305: Support configurable fan PWM at shutdown

[PATCH v6 0/3] hwmon: emc2305: Support configurable fan PWM at shutdown

[florin.leotescu]

From: Florin Leotescu <florin.leotescu@nxp.com>

This series adds support for configuring the fan PWM duty cycle applied
during system shutdown for the EMC2305 fan controller.

Some platforms require fans to transition to a predefined safe state
during shutdown or reboot handoff until firmware or the next boot stage
reconfigures the controller.

The new optional Device Tree property "fan-shutdown-percent" allows the
shutdown PWM duty cycle to be configured per fan output.

Changes in v6:
- Split fan channel index validation into a separate patch.
  Validate fan channel index agains the number of available channels.
- Refine dt-binding commit message to refer to PWM duty cycle
  instead of fan speed.
Changes in v5:
- Add fan channel index bound check after reg property read 
  to prevent out-of-bounds access.
- Refine fan-shutdown-percent description.
Changes in v4:
- Initialize pwm_shudown array to EMC2305_PWM_SHUTDOWN_UNSET in probe,
  to avoid treating unconfigured channels as valid and written 0
  during shutdown
Changes in v3:
- Rebased on current upstream
- Dropped already upstreamed of_node_put(child) fix
Changes in v2:
- Address feedback from Guenter Roeck
- Make shutdown behavior configurable via Device Tree
- Add optional fan-shutdown-percent property
- Apply shutdown PWM only for channels defining the property

Florin Leotescu (3):
  hwmon: emc2305: Validate fan channel index
  dt-bindings: hwmon: emc2305: Add fan-shutdown-percent property
  hwmon: emc2305: Support configurable fan PWM at shutdown

 .../bindings/hwmon/microchip,emc2305.yaml     |  8 ++++
 drivers/hwmon/emc2305.c                       | 41 +++++++++++++++++++
 2 files changed, 49 insertions(+)

-- 
2.34.1

[PATCH v6 1/3] hwmon: emc2305: Validate fan channel index

[florin.leotescu]

From: Florin Leotescu <florin.leotescu@nxp.com>

The fan channel index is used to access per-channel data structures.
Validate the index agains the number of available channels
before use to prevent out-of-bounds access if an invalid
value is provided.

Signed-off-by: Florin Leotescu <florin.leotescu@nxp.com>
---
 drivers/hwmon/emc2305.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/drivers/hwmon/emc2305.c b/drivers/hwmon/emc2305.c
index 64b213e1451e..0b42b82c8e22 100644
--- a/drivers/hwmon/emc2305.c
+++ b/drivers/hwmon/emc2305.c
@@ -548,6 +548,12 @@ static int emc2305_of_parse_pwm_child(struct device *dev,
 		return ret;
 	}
 
+	if (ch >= data->pwm_num) {
+		dev_err(dev, "invalid reg %u for node %pOF (valid range 0-%u)\n", ch, child,
+			data->pwm_num - 1);
+		return -EINVAL;
+	}
+
 	ret = of_parse_phandle_with_args(child, "pwms", "#pwm-cells", 0, &args);
 
 	if (ret)
-- 
2.34.1

[PATCH v6 2/3] dt-bindings: hwmon: emc2305: Add fan-shutdown-percent property

[florin.leotescu]

From: Florin Leotescu <florin.leotescu@nxp.com>

The EMC2305 fan controller supports multiple independent PWM fan
outputs. Some systems require fans to enter a defined safe state
during system shutdown or reboot handoff, until firmware or the next
boot stage reconfigures the controller.

Add an optional "fan-shutdown-percent" property to fan child nodes
allowing the PWM duty cycle applied during shutdown to be configured
per fan output.

Signed-off-by: Florin Leotescu <florin.leotescu@nxp.com>
---
 .../devicetree/bindings/hwmon/microchip,emc2305.yaml      | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/Documentation/devicetree/bindings/hwmon/microchip,emc2305.yaml b/Documentation/devicetree/bindings/hwmon/microchip,emc2305.yaml
index d3f06ebc19fa..8c2548539d7f 100644
--- a/Documentation/devicetree/bindings/hwmon/microchip,emc2305.yaml
+++ b/Documentation/devicetree/bindings/hwmon/microchip,emc2305.yaml
@@ -54,6 +54,12 @@ patternProperties:
           The fan number used to determine the associated PWM channel.
         maxItems: 1
 
+      fan-shutdown-percent:
+        description:
+          PWM duty cycle in percent applied to the fan during shutdown.
+        minimum: 0
+        maximum: 100
+
     required:
       - reg
 
@@ -80,12 +86,14 @@ examples:
             fan@0 {
                 reg = <0x0>;
                 pwms = <&fan_controller 26000 PWM_POLARITY_INVERTED 1>;
+                fan-shutdown-percent = <100>;
                 #cooling-cells = <2>;
             };
 
             fan@1 {
                 reg = <0x1>;
                 pwms = <&fan_controller 26000 0 1>;
+                fan-shutdown-percent = <50>;
                 #cooling-cells = <2>;
             };
 
-- 
2.34.1

Re: [PATCH v6 2/3] dt-bindings: hwmon: emc2305: Add fan-shutdown-percent property

[Conor Dooley]

[-- Attachment #1: Type: text/plain, Size: 692 bytes --]

On Thu, Apr 02, 2026 at 03:25:13PM +0300, florin.leotescu@oss.nxp.com wrote:
> From: Florin Leotescu <florin.leotescu@nxp.com>
> 
> The EMC2305 fan controller supports multiple independent PWM fan
> outputs. Some systems require fans to enter a defined safe state
> during system shutdown or reboot handoff, until firmware or the next
> boot stage reconfigures the controller.
> 
> Add an optional "fan-shutdown-percent" property to fan child nodes
> allowing the PWM duty cycle applied during shutdown to be configured
> per fan output.
> 
> Signed-off-by: Florin Leotescu <florin.leotescu@nxp.com>

Acked-by: Conor Dooley <conor.dooley@microchip.com>
pw-bot: not-applicable

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

[PATCH v6 3/3] hwmon: emc2305: Support configurable fan PWM at shutdown

[florin.leotescu]

From: Florin Leotescu <florin.leotescu@nxp.com>

Some systems require fans to enter in a defined safe state during system
shutdown or reboot handoff.

Add support for the optional Device Tree property "fan-shutdown-percent"
to configure the shutdown PWM duty cycle per fan output.

If the property is present for a fan channel, the driver converts the
configured percentage value to the corresponding PWM duty cycle and
applies it during driver shutdown.

If the property is not present, the fan state remains unchanged.

Signed-off-by: Florin Leotescu <florin.leotescu@nxp.com>
---
 drivers/hwmon/emc2305.c | 35 +++++++++++++++++++++++++++++++++++
 1 file changed, 35 insertions(+)

diff --git a/drivers/hwmon/emc2305.c b/drivers/hwmon/emc2305.c
index 0b42b82c8e22..dec3a79933c1 100644
--- a/drivers/hwmon/emc2305.c
+++ b/drivers/hwmon/emc2305.c
@@ -32,6 +32,7 @@
 #define EMC2305_REG_DRIVE_PWM_OUT	0x2b
 #define EMC2305_OPEN_DRAIN		0x0
 #define EMC2305_PUSH_PULL		0x1
+#define EMC2305_PWM_SHUTDOWN_UNSET      -1
 
 #define EMC2305_PWM_DUTY2STATE(duty, max_state, pwm_max) \
 	DIV_ROUND_CLOSEST((duty) * (max_state), (pwm_max))
@@ -104,6 +105,7 @@ struct emc2305_cdev_data {
  * @pwm_output_mask: PWM output mask
  * @pwm_polarity_mask: PWM polarity mask
  * @pwm_separate: separate PWM settings for every channel
+ * @pwm_shutdown: Set shutdown PWM.
  * @pwm_min: array of minimum PWM per channel
  * @pwm_freq: array of PWM frequency per channel
  * @cdev_data: array of cooling devices data
@@ -116,6 +118,7 @@ struct emc2305_data {
 	u8 pwm_output_mask;
 	u8 pwm_polarity_mask;
 	bool pwm_separate;
+	s16 pwm_shutdown[EMC2305_PWM_MAX];
 	u8 pwm_min[EMC2305_PWM_MAX];
 	u16 pwm_freq[EMC2305_PWM_MAX];
 	struct emc2305_cdev_data cdev_data[EMC2305_PWM_MAX];
@@ -539,6 +542,7 @@ static int emc2305_of_parse_pwm_child(struct device *dev,
 				      struct device_node *child,
 				      struct emc2305_data *data)
 {	u32 ch;
+	u32 pwm_shutdown_percent;
 	int ret;
 	struct of_phandle_args args;
 
@@ -585,6 +589,16 @@ static int emc2305_of_parse_pwm_child(struct device *dev,
 	}
 
 	of_node_put(args.np);
+
+	ret = of_property_read_u32(child, "fan-shutdown-percent",
+				   &pwm_shutdown_percent);
+
+	if (!ret) {
+		pwm_shutdown_percent = clamp(pwm_shutdown_percent, 0, 100);
+		data->pwm_shutdown[ch] =
+			DIV_ROUND_CLOSEST(pwm_shutdown_percent * EMC2305_FAN_MAX, 100);
+	}
+
 	return 0;
 }
 
@@ -637,6 +651,9 @@ static int emc2305_probe(struct i2c_client *client)
 	if (ret)
 		return ret;
 
+	for (i = 0; i < EMC2305_PWM_MAX; i++)
+		data->pwm_shutdown[i] = EMC2305_PWM_SHUTDOWN_UNSET;
+
 	pwm_childs = emc2305_probe_childs_from_dt(dev);
 
 	pdata = dev_get_platdata(&client->dev);
@@ -720,6 +737,23 @@ static int emc2305_probe(struct i2c_client *client)
 	return 0;
 }
 
+static void emc2305_shutdown(struct i2c_client *client)
+{
+	int i;
+	int ret;
+	struct emc2305_data *data = i2c_get_clientdata(client);
+
+	for (i = 0; i < data->pwm_num; i++) {
+		if (data->pwm_shutdown[i] != EMC2305_PWM_SHUTDOWN_UNSET) {
+			ret = i2c_smbus_write_byte_data(client, EMC2305_REG_FAN_DRIVE(i),
+							data->pwm_shutdown[i]);
+			if (ret < 0)
+				dev_warn(&client->dev,
+					 "Failed to set shutdown PWM for ch %d\n", i);
+		}
+	}
+}
+
 static const struct of_device_id of_emc2305_match_table[] = {
 	{ .compatible = "microchip,emc2305", },
 	{},
@@ -732,6 +766,7 @@ static struct i2c_driver emc2305_driver = {
 		.of_match_table = of_emc2305_match_table,
 	},
 	.probe = emc2305_probe,
+	.shutdown = emc2305_shutdown,
 	.id_table = emc2305_ids,
 };
 
-- 
2.34.1