From: Yu-Chun Lin <eleanor.lin@realtek.com>
To: <mturquette@baylibre.com>, <sboyd@kernel.org>, <robh@kernel.org>,
<krzk+dt@kernel.org>, <conor+dt@kernel.org>,
<p.zabel@pengutronix.de>, <cylee12@realtek.com>,
<afaerber@suse.com>, <jyanchou@realtek.com>
Cc: <devicetree@vger.kernel.org>, <linux-clk@vger.kernel.org>,
<linux-kernel@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
<linux-realtek-soc@lists.infradead.org>, <james.tai@realtek.com>,
<cy.huang@realtek.com>, <stanley_chang@realtek.com>,
<eleanor.lin@realtek.com>, <bmasney@redhat.com>
Subject: [PATCH v7 07/10] clk: realtek: Add support for MMC-tuned PLL clocks
Date: Fri, 8 May 2026 19:16:38 +0800 [thread overview]
Message-ID: <20260508111641.3192177-8-eleanor.lin@realtek.com> (raw)
In-Reply-To: <20260508111641.3192177-1-eleanor.lin@realtek.com>
From: Cheng-Yu Lee <cylee12@realtek.com>
Add clk_pll_mmc_ops for enable/disable, prepare, rate control, and status
operations on MMC PLL clocks.
Also add clk_pll_mmc_phase_ops to support phase get/set operations.
Signed-off-by: Cheng-Yu Lee <cylee12@realtek.com>
Co-developed-by: Jyan Chou <jyanchou@realtek.com>
Signed-off-by: Jyan Chou <jyanchou@realtek.com>
Co-developed-by: Yu-Chun Lin <eleanor.lin@realtek.com>
Signed-off-by: Yu-Chun Lin <eleanor.lin@realtek.com>
---
MAINTAINERS | 8 +
drivers/clk/realtek/Kconfig | 3 +
drivers/clk/realtek/Makefile | 2 +
drivers/clk/realtek/clk-pll-mmc.c | 453 ++++++++++++++++++++++++++++++
drivers/clk/realtek/clk-pll.h | 13 +
5 files changed, 479 insertions(+)
create mode 100644 drivers/clk/realtek/clk-pll-mmc.c
diff --git a/MAINTAINERS b/MAINTAINERS
index b16d2c62ea3d..a1e19b5f247e 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -22439,6 +22439,14 @@ F: drivers/reset/realtek/*
F: include/dt-bindings/clock/realtek*
F: include/dt-bindings/reset/realtek*
+REALTEK SOC PLL CLOCK FOR MMC SUPPORT
+M: Cheng-Yu Lee <cylee12@realtek.com>
+M: Jyan Chou <jyanchou@realtek.com>
+M: Yu-Chun Lin <eleanor.lin@realtek.com>
+L: linux-clk@vger.kernel.org
+S: Supported
+F: drivers/clk/realtek/clk-pll-mmc.c
+
REALTEK SPI-NAND
M: Chris Packham <chris.packham@alliedtelesis.co.nz>
S: Maintained
diff --git a/drivers/clk/realtek/Kconfig b/drivers/clk/realtek/Kconfig
index 4e042e41f30d..9efd70094bd2 100644
--- a/drivers/clk/realtek/Kconfig
+++ b/drivers/clk/realtek/Kconfig
@@ -25,4 +25,7 @@ config RTK_CLK_COMMON
multiple Realtek clock implementations, and include integration
with reset controllers where required.
+config RTK_CLK_PLL_MMC
+ tristate
+
endif
diff --git a/drivers/clk/realtek/Makefile b/drivers/clk/realtek/Makefile
index f90dc57fcfdb..fd7d777902c8 100644
--- a/drivers/clk/realtek/Makefile
+++ b/drivers/clk/realtek/Makefile
@@ -7,3 +7,5 @@ clk-rtk-y += clk-pll.o
clk-rtk-y += clk-regmap-gate.o
clk-rtk-y += clk-regmap-mux.o
clk-rtk-y += freq_table.o
+
+clk-rtk-$(CONFIG_RTK_CLK_PLL_MMC) += clk-pll-mmc.o
diff --git a/drivers/clk/realtek/clk-pll-mmc.c b/drivers/clk/realtek/clk-pll-mmc.c
new file mode 100644
index 000000000000..998ab853ffbb
--- /dev/null
+++ b/drivers/clk/realtek/clk-pll-mmc.c
@@ -0,0 +1,453 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2021-2026 Realtek Semiconductor Corporation
+ * Author: Cheng-Yu Lee <cylee12@realtek.com>
+ */
+
+#include <linux/bits.h>
+#include <linux/export.h>
+#include <linux/module.h>
+#include <linux/regmap.h>
+#include "clk-pll.h"
+
+#define PLL_EMMC1_OFFSET 0x0
+#define PLL_EMMC2_OFFSET 0x4
+#define PLL_EMMC3_OFFSET 0x8
+#define PLL_EMMC4_OFFSET 0xc
+#define PLL_SSC_DIG_EMMC1_OFFSET 0x0
+#define PLL_SSC_DIG_EMMC3_OFFSET 0xc
+#define PLL_SSC_DIG_EMMC4_OFFSET 0x10
+
+#define PLL_MMC_SSC_DIV_N_VAL 0x1b
+
+#define PLL_PHRT0_MASK BIT(0)
+#define PLL_PHSEL_MASK GENMASK(4, 0)
+#define PLL_SSCPLL_RS_MASK GENMASK(12, 10)
+#define PLL_SSCPLL_ICP_MASK GENMASK(9, 5)
+#define PLL_SSC_DIV_EXT_F_MASK GENMASK(25, 13)
+#define PLL_PI_IBSELH_MASK GENMASK(28, 27)
+#define PLL_SSC_DIV_N_MASK GENMASK(23, 16)
+#define PLL_NCODE_SSC_EMMC_MASK GENMASK(20, 13)
+#define PLL_FCODE_SSC_EMMC_MASK GENMASK(12, 0)
+#define PLL_GRAN_EST_EM_MC_MASK GENMASK(20, 0)
+#define PLL_EN_SSC_EMMC_MASK BIT(0)
+#define PLL_FLAG_INITAL_EMMC_MASK BIT(8)
+
+#define PLL_PHRT0_SHIFT 1
+#define PLL_SSCPLL_RS_SHIFT 10
+#define PLL_SSCPLL_ICP_SHIFT 5
+#define PLL_SSC_DIV_EXT_F_SHIFT 13
+#define PLL_PI_IBSELH_SHIFT 27
+#define PLL_SSC_DIV_N_SHIFT 16
+#define PLL_NCODE_SSC_EMMC_SHIFT 13
+#define PLL_FLAG_INITAL_EMMC_SHIFT 8
+
+#define CYCLE_DEGREES 360
+#define PHASE_STEPS 32
+#define PHASE_SCALE_FACTOR 1125
+
+static inline struct clk_pll_mmc *to_clk_pll_mmc(struct clk_hw *hw)
+{
+ struct clk_regmap *clkr = to_clk_regmap(hw);
+
+ return container_of(clkr, struct clk_pll_mmc, clkr);
+}
+
+static inline int get_phrt0(struct clk_pll_mmc *clkm, u32 *val)
+{
+ u32 reg;
+ int ret;
+
+ ret = regmap_read(clkm->clkr.regmap, clkm->pll_ofs + PLL_EMMC1_OFFSET, ®);
+ if (ret)
+ return ret;
+
+ *val = (reg >> PLL_PHRT0_SHIFT) & PLL_PHRT0_MASK;
+
+ return 0;
+}
+
+static inline int set_phrt0(struct clk_pll_mmc *clkm, u32 val)
+{
+ return regmap_update_bits(clkm->clkr.regmap, clkm->pll_ofs + PLL_EMMC1_OFFSET,
+ PLL_PHRT0_MASK, val << PLL_PHRT0_SHIFT);
+}
+
+static inline int get_phsel(struct clk_pll_mmc *clkm, int id, u32 *val)
+{
+ u32 sft = id ? 8 : 3;
+ u32 raw_val;
+ int ret;
+
+ ret = regmap_read(clkm->clkr.regmap, clkm->pll_ofs + PLL_EMMC1_OFFSET, &raw_val);
+ if (ret)
+ return ret;
+
+ *val = (raw_val >> sft) & PLL_PHSEL_MASK;
+
+ return 0;
+}
+
+static inline int set_phsel(struct clk_pll_mmc *clkm, int id, u32 val)
+{
+ u32 sft = id ? 8 : 3;
+
+ return regmap_update_bits(clkm->clkr.regmap, clkm->pll_ofs + PLL_EMMC1_OFFSET,
+ PLL_PHSEL_MASK << sft, val << sft);
+}
+
+static inline int set_sscpll_rs(struct clk_pll_mmc *clkm, u32 val)
+{
+ return regmap_update_bits(clkm->clkr.regmap, clkm->pll_ofs + PLL_EMMC2_OFFSET,
+ PLL_SSCPLL_RS_MASK, val << PLL_SSCPLL_RS_SHIFT);
+}
+
+static inline int set_sscpll_icp(struct clk_pll_mmc *clkm, u32 val)
+{
+ return regmap_update_bits(clkm->clkr.regmap, clkm->pll_ofs + PLL_EMMC2_OFFSET,
+ PLL_SSCPLL_ICP_MASK, val << PLL_SSCPLL_ICP_SHIFT);
+}
+
+static inline int get_ssc_div_ext_f(struct clk_pll_mmc *clkm, u32 *val)
+{
+ u32 raw_val;
+ int ret;
+
+ ret = regmap_read(clkm->clkr.regmap, clkm->pll_ofs + PLL_EMMC2_OFFSET, &raw_val);
+ if (ret)
+ return ret;
+
+ *val = (raw_val & PLL_SSC_DIV_EXT_F_MASK) >> PLL_SSC_DIV_EXT_F_SHIFT;
+
+ return 0;
+}
+
+static inline int set_ssc_div_ext_f(struct clk_pll_mmc *clkm, u32 val)
+{
+ return regmap_update_bits(clkm->clkr.regmap, clkm->pll_ofs + PLL_EMMC2_OFFSET,
+ PLL_SSC_DIV_EXT_F_MASK,
+ val << PLL_SSC_DIV_EXT_F_SHIFT);
+}
+
+static inline int set_pi_ibselh(struct clk_pll_mmc *clkm, u32 val)
+{
+ return regmap_update_bits(clkm->clkr.regmap, clkm->pll_ofs + PLL_EMMC2_OFFSET,
+ PLL_PI_IBSELH_MASK, val << PLL_PI_IBSELH_SHIFT);
+}
+
+static inline int set_ssc_div_n(struct clk_pll_mmc *clkm, u32 val)
+{
+ return regmap_update_bits(clkm->clkr.regmap, clkm->pll_ofs + PLL_EMMC3_OFFSET,
+ PLL_SSC_DIV_N_MASK, val << PLL_SSC_DIV_N_SHIFT);
+}
+
+static inline int get_ssc_div_n(struct clk_pll_mmc *clkm, u32 *val)
+{
+ int ret;
+ u32 raw_val;
+
+ ret = regmap_read(clkm->clkr.regmap, clkm->pll_ofs + PLL_EMMC3_OFFSET, &raw_val);
+ if (ret)
+ return ret;
+
+ *val = (raw_val & PLL_SSC_DIV_N_MASK) >> PLL_SSC_DIV_N_SHIFT;
+
+ return 0;
+}
+
+static inline int set_pow_ctl(struct clk_pll_mmc *clkm, u32 val)
+{
+ return regmap_write(clkm->clkr.regmap, clkm->pll_ofs + PLL_EMMC4_OFFSET, val);
+}
+
+static inline int get_pow_ctl(struct clk_pll_mmc *clkm, u32 *val)
+{
+ int ret;
+ u32 raw_val;
+
+ ret = regmap_read(clkm->clkr.regmap, clkm->pll_ofs + PLL_EMMC4_OFFSET, &raw_val);
+ if (ret)
+ return ret;
+
+ *val = raw_val;
+
+ return 0;
+}
+
+static int clk_pll_mmc_phase_set_phase(struct clk_hw *hw, int degrees)
+{
+ struct clk_hw *hwp = clk_hw_get_parent(hw);
+ struct clk_pll_mmc *clkm;
+ int phase_id;
+ int ret;
+ u32 val;
+
+ if (!hwp)
+ return -ENOENT;
+
+ clkm = to_clk_pll_mmc(hwp);
+ phase_id = (hw == &clkm->phase0_hw) ? 0 : 1;
+ val = DIV_ROUND_CLOSEST(degrees * 100, PHASE_SCALE_FACTOR);
+ ret = set_phsel(clkm, phase_id, val);
+ if (ret)
+ return ret;
+
+ usleep_range(10, 20);
+
+ return 0;
+}
+
+static int clk_pll_mmc_phase_get_phase(struct clk_hw *hw)
+{
+ struct clk_hw *hwp;
+ struct clk_pll_mmc *clkm;
+ int phase_id;
+ int ret;
+ u32 val;
+
+ hwp = clk_hw_get_parent(hw);
+ if (!hwp)
+ return -ENOENT;
+
+ clkm = to_clk_pll_mmc(hwp);
+ phase_id = (hw - &clkm->phase0_hw) ? 1 : 0;
+ ret = get_phsel(clkm, phase_id, &val);
+ if (ret)
+ return ret;
+
+ val = DIV_ROUND_CLOSEST(val * CYCLE_DEGREES, PHASE_STEPS);
+
+ return val;
+}
+
+const struct clk_ops rtk_clk_pll_mmc_phase_ops = {
+ .set_phase = clk_pll_mmc_phase_set_phase,
+ .get_phase = clk_pll_mmc_phase_get_phase,
+};
+EXPORT_SYMBOL_NS_GPL(rtk_clk_pll_mmc_phase_ops, "REALTEK_CLK");
+
+static int clk_pll_mmc_prepare(struct clk_hw *hw)
+{
+ struct clk_pll_mmc *clkm = to_clk_pll_mmc(hw);
+
+ return set_pow_ctl(clkm, 7);
+}
+
+static void clk_pll_mmc_unprepare(struct clk_hw *hw)
+{
+ struct clk_pll_mmc *clkm = to_clk_pll_mmc(hw);
+
+ set_pow_ctl(clkm, 0);
+}
+
+static int clk_pll_mmc_is_prepared(struct clk_hw *hw)
+{
+ struct clk_pll_mmc *clkm = to_clk_pll_mmc(hw);
+ u32 val;
+ int ret;
+
+ ret = get_pow_ctl(clkm, &val);
+ if (ret)
+ return 1;
+
+ return val != 0x0;
+}
+
+static int clk_pll_mmc_enable(struct clk_hw *hw)
+{
+ struct clk_pll_mmc *clkm = to_clk_pll_mmc(hw);
+ int ret;
+
+ ret = set_phrt0(clkm, 1);
+ if (ret)
+ return ret;
+
+ udelay(10);
+
+ return 0;
+}
+
+static void clk_pll_mmc_disable(struct clk_hw *hw)
+{
+ struct clk_pll_mmc *clkm = to_clk_pll_mmc(hw);
+
+ set_phrt0(clkm, 0);
+ udelay(10);
+}
+
+static int clk_pll_mmc_is_enabled(struct clk_hw *hw)
+{
+ struct clk_pll_mmc *clkm = to_clk_pll_mmc(hw);
+ u32 val;
+ int ret;
+
+ ret = get_phrt0(clkm, &val);
+ if (ret)
+ return 1;
+
+ return val == 0x1;
+}
+
+static unsigned long clk_pll_mmc_recalc_rate(struct clk_hw *hw, unsigned long parent_rate)
+{
+ struct clk_pll_mmc *clkm = to_clk_pll_mmc(hw);
+ u32 val, ext_f;
+ int ret;
+
+ ret = get_ssc_div_n(clkm, &val);
+ if (ret)
+ return ret;
+
+ ret = get_ssc_div_ext_f(clkm, &ext_f);
+ if (ret)
+ return ret;
+
+ return parent_rate / 4 * (val + 2) + (parent_rate / 4 * ext_f) / 8192;
+}
+
+static int clk_pll_mmc_determine_rate(struct clk_hw *hw, struct clk_rate_request *req)
+{
+ u32 val;
+
+ if (!req->best_parent_rate)
+ return -EINVAL;
+
+ val = DIV_ROUND_CLOSEST(req->rate * 4, req->best_parent_rate);
+ req->rate = req->best_parent_rate * val / 4;
+
+ return 0;
+}
+
+static int clk_pll_mmc_set_rate(struct clk_hw *hw, unsigned long rate, unsigned long parent_rate)
+{
+ struct clk_pll_mmc *clkm = to_clk_pll_mmc(hw);
+ u32 val = PLL_MMC_SSC_DIV_N_VAL;
+ int ret;
+
+ ret = regmap_update_bits(clkm->clkr.regmap,
+ clkm->ssc_dig_ofs + PLL_SSC_DIG_EMMC1_OFFSET,
+ PLL_FLAG_INITAL_EMMC_MASK, 0x0 << PLL_FLAG_INITAL_EMMC_SHIFT);
+ if (ret)
+ return ret;
+
+ ret = set_ssc_div_n(clkm, val);
+ if (ret)
+ return ret;
+
+ ret = set_ssc_div_ext_f(clkm, 1517);
+ if (ret)
+ return ret;
+
+ switch (val) {
+ case 31 ... 46:
+ ret = set_pi_ibselh(clkm, 3);
+ if (ret)
+ return ret;
+
+ ret = set_sscpll_rs(clkm, 3);
+ if (ret)
+ return ret;
+
+ ret = set_sscpll_icp(clkm, 2);
+ if (ret)
+ return ret;
+ break;
+
+ case 20 ... 30:
+ ret = set_pi_ibselh(clkm, 2);
+ if (ret)
+ return ret;
+
+ ret = set_sscpll_rs(clkm, 3);
+ if (ret)
+ return ret;
+
+ ret = set_sscpll_icp(clkm, 1);
+ if (ret)
+ return ret;
+ break;
+
+ case 10 ... 19:
+ ret = set_pi_ibselh(clkm, 1);
+ if (ret)
+ return ret;
+
+ ret = set_sscpll_rs(clkm, 2);
+ if (ret)
+ return ret;
+
+ ret = set_sscpll_icp(clkm, 1);
+ if (ret)
+ return ret;
+ break;
+
+ case 5 ... 9:
+ ret = set_pi_ibselh(clkm, 0);
+ if (ret)
+ return ret;
+
+ ret = set_sscpll_rs(clkm, 2);
+ if (ret)
+ return ret;
+
+ ret = set_sscpll_icp(clkm, 0);
+ if (ret)
+ return ret;
+ break;
+ }
+
+ ret = regmap_update_bits(clkm->clkr.regmap,
+ clkm->ssc_dig_ofs + PLL_SSC_DIG_EMMC3_OFFSET,
+ PLL_NCODE_SSC_EMMC_MASK,
+ 27 << PLL_NCODE_SSC_EMMC_SHIFT);
+ if (ret)
+ return ret;
+
+ ret = regmap_update_bits(clkm->clkr.regmap,
+ clkm->ssc_dig_ofs + PLL_SSC_DIG_EMMC3_OFFSET,
+ PLL_FCODE_SSC_EMMC_MASK, 321);
+ if (ret)
+ return ret;
+
+ ret = regmap_update_bits(clkm->clkr.regmap,
+ clkm->ssc_dig_ofs + PLL_SSC_DIG_EMMC4_OFFSET,
+ PLL_GRAN_EST_EM_MC_MASK, 5985);
+ if (ret)
+ return ret;
+
+ ret = regmap_update_bits(clkm->clkr.regmap,
+ clkm->ssc_dig_ofs + PLL_SSC_DIG_EMMC1_OFFSET,
+ PLL_EN_SSC_EMMC_MASK, 0x1);
+ if (ret)
+ return ret;
+
+ ret = regmap_update_bits(clkm->clkr.regmap,
+ clkm->ssc_dig_ofs + PLL_SSC_DIG_EMMC1_OFFSET,
+ PLL_EN_SSC_EMMC_MASK, 0x0);
+ if (ret)
+ return ret;
+
+ ret = regmap_update_bits(clkm->clkr.regmap,
+ clkm->ssc_dig_ofs + PLL_SSC_DIG_EMMC1_OFFSET,
+ PLL_FLAG_INITAL_EMMC_MASK,
+ 0x1 << PLL_FLAG_INITAL_EMMC_SHIFT);
+ if (ret)
+ return ret;
+
+ usleep_range(10, 20);
+
+ return 0;
+}
+
+const struct clk_ops rtk_clk_pll_mmc_ops = {
+ .prepare = clk_pll_mmc_prepare,
+ .unprepare = clk_pll_mmc_unprepare,
+ .is_prepared = clk_pll_mmc_is_prepared,
+ .enable = clk_pll_mmc_enable,
+ .disable = clk_pll_mmc_disable,
+ .is_enabled = clk_pll_mmc_is_enabled,
+ .recalc_rate = clk_pll_mmc_recalc_rate,
+ .determine_rate = clk_pll_mmc_determine_rate,
+ .set_rate = clk_pll_mmc_set_rate,
+};
+EXPORT_SYMBOL_NS_GPL(rtk_clk_pll_mmc_ops, "REALTEK_CLK");
diff --git a/drivers/clk/realtek/clk-pll.h b/drivers/clk/realtek/clk-pll.h
index 237b1d8a2f00..6bf4e02321f9 100644
--- a/drivers/clk/realtek/clk-pll.h
+++ b/drivers/clk/realtek/clk-pll.h
@@ -45,4 +45,17 @@ struct clk_pll {
extern const struct clk_ops rtk_clk_pll_ops;
extern const struct clk_ops rtk_clk_pll_ro_ops;
+struct clk_pll_mmc {
+ struct clk_regmap clkr;
+ unsigned int pll_ofs;
+ unsigned int ssc_dig_ofs;
+ struct clk_hw phase0_hw;
+ struct clk_hw phase1_hw;
+};
+
+#define __clk_pll_mmc_hw(_ptr) __clk_regmap_hw(&(_ptr)->clkr)
+
+extern const struct clk_ops rtk_clk_pll_mmc_ops;
+extern const struct clk_ops rtk_clk_pll_mmc_phase_ops;
+
#endif /* __CLK_REALTEK_CLK_PLL_H */
--
2.34.1
next prev parent reply other threads:[~2026-05-08 11:30 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-05-08 11:16 [PATCH v7 00/10] clk: realtek: Add RTD1625 clock support Yu-Chun Lin
2026-05-08 11:16 ` [PATCH v7 01/10] dt-bindings: clock: Add Realtek RTD1625 Clock & Reset Controller Yu-Chun Lin
2026-05-08 11:16 ` [PATCH v7 02/10] reset: Add Realtek basic reset support Yu-Chun Lin
2026-05-08 11:16 ` [PATCH v7 03/10] clk: realtek: Introduce a common probe() Yu-Chun Lin
2026-05-08 11:16 ` [PATCH v7 04/10] clk: realtek: Add support for phase locked loops (PLLs) Yu-Chun Lin
2026-05-08 11:16 ` [PATCH v7 05/10] clk: realtek: Add support for gate clock Yu-Chun Lin
2026-05-08 11:16 ` [PATCH v7 06/10] clk: realtek: Add support for mux clock Yu-Chun Lin
2026-05-08 11:16 ` Yu-Chun Lin [this message]
2026-05-08 11:16 ` [PATCH v7 08/10] clk: realtek: Add RTD1625-CRT clock controller driver Yu-Chun Lin
2026-05-08 11:16 ` [PATCH v7 09/10] clk: realtek: Add RTD1625-ISO " Yu-Chun Lin
2026-05-08 11:16 ` [PATCH v7 10/10] arm64: dts: realtek: Add clock support for RTD1625 Yu-Chun Lin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260508111641.3192177-8-eleanor.lin@realtek.com \
--to=eleanor.lin@realtek.com \
--cc=afaerber@suse.com \
--cc=bmasney@redhat.com \
--cc=conor+dt@kernel.org \
--cc=cy.huang@realtek.com \
--cc=cylee12@realtek.com \
--cc=devicetree@vger.kernel.org \
--cc=james.tai@realtek.com \
--cc=jyanchou@realtek.com \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-realtek-soc@lists.infradead.org \
--cc=mturquette@baylibre.com \
--cc=p.zabel@pengutronix.de \
--cc=robh@kernel.org \
--cc=sboyd@kernel.org \
--cc=stanley_chang@realtek.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox