From: Cosmo Chou <chou.cosmo@gmail.com>
To: robh@kernel.org, krzk+dt@kernel.org, conor+dt@kernel.org,
joel@jms.id.au, andrew@codeconstruct.com.au
Cc: devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-aspeed@lists.ozlabs.org, linux-kernel@vger.kernel.org,
cosmo.chou@quantatw.com, Cosmo Chou <chou.cosmo@gmail.com>
Subject: [PATCH v2 1/4] ARM: dts: aspeed: bletchley: Sort i2c device nodes by address
Date: Wed, 29 Jul 2026 19:43:09 +0800 [thread overview]
Message-ID: <20260729114312.3947300-2-chou.cosmo@gmail.com> (raw)
In-Reply-To: <20260729114312.3947300-1-chou.cosmo@gmail.com>
Reorder child nodes in i2c0-i2c6 to follow ascending unit address
ordering as required by scripts/dtc/dt-check-style. No functional
changes.
Signed-off-by: Cosmo Chou <chou.cosmo@gmail.com>
---
.../aspeed/aspeed-bmc-facebook-bletchley.dts | 430 +++++++++---------
1 file changed, 218 insertions(+), 212 deletions(-)
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-bletchley.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-bletchley.dts
index d1a04b63df9e..b022bdd02c1e 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-bletchley.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-bletchley.dts
@@ -343,10 +343,25 @@ flash@0 {
&i2c0 {
status = "okay";
- ina230@45 {
- compatible = "ti,ina230";
- reg = <0x45>;
- shunt-resistor = <2000>;
+
+ sled1_fusb302: typec-portc@22 {
+ compatible = "fcs,fusb302";
+ reg = <0x22>;
+
+ interrupt-parent = <&gpio0>;
+ interrupts = <ASPEED_GPIO(B, 0) IRQ_TYPE_LEVEL_LOW>;
+ vbus-supply = <&vbus_sled1>;
+
+ connector {
+ compatible = "usb-c-connector";
+ label = "USB-C";
+ pd-revision = /bits/ 8 <0x2 0x0 0x1 0x20>;
+ power-role = "dual";
+ data-role = "dual";
+ source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+ sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+ op-sink-microwatt = <10000000>;
+ };
};
mp5023@40 {
@@ -354,11 +369,6 @@ mp5023@40 {
reg = <0x40>;
};
- tmp421@4f {
- compatible = "ti,tmp421";
- reg = <0x4f>;
- };
-
sled1_ioexp41: pca9536@41 {
compatible = "nxp,pca9536";
reg = <0x41>;
@@ -370,20 +380,20 @@ sled1_ioexp41: pca9536@41 {
"SLED1_CLKREQ_N", "SLED1_PCIE_PWR_EN";
};
- sled1_ioexp: pca9539@76 {
- compatible = "nxp,pca9539";
- reg = <0x76>;
- gpio-controller;
- #gpio-cells = <2>;
+ ina230@45 {
+ compatible = "ti,ina230";
+ reg = <0x45>;
+ shunt-resistor = <2000>;
+ };
- interrupt-parent = <&gpio0>;
- interrupts = <ASPEED_GPIO(M, 0) IRQ_TYPE_LEVEL_LOW>;
+ tmp421@4f {
+ compatible = "ti,tmp421";
+ reg = <0x4f>;
+ };
- gpio-line-names =
- "SLED1_MS_DETECT1","SLED1_VBUS_BMC_EN","SLED1_INA230_ALERT","SLED1_P12V_STBY_ALERT",
- "SLED1_SSD_ALERT","SLED1_MS_DETECT0","SLED1_RST_CCG5","SLED1_FUSB302_INT",
- "SLED1_MD_STBY_RESET","SLED1_MD_IOEXP_EN_FAULT","SLED1_MD_DIR","SLED1_MD_DECAY",
- "SLED1_MD_MODE1","SLED1_MD_MODE2","SLED1_MD_MODE3","power-host1";
+ eeprom@54 {
+ compatible = "atmel,24c64";
+ reg = <0x54>;
};
sled1_leds: pca9552@67 {
@@ -401,13 +411,33 @@ sled1_leds: pca9552@67 {
"","","","";
};
- sled1_fusb302: typec-portc@22 {
+ sled1_ioexp: pca9539@76 {
+ compatible = "nxp,pca9539";
+ reg = <0x76>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-parent = <&gpio0>;
+ interrupts = <ASPEED_GPIO(M, 0) IRQ_TYPE_LEVEL_LOW>;
+
+ gpio-line-names =
+ "SLED1_MS_DETECT1","SLED1_VBUS_BMC_EN","SLED1_INA230_ALERT","SLED1_P12V_STBY_ALERT",
+ "SLED1_SSD_ALERT","SLED1_MS_DETECT0","SLED1_RST_CCG5","SLED1_FUSB302_INT",
+ "SLED1_MD_STBY_RESET","SLED1_MD_IOEXP_EN_FAULT","SLED1_MD_DIR","SLED1_MD_DECAY",
+ "SLED1_MD_MODE1","SLED1_MD_MODE2","SLED1_MD_MODE3","power-host1";
+ };
+};
+
+&i2c1 {
+ status = "okay";
+
+ sled2_fusb302: typec-portc@22 {
compatible = "fcs,fusb302";
reg = <0x22>;
interrupt-parent = <&gpio0>;
- interrupts = <ASPEED_GPIO(B, 0) IRQ_TYPE_LEVEL_LOW>;
- vbus-supply = <&vbus_sled1>;
+ interrupts = <ASPEED_GPIO(B, 1) IRQ_TYPE_LEVEL_LOW>;
+ vbus-supply = <&vbus_sled2>;
connector {
compatible = "usb-c-connector";
@@ -421,39 +451,51 @@ connector {
};
};
- eeprom@54 {
- compatible = "atmel,24c64";
- reg = <0x54>;
+ mp5023@40 {
+ compatible = "mps,mp5023";
+ reg = <0x40>;
+ };
+
+ sled2_ioexp41: pca9536@41 {
+ compatible = "nxp,pca9536";
+ reg = <0x41>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ gpio-line-names =
+ "SLED2_SWD_MUX", "SLED2_XRES_SWD_N",
+ "SLED2_CLKREQ_N", "SLED2_PCIE_PWR_EN";
};
-};
-&i2c1 {
- status = "okay";
ina230@45 {
compatible = "ti,ina230";
reg = <0x45>;
shunt-resistor = <2000>;
};
- mp5023@40 {
- compatible = "mps,mp5023";
- reg = <0x40>;
- };
-
tmp421@4f {
compatible = "ti,tmp421";
reg = <0x4f>;
};
- sled2_ioexp41: pca9536@41 {
- compatible = "nxp,pca9536";
- reg = <0x41>;
+ eeprom@54 {
+ compatible = "atmel,24c64";
+ reg = <0x54>;
+ };
+
+ sled2_leds: pca9552@67 {
+ compatible = "nxp,pca9552";
+ reg = <0x67>;
+ #address-cells = <1>;
+ #size-cells = <0>;
gpio-controller;
#gpio-cells = <2>;
gpio-line-names =
- "SLED2_SWD_MUX", "SLED2_XRES_SWD_N",
- "SLED2_CLKREQ_N", "SLED2_PCIE_PWR_EN";
+ "led-sled2-amber","led-sled2-blue","SLED2_RST_IOEXP","SLED2_MD_REF_PWM",
+ "","","","",
+ "","","","",
+ "","","","";
};
sled2_ioexp: pca9539@76 {
@@ -471,29 +513,18 @@ sled2_ioexp: pca9539@76 {
"SLED2_MD_STBY_RESET","SLED2_MD_IOEXP_EN_FAULT","SLED2_MD_DIR","SLED2_MD_DECAY",
"SLED2_MD_MODE1","SLED2_MD_MODE2","SLED2_MD_MODE3","power-host2";
};
+};
- sled2_leds: pca9552@67 {
- compatible = "nxp,pca9552";
- reg = <0x67>;
- #address-cells = <1>;
- #size-cells = <0>;
- gpio-controller;
- #gpio-cells = <2>;
-
- gpio-line-names =
- "led-sled2-amber","led-sled2-blue","SLED2_RST_IOEXP","SLED2_MD_REF_PWM",
- "","","","",
- "","","","",
- "","","","";
- };
+&i2c2 {
+ status = "okay";
- sled2_fusb302: typec-portc@22 {
+ sled3_fusb302: typec-portc@22 {
compatible = "fcs,fusb302";
reg = <0x22>;
interrupt-parent = <&gpio0>;
- interrupts = <ASPEED_GPIO(B, 1) IRQ_TYPE_LEVEL_LOW>;
- vbus-supply = <&vbus_sled2>;
+ interrupts = <ASPEED_GPIO(B, 7) IRQ_TYPE_LEVEL_LOW>;
+ vbus-supply = <&vbus_sled3>;
connector {
compatible = "usb-c-connector";
@@ -507,39 +538,51 @@ connector {
};
};
- eeprom@54 {
- compatible = "atmel,24c64";
- reg = <0x54>;
+ mp5023@40 {
+ compatible = "mps,mp5023";
+ reg = <0x40>;
+ };
+
+ sled3_ioexp41: pca9536@41 {
+ compatible = "nxp,pca9536";
+ reg = <0x41>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ gpio-line-names =
+ "SLED3_SWD_MUX", "SLED3_XRES_SWD_N",
+ "SLED3_CLKREQ_N", "SLED3_PCIE_PWR_EN";
};
-};
-&i2c2 {
- status = "okay";
ina230@45 {
compatible = "ti,ina230";
reg = <0x45>;
shunt-resistor = <2000>;
};
- mp5023@40 {
- compatible = "mps,mp5023";
- reg = <0x40>;
- };
-
tmp421@4f {
compatible = "ti,tmp421";
reg = <0x4f>;
};
- sled3_ioexp41: pca9536@41 {
- compatible = "nxp,pca9536";
- reg = <0x41>;
+ eeprom@54 {
+ compatible = "atmel,24c64";
+ reg = <0x54>;
+ };
+
+ sled3_leds: pca9552@67 {
+ compatible = "nxp,pca9552";
+ reg = <0x67>;
+ #address-cells = <1>;
+ #size-cells = <0>;
gpio-controller;
#gpio-cells = <2>;
gpio-line-names =
- "SLED3_SWD_MUX", "SLED3_XRES_SWD_N",
- "SLED3_CLKREQ_N", "SLED3_PCIE_PWR_EN";
+ "led-sled3-amber","led-sled3-blue","SLED3_RST_IOEXP","SLED3_MD_REF_PWM",
+ "","","","",
+ "","","","",
+ "","","","";
};
sled3_ioexp: pca9539@76 {
@@ -557,29 +600,18 @@ sled3_ioexp: pca9539@76 {
"SLED3_MD_STBY_RESET","SLED3_MD_IOEXP_EN_FAULT","SLED3_MD_DIR","SLED3_MD_DECAY",
"SLED3_MD_MODE1","SLED3_MD_MODE2","SLED3_MD_MODE3","power-host3";
};
+};
- sled3_leds: pca9552@67 {
- compatible = "nxp,pca9552";
- reg = <0x67>;
- #address-cells = <1>;
- #size-cells = <0>;
- gpio-controller;
- #gpio-cells = <2>;
-
- gpio-line-names =
- "led-sled3-amber","led-sled3-blue","SLED3_RST_IOEXP","SLED3_MD_REF_PWM",
- "","","","",
- "","","","",
- "","","","";
- };
+&i2c3 {
+ status = "okay";
- sled3_fusb302: typec-portc@22 {
+ sled4_fusb302: typec-portc@22 {
compatible = "fcs,fusb302";
reg = <0x22>;
interrupt-parent = <&gpio0>;
- interrupts = <ASPEED_GPIO(B, 7) IRQ_TYPE_LEVEL_LOW>;
- vbus-supply = <&vbus_sled3>;
+ interrupts = <ASPEED_GPIO(S, 7) IRQ_TYPE_LEVEL_LOW>;
+ vbus-supply = <&vbus_sled4>;
connector {
compatible = "usb-c-connector";
@@ -593,39 +625,51 @@ connector {
};
};
- eeprom@54 {
- compatible = "atmel,24c64";
- reg = <0x54>;
+ mp5023@40 {
+ compatible = "mps,mp5023";
+ reg = <0x40>;
+ };
+
+ sled4_ioexp41: pca9536@41 {
+ compatible = "nxp,pca9536";
+ reg = <0x41>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ gpio-line-names =
+ "SLED4_SWD_MUX", "SLED4_XRES_SWD_N",
+ "SLED4_CLKREQ_N", "SLED4_PCIE_PWR_EN";
};
-};
-&i2c3 {
- status = "okay";
ina230@45 {
compatible = "ti,ina230";
reg = <0x45>;
shunt-resistor = <2000>;
};
- mp5023@40 {
- compatible = "mps,mp5023";
- reg = <0x40>;
- };
-
tmp421@4f {
compatible = "ti,tmp421";
reg = <0x4f>;
};
- sled4_ioexp41: pca9536@41 {
- compatible = "nxp,pca9536";
- reg = <0x41>;
+ eeprom@54 {
+ compatible = "atmel,24c64";
+ reg = <0x54>;
+ };
+
+ sled4_leds: pca9552@67 {
+ compatible = "nxp,pca9552";
+ reg = <0x67>;
+ #address-cells = <1>;
+ #size-cells = <0>;
gpio-controller;
#gpio-cells = <2>;
gpio-line-names =
- "SLED4_SWD_MUX", "SLED4_XRES_SWD_N",
- "SLED4_CLKREQ_N", "SLED4_PCIE_PWR_EN";
+ "led-sled4-amber","led-sled4-blue","SLED4_RST_IOEXP","SLED4_MD_REF_PWM",
+ "","","","",
+ "","","","",
+ "","","","";
};
sled4_ioexp: pca9539@76 {
@@ -643,29 +687,18 @@ sled4_ioexp: pca9539@76 {
"SLED4_MD_STBY_RESET","SLED4_MD_IOEXP_EN_FAULT","SLED4_MD_DIR","SLED4_MD_DECAY",
"SLED4_MD_MODE1","SLED4_MD_MODE2","SLED4_MD_MODE3","power-host4";
};
+};
- sled4_leds: pca9552@67 {
- compatible = "nxp,pca9552";
- reg = <0x67>;
- #address-cells = <1>;
- #size-cells = <0>;
- gpio-controller;
- #gpio-cells = <2>;
-
- gpio-line-names =
- "led-sled4-amber","led-sled4-blue","SLED4_RST_IOEXP","SLED4_MD_REF_PWM",
- "","","","",
- "","","","",
- "","","","";
- };
+&i2c4 {
+ status = "okay";
- sled4_fusb302: typec-portc@22 {
+ sled5_fusb302: typec-portc@22 {
compatible = "fcs,fusb302";
reg = <0x22>;
interrupt-parent = <&gpio0>;
- interrupts = <ASPEED_GPIO(S, 7) IRQ_TYPE_LEVEL_LOW>;
- vbus-supply = <&vbus_sled4>;
+ interrupts = <ASPEED_GPIO(Y, 3) IRQ_TYPE_LEVEL_LOW>;
+ vbus-supply = <&vbus_sled5>;
connector {
compatible = "usb-c-connector";
@@ -679,39 +712,51 @@ connector {
};
};
- eeprom@54 {
- compatible = "atmel,24c64";
- reg = <0x54>;
+ mp5023@40 {
+ compatible = "mps,mp5023";
+ reg = <0x40>;
+ };
+
+ sled5_ioexp41: pca9536@41 {
+ compatible = "nxp,pca9536";
+ reg = <0x41>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ gpio-line-names =
+ "SLED5_SWD_MUX", "SLED5_XRES_SWD_N",
+ "SLED5_CLKREQ_N", "SLED5_PCIE_PWR_EN";
};
-};
-&i2c4 {
- status = "okay";
ina230@45 {
compatible = "ti,ina230";
reg = <0x45>;
shunt-resistor = <2000>;
};
- mp5023@40 {
- compatible = "mps,mp5023";
- reg = <0x40>;
- };
-
tmp421@4f {
compatible = "ti,tmp421";
reg = <0x4f>;
};
- sled5_ioexp41: pca9536@41 {
- compatible = "nxp,pca9536";
- reg = <0x41>;
+ eeprom@54 {
+ compatible = "atmel,24c64";
+ reg = <0x54>;
+ };
+
+ sled5_leds: pca9552@67 {
+ compatible = "nxp,pca9552";
+ reg = <0x67>;
+ #address-cells = <1>;
+ #size-cells = <0>;
gpio-controller;
#gpio-cells = <2>;
gpio-line-names =
- "SLED5_SWD_MUX", "SLED5_XRES_SWD_N",
- "SLED5_CLKREQ_N", "SLED5_PCIE_PWR_EN";
+ "led-sled5-amber","led-sled5-blue","SLED5_RST_IOEXP","SLED5_MD_REF_PWM",
+ "","","","",
+ "","","","",
+ "","","","";
};
sled5_ioexp: pca9539@76 {
@@ -729,29 +774,18 @@ sled5_ioexp: pca9539@76 {
"SLED5_MD_STBY_RESET","SLED5_MD_IOEXP_EN_FAULT","SLED5_MD_DIR","SLED5_MD_DECAY",
"SLED5_MD_MODE1","SLED5_MD_MODE2","SLED5_MD_MODE3","power-host5";
};
+};
- sled5_leds: pca9552@67 {
- compatible = "nxp,pca9552";
- reg = <0x67>;
- #address-cells = <1>;
- #size-cells = <0>;
- gpio-controller;
- #gpio-cells = <2>;
-
- gpio-line-names =
- "led-sled5-amber","led-sled5-blue","SLED5_RST_IOEXP","SLED5_MD_REF_PWM",
- "","","","",
- "","","","",
- "","","","";
- };
+&i2c5 {
+ status = "okay";
- sled5_fusb302: typec-portc@22 {
+ sled6_fusb302: typec-portc@22 {
compatible = "fcs,fusb302";
reg = <0x22>;
interrupt-parent = <&gpio0>;
- interrupts = <ASPEED_GPIO(Y, 3) IRQ_TYPE_LEVEL_LOW>;
- vbus-supply = <&vbus_sled5>;
+ interrupts = <ASPEED_GPIO(I, 7) IRQ_TYPE_LEVEL_LOW>;
+ vbus-supply = <&vbus_sled6>;
connector {
compatible = "usb-c-connector";
@@ -765,30 +799,11 @@ connector {
};
};
- eeprom@54 {
- compatible = "atmel,24c64";
- reg = <0x54>;
- };
-};
-
-&i2c5 {
- status = "okay";
- ina230@45 {
- compatible = "ti,ina230";
- reg = <0x45>;
- shunt-resistor = <2000>;
- };
-
mp5023@40 {
compatible = "mps,mp5023";
reg = <0x40>;
};
- tmp421@4f {
- compatible = "ti,tmp421";
- reg = <0x4f>;
- };
-
sled6_ioexp41: pca9536@41 {
compatible = "nxp,pca9536";
reg = <0x41>;
@@ -800,20 +815,20 @@ sled6_ioexp41: pca9536@41 {
"SLED6_CLKREQ_N", "SLED6_PCIE_PWR_EN";
};
- sled6_ioexp: pca9539@76 {
- compatible = "nxp,pca9539";
- reg = <0x76>;
- gpio-controller;
- #gpio-cells = <2>;
+ ina230@45 {
+ compatible = "ti,ina230";
+ reg = <0x45>;
+ shunt-resistor = <2000>;
+ };
- interrupt-parent = <&gpio0>;
- interrupts = <ASPEED_GPIO(M, 5) IRQ_TYPE_LEVEL_LOW>;
+ tmp421@4f {
+ compatible = "ti,tmp421";
+ reg = <0x4f>;
+ };
- gpio-line-names =
- "SLED6_MS_DETECT1","SLED6_VBUS_BMC_EN","SLED6_INA230_ALERT","SLED6_P12V_STBY_ALERT",
- "SLED6_SSD_ALERT","SLED6_MS_DETECT0","SLED6_RST_CCG5","SLED6_FUSB302_INT",
- "SLED6_MD_STBY_RESET","SLED6_MD_IOEXP_EN_FAULT","SLED6_MD_DIR","SLED6_MD_DECAY",
- "SLED6_MD_MODE1","SLED6_MD_MODE2","SLED6_MD_MODE3","power-host6";
+ eeprom@54 {
+ compatible = "atmel,24c64";
+ reg = <0x54>;
};
sled6_leds: pca9552@67 {
@@ -831,45 +846,36 @@ sled6_leds: pca9552@67 {
"","","","";
};
- sled6_fusb302: typec-portc@22 {
- compatible = "fcs,fusb302";
- reg = <0x22>;
+ sled6_ioexp: pca9539@76 {
+ compatible = "nxp,pca9539";
+ reg = <0x76>;
+ gpio-controller;
+ #gpio-cells = <2>;
interrupt-parent = <&gpio0>;
- interrupts = <ASPEED_GPIO(I, 7) IRQ_TYPE_LEVEL_LOW>;
- vbus-supply = <&vbus_sled6>;
-
- connector {
- compatible = "usb-c-connector";
- label = "USB-C";
- pd-revision = /bits/ 8 <0x2 0x0 0x1 0x20>;
- power-role = "dual";
- data-role = "dual";
- source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
- sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
- op-sink-microwatt = <10000000>;
- };
- };
+ interrupts = <ASPEED_GPIO(M, 5) IRQ_TYPE_LEVEL_LOW>;
- eeprom@54 {
- compatible = "atmel,24c64";
- reg = <0x54>;
+ gpio-line-names =
+ "SLED6_MS_DETECT1","SLED6_VBUS_BMC_EN","SLED6_INA230_ALERT","SLED6_P12V_STBY_ALERT",
+ "SLED6_SSD_ALERT","SLED6_MS_DETECT0","SLED6_RST_CCG5","SLED6_FUSB302_INT",
+ "SLED6_MD_STBY_RESET","SLED6_MD_IOEXP_EN_FAULT","SLED6_MD_DIR","SLED6_MD_DECAY",
+ "SLED6_MD_MODE1","SLED6_MD_MODE2","SLED6_MD_MODE3","power-host6";
};
};
&i2c6 {
status = "okay";
- eeprom@56 {
- compatible = "atmel,24c64";
- reg = <0x56>;
- };
-
rtc@51 {
/* in-chip rtc disabled, use external rtc (battery-backed) */
compatible = "nxp,pcf85263";
reg = <0x51>;
};
+
+ eeprom@56 {
+ compatible = "atmel,24c64";
+ reg = <0x56>;
+ };
};
&i2c7 {
--
2.43.0
next prev parent reply other threads:[~2026-07-29 11:43 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-07-29 11:43 [PATCH v2 0/4] ARM: dts: aspeed: bletchley: Cleanups and second source devices Cosmo Chou
2026-07-29 11:43 ` Cosmo Chou [this message]
2026-07-29 11:43 ` [PATCH v2 2/4] ARM: dts: aspeed: bletchley: Fix style warnings Cosmo Chou
2026-07-29 11:43 ` [PATCH v2 3/4] ARM: dts: aspeed: bletchley: Add second source PCA9532 LED controllers Cosmo Chou
2026-07-29 11:43 ` [PATCH v2 4/4] ARM: dts: aspeed: bletchley: Add second source ISL1208 RTC Cosmo Chou
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260729114312.3947300-2-chou.cosmo@gmail.com \
--to=chou.cosmo@gmail.com \
--cc=andrew@codeconstruct.com.au \
--cc=conor+dt@kernel.org \
--cc=cosmo.chou@quantatw.com \
--cc=devicetree@vger.kernel.org \
--cc=joel@jms.id.au \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-aspeed@lists.ozlabs.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox