[PATCH 6/8] arm64: dts: st: add ADC nodes on stm32mp231

[Fabrice Gasnier <fabrice.gasnier@foss.st.com>]

From: Cheick Traore <cheick.traore@foss.st.com>

Add analog-to-digital converter support on STM32MP23 SoC. It has 3 ADCs,
split into two blocks:
- ADC12 (ADC1 & ADC2) are tightly coupled.
- ADC3 is managed independently.
Define internal voltage channels in the SOC dtsi file, exception made of
vbat/4 channel (to avoid undesired load on it, in case no conversion is
needed on this channel). Choice is let to board implementation (via DT)
to define it.

Signed-off-by: Cheick Traore <cheick.traore@foss.st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
---
 arch/arm64/boot/dts/st/stm32mp231.dtsi | 113 +++++++++++++++++++++++++++++++++
 1 file changed, 113 insertions(+)

diff --git a/arch/arm64/boot/dts/st/stm32mp231.dtsi b/arch/arm64/boot/dts/st/stm32mp231.dtsi
index 959500140d98..3aa1efdf9402 100644
--- a/arch/arm64/boot/dts/st/stm32mp231.dtsi
+++ b/arch/arm64/boot/dts/st/stm32mp231.dtsi
@@ -646,6 +646,119 @@ uart7: serial@40370000 {
 				status = "disabled";
 			};
 
+			adc_12: adc@404e0000 {
+				compatible = "st,stm32mp23-adc-core", "st,stm32-adc-core";
+				reg = <0x404e0000 0x400>;
+				interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc CK_KER_ADC12>;
+				clock-names = "adc";
+				interrupt-controller;
+				#interrupt-cells = <1>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				access-controllers = <&rifsc 58>;
+				status = "disabled";
+
+				adc1: adc@0 {
+					compatible = "st,stm32mp23-adc", "st,stm32-adc";
+					reg = <0x0>;
+					interrupt-parent = <&adc_12>;
+					interrupts = <0>;
+					dmas = <&hpdma 81 0x20 0x12>;
+					dma-names = "rx";
+					#io-channel-cells = <1>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					nvmem-cells = <&vrefint>;
+					nvmem-cell-names = "vrefint";
+					st,adc-trigger-sel = <0>;
+					status = "disabled";
+					channel@14 {
+						reg = <14>;
+						label = "vrefint";
+					};
+				};
+
+				adc2: adc@100 {
+					compatible = "st,stm32mp23-adc", "st,stm32-adc";
+					reg = <0x100>;
+					interrupt-parent = <&adc_12>;
+					interrupts = <1>;
+					dmas = <&hpdma 82 0x20 0x12>;
+					dma-names = "rx";
+					#io-channel-cells = <1>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					nvmem-cells = <&vrefint>;
+					nvmem-cell-names = "vrefint";
+					st,adc-trigger-sel = <0>;
+					status = "disabled";
+					channel@14 {
+						reg = <14>;
+						label = "vrefint";
+					};
+					channel@15 {
+						reg = <15>;
+						label = "vddcore";
+					};
+					channel@17 {
+						reg = <17>;
+						label = "vddcpu";
+					};
+					channel@18 {
+						reg = <18>;
+						label = "vddgpu";
+					};
+				};
+			};
+
+			adc_3: adc@404f0000 {
+				compatible = "st,stm32mp23-adc-core", "st,stm32-adc-core";
+				reg = <0x404f0000 0x400>;
+				interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc CK_KER_ADC3>;
+				clock-names = "adc";
+				interrupt-controller;
+				#interrupt-cells = <1>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				access-controllers = <&rifsc 59>;
+				status = "disabled";
+
+				adc3: adc@0 {
+					compatible = "st,stm32mp23-adc", "st,stm32-adc";
+					reg = <0x0>;
+					interrupt-parent = <&adc_3>;
+					interrupts = <0>;
+					dmas = <&hpdma 83 0x20 0x12>;
+					dma-names = "rx";
+					#io-channel-cells = <1>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					nvmem-cells = <&vrefint>;
+					nvmem-cell-names = "vrefint";
+					st,adc-trigger-sel = <1>;
+					status = "disabled";
+					channel@14 {
+						reg = <14>;
+						label = "vrefint";
+					};
+					channel@15 {
+						reg = <15>;
+						label = "vddcore";
+					};
+					channel@17 {
+						reg = <17>;
+						label = "vddcpu";
+					};
+					channel@18 {
+						reg = <18>;
+						label = "vddgpu";
+					};
+				};
+			};
+
 			rng: rng@42020000 {
 				compatible = "st,stm32mp25-rng";
 				reg = <0x42020000 0x400>;

-- 
2.43.0