Linux-ARM-Kernel Archive on lore.kernel.org
 help / color / mirror / Atom feed
From: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
To: Francesco Dolcini <francesco@dolcini.it>
Cc: Leonardo Costa <leoreis.costa@gmail.com>,
	Andrzej Hajda <andrzej.hajda@intel.com>,
	Neil Armstrong <neil.armstrong@linaro.org>,
	Robert Foss <rfoss@kernel.org>, Jonas Karlman <jonas@kwiboo.se>,
	Jernej Skrabec <jernej.skrabec@gmail.com>,
	Luca Ceresoli <luca.ceresoli@bootlin.com>,
	Maarten Lankhorst <maarten.lankhorst@linux.intel.com>,
	Maxime Ripard <mripard@kernel.org>,
	Thomas Zimmermann <tzimmermann@suse.de>,
	David Airlie <airlied@gmail.com>, Simona Vetter <simona@ffwll.ch>,
	Rob Herring <robh@kernel.org>,
	Krzysztof Kozlowski <krzk+dt@kernel.org>,
	Conor Dooley <conor+dt@kernel.org>, Frank Li <Frank.Li@nxp.com>,
	Sascha Hauer <s.hauer@pengutronix.de>,
	Pengutronix Kernel Team <kernel@pengutronix.de>,
	Fabio Estevam <festevam@gmail.com>,
	dri-devel@lists.freedesktop.org, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org, imx@lists.linux.dev,
	linux-arm-kernel@lists.infradead.org,
	Leonardo Costa <leonardo.costa@toradex.com>
Subject: Re: [PATCH 0/3] Add VGA support for Apalis iMX6
Date: Tue, 13 Oct 2026 13:11:58 +0200	[thread overview]
Message-ID: <20261013111158.GG56180@killaraus.ideasonboard.com> (raw)
In-Reply-To: <20261013090631.GA33628@francesco-nb>

Hi Francesco,

On Tue, Oct 13, 2026 at 11:06:31AM +0200, Francesco Dolcini wrote:
> On Mon, Oct 12, 2026 at 06:40:54PM +0200, Laurent Pinchart wrote:
> > On Mon, Oct 12, 2026 at 04:25:22AM -0300, Leonardo Costa wrote:
> > > This series adds a device tree overlay that enables the VGA output on Apalis
> > > iMX6, which is driven from a parallel RGB interface passing through a
> > > non-programmable video DAC.
> > > 
> > > The video DAC is a simple resistor network gated by an active-low
> > > data-enable signal. For the bridge to work properly, this series also
> > > changes the following in the dt-bindings and simple-bridge driver:
> > > 
> > > - dt-bindings: Add a new compatible for the bridge in the simple-bridge
> > >   binding. This is necessary because the existing dumb-vga-dac compatible
> > >   doesn't describe a data-enable signal polarity.
> > > 
> > > - simple-bridge: Add the VGA bridge match-table entry and timings
> > >   struct, setting the DRM_BUS_FLAG_DE_LOW flag for the bridge.
> > 
> > Is there schematics available anywhere ? That would help reviewing the
> > series ?
> 
> This circuit is on the SoM, and the SoM schematics are
> confidential and not generally available.
> 
> I tried to extract as ascii art the relevant circuit, hope it helps

Thank you, it makes things clearer.

The circuit seems fairly generic. Wouldn't it be better to add an
optional property ot the dumb-vga-dac instead of a new compatible string
specific to Apalis ?

> BLUE (5 bits)
> =============
> DISP0_DATA[4] ---[R30   348R]---+
> DISP0_DATA[3] ---[R33   715R]---+
> DISP0_DATA[2] ---[R36  1.47K]---+-------- VGA1_B
> DISP0_DATA[1] ---[R39  2.94K]---+          |
> DISP0_DATA[0] ---[R42  5.90K]---+          D
>                                            |
> DI0_PIN15 ------------------------------ G | T4 MMBF2201N
>                                            S
>                                            |
>                                           GND
> 
> 
> RED (5 bits)
> ============
> DISP0_DATA[15] --[R31   348R]---+
> DISP0_DATA[14] --[R34   715R]---+
> DISP0_DATA[13] --[R37  1.47K]---+-------- VGA1_R
> DISP0_DATA[12] --[R40  2.94K]---+          |
> DISP0_DATA[11] --[R43  5.90K]---+          D
>                                            |
> DI0_PIN15 ------------------------------ G | T5 MMBF2201N
>                                            S
>                                            |
>                                           GND
> 
> 
> GREEN (6 bits)
> ==============
> DISP0_DATA[10] --[R32   348R]---+
> DISP0_DATA[9]  --[R35   715R]---+
> DISP0_DATA[8]  --[R38  1.47K]---+
> DISP0_DATA[7]  --[R41  2.94K]---+-------- VGA1_G
> DISP0_DATA[6]  --[R44  5.90K]---+          |
> DISP0_DATA[5]  --[R45  11.8K]---+          D
>                                            |
> DI0_PIN15 ------------------------------ G | T6 MMBF2201N
>                                            S
>                                            |
>                                           GND

-- 
Regards,

Laurent Pinchart


  reply	other threads:[~2026-10-13 11:12 UTC|newest]

Thread overview: 12+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-10-12  7:25 [PATCH 0/3] Add VGA support for Apalis iMX6 Leonardo Costa
2026-10-12  7:25 ` [PATCH 1/3] dt-bindings: display: bridge: simple: Add the Toradex Apalis iMX6 VGA DAC bridge Leonardo Costa
2026-10-12 16:29   ` Frank Li
2026-10-12 19:08   ` Conor Dooley
2026-10-12  7:25 ` [PATCH 2/3] drm/bridge: simple-bridge: Add Toradex RGB to " Leonardo Costa
2026-10-12 16:30   ` Frank Li
2026-10-12  7:25 ` [PATCH 3/3] ARM: dts: imx6q-apalis: Add VGA overlay Leonardo Costa
2026-10-12 16:33   ` Frank Li
2026-10-12 16:40 ` [PATCH 0/3] Add VGA support for Apalis iMX6 Laurent Pinchart
2026-10-13  9:06   ` Francesco Dolcini
2026-10-13 11:11     ` Laurent Pinchart [this message]
2026-10-13 12:50       ` Francesco Dolcini

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20261013111158.GG56180@killaraus.ideasonboard.com \
    --to=laurent.pinchart@ideasonboard.com \
    --cc=Frank.Li@nxp.com \
    --cc=airlied@gmail.com \
    --cc=andrzej.hajda@intel.com \
    --cc=conor+dt@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=dri-devel@lists.freedesktop.org \
    --cc=festevam@gmail.com \
    --cc=francesco@dolcini.it \
    --cc=imx@lists.linux.dev \
    --cc=jernej.skrabec@gmail.com \
    --cc=jonas@kwiboo.se \
    --cc=kernel@pengutronix.de \
    --cc=krzk+dt@kernel.org \
    --cc=leonardo.costa@toradex.com \
    --cc=leoreis.costa@gmail.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=luca.ceresoli@bootlin.com \
    --cc=maarten.lankhorst@linux.intel.com \
    --cc=mripard@kernel.org \
    --cc=neil.armstrong@linaro.org \
    --cc=rfoss@kernel.org \
    --cc=robh@kernel.org \
    --cc=s.hauer@pengutronix.de \
    --cc=simona@ffwll.ch \
    --cc=tzimmermann@suse.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox